Fixes the following NULL pointer dereference:
[    7.740000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.810000] Unable to handle kernel NULL pointer dereference at virtual address 00000028
[    7.810000] pgd = c3a38000
[    7.810000] [00000028] *pgd=23a8c831, *pte=00000000, *ppte=00000000
[    7.810000] Internal error: Oops: 17 [#1] PREEMPT ARM
[    7.810000] Modules linked in: ohci_hcd(+) regmap_i2c snd_pcm usbcore snd_page_alloc at91_cf snd_timer pcmcia_rsrc snd soundcore gpio_keys regmap_spi pcmcia_core usb_common nls_base
[    7.810000] CPU: 0    Not tainted  (3.6.0-rc6-mpa+ #264)
[    7.810000] PC is at __gpio_to_irq+0x18/0x40
[    7.810000] LR is at ohci_hcd_at91_overcurrent_irq+0x24/0xb4 [ohci_hcd]
[    7.810000] pc : [<c01392d4>]    lr : [<bf08f694>]    psr: 40000093
[    7.810000] sp : c3a11c40  ip : c3a11c50  fp : c3a11c4c
[    7.810000] r10: 00000000  r9 : c02dcd6e  r8 : fefff400
[    7.810000] r7 : 00000000  r6 : c02cc928  r5 : 00000030  r4 : c02dd168
[    7.810000] r3 : c02e7350  r2 : ffffffea  r1 : c02cc928  r0 : 00000000
[    7.810000] Flags: nZcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
[    7.810000] Control: c000717f  Table: 23a38000  DAC: 00000015
[    7.810000] Process modprobe (pid: 285, stack limit = 0xc3a10270)
[    7.810000] Stack: (0xc3a11c40 to 0xc3a12000)
[    7.810000] 1c40: c3a11c6c c3a11c50 bf08f694 c01392cc c3a11c84 c2c38b00 c3806900 00000030
[    7.810000] 1c60: c3a11ca4 c3a11c70 c0051264 bf08f680 c3a11cac c3a11c80 c003e764 c3806900
[    7.810000] 1c80: c2c38b00 c02cb05c c02cb000 fefff400 c3806930 c3a11cf4 c3a11cbc c3a11ca8
[    7.810000] 1ca0: c005142c c005123c c3806900 c3805a00 c3a11cd4 c3a11cc0 c0053f24 c00513e4
[    7.810000] 1cc0: c3a11cf4 00000030 c3a11cec c3a11cd8 c005120c c0053e88 00000000 00000000
[    7.810000] 1ce0: c3a11d1c c3a11cf0 c00124d0 c00511e0 01400000 00000001 00000012 00000000
[    7.810000] 1d00: ffffffff c3a11d94 00000030 00000000 c3a11d34 c3a11d20 c005120c c0012438
[    7.810000] 1d20: c001dac4 00000012 c3a11d4c c3a11d38 c0009b08 c00511e0 c00523fc 60000013
[    7.810000] 1d40: c3a11d5c c3a11d50 c0008510 c0009ab4 c3a11ddc c3a11d60 c0008eb4 c00084f0
[    7.810000] 1d60: 00000000 00000030 00000000 00000080 60000013 bf08f670 c3806900 c2c38b00
[    7.810000] 1d80: 00000030 c3806930 00000000 c3a11ddc c3a11d88 c3a11da8 c0054190 c00523fc
[    7.810000] 1da0: 60000013 ffffffff c3a11dec c3a11db8 00000000 c2c38b00 bf08f670 c3806900
[    7.810000] 1dc0: 00000000 00000080 c02cc928 00000030 c3a11e0c c3a11de0 c0052764 c00520d8
[    7.810000] 1de0: c3a11dfc 00000000 00000000 00000002 bf090f61 00000004 c02cc930 c02cc928
[    7.810000] 1e00: c3a11e4c c3a11e10 bf090978 c005269c bf090f61 c02cc928 bf093000 c02dd170
[    7.810000] 1e20: c3a11e3c c02cc930 c02cc930 bf0911d0 bf0911d0 bf093000 c3a10000 00000000
[    7.810000] 1e40: c3a11e5c c3a11e50 c0155b7c bf090808 c3a11e7c c3a11e60 c0154690 c0155b6c
[    7.810000] 1e60: c02cc930 c02cc964 bf0911d0 c3a11ea0 c3a11e9c c3a11e80 c015484c c01545e8
[    7.810000] 1e80: 00000000 00000000 c01547e4 bf0911d0 c3a11ec4 c3a11ea0 c0152e58 c01547f4
[    7.810000] 1ea0: c381b88c c384ab10 c2c10540 bf0911d0 00000000 c02d7518 c3a11ed4 c3a11ec8
[    7.810000] 1ec0: c01544c0 c0152e0c c3a11efc c3a11ed8 c01536cc c01544b0 bf091075 c3a11ee8
[    7.810000] 1ee0: bf049af0 bf09120c bf0911d0 00000000 c3a11f1c c3a11f00 c0154e9c c0153628
[    7.810000] 1f00: bf049af0 bf09120c 000ae190 00000000 c3a11f2c c3a11f20 c0155f58 c0154e04
[    7.810000] 1f20: c3a11f44 c3a11f30 bf093054 c0155f1c 00000000 00006a4f c3a11f7c c3a11f48
[    7.810000] 1f40: c0008638 bf093010 bf09120c 000ae190 00000000 c00093c4 00006a4f bf09120c
[    7.810000] 1f60: 000ae190 00000000 c00093c4 00000000 c3a11fa4 c3a11f80 c004fdc4 c000859c
[    7.810000] 1f80: c3a11fa4 000ae190 00006a4f 00016eb8 000ad018 00000080 00000000 c3a11fa8
[    7.810000] 1fa0: c0009260 c004fd58 00006a4f 00016eb8 000ae190 00006a4f 000ae100 00000000
[    7.810000] 1fc0: 00006a4f 00016eb8 000ad018 00000080 000adba0 000ad208 00000000 000ad3d8
[    7.810000] 1fe0: beaf7ae8 beaf7ad8 000172b8 b6e4e940 20000010 000ae190 00000000 00000000
[    7.810000] Backtrace:
[    7.810000] [<c01392bc>] (__gpio_to_irq+0x0/0x40) from [<bf08f694>] (ohci_hcd_at91_overcurrent_irq+0x24/0xb4 [ohci_hcd])
[    7.810000] [<bf08f670>] (ohci_hcd_at91_overcurrent_irq+0x0/0xb4 [ohci_hcd]) from [<c0051264>] (handle_irq_event_percpu+0x38/0x1a8)
[    7.810000]  r6:00000030 r5:c3806900 r4:c2c38b00
[    7.810000] [<c005122c>] (handle_irq_event_percpu+0x0/0x1a8) from [<c005142c>] (handle_irq_event+0x58/0x7c)
[    7.810000] [<c00513d4>] (handle_irq_event+0x0/0x7c) from [<c0053f24>] (handle_simple_irq+0xac/0xd8)
[    7.810000]  r5:c3805a00 r4:c3806900
[    7.810000] [<c0053e78>] (handle_simple_irq+0x0/0xd8) from [<c005120c>] (generic_handle_irq+0x3c/0x48)
[    7.810000]  r4:00000030
[    7.810000] [<c00511d0>] (generic_handle_irq+0x0/0x48) from [<c00124d0>] (gpio_irq_handler+0xa8/0xfc)
[    7.810000]  r4:00000000
[    7.810000] [<c0012428>] (gpio_irq_handler+0x0/0xfc) from [<c005120c>] (generic_handle_irq+0x3c/0x48)
[    7.810000] [<c00511d0>] (generic_handle_irq+0x0/0x48) from [<c0009b08>] (handle_IRQ+0x64/0x88)
[    7.810000]  r4:00000012
[    7.810000] [<c0009aa4>] (handle_IRQ+0x0/0x88) from [<c0008510>] (at91_aic_handle_irq+0x30/0x38)
[    7.810000]  r5:60000013 r4:c00523fc
[    7.810000] [<c00084e0>] (at91_aic_handle_irq+0x0/0x38) from [<c0008eb4>] (__irq_svc+0x34/0x60)
[    7.810000] Exception stack(0xc3a11d60 to 0xc3a11da8)
[    7.810000] 1d60: 00000000 00000030 00000000 00000080 60000013 bf08f670 c3806900 c2c38b00
[    7.810000] 1d80: 00000030 c3806930 00000000 c3a11ddc c3a11d88 c3a11da8 c0054190 c00523fc
[    7.810000] 1da0: 60000013 ffffffff
[    7.810000] [<c00520c8>] (__setup_irq+0x0/0x458) from [<c0052764>] (request_threaded_irq+0xd8/0x134)
[    7.810000] [<c005268c>] (request_threaded_irq+0x0/0x134) from [<bf090978>] (ohci_hcd_at91_drv_probe+0x180/0x41c [ohci_hcd])
[    7.810000] [<bf0907f8>] (ohci_hcd_at91_drv_probe+0x0/0x41c [ohci_hcd]) from [<c0155b7c>] (platform_drv_probe+0x20/0x24)
[    7.810000] [<c0155b5c>] (platform_drv_probe+0x0/0x24) from [<c0154690>] (driver_probe_device+0xb8/0x20c)
[    7.810000] [<c01545d8>] (driver_probe_device+0x0/0x20c) from [<c015484c>] (__driver_attach+0x68/0x88)
[    7.810000]  r7:c3a11ea0 r6:bf0911d0 r5:c02cc964 r4:c02cc930
[    7.810000] [<c01547e4>] (__driver_attach+0x0/0x88) from [<c0152e58>] (bus_for_each_dev+0x5c/0x9c)
[    7.810000]  r6:bf0911d0 r5:c01547e4 r4:00000000
[    7.810000] [<c0152dfc>] (bus_for_each_dev+0x0/0x9c) from [<c01544c0>] (driver_attach+0x20/0x28)
[    7.810000]  r7:c02d7518 r6:00000000 r5:bf0911d0 r4:c2c10540
[    7.810000] [<c01544a0>] (driver_attach+0x0/0x28) from [<c01536cc>] (bus_add_driver+0xb4/0x22c)
[    7.810000] [<c0153618>] (bus_add_driver+0x0/0x22c) from [<c0154e9c>] (driver_register+0xa8/0x144)
[    7.810000]  r7:00000000 r6:bf0911d0 r5:bf09120c r4:bf049af0
[    7.810000] [<c0154df4>] (driver_register+0x0/0x144) from [<c0155f58>] (platform_driver_register+0x4c/0x60)
[    7.810000]  r7:00000000 r6:000ae190 r5:bf09120c r4:bf049af0
[    7.810000] [<c0155f0c>] (platform_driver_register+0x0/0x60) from [<bf093054>] (ohci_hcd_mod_init+0x54/0x8c [ohci_hcd])
[    7.810000] [<bf093000>] (ohci_hcd_mod_init+0x0/0x8c [ohci_hcd]) from [<c0008638>] (do_one_initcall+0xac/0x174)
[    7.810000]  r4:00006a4f
[    7.810000] [<c000858c>] (do_one_initcall+0x0/0x174) from [<c004fdc4>] (sys_init_module+0x7c/0x1a0)
[    7.810000] [<c004fd48>] (sys_init_module+0x0/0x1a0) from [<c0009260>] (ret_fast_syscall+0x0/0x2c)
[    7.810000]  r7:00000080 r6:000ad018 r5:00016eb8 r4:00006a4f
[    7.810000] Code: e24cb004 e59f3028 e1a02000 e7930180 (e5903028)
[    7.810000] ---[ end trace 85aa37ed128143b5 ]---
[    7.810000] Kernel panic - not syncing: Fatal exception in interrupt

Commit 6fffb77c (USB: ohci-at91: fix PIO handling in relation with number of
ports) started setting unused pins to EINVAL. But this exposed a bug in the
ohci_hcd_at91_overcurrent_irq function where the gpio was used without being
checked to see if it is valid.

This patches fixed the issue by adding the gpio valid check.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Cc: stable <stable@vger.kernel.org> # [3.4+] whereever 6fffb77c went
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need to call scsi_get_host_dev(sh) but we never use the return
nor do we have any reason to check it.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for USB controller version 2.4
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The three Pantech devices UML190 (106c:3716), UML290 (106c:3718) and
P4200 (106c:3721) all use the same subclasses to identify vendor
specific functions.  Replace the existing device specific entries
with generic vendor matching, adding support for the P4200.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Cc: Thomas Schäfer <tschaefer@t-online.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Interface #5 on ZTE MF683 is a QMI/wwan interface.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Cc: Shawn J. Goff <shawn7400@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1606) converts two warning messages in the ehci-hcd
driver to debug messages, and adds a little extra information to each.

The log messages occur when an EHCI controller takes too long (more
than 20 ms) to turn its async or periodic schedule on or off.  If this
happens at all, it's liable to happen quite often and there's no point
spamming the system log with these warnings.  Furthermore, there's
nothing much we can do about it when the problem happens.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Thomas Voegtle <tv@lio96.de>
Cc: stable <stable@vger.kernel.org> # [3.6]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1605) removes a useless test from the EHCI debugfs
code.  There's no point checking whether p.qh is non-NULL; we already
know it is and in any case it gets dereferenced aerlier in the
function.

The useless test was identified by smatch.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

I fixed up all of the #ifdef stuff, so remove the comment saying it
still needs to be removed.
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Rob Duncan <rob.duncan@exar.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As reported by Fengguang:

FYI, coccinelle warns about

drivers/usb/serial/usb-serial.c:1415:3-51: code aligned with following code on line 1416

vim +1415 drivers/usb/serial/usb-serial.c

  1412          /* we only set the reset_resume field if the serial_driver has one */
  1413          for (sd = serial_drivers; *sd; ++sd) {
  1414                  if ((*sd)->reset_resume)
> 1415                          udriver->reset_resume = usb_serial_reset_resume;
> 1416                          break;
  1417          }
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: stable <stable@vger.kernel.org> [3.5]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the issue that EHCI registers, hostpc[0] and usbmode_ex,
are not correctly accessed on Tegra3 platform.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds new functions to upload firmware to the controller. The
drivers currently using ezusb are adapted to use these new functions.

This also fixes a bug occuring during firmware loading in the
whiteheat-driver:
The driver iterates over an ihex-formatted firmware using ++ on a "const
struct ihex_binrec*" which leads to faulty results, because ihex data is
read as length. The function "ihex_next_binrec(record)" has so be used
to work correctly
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This Patch adds support for the newer Cypress FX2LP. It also adapts
three drivers currently using ezusb to the interface change. (whiteheat
and keyspan[_pda])
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Just like for the in-tree early console debug port driver, the
hypervisor - when using a debug port based console - also needs to be
told about controller resets, so it can suppress using and then
re-initialize the debug port accordingly.

Other than the in-tree driver, the hypervisor driver actually cares
about doing this only for the device where the debug is port actually
in use, i.e. it needs to be told the coordinates of the device being
reset (quite obviously, leveraging the addition done for that would
likely benefit the in-tree driver too).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This moves to using pr_info() where needed instead of a "raw" printk()
call, making the whole driver more unified.

It also cleans up my email address in the MODULE_AUTHOR field.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver should not be sending any printk() messages when it is
loaded, as no other USB serial driver does.  This fixes that, and also
removes the useless version number from the driver.

Cc: Johan Hovold <jhovold@gmail.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver was calling printk() directly at startup, which is just
noise.  Switch over to using pr_info() where needed, and get rid of the
totally useless version number that had never ever been incremented.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It should be calling dev_err() instead of printk(KERN_INFO...) so this
change fixes that up properly.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These somehow got missed previously (as they weren't calling dbg(), but
rather printk() directly), so move over to using dev_dbg() as we never
want to see startup messages unless debugging is enabled.

Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Don't be telling the syslog that the driver was loaded, the majority of
the usb-serial drivers do not, so this one shouldn't either.

Also remove the pointless driver version information.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use dev_err() like the rest of that function does, and the rest of the
driver does, to properly show what device and driver caused the problem.

Cc: Johan Hovold <jhovold@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

No one needs to know that the driver is loaded (almost all other USB
serial drivers are now quiet), so just load quietly.

Also remove unused, and unneeded version information from the driver,
that was pointless.

Cc: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This code shouldn't be calling printk(), no one needs to know this debug
message, the return code is good enough.

Cc: "René Bürgel" <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try
to use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

I forgot to remove an unused variable.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.

CC: Support Department <support@connecttech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.

CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: "Bjørn Mork" <bjorn@mork.no>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.

CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Wang YanQing <Udknight@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.

CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.

CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.

CC: Johan Hovold <jhovold@gmail.com>
CC: Mark Ferrell <mferrell@uplogix.com>
CC: Donald Lee <donald@asix.com.tw>
CC: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.

CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.

CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.

CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.

CC: Johan Hovold <jhovold@gmail.com>
CC: "Eric W. Biederman" <ebiederm@xmission.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>