This patch fixes the following DTC warnings for omap3-ha-lcd.dtb:

"display@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings for omap3-gta04a3.dtb,
omap3-gta04a4.dtb and omap3-gta04a5.dtb:

"dmtimer-pwm@11 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings for omap3-devkit8000-lcd43.dtb
and omap3-devkit8000-lcd70.dtb:

"display@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings for omap3-devkit8000.dtb,
omap3-devkit8000-lcd43.dtb and omap3-devkit8000-lcd70.dtb:

"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings for omap3-cm-t3517.dtb,
omap3-cm-t3530.dtb and omap3-cm-t3730.dtb:

"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings for omap3-beagle-xm.dtb:

"encoder@0 has a unit name, but no reg property"
"encoder@0/ports/port@0/endpoint@0 has a unit name, but no reg property"
"encoder@0/ports/port@1/endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings for omap3-beagle.dtb:

"encoder@0 has a unit name, but no reg property"
"encoder@0/ports/port@0/endpoint@0 has a unit name, but no reg property"
"encoder@0/ports/port@1/endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings for omap3-n900.dtb:

"dmtimer-pwm@9 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"dmtimer-pwm@10 has a unit name, but no reg property"
"display@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings for am3517-craneboard.dtb:

"fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings for omap2430-sdp.dtb:

"func_96m_ck has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Adding DT node for hardware random number generator.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add clk node for RNG module.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Adding dt node for hardware random number generator IP.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

DRA7 SoC has the same SHA IP as OMAP5. Add DT entry for the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[t-kristo@ti.com: changed SHA to use EDMA instead of SDMA]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

DRA7 SoC has the same AES IP as OMAP4. Add DT entries for both AES cores.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[t-kristo@ti.com: squashed in the change to use EDMA, squashed in
                  support for two AES cores]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

DRA7xx SoCs have a DES3DES IP. Add DT data for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This commit adds the stdout-path propety in /chosen for all Beaglebone
boards.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The unit address of the second PCIe instance
is set to be same as that of the first instance
(copy-paste error).

Fix it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Define RFID eeprom node which is present on gta04
device.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The twl6040 codec is generating the pdmclk, which is used by the McPDM as
functional clock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The twl6040 codec is generating the pdmclk, which is used by the McPDM as
functional clock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The twl6040 codec is generating the pdmclk, which is used by the McPDM as
functional clock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The twl6040 codec is generating the pdmclk, which is used by the McPDM as
functional clock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The twl6040 codec is generating the pdmclk, which is used by the McPDM as
functional clock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add clock properties to the McBSP nodes. McBSP2 and 3 need to have ick also
since the Sidetone block of these modules are operating using the McBSP
interface clock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently am33xx.dtsi declares the MAC controller to have two
slave ports, on these boards we only use one, so set the slave
count to one. This eliminates a console error message when
the non-existent PHY is not detected.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently am4372.dtsi declares the MAC controller to have two
slave ports, on this board we only use one, so set the slave
count to one. This eliminates a console error message when
the non-existent PHY is not detected.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Correct misspelling, "emda3" -> "edma3".
Reported-by: Adam J Allison <adamj.allison@gmail.com>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Rename the tag of the 3.3 V regulator used in the DRA72 EVM in
order to have a consistent tag name with the DRA7 EVM.  This
is useful when the regulator needs to be referenced in common
dtsi files (i.e. for common companion boards like JAMR3 [1]).

[1] http://www.ti.com.cn/cn/lit/ug/sprui52/sprui52.pdfSigned-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

AM335x ICE board has a TI PCA9536 chip connected to I2C0 at address
0x41. Add DT entry for the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Kristofer Martinez <Kristofer.S.Martinez@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add an operating-points-v2 table with all OPPs available for all silicon
revisions along with necessary data for use by ti-opp driver to selectively
enable the appropriate OPPs at runtime and handle voltage transitions

As we now need to define voltage ranges for each OPP, we define the
minimum and maximum voltage to match the ranges possible for AVS class0
voltage as defined by the DRA7/AM57 Data Manual, with the exception of
using a range for OPP_OD based on historical data to ensure that SoCs
from older lots still continue to boot, even though more optimal voltages
are now the standard. Once an AVS Class0 driver is in place it will be
possible for these OPP voltages to be adjusted to any voltage within the
provided range.

Information from SPRS953, Revised December 2015.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Nearly all of the information in the cpus node, especially for cpu0, is
the same between dra74x and dra72x so move the common information to
the parent dra7.dtsi to avoid duplication of data.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Create a system control module node for the control module portion that
resides under l4_wkup.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Hook dcdc2 as the cpu0-supply.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add an operating-points-v2 table with all OPPs available for all silicon
revisions along with necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime.

Information from AM437x Data Manual, SPRS851B, Revised April 2015,
Table 5-2.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Although all PG2.0 silicon may not support 1GHz OPP for the MPU, older
Beaglebone Blacks may have PG2.0 silicon populated and these particular
parts are guaranteed to support the OPP, so enable it for PG2.0 on
am335x-boneblack only.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Drop the operating-points table present in am33xx.dtsi and add an
operating-points-v2 table with all OPPs available for all silicon
revisions along with necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime. Also, drop the voltage-tolerance
value and provide voltages for each OPP using the <target min max>
format instead.

Information from AM335x Data Manual, SPRS717i, Revised December 2015,
Table 5-7.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Now that we are moving to OPPv2 bindings and able to add 1GHz OPP for
MPU, let's update the max MPU voltage range to align with the maximum
possible value allowed in the operating-points table, which is max
target voltage of 132500 uV + 2%.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Without that change wifi card isn't probed because pwrseq is necessary for
libertas chip.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>