- 12 Jul, 2016 6 commits
-
-
J. Bruce Fields authored
[ Upstream commit d50039ea ] Also simplify the logic a bit. Cc: stable@vger.kernel.org Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Acked-by:
Trond Myklebust <trondmy@primarydata.com> Signed-off-by:
Sasha Levin <sasha.levin@oracle.com>
-
Lyude authored
[ Upstream commit 476490a9 ] Thanks to Ville Syrjälä for pointing me towards the cause of this issue. Unfortunately one of the sideaffects of having the refclk for a DPLL set to SSC is that as long as it's set to SSC, the GPU will prevent us from powering down any of the pipes or transcoders using it. A couple of BIOSes enable SSC in both PCH_DREF_CONTROL and in the DPLL configurations. This causes issues on the first modeset, since we don't expect SSC to be left on and as a result, can't successfully power down the pipes or the transcoders using it. Here's an example from this Dell OptiPlex 990: [drm:intel_modeset_init] SSC enabled by BIOS, overriding VBT which says disabled [drm:intel_modeset_init] 2 display pipes available. [drm:intel_update_cdclk] Current CD clock rate: 400000 kHz [drm:intel_update_max_cdclk] Max CD clock rate: 400000 kHz [drm:intel_update_max_cdclk] Max dotclock rate: 360000 kHz vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [drm:intel_crt_reset] crt adpa set to 0xf40000 [drm:intel_dp_init_connector] Adding DP connector on port C [drm:intel_dp_aux_init] registering DPDDC-C bus for card0-DP-1 [drm:ironlake_init_pch_refclk] has_panel 0 has_lvds 0 has_ck505 0 [drm:ironlake_init_pch_refclk] Disabling SSC entirely … later we try committing the first modeset … [drm:intel_dump_pipe_config] [CRTC:26][modeset] config ffff88041b02e800 for pipe A [drm:intel_dump_pipe_config] cpu_transcoder: A … [drm:intel_dump_pipe_config] dpll_hw_state: dpll: 0xc4016001, dpll_md: 0x0, fp0: 0x20e08, fp1: 0x30d07 [drm:intel_dump_pipe_config] planes on this crtc [drm:intel_dump_pipe_config] STANDARD PLANE:23 plane: 0.0 idx: 0 enabled [drm:intel_dump_pipe_config] FB:42, fb = 800x600 format = 0x34325258 [drm:intel_dump_pipe_config] scaler:0 src (0, 0) 800x600 dst (0, 0) 800x600 [drm:intel_dump_pipe_config] CURSOR PLANE:25 plane: 0.1 idx: 1 disabled, scaler_id = 0 [drm:intel_dump_pipe_config] STANDARD PLANE:27 plane: 0.1 idx: 2 disabled, scaler_id = 0 [drm:intel_get_shared_dpll] CRTC:26 allocated PCH DPLL A [drm:intel_get_shared_dpll] using PCH DPLL A for pipe A [drm:ilk_audio_codec_disable] Disable audio codec on port C, pipe A [drm:intel_disable_pipe] disabling pipe A ------------[ cut here ]------------ WARNING: CPU: 1 PID: 130 at drivers/gpu/drm/i915/intel_display.c:1146 intel_disable_pipe+0x297/0x2d0 [i915] pipe_off wait timed out … ---[ end trace 94fc8aa03ae139e8 ]--- [drm:intel_dp_link_down] [drm:ironlake_crtc_disable [i915]] *ERROR* failed to disable transcoder A Later modesets succeed since they reset the DPLL's configuration anyway, but this is enough to get stuck with a big fat warning in dmesg. A better solution would be to add refcounts for the SSC source, but for now leaving the source clock on should suffice. Changes since v4: - Fix calculation of final for systems with LVDS panels (fixes BUG() on CI test suite) Changes since v3: - Move temp variable into loop - Move checks for using_ssc_source to after we've figured out has_ck505 - Add using_ssc_source to debug output Changes since v2: - Fix debug output for when we disable the CPU source Changes since v1: - Leave the SSC source clock on instead of just shutting it off on all of the DPLL configurations. Cc: stable@vger.kernel.org Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Lyude <cpaul@redhat.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1465916649-10228-1-git-send-email-cpaul@redhat.comSigned-off-by:
-
Andrey Ryabinin authored
[ Upstream commit 57675cb9 ] Lengthy output of sysrq-w may take a lot of time on slow serial console. Currently we reset NMI-watchdog on the current CPU to avoid spurious lockup messages. Sometimes this doesn't work since softlockup watchdog might trigger on another CPU which is waiting for an IPI to proceed. We reset softlockup watchdogs on all CPUs, but we do this only after listing all tasks, and this may be too late on a busy system. So, reset watchdogs CPUs earlier, in for_each_process_thread() loop. Signed-off-by:
Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/1465474805-14641-1-git-send-email-aryabinin@virtuozzo.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Masami Hiramatsu authored
[ Upstream commit dcfc4724 ] Fix kprobe_fault_handler() to clear the TF (trap flag) bit of the flags register in the case of a fault fixup on single-stepping. If we put a kprobe on the instruction which caused a page fault (e.g. actual mov instructions in copy_user_*), that fault happens on the single-stepping buffer. In this case, kprobes resets running instance so that the CPU can retry execution on the original ip address. However, current code forgets to reset the TF bit. Since this fault happens with TF bit set for enabling single-stepping, when it retries, it causes a debug exception and kprobes can not handle it because it already reset itself. On the most of x86-64 platform, it can be easily reproduced by using kprobe tracer. E.g. # cd /sys/kernel/debug/tracing # echo p copy_user_enhanced_fast_string+5 > kprobe_events # echo 1 > events/kprobes/enable And you'll see a kernel panic on do_debug(), since the debug trap is not handled by kprobes. To fix this problem, we just need to clear the TF bit when resetting running kprobe. Signed-off-by:
Masami Hiramatsu <mhiramat@kernel.org> Reviewed-by:
Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com> Acked-by:
Steven Rostedt <rostedt@goodmis.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: systemtap@sourceware.org Cc: stable@vger.kernel.org # All the way back to ancient kernels Link: http://lkml.kernel.org/r/20160611140648.25885.37482.stgit@devbox [ Updated the comments. ] Signed-off-by:
-
Michal Suchanek authored
[ Upstream commit 719bd654 ] The trasfer timeout is fixed at 1000 ms. Reading a 4Mbyte flash over 1MHz SPI bus takes way longer than that. Calculate the timeout from the actual time the transfer is supposed to take and multiply by 2 for good measure. Signed-off-by:
Michal Suchanek <hramrach@gmail.com> Acked-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Marcus Weseloh authored
[ Upstream commit 47284e3e ] Allow transfers to set the transmission speed rather than using the device max_speed_hz value. The SPI core makes sure that the speed_hz value is always set on the transfer. Signed-off-by:
Marcus Weseloh <mweseloh42@gmail.com> Signed-off-by:
-
- 11 Jul, 2016 26 commits
-
-
Michal Suchanek authored
[ Upstream commit 6d9fe44b ] When testing SPI without DMA I noticed that filling the FIFO on the spi controller causes timeout. Always leave room for one byte in the FIFO. Signed-off-by:
-
James Hogan authored
[ Upstream commit 797179bc ] Copy __kvm_mips_vcpu_run() into unmapped memory, so that we can never get a TLB refill exception in it when KVM is built as a module. This was observed to happen with the host MIPS kernel running under QEMU, due to a not entirely transparent optimisation in the QEMU TLB handling where TLB entries replaced with TLBWR are copied to a separate part of the TLB array. Code in those pages continue to be executable, but those mappings persist only until the next ASID switch, even if they are marked global. An ASID switch happens in __kvm_mips_vcpu_run() at exception level after switching to the guest exception base. Subsequent TLB mapped kernel instructions just prior to switching to the guest trigger a TLB refill exception, which enters the guest exception handlers without updating EPC. This appears as a guest triggered TLB refill on a host kernel mapped (host KSeg2) address, which is not handled correctly as user (guest) mode accesses to kernel (host) segments always generate address error exceptions. Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: kvm@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 3.10.x- Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Oscar authored
[ Upstream commit ea1d39a3 ] Fix warning about tainted kernel because usb-otg-fsm has no license. WARNING: with this patch usb-otg-fsm module can be loaded but then the kernel will hang. Tested with a udoo quad board. Cc: <stable@vger.kernel.org> #v4.1+ Signed-off-by:
Oscar <oscar@naiandei.net> Signed-off-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
-
Alex Deucher authored
[ Upstream commit 05082b8b ] When executing in a PCI passthrough based virtuzliation environment, the hypervisor will usually attempt to send a PCIe bus reset signal to the ASIC when the VM reboots. In this scenario, the card is not correctly initialized, but we still consider it to be posted. Therefore, in a passthrough based environemnt we should always post the card to guarantee it is in a good state for driver initialization. Ported from amdgpu commit: amdgpu: fix asic initialization for virtualized environments Cc: Andres Rodriguez <andres.rodriguez@amd.com> Cc: Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Linus Walleij authored
[ Upstream commit 19ced623 ] The hash buffer is really HASH_BLOCK_SIZE bytes, someone must have thought that memmove takes n*u32 words by mistake. Tests work as good/bad as before after this patch. Cc: Joakim Bech <joakim.bech@linaro.org> Cc: stable@vger.kernel.org Reported-by:
David Binderman <linuxdev.baldrick@gmail.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Steve Capper authored
[ Upstream commit 56530f5d ] Currently pmd_mknotpresent will use a zero entry to respresent an invalidated pmd. Unfortunately this definition clashes with pmd_none, thus it is possible for a race condition to occur if zap_pmd_range sees pmd_none whilst __split_huge_pmd_locked is running too with pmdp_invalidate just called. This patch fixes the race condition by modifying pmd_mknotpresent to create non-zero faulting entries (as is done in other architectures), removing the ambiguity with pmd_none. [catalin.marinas@arm.com: using L_PMD_SECT_VALID instead of PMD_TYPE_SECT] Fixes: 8d962507 ("ARM: mm: Transparent huge page support for LPAE systems.") Cc: <stable@vger.kernel.org> # 3.11+ Reported-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by:
Will Deacon <will.deacon@arm.com> Cc: Russell King <linux@armlinux.org.uk> Signed-off-by:
Steve Capper <steve.capper@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Will Deacon authored
[ Upstream commit 62453188 ] In a subsequent patch, pmd_mknotpresent will clear the valid bit of the pmd entry, resulting in a not-present entry from the hardware's perspective. Unfortunately, pmd_present simply checks for a non-zero pmd value and will therefore continue to return true even after a pmd_mknotpresent operation. Since pmd_mknotpresent is only used for managing huge entries, this is only an issue for the 3-level case. This patch fixes the 3-level pmd_present implementation to take into account the valid bit. For bisectability, the change is made before the fix to pmd_mknotpresent. [catalin.marinas@arm.com: comment update regarding pmd_mknotpresent patch] Fixes: 8d962507 ("ARM: mm: Transparent huge page support for LPAE systems.") Cc: <stable@vger.kernel.org> # 3.11+ Cc: Russell King <linux@armlinux.org.uk> Cc: Steve Capper <Steve.Capper@arm.com> Signed-off-by:
-
Wei Fang authored
[ Upstream commit 72d8c36e ] sas_ata_strategy_handler() adds the works of the ata error handler to system_unbound_wq. This workqueue asynchronously runs work items, so the ata error handler will be performed concurrently on different CPUs. In this case, ->host_failed will be decreased simultaneously in scsi_eh_finish_cmd() on different CPUs, and become abnormal. It will lead to permanently inequality between ->host_failed and ->host_busy, and scsi error handler thread won't start running. IO errors after that won't be handled. Since all scmds must have been handled in the strategy handler, just remove the decrement in scsi_eh_finish_cmd() and zero ->host_busy after the strategy handler to fix this race. Fixes: 50824d6c ("[SCSI] libsas: async ata-eh") Cc: stable@vger.kernel.org Signed-off-by:
Wei Fang <fangwei1@huawei.com> Reviewed-by:
James Bottomley <jejb@linux.vnet.ibm.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Thierry Reding authored
[ Upstream commit f8a15a96 ] There are three EHCI controllers on Tegra SoCs, each with its own reset line. However, the first controller contains a set of UTMI configuration registers that are shared with its siblings. These registers will only be reset as part of the first controller's reset. For proper operation it must be ensured that the UTMI configuration registers are reset before any of the EHCI controllers are enabled, irrespective of the probe order. Commit a47cc24c ("USB: EHCI: tegra: Fix probe order issue leading to broken USB") introduced code that ensures the first controller is always reset before setting up any of the controllers, and is never again reset afterwards. This code, however, grabs the wrong reset. Each EHCI controller has two reset controls attached: 1) the USB controller reset and 2) the UTMI pads reset (really the first controller's reset). In order to reset the UTMI pads registers the code must grab the second reset, but instead it grabbing the first. Fixes: a47cc24c ("USB: EHCI: tegra: Fix probe order issue leading to broken USB") Acked-by:
Jon Hunter <jonathanh@nvidia.com> Cc: stable@vger.kernel.org Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Andrew Goodbody authored
[ Upstream commit 7b2c17f8 ] Ensure that the endpoint is stopped by clearing REQPKT before clearing DATAERR_NAKTIMEOUT before rotating the queue on the dedicated bulk endpoint. This addresses an issue where a race could result in the endpoint receiving data before it was reprogrammed resulting in a warning about such data from musb_rx_reinit before it was thrown away. The data thrown away was a valid packet that had been correctly ACKed which meant the host and device got out of sync. Signed-off-by:
Andrew Goodbody <andrew.goodbody@cambrionix.com> Cc: stable@vger.kernel.org Signed-off-by:
Bin Liu <b-liu@ti.com> Signed-off-by:
-
Andrew Goodbody authored
[ Upstream commit f3eec0cf ] shared_fifo endpoints would only get a previous tx state cleared out, the rx state was only cleared for non shared_fifo endpoints Change this so that the rx state is cleared for all endpoints. This addresses an issue that resulted in rx packets being dropped silently. Signed-off-by:
-
Hans de Goede authored
[ Upstream commit d95815ba ] I got one of these cards for testing uas with, it seems that with streams it dma-s all over the place, corrupting memory. On my first tests it managed to dma over the BIOS of the motherboard somehow and completely bricked it. Tests on another motherboard show that it does work with streams disabled. Cc: stable@vger.kernel.org Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Hans de Goede authored
[ Upstream commit 32cb0b37 ] The Acer C120 LED Projector is a USB-3 connected pico projector which takes both its power and video data from USB-3. In combination with some hubs this device does not play well with lpm, so disable lpm for it. Signed-off-by:
-
Hans de Goede authored
[ Upstream commit 81099f97 ] Properly sort all the entries by vendor id. Signed-off-by:
-
Thomas Petazzoni authored
[ Upstream commit de95c40d ] On some platforms, the clocks might be registered by a platform driver. When this is the case, the clock platform driver may very well be probed after xhci-plat, in which case the first probe() invocation of xhci-plat will receive -EPROBE_DEFER as the return value of devm_clk_get(). The current code handles that as a normal error, and simply assumes that this means that the system doesn't have a clock for the XHCI controller, and continues probing without calling clk_prepare_enable(). Unfortunately, this doesn't work on systems where the XHCI controller does have a clock, but that clock is provided by another platform driver. In order to fix this situation, we handle the -EPROBE_DEFER error condition specially, and abort the XHCI controller probe(). It will be retried later automatically, the clock will be available, devm_clk_get() will succeed, and the probe() will continue with the clock prepared and enabled as expected. In practice, such issue is seen on the ARM64 Marvell 7K/8K platform, where the clocks are registered by a platform driver. Cc: <stable@vger.kernel.org> Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Mathias Nyman authored
[ Upstream commit 3425aa03 ] If commands timeout we mark them for abortion, then stop the command ring, and turn the commands to no-ops and finally restart the command ring. If the host is working properly the no-op commands will finish and pending completions are called. If we notice the host is failing, driver clears the command ring and completes, deletes and frees all pending commands. There are two separate cases reported where host is believed to work properly but is not. In the first case we successfully stop the ring but no abort or stop command ring event is ever sent and host locks up. The second case is if a host is removed, command times out and driver believes the ring is stopped, and assumes it will be restarted, but actually ends up timing out on the same command forever. If one of the pending commands has the xhci->mutex held it will block xhci_stop() in the remove codepath which otherwise would cleanup pending commands. Add a check that clears all pending commands in case host is removed, or we are stuck timing out on the same command. Also restart the command timeout timer when stopping the command ring to ensure we recive an ring stop/abort event. Cc: stable <stable@vger.kernel.org> Tested-by:
Joe Lawrence <joe.lawrence@stratus.com> Signed-off-by:
-
Oliver Neukum authored
[ Upstream commit ed596a4a ] Flushing a work that reschedules itself is not a sensible operation. It needs to be killed. Failure to do so leads to a kernel panic in the timer code. CC: stable@vger.kernel.org Signed-off-by:
Oliver Neukum <ONeukum@suse.com> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Bin Liu authored
[ Upstream commit d246dcb2 ] [ 40.467381] ============================================= [ 40.473013] [ INFO: possible recursive locking detected ] [ 40.478651] 4.6.0-08691-g7f3db9a #37 Not tainted [ 40.483466] --------------------------------------------- [ 40.489098] usb/733 is trying to acquire lock: [ 40.493734] (&(&dev->lock)->rlock){-.....}, at: [<bf129288>] ep0_complete+0x18/0xdc [gadgetfs] [ 40.502882] [ 40.502882] but task is already holding lock: [ 40.508967] (&(&dev->lock)->rlock){-.....}, at: [<bf12a420>] ep0_read+0x20/0x5e0 [gadgetfs] [ 40.517811] [ 40.517811] other info that might help us debug this: [ 40.524623] Possible unsafe locking scenario: [ 40.524623] [ 40.530798] CPU0 [ 40.533346] ---- [ 40.535894] lock(&(&dev->lock)->rlock); [ 40.540088] lock(&(&dev->lock)->rlock); [ 40.544284] [ 40.544284] *** DEADLOCK *** [ 40.544284] [ 40.550461] May be due to missing lock nesting notation [ 40.550461] [ 40.557544] 2 locks held by usb/733: [ 40.561271] #0: (&f->f_pos_lock){+.+.+.}, at: [<c02a6114>] __fdget_pos+0x40/0x48 [ 40.569219] #1: (&(&dev->lock)->rlock){-.....}, at: [<bf12a420>] ep0_read+0x20/0x5e0 [gadgetfs] [ 40.578523] [ 40.578523] stack backtrace: [ 40.583075] CPU: 0 PID: 733 Comm: usb Not tainted 4.6.0-08691-g7f3db9a #37 [ 40.590246] Hardware name: Generic AM33XX (Flattened Device Tree) [ 40.596625] [<c010ffbc>] (unwind_backtrace) from [<c010c1bc>] (show_stack+0x10/0x14) [ 40.604718] [<c010c1bc>] (show_stack) from [<c04207fc>] (dump_stack+0xb0/0xe4) [ 40.612267] [<c04207fc>] (dump_stack) from [<c01886ec>] (__lock_acquire+0xf68/0x1994) [ 40.620440] [<c01886ec>] (__lock_acquire) from [<c0189528>] (lock_acquire+0xd8/0x238) [ 40.628621] [<c0189528>] (lock_acquire) from [<c06ad6b4>] (_raw_spin_lock_irqsave+0x38/0x4c) [ 40.637440] [<c06ad6b4>] (_raw_spin_lock_irqsave) from [<bf129288>] (ep0_complete+0x18/0xdc [gadgetfs]) [ 40.647339] [<bf129288>] (ep0_complete [gadgetfs]) from [<bf10a728>] (musb_g_giveback+0x118/0x1b0 [musb_hdrc]) [ 40.657842] [<bf10a728>] (musb_g_giveback [musb_hdrc]) from [<bf108768>] (musb_g_ep0_queue+0x16c/0x188 [musb_hdrc]) [ 40.668772] [<bf108768>] (musb_g_ep0_queue [musb_hdrc]) from [<bf12a944>] (ep0_read+0x544/0x5e0 [gadgetfs]) [ 40.678963] [<bf12a944>] (ep0_read [gadgetfs]) from [<c0284470>] (__vfs_read+0x20/0x110) [ 40.687414] [<c0284470>] (__vfs_read) from [<c0285324>] (vfs_read+0x88/0x114) [ 40.694864] [<c0285324>] (vfs_read) from [<c0286150>] (SyS_read+0x44/0x9c) [ 40.702051] [<c0286150>] (SyS_read) from [<c0107820>] (ret_fast_syscall+0x0/0x1c) This is caused by the spinlock bug in ep0_read(). Fix the two other deadlock sources in gadgetfs_setup() too. Cc: <stable@vger.kernel.org> # v3.16+ Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Steinar H. Gunderson authored
[ Upstream commit 4879efb3 ] dwc3-exynos has two problems during init if the regulators are slow to come up (for instance if the I2C bus driver is not on the initramfs) and return probe deferral. First, every time this happens, the driver leaks the USB phys created; they need to be deallocated on error. Second, since the phy devices are created before the regulators fail, this means that there's a new device to re-trigger deferred probing, which causes it to essentially go into a busy loop of re-probing the device until the regulators come up. Move the phy creation to after the regulators have succeeded, and also fix cleanup on failure. On my ODROID XU4 system (with Debian's initramfs which doesn't contain the I2C driver), this reduces the number of probe attempts (for each of the two controllers) from more than 2000 to eight. Signed-off-by:
Steinar H. Gunderson <sesse@google.com> Reviewed-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by:
Vivek Gautam <gautam.vivek@samsung.com> Fixes: d720f057 ("usb: dwc3: exynos: add nop transceiver support") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Vivek Gautam authored
[ Upstream commit c1a3acaa ] There's no need to keep one local variable for clock, and then assign the same to 'clk' member of dwc3_exynos. Just cleaning it up. Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Wenwei Tao authored
[ Upstream commit b00c52da ] When create css failed, before call css_free_rcu_fn, we remove the css id and exit the percpu_ref, but we will do these again in css_free_work_fn, so they are redundant. Especially the css id, that would cause problem if we remove it twice, since it may be assigned to another css after the first remove. tj: This was broken by two commits updating the free path without synchronizing the creation failure path. This can be easily triggered by trying to create more than 64k memory cgroups. Signed-off-by:
Wenwei Tao <ww.tao0320@gmail.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: Vladimir Davydov <vdavydov@parallels.com> Fixes: 9a1049da ("percpu-refcount: require percpu_ref to be exited explicitly") Fixes: 01e58659 ("cgroup: release css->id after css_free") Cc: stable@vger.kernel.org # v3.17+ Signed-off-by:
-
Tejun Heo authored
[ Upstream commit 6710e594 ] For non-atomic allocations, pcpu_alloc() can try to extend the area map synchronously after dropping pcpu_lock; however, the extension wasn't synchronized against chunk destruction and the chunk might get freed while extension is in progress. This patch fixes the bug by putting most of non-atomic allocations under pcpu_alloc_mutex to synchronize against pcpu_balance_work which is responsible for async chunk management including destruction. Signed-off-by:
Alexei Starovoitov <alexei.starovoitov@gmail.com> Reported-by:
Vlastimil Babka <vbabka@suse.cz> Reported-by:
-
Tejun Heo authored
[ Upstream commit 4f996e23 ] Atomic allocations can trigger async map extensions which is serviced by chunk->map_extend_work. pcpu_balance_work which is responsible for destroying idle chunks wasn't synchronizing properly against chunk->map_extend_work and may end up freeing the chunk while the work item is still in flight. This patch fixes the bug by rolling async map extension operations into pcpu_balance_work. Signed-off-by:
-
Rainer Weikusat authored
[ Upstream commit c845acb3 ] On 2015/11/06, Dmitry Vyukov reported a deadlock involving the splice system call and AF_UNIX sockets, http://lists.openwall.net/netdev/2015/11/06/24 The situation was analyzed as (a while ago) A: socketpair() B: splice() from a pipe to /mnt/regular_file does sb_start_write() on /mnt C: try to freeze /mnt wait for B to finish with /mnt A: bind() try to bind our socket to /mnt/new_socket_name lock our socket, see it not bound yet decide that it needs to create something in /mnt try to do sb_start_write() on /mnt, block (it's waiting for C). D: splice() from the same pipe to our socket lock the pipe, see that socket is connected try to lock the socket, block waiting for A B: get around to actually feeding a chunk from pipe to file, try to lock the pipe. Deadlock. on 2015/11/10 by Al Viro, http://lists.openwall.net/netdev/2015/11/10/4 The patch fixes this by removing the kern_path_create related code from unix_mknod and executing it as part of unix_bind prior acquiring the readlock of the socket in question. This means that A (as used above) will sb_start_write on /mnt before it acquires the readlock, hence, it won't indirectly block B which first did a sb_start_write and then waited for a thread trying to acquire the readlock. Consequently, A being blocked by C waiting for B won't cause a deadlock anymore (effectively, both A and B acquire two locks in opposite order in the situation described above). Dmitry Vyukov(<dvyukov@google.com>) tested the original patch. Signed-off-by:
Rainer Weikusat <rweikusat@mobileactivedefense.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
David Howells authored
[ Upstream commit ee8ac4d6 ] AF_UNIX sockets should call mknod on the top layer only and should not attempt to modify the lower layer in a layered filesystem such as overlayfs. Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
David Howells authored
[ Upstream commit a25b376b ] places where we are dealing with S_ISSOCK file creation/lookups. Signed-off-by:
-
- 23 Jun, 2016 1 commit
-
-
Sasha Levin authored
Signed-off-by:
-
- 20 Jun, 2016 7 commits
-
-
Jann Horn authored
[ Upstream commit 2f36db71 ] This prevents users from triggering a stack overflow through a recursive invocation of pagefault handling that involves mapping procfs files into virtual memory. Signed-off-by:
Jann Horn <jannh@google.com> Acked-by:
Tyler Hicks <tyhicks@canonical.com> Cc: stable@vger.kernel.org Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Jann Horn authored
[ Upstream commit e54ad7f1 ] This prevents stacking filesystems (ecryptfs and overlayfs) from using procfs as lower filesystem. There is too much magic going on inside procfs, and there is no good reason to stack stuff on top of procfs. (For example, procfs does access checks in VFS open handlers, and ecryptfs by design calls open handlers from a kernel thread that doesn't drop privileges or so.) Signed-off-by:
-
Prasun Maiti authored
[ Upstream commit 3d5fdff4 ] iwpriv app uses iw_point structure to send data to Kernel. The iw_point structure holds a pointer. For compatibility Kernel converts the pointer as required for WEXT IOCTLs (SIOCIWFIRST to SIOCIWLAST). Some drivers may use iw_handler_def.private_args to populate iwpriv commands instead of iw_handler_def.private. For those case, the IOCTLs from SIOCIWFIRSTPRIV to SIOCIWLASTPRIV will follow the path ndo_do_ioctl(). Accordingly when the filled up iw_point structure comes from 32 bit iwpriv to 64 bit Kernel, Kernel will not convert the pointer and sends it to driver. So, the driver may get the invalid data. The pointer conversion for the IOCTLs (SIOCIWFIRSTPRIV to SIOCIWLASTPRIV), which follow the path ndo_do_ioctl(), is mandatory. This patch adds pointer conversion from 32 bit to 64 bit and vice versa, if the ioctl comes from 32 bit iwpriv to 64 bit Kernel. Cc: stable@vger.kernel.org Signed-off-by:
Prasun Maiti <prasunmaiti87@gmail.com> Signed-off-by:
Ujjal Roy <royujjal@gmail.com> Tested-by:
Dibyajyoti Ghosh <dibyajyotig@gmail.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Ben Dooks authored
[ Upstream commit b66b2a0a ] The bcm_kona_gpio_reset() calls bcm_kona_gpio_write_lock_regs() with what looks like the wrong parameter. The write_lock_regs function takes a pointer to the registers, not the bcm_kona_gpio structure. Fix the warning, and probably bug by changing the function to pass reg_base instead of kona_gpio, fixing the following warning: drivers/gpio/gpio-bcm-kona.c:550:47: warning: incorrect type in argument 1 (different address spaces) expected void [noderef] <asn:2>*reg_base got struct bcm_kona_gpio *kona_gpio warning: incorrect type in argument 1 (different address spaces) expected void [noderef] <asn:2>*reg_base got struct bcm_kona_gpio *kona_gpio Cc: stable@vger.kernel.org Signed-off-by:
Ben Dooks <ben.dooks@codethink.co.uk> Acked-by:
Ray Jui <ray.jui@broadcom.com> Reviewed-by:
Markus Mayer <mmayer@broadcom.com> Signed-off-by:
-
Ricardo Ribalda Delgado authored
[ Upstream commit 11f33a6d ] Under some circumstances, a gpiochip might be half cleaned from the gpio_device list. This patch makes sure that the chip pointer is still valid, before calling the match function. [ 104.088296] BUG: unable to handle kernel NULL pointer dereference at 0000000000000090 [ 104.089772] IP: [<ffffffff813d2045>] of_gpiochip_find_and_xlate+0x15/0x80 [ 104.128273] Call Trace: [ 104.129802] [<ffffffff813d2030>] ? of_parse_own_gpio+0x1f0/0x1f0 [ 104.131353] [<ffffffff813cd910>] gpiochip_find+0x60/0x90 [ 104.132868] [<ffffffff813d21ba>] of_get_named_gpiod_flags+0x9a/0x120 ... [ 104.141586] [<ffffffff8163d12b>] gpio_led_probe+0x11b/0x360 Cc: stable@vger.kernel.org Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by:
-
Al Viro authored
[ Upstream commit 3d56c25e ] Ascend-to-parent logics in d_walk() depends on all encountered child dentries not getting freed without an RCU delay. Unfortunately, in quite a few cases it is not true, with hard-to-hit oopsable race as the result. Fortunately, the fix is simiple; right now the rule is "if it ever been hashed, freeing must be delayed" and changing it to "if it ever had a parent, freeing must be delayed" closes that hole and covers all cases the old rule used to cover. Moreover, pipes and sockets remain _not_ covered, so we do not introduce RCU delay in the cases which are the reason for having that delay conditional in the first place. Cc: stable@vger.kernel.org # v3.2+ (and watch out for __d_materialise_dentry()) Signed-off-by:
-
Srinivas Pandruvada authored
[ Upstream commit 983e600e ] When turbo is disabled, the ->set_policy() interface is broken. For example, when turbo is disabled and cpuinfo.max = 2900000 (full max turbo frequency), setting the limits results in frequency less than the requested one: Set 1000000 KHz results in 0700000 KHz Set 1500000 KHz results in 1100000 KHz Set 2000000 KHz results in 1500000 KHz This is because the limits->max_perf fraction is calculated using the max turbo frequency as the reference, but when the max P-State is capped in intel_pstate_get_min_max(), the reference is not the max turbo P-State. This results in reducing max P-State. One option is to always use max turbo as reference for calculating limits. But this will not be correct. By definition the intel_pstate sysfs limits, shows percentage of available performance. So when BIOS has disabled turbo, the available performance is max non turbo. So the max_perf_pct should still show 100%. Signed-off-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> [ rjw : Subject & changelog, rewrite in fewer lines of code ] Cc: All applicable <stable@vger.kernel.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
