- 13 Jul, 2020 35 commits
-
-
Lee Jones authored
'sg_len' and 'dma_conf' are missing correct kerneldoc documentation and 'buf_phys_addr' was misspelled. Correcting these issues fixes the following W=1 kernel build issues: mmc/host/atmel-mci.c:352: warning: Function parameter or member 'sg_len' not described in 'atmel_mci' mmc/host/atmel-mci.c:352: warning: Function parameter or member 'buf_phys_addr' not described in 'atmel_mci' mmc/host/atmel-mci.c:352: warning: Function parameter or member 'dma_conf' not described in 'atmel_mci' Cc: Ludovic Desroches <ludovic.desroches@microchip.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Link: https://lore.kernel.org/r/20200701124702.908713-7-lee.jones@linaro.orgSigned-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Lee Jones authored
No other function in the file is documented using kerneldoc and no effort to document the function arguments have been made. It's a bit of an oddity to say the least. Let's downgrade it from kerneldoc to a standard comment block instead. Fixes the following W=1 kernel build warning: drivers/mmc/host/mtk-sd.c:1030: warning: Function parameter or member 'host' not described in 'msdc_recheck_sdio_irq' Cc: Chaotian Jing <chaotian.jing@mediatek.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: linux-mediatek@lists.infradead.org Signed-off-by:
Matthias Brugger <matthias.bgg@gmail.com> Link: https://lore.kernel.org/r/20200701124702.908713-6-lee.jones@linaro.orgSigned-off-by:
-
Lee Jones authored
Describe properties; ext_cd_irq, clk_rates and no_divider (x2). Squashes the following W=1 kernel build warnings: drivers/mmc/host/sdhci-s3c.c:126: warning: Function parameter or member 'ext_cd_irq' not described in 'sdhci_s3c' drivers/mmc/host/sdhci-s3c.c:126: warning: Function parameter or member 'clk_rates' not described in 'sdhci_s3c' drivers/mmc/host/sdhci-s3c.c:126: warning: Function parameter or member 'no_divider' not described in 'sdhci_s3c' drivers/mmc/host/sdhci-s3c.c:139: warning: Function parameter or member 'no_divider' not described in 'sdhci_s3c_drv_data' Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Link: https://lore.kernel.org/r/20200701124702.908713-5-lee.jones@linaro.orgSigned-off-by:
-
Lee Jones authored
Remainder of the kerneldoc descriptions look present and correct. Fixes the following W=1 kernel build warnings: drivers/mmc/core/regulator.c:178: warning: Function parameter or member 'mmc' not described in 'mmc_regulator_set_vqmmc' drivers/mmc/core/regulator.c:178: warning: Function parameter or member 'ios' not described in 'mmc_regulator_set_vqmmc' Signed-off-by:
-
Lee Jones authored
Add missing kerneldoc entry for sdio_set_host_pm_flags()'s 'flag' function argument. Fixes the following W=1 kernel build warning: kernel/drivers/mmc/core/sdio_io.c:722: warning: Function parameter or member 'flags' not described in 'sdio_set_host_pm_flags' Cc: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by:
-
Lee Jones authored
Not all source files which include quirks.h make use of the all of the available fixup information. When this happens the compiler complains that some constant variables are defined by never used. We can fix this by telling the compiler that this intentional by simply marking them as __maybe_unused. Fixes the following W=1 kernel build warnings: In file included from drivers/mmc/core/sdio.c:22: drivers/mmc/core/quirks.h:105:31: warning: ‘mmc_ext_csd_fixups’ defined but not used [-Wunused-const-variable=] 105 | static const struct mmc_fixup mmc_ext_csd_fixups[] = { | ^~~~~~~~~~~~~~~~~~ drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=] 17 | static const struct mmc_fixup mmc_blk_fixups[] = { | ^~~~~~~~~~~~~~ In file included from drivers/mmc/core/mmc.c:25: drivers/mmc/core/quirks.h:123:31: warning: ‘sdio_fixup_methods’ defined but not used [-Wunused-const-variable=] 123 | static const struct mmc_fixup sdio_fixup_methods[] = { | ^~~~~~~~~~~~~~~~~~ drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=] 17 | static const struct mmc_fixup mmc_blk_fixups[] = { | ^~~~~~~~~~~~~~ Cc: Andrei Warkentin <andreiw@motorola.com> Cc: Martin Mares <mj@ucw.cz> Signed-off-by: -
Hulk Robot authored
Fix sparse build warning: drivers/mmc/host/sdhci-msm.c:1888:6: warning: symbol 'sdhci_msm_dump_vendor_regs' was not declared. Should it be static? Signed-off-by:
Hulk Robot <hulkci@huawei.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200702020347.77214-1-weiyongjun1@huawei.comSigned-off-by:
-
Yoshihiro Shimoda authored
If this controller doesn't issue interrupt for response of command, this driver lacks to call dma_unmap_sg(). So, fix the issue by using end() of struct tmio_mmc_dma_ops. Reported-by:
Takeshi Saito <takeshi.saito.xv@renesas.com> Fixes: 2a68ea78 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC") Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/1590044466-28372-4-git-send-email-yoshihiro.shimoda.uh@renesas.comTested-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
-
Yoshihiro Shimoda authored
To add end() operation in the future, clean the code of renesas_sdhi_internal_dmac_complete_tasklet_fn(). No behavior change. Signed-off-by:
-
Yoshihiro Shimoda authored
Related drivers like renesas_sdhi_internal_dmac are possible to lack dma unmaping in error cases (for example response timeout). Since tmio_mmc_finish_request() will be always called in any case, to fix the issue, add end operation into struct tmio_mmc_dma_ops and call the operation in tmio_mmc_finish_request() to call dma_ummap API by the related drivers correctly. Signed-off-by:
-
Pali Rohár authored
Define appropriate macro names for consistency with other macros. Signed-off-by:
Pali Rohár <pali@kernel.org> Link: https://lore.kernel.org/r/20200629072144.24351-1-pali@kernel.orgSigned-off-by:
-
Veerabhadrarao Badiganti authored
On qcom SD host controllers voltage switching be done after the HW is ready for it. The HW informs its readiness through power irq. The voltage switching should happen only then. Use the internal voltage switching and then control the voltage switching using power irq. IO-bus supply of eMMC would be kept always-on. So set the load for this supply to configure it in LPM when eMMC is suspend state and in HPM when eMMC is active. Co-developed-by:
Asutosh Das <asutoshd@codeaurora.org> Signed-off-by:
Vijay Viswanath <vviswana@codeaurora.org> Signed-off-by:
Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Signed-off-by:
-
Veerabhadrarao Badiganti authored
Set the default power mode, MMC_POWER_UNDEFINED, in mmc_alloc_host() rather than in mmc_start_host(). This enables host drivers to make use of the initial state during ->probe(). Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Link: https://lore.kernel.org/r/1592919288-1020-3-git-send-email-vbadigan@codeaurora.orgSigned-off-by:
-
Vijay Viswanath authored
If vendor platform drivers are controlling whole logic of voltage switching, then sdhci driver no need control vqmmc regulator. So skip enabling/disable vqmmc from SDHC driver. Signed-off-by:
-
Akshu Agrawal authored
HS400/HS200/eMMC HS doesn't have Preset Value register. Hence, sdhci_set_ios function overrides the value set by fmw to SDHCI_CTRL_DRV_TYPE_B. This patch sets drv_type to MMC_SET_DRIVER_TYPE_A so that host_control2 register gets updated with the required strength value. Signed-off-by:
Akshu Agrawal <akshu.agrawal@amd.com> Acked-by:
-
Haibo Chen authored
USDHC of i.MX has internal IC debug register, which record the IC logical status. So dump these logical status in error condition, this can help analyzing issue. Signed-off-by:
Haibo Chen <haibo.chen@nxp.com> Acked-by:
-
Haibo Chen authored
In current code logic, when work in SDR12/SDR25 mode, the final clock rate is incorrect, just the legancy 400KHz, because the card->sw_caps.sd3_bus_mode do not has the flag SD_MODE_UHS_SDR12 or SD_MODE_UHS_SDR25. Besides, SDIO_SPEED_SDR12 is actually value 0, and every mode need to config the timing and clock rate, so remove the ‘if’ operator. Signed-off-by:
-
Faiz Abbas authored
Add support for writing new clkbuf_sel property for the J721e 4 bit IP. Signed-off-by:
Faiz Abbas <faiz_abbas@ti.com> Signed-off-by:
Sekhar Nori <nsekhar@ti.com> Link: https://lore.kernel.org/r/20200619125801.9530-7-faiz_abbas@ti.comSigned-off-by:
-
Faiz Abbas authored
For speed modes where DLL is not enabled write to TXDLYCLK to enable transmitter delay chain mode. Signed-off-by:
-
Faiz Abbas authored
The clock > CLOCK_TOO_SLOW_HZ condition gating phy configuration is only required because dll should not be enabled at too low a clock frequency or too low timing. Make sure that this condition only gates dll enablement. Signed-off-by:
-
Faiz Abbas authored
Add Support for AM65x PG2.0. Use the SoC bus framework to fixup the driver data and skip do DLL calibration if the revision is 1.0 Signed-off-by:
-
Faiz Abbas authored
Not all controllers need calibration for the PHY DLL. Add a DLL_CALIB flag to indicate the same. Signed-off-by:
-
Faiz Abbas authored
Add documentation for the clock buffer select phy property in the am654x and j721e 4 bit IP Signed-off-by:
-
Jisheng Zhang authored
Convert the pwrseq binding to DT schema format using json-schema. At the same time, fix a couple of issues with the examples discovered by the validation tool -- missing ";" Signed-off-by:
Jisheng Zhang <Jisheng.Zhang@synaptics.com> Link: https://lore.kernel.org/r/20200622164431.3dbc8c5a@xhacker.debianSigned-off-by:
-
Geert Uytterhoeven authored
"K" stands for "kelvin". While at it, make the spacing before units consistent. Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20200618080321.16678-1-geert+renesas@glider.beReviewed-by:
-
Flavio Suligoi authored
Fix typo: "trigered" --> "triggered" Signed-off-by:
Flavio Suligoi <f.suligoi@asem.it> Acked-by:
-
Ludovic Barre authored
This patch adds datactrl_mask_sdio for sdmmc revisions. sdmmc revisions used same bit of previous ST variant. Signed-off-by:
Ludovic Barre <ludovic.barre@st.com> Link: https://lore.kernel.org/r/20200611132839.4515-1-ludovic.barre@st.comSigned-off-by:
-
Chuhong Yuan authored
These functions do not check the return value of devm_clk_register(): - sdhci_arasan_register_sdcardclk() - sdhci_arasan_register_sampleclk() Therefore, add the missed checks to fix them. Fixes: c390f211 ("mmc: sdhci-of-arasan: Add ability to export card clock") Signed-off-by:
Chuhong Yuan <hslester96@gmail.com> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20200608162226.3259186-1-hslester96@gmail.comSigned-off-by:
-
Yue Hu authored
Commit 6b5eda36 ("sdio: put active devices into 1-bit mode during suspend") disabled 4-bit mode during system suspend. After this patch, commit 7310ece8 ("mmc: implement SD-combo (IO+mem) support") used new sdio_enable_4bit_bus() instead of sdio_enable_wide() to support SD-combo cards, also for card resume. However, no corresponding support added during suspend. That is not correct. Let's fix it. Signed-off-by:
Yue Hu <huyue2@yulong.com> Link: https://lore.kernel.org/r/20200609081431.6376-1-zbestahu@gmail.comSigned-off-by:
-
Yue Hu authored
If the card type is SD combo(MMC_TYPE_SD_COMBO) and the memory part does not support wider bus(SD_SCR_BUS_WIDTH_4), nothing will be done except return 0. However, we should check whether IO part support wider bus or not. We should use available IO ability if supported. In addition, there's a duplicated check to MMC_CAP_4_BIT_DATA since sdio_enable_wide() will include that check. And we can also save one call site to sdio_enable_wide() after this change. Signed-off-by:
-
Yue Hu authored
We should return any possible error returned by mmc_io_rw_direct() rather than only -EIO in sdio_disable_func() failure path. Signed-off-by:
-
Sowjanya Komatineni authored
This patch adds comments about NVQUIRKS HAS_PADCALIB and NEEDS_PAD_CONTROL. Signed-off-by:
Sowjanya Komatineni <skomatineni@nvidia.com> Link: https://lore.kernel.org/r/1591326240-28928-1-git-send-email-skomatineni@nvidia.comSigned-off-by:
-
Pradeep P V K authored
Add interconnect bandwidth scaling supported strings for qcom-sdhci controller. Signed-off-by:
Pradeep P V K <ppvk@codeaurora.org> Acked-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/1591691846-7578-3-git-send-email-ppvk@codeaurora.orgSigned-off-by:
-
Pradeep P V K authored
Interconnect bandwidth scaling support is now added as a part of OPP. So, make sure interconnect driver is ready before handling interconnect scaling. Signed-off-by:
Sibi Sankar <sibis@codeaurora.org> Reviewed-by:
Matthias Kaehlcke <mka@chromium.org> Link: https://lore.kernel.org/r/1591691846-7578-2-git-send-email-ppvk@codeaurora.orgSigned-off-by:
-
Ulf Hansson authored
The approach to allow userspace ~5s to consume the uevent, which is triggered when a new card is inserted/initialized, currently requires the mmc host to support system wakeup. This is unnecessary limiting, especially for an mmc host that relies on a GPIO IRQ for card detect. More precisely, the mmc host may not support system wakeup for its corresponding struct device, while the GPIO IRQ still could be configured as a wakeup IRQ via enable_irq_wake(). To support all various cases, let's simply drop the need for the wakeup support. Instead let's always register a wakeup source and activate it for all card detect IRQs by calling __pm_wakeup_event(). Signed-off-by:
-
- 12 Jul, 2020 5 commits
-
-
Linus Torvalds authored
-
git://github.com/jcmvbkbc/linux-xtensaLinus Torvalds authored
Pull Xtensa fixes from Max Filippov: - fix __sync_fetch_and_{and,or}_4 declarations to avoid build warning - update *pos in cpuinfo_op.next to avoid runtime warning - use for_each_set_bit in xtensa_pmu_irq_handler instead of open-coding it * tag 'xtensa-20200712' of git://github.com/jcmvbkbc/linux-xtensa: xtensa: simplify xtensa_pmu_irq_handler xtensa: update *pos in cpuinfo_op.next xtensa: fix __sync_fetch_and_{and,or}_4 declarations -
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull io_uring fixes from Jens Axboe: "Two late fixes again: - Fix missing msg_name assignment in certain cases (Pavel) - Correct a previous fix for full coverage (Pavel)" * tag 'io_uring-5.8-2020-07-12' of git://git.kernel.dk/linux-block: io_uring: fix not initialised work->flags io_uring: fix missing msg_name assignment
-
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linuxLinus Torvalds authored
Pull btrfs fixes from David Sterba: "Two refcounting fixes and one prepartory patch for upcoming splice cleanup: - fix double put of block group with nodatacow - fix missing block group put when remounting with discard=async - explicitly set splice callback (no functional change), to ease integrating splice cleanup patches" * tag 'for-5.8-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: btrfs: wire up iter_file_splice_write btrfs: fix double put of block group with nocow btrfs: discard: add missing put when grabbing block group from unused list -
Pavel Begunkov authored
59960b9d ("io_uring: fix lazy work init") tried to fix missing io_req_init_async(), but left out work.flags and hash. Do it earlier. Fixes: 7cdaf587 ("io_uring: avoid whole io_wq_work copy for requests completed inline") Signed-off-by:
Pavel Begunkov <asml.silence@gmail.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk>
-
