[ Upstream commit 989dbe4a ]

This group of new pins is not in the pin quirk table yet, adding
them to the pin quirk table to fix the headset-mic problem.

Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 265e9098 ]

In crypt_set_key(), if a failure occurs while replacing the old key
(e.g. tfm->setkey() fails) the key must not have DM_CRYPT_KEY_VALID flag
set.  Otherwise, the crypto layer would have an invalid key that still
has DM_CRYPT_KEY_VALID flag set.

Cc: stable@vger.kernel.org
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit f064a0de ]

The hashed page table MMU in POWER processors can update the R
(reference) and C (change) bits in a HPTE at any time until the
HPTE has been invalidated and the TLB invalidation sequence has
completed.  In kvmppc_h_protect, which implements the H_PROTECT
hypercall, we read the HPTE, modify the second doubleword,
invalidate the HPTE in memory, do the TLB invalidation sequence,
and then write the modified value of the second doubleword back
to memory.  In doing so we could overwrite an R/C bit update done
by hardware between when we read the HPTE and when the TLB
invalidation completed.  To fix this we re-read the second
doubleword after the TLB invalidation and OR in the (possibly)
new values of R and C.  We can use an OR since hardware only ever
sets R and C, never clears them.

This race was found by code inspection.  In principle this bug could
cause occasional guest memory corruption under host memory pressure.

Fixes: a8606e20 ("KVM: PPC: Handle some PAPR hcalls in the kernel", 2011-06-29)
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 0d808df0 ]

When switching from/to a guest that has a transaction in progress,
we need to save/restore the checkpointed register state.  Although
XER is part of the CPU state that gets checkpointed, the code that
does this saving and restoring doesn't save/restore XER.

This fixes it by saving and restoring the XER.  To allow userspace
to read/write the checkpointed XER value, we also add a new ONE_REG
specifier.

The visible effect of this bug is that the guest may see its XER
value being corrupted when it uses transactions.

Fixes: e4e38121 ("KVM: PPC: Book3S HV: Add transactional memory support")
Fixes: 0a8eccef ("KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit c48ae41b ]

The commit "ext4: sanity check the block and cluster size at mount
time" should prevent any problems, but in case the superblock is
modified while the file system is mounted, add an extra safety check
to make sure we won't overrun the allocated buffer.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit cd6bb35b ]

Centralize the checks for inodes_per_block and be more strict to make
sure the inodes_per_block_group can't end up being zero.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 9e47a4c9 ]

If the block size or cluster size is insane, reject the mount.  This
is important for security reasons (although we shouldn't be just
depending on this check).

Ref: http://www.securityfocus.com/archive/1/539661
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1332506Reported-by: Borislav Petkov <bp@alien8.de>
Reported-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 37be6676 ]

USB-3 does not have any link state that will avoid negotiating a connection
with a plugged-in cable but will signal the host when the cable is
unplugged.

For USB-3 we used to first set the link to Disabled, then to RxDdetect to
be able to detect cable connects or disconnects. But in RxDetect the
connected device is detected again and eventually enabled.

Instead set the link into U3 and disable remote wakeups for the device.
This is what Windows does, and what Alan Stern suggested.

Cc: stable@vger.kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 8052d724 ]

When there is a CRC error in the SPROM read from the device, the code
attempts to handle a fallback SPROM. When this also fails, the driver
returns zero rather than an error code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 79e57dd1 ]

The active_high LED of my Wistron DNMA-92 is still being recognized as
active_low on 4.7.6 mainline. When I was preparing my former commit
0f9edcdd ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92
cards.") to fix that I must have somehow messed up with testing, because
I tested the final version of that patch before sending it, and it was
apparently working; but now it is not working on 4.7.6 mainline.

I initially added the PCI_DEVICE_SUB section for 0x0029/0x2096 above the
PCI_VDEVICE section for 0x0029; but then I moved the former below the
latter after seeing how 0x002A sections were sorted in the file.

This turned out to be wrong: if a generic PCI_VDEVICE entry (that has
both subvendor and subdevice IDs set to PCI_ANY_ID) is put before a more
specific one (PCI_DEVICE_SUB), then the generic PCI_VDEVICE entry will
match first and will be used.

With this patch, 0x0029/0x2096 has finally got active_high LED on 4.7.6.

While I'm at it, let's fix 0x002A too by also moving its generic definition
below its specific ones.

Fixes: 0f9edcdd ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92 cards.")
Cc: <stable@vger.kernel.org> #4.7+
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
[kvalo@qca.qualcomm.com: improve the commit log based on email discussions]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 655c4d44 ]

For NI M Series cards, the Comedi `insn_read` handler for the AI
subdevice is broken due to ANDing the value read from the AI FIFO data
register with an incorrect mask.  The incorrect mask clears all but the
most significant bit of the sample data.  It should preserve all the
sample data bits.  Correct it.

Fixes: 817144ae ("staging: comedi: ni_mio_common: remove unnecessary use of 'board->adbits'")
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 30a9d7af ]

The number of 'counters' elements needed in 'struct sg' is
super_block->s_blocksize_bits + 2. Presently we have 16 'counters'
elements in the array. This is insufficient for block sizes >= 32k. In
such cases the memcpy operation performed in ext4_mb_seq_groups_show()
would cause stack memory corruption.

Fixes: c9de560dSigned-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 69e43e8c ]

'border' variable is set to a value of 2 times the block size of the
underlying filesystem. With 64k block size, the resulting value won't
fit into a 16-bit variable. Hence this commit changes the data type of
'border' to 'unsigned int'.

Fixes: c9de560dSigned-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit b4a567e8 ]

->queue_rq() should return one of the BLK_MQ_RQ_QUEUE_* constants, not
an errno.

f4aa4c7b ("block: loop: convert to per-device workqueue")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit d128af17 ]

The AEAD givenc descriptor relies on moving the IV through the
output FIFO and then back to the CTX2 for authentication. The
SEQ FIFO STORE could be scheduled before the data can be
read from OFIFO, especially since the SEQ FIFO LOAD needs
to wait for the SEQ FIFO LOAD SKIP to finish first. The
SKIP takes more time when the input is SG than when it's
a contiguous buffer. If the SEQ FIFO LOAD is not scheduled
before the STORE, the DECO will hang waiting for data
to be available in the OFIFO so it can be transferred to C2.
In order to overcome this, first force transfer of IV to C2
by starting the "cryptlen" transfer first and then starting to
store data from OFIFO to the output buffer.

Fixes: 1acebad3 ("crypto: caam - faster aead implementation")
Cc: <stable@vger.kernel.org> # 3.2+
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 295070e9 ]

The regulator has never been properly enabled, it has been
dormant all the time. It's strange that MMC was working
at all, but it likely worked by the signals going through
the levelshifter and reaching the card anyways.

Fixes: 3615a34e ("regulator: add STw481x VMMC driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit ccdb6be9 ]

The UHCI controllers in Intel chipsets rely on a platform-specific non-PME
mechanism for wakeup signalling.  They can generate wakeup signals even
though they don't support PME.

We need to let the USB core know this so that it will enable runtime
suspend for UHCI controllers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: stable@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 6496ebd7 ]

One some systems, the firmware does not allow certain PCI devices to be put
in deep D-states.  This can cause problems for wakeup signalling, if the
device does not support PME# in the deepest allowed suspend state.  For
example, Pierre reports that on his system, ACPI does not permit his xHCI
host controller to go into D3 during runtime suspend -- but D3 is the only
state in which the controller can generate PME# signals.  As a result, the
controller goes into runtime suspend but never wakes up, so it doesn't work
properly.  USB devices plugged into the controller are never detected.

If the device relies on PME# for wakeup signals but is not capable of
generating PME# in the target state, the PCI core should accurately report
that it cannot do wakeup from runtime suspend.  This patch modifies the
pci_dev_run_wake() routine to add this check.
Reported-by: Pierre de Villemereuil <flyos@mailoo.org>
Tested-by: Pierre de Villemereuil <flyos@mailoo.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org
CC: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 18e1c7f6 ]

For SRIOV enabled firmware, if there is a OCR(online controller reset)
possibility driver set the convert flag to 1, which is not happening if
there are outstanding commands even after 180 seconds.  As driver does
not set convert flag to 1 and still making the OCR to run, VF(Virtual
function) driver is directly writing on to the register instead of
waiting for 30 seconds. Setting convert flag to 1 will cause VF driver
will wait for 30 secs before going for reset.

CC: stable@vger.kernel.org
Signed-off-by: Kiran Kumar Kasturi <kiran-kumar.kasturi@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 0a97c81a ]

Hook up drm_compat_ioctl to support 32-bit userspace on 64-bit kernels.
It turns out that N2600 and N2800 comes with 64-bit enabled. We
previously assumed there where no such systems out there.

Cc: stable@vger.kernel.org
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161101144315.2955-1-patrik.r.jakobsson@gmail.comSigned-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit e8f29bb7 ]

usb_endpoint_maxp() returns wMaxPacketSize in its
raw form. Without taking into consideration that it
also contains other bits reserved for isochronous
endpoints.

This patch fixes one occasion where this is a
problem by making sure that we initialize
ep->maxpacket only with lower 10 bits of the value
returned by usb_endpoint_maxp(). Note that seperate
patches will be necessary to audit all call sites of
usb_endpoint_maxp() and make sure that
usb_endpoint_maxp() only returns lower 10 bits of
wMaxPacketSize.

Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 5f12b80a ]

We use obj->phys_handle to choose the pread/pwrite path, but as
obj->phys_handle is a union with obj->userptr, we then mistakenly use
the phys_handle path for userptr objects within pread/pwrite.

Testcase: igt/gem_userptr_blits/forbidden-operations
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97519Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161003124516.12388-2-chris@chris-wilson.co.ukSigned-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 0727e40a ]

Bspec says:
  "The mailbox response data may not account for memory read latency.
   If the mailbox response data for level 0 is 0us, add 2 microseconds
   to the result for each valid level."

This means we should only do the +2 in case wm[0] == 0, not always.

So split the sanitizing implementation from the WA implementation and
fix the WA implementation.

v2: Add Fixes tag (Maarten).

Fixes: 367294be ("drm/i915/gen9: Add 2us read latency to WM level")
Cc: stable@vger.kernel.org
Cc: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474578035-424-5-git-send-email-paulo.r.zanoni@intel.comSigned-off-by: Sasha Levin <alexander.levin@verizon.com>

Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 5e5ec175 ]

This patch will fix regression caused by commit 1e793f6f ("scsi:
megaraid_sas: Fix data integrity failure for JBOD (passthrough)
devices").

The problem was that the MEGASAS_IS_LOGICAL macro did not have braces
and as a result the driver ended up exposing a lot of non-existing SCSI
devices (all SCSI commands to channels 1,2,3 were returned as
SUCCESS-DID_OK by driver).

[mkp: clarified patch description]

Fixes: 1e793f6fReported-by: Jens Axboe <axboe@kernel.dk>
CC: stable@vger.kernel.org
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Tested-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Tested-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 3de81b75 ]

Qian Zhang (张谦) reported a potential socket buffer overflow in
tipc_msg_build() which is also known as CVE-2016-8632: due to
insufficient checks, a buffer overflow can occur if MTU is too short for
even tipc headers. As anyone can set device MTU in a user/net namespace,
this issue can be abused by a regular user.

As agreed in the discussion on Ben Hutchings' original patch, we should
check the MTU at the moment a bearer is attached rather than for each
processed packet. We also need to repeat the check when bearer MTU is
adjusted to new device MTU. UDP case also needs a check to avoid
overflow when calculating bearer MTU.

References: CVE-2016-8632
Fixes: b97bf3fd ("[TIPC] Initial merge")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reported-by: Qian Zhang (张谦) <zhangqian-c@360.cn>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	net/tipc/bearer.c
	net/tipc/bearer.h
due to 1a90632d: tipc: eliminate remnants of hungarian notation
and b1c29f6b tipc: simplify resetting and disabling of bearers
Signed-off-by: Philipp Hahn <hahn@univention.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 0eab121e ]

Prior to commit c0371da6 ("put iov_iter into msghdr") in v3.19, there
was no check that the iovec contained enough bytes for an ICMP header,
and the read loop would walk across neighboring stack contents. Since the
iov_iter conversion, bad arguments are noticed, but the returned error is
EFAULT. Returning EINVAL is a clearer error and also solves the problem
prior to v3.19.

This was found using trinity with KASAN on v3.18:

BUG: KASAN: stack-out-of-bounds in memcpy_fromiovec+0x60/0x114 at addr ffffffc071077da0
Read of size 8 by task trinity-c2/9623
page:ffffffbe034b9a08 count:0 mapcount:0 mapping:          (null) index:0x0
flags: 0x0()
page dumped because: kasan: bad access detected
CPU: 0 PID: 9623 Comm: trinity-c2 Tainted: G    BU         3.18.0-dirty #15
Hardware name: Google Tegra210 Smaug Rev 1,3+ (DT)
Call trace:
[<ffffffc000209c98>] dump_backtrace+0x0/0x1ac arch/arm64/kernel/traps.c:90
[<ffffffc000209e54>] show_stack+0x10/0x1c arch/arm64/kernel/traps.c:171
[<     inline     >] __dump_stack lib/dump_stack.c:15
[<ffffffc000f18dc4>] dump_stack+0x7c/0xd0 lib/dump_stack.c:50
[<     inline     >] print_address_description mm/kasan/report.c:147
[<     inline     >] kasan_report_error mm/kasan/report.c:236
[<ffffffc000373dcc>] kasan_report+0x380/0x4b8 mm/kasan/report.c:259
[<     inline     >] check_memory_region mm/kasan/kasan.c:264
[<ffffffc00037352c>] __asan_load8+0x20/0x70 mm/kasan/kasan.c:507
[<ffffffc0005b9624>] memcpy_fromiovec+0x5c/0x114 lib/iovec.c:15
[<     inline     >] memcpy_from_msg include/linux/skbuff.h:2667
[<ffffffc000ddeba0>] ping_common_sendmsg+0x50/0x108 net/ipv4/ping.c:674
[<ffffffc000dded30>] ping_v4_sendmsg+0xd8/0x698 net/ipv4/ping.c:714
[<ffffffc000dc91dc>] inet_sendmsg+0xe0/0x12c net/ipv4/af_inet.c:749
[<     inline     >] __sock_sendmsg_nosec net/socket.c:624
[<     inline     >] __sock_sendmsg net/socket.c:632
[<ffffffc000cab61c>] sock_sendmsg+0x124/0x164 net/socket.c:643
[<     inline     >] SYSC_sendto net/socket.c:1797
[<ffffffc000cad270>] SyS_sendto+0x178/0x1d8 net/socket.c:1761

CVE-2016-8399
Reported-by: Qidan He <i@flanker017.me>
Fixes: c319b4d7 ("net: ipv4: add IPPROTO_ICMP socket kind")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Philipp Hahn <hahn@univention.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 84ac7260 ]

When packet_set_ring creates a ring buffer it will initialize a
struct timer_list if the packet version is TPACKET_V3. This value
can then be raced by a different thread calling setsockopt to
set the version to TPACKET_V1 before packet_set_ring has finished.

This leads to a use-after-free on a function pointer in the
struct timer_list when the socket is closed as the previously
initialized timer will not be deleted.

The bug is fixed by taking lock_sock(sk) in packet_setsockopt when
changing the packet version while also taking the lock at the start
of packet_set_ring.

References: CVE-2016-8655
Fixes: f6fb8f10 ("af-packet: TPACKET_V3 flexible buffer implementation.")
Signed-off-by: Philip Pettersson <philip.pettersson@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Philipp Hahn <hahn@univention.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Debian: net-add-recursion-limit-to-gro.patch ]

Currently, GRO can do unlimited recursion through the gro_receive
handlers.  This was fixed for tunneling protocols by limiting tunnel GRO
to one level with encap_mark, but both VLAN and TEB still have this
problem.  Thus, the kernel is vulnerable to a stack overflow, if we
receive a packet composed entirely of VLAN headers.

This patch adds a recursion counter to the GRO layer to prevent stack
overflow.  When a gro_receive function hits the recursion limit, GRO is
aborted for this skb and it is processed normally.

Thanks to Vladimír Beneš <vbenes@redhat.com> for the initial bug report.

Fixes: CVE-2016-7039
Fixes: 9b174d88 ("net: Add Transparent Ethernet Bridging GRO support.")
Fixes: 66e5133f ("vlan: Add GRO support for non hardware accelerated vlan")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Philipp Hahn <hahn@univention.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 951b6a07 ]

addr can be NULL and it should not be dereferenced before NULL checking.

References: CVE-2015-8956
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Philipp Hahn <hahn@univention.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ bugfix/all/ptrace-being-capable-wrt-a-process-requires-mapped-uids-gids.patch ]

ptrace_has_cap() checks whether the current process should be
treated as having a certain capability for ptrace checks
against another process. Until now, this was equivalent to
has_ns_capability(current, target_ns, CAP_SYS_PTRACE).

However, if a root-owned process wants to enter a user
namespace for some reason without knowing who owns it and
therefore can't change to the namespace owner's uid and gid
before entering, as soon as it has entered the namespace,
the namespace owner can attach to it via ptrace and thereby
gain access to its uid and gid.

While it is possible for the entering process to switch to
the uid of a claimed namespace owner before entering,
causing the attempt to enter to fail if the claimed uid is
wrong, this doesn't solve the problem of determining an
appropriate gid.

With this change, the entering process can first enter the
namespace and then safely inspect the namespace's
properties, e.g. through /proc/self/{uid_map,gid_map},
assuming that the namespace owner doesn't have access to
uid 0.
Changed in v2: The caller needs to be capable in the
namespace into which tcred's uids/gids can be mapped.

Rederences: CVE-2015-8709
References: https://lkml.org/lkml/2015/12/25/71Signed-off-by: Jann Horn <jann@thejh.net>
Signed-off-by: Philipp Hahn <hahn@univention.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 7bc2b55a ]

We need to put an upper bound on "user_len" so the memcpy() doesn't
overflow.

References: CVE-2016-7425
Cc: <stable@vger.kernel.org>
Reported-by: Marco Grassi <marco.gra@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Philipp Hahn <hahn@univention.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit d2921684 ]

CAI Qian <caiqian@redhat.com> pointed out that the semantics
of shared subtrees make it possible to create an exponentially
increasing number of mounts in a mount namespace.

    mkdir /tmp/1 /tmp/2
    mount --make-rshared /
    for i in $(seq 1 20) ; do mount --bind /tmp/1 /tmp/2 ; done

Will create create 2^20 or 1048576 mounts, which is a practical problem
as some people have managed to hit this by accident.

As such CVE-2016-6213 was assigned.

Ian Kent <raven@themaw.net> described the situation for autofs users
as follows:

> The number of mounts for direct mount maps is usually not very large because of
> the way they are implemented, large direct mount maps can have performance
> problems. There can be anywhere from a few (likely case a few hundred) to less
> than 10000, plus mounts that have been triggered and not yet expired.
>
> Indirect mounts have one autofs mount at the root plus the number of mounts that
> have been triggered and not yet expired.
>
> The number of autofs indirect map entries can range from a few to the common
> case of several thousand and in rare cases up to between 30000 and 50000. I've
> not heard of people with maps larger than 50000 entries.
>
> The larger the number of map entries the greater the possibility for a large
> number of active mounts so it's not hard to expect cases of a 1000 or somewhat
> more active mounts.

So I am setting the default number of mounts allowed per mount
namespace at 100,000.  This is more than enough for any use case I
know of, but small enough to quickly stop an exponential increase
in mounts.  Which should be perfect to catch misconfigurations and
malfunctioning programs.

For anyone who needs a higher limit this can be changed by writing
to the new /proc/sys/fs/mount-max sysctl.
Tested-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>

Conflicts:
	fs/namespace.c
	kernel/sysctl.c
Signed-off-by: Philipp Hahn <hahn@univention.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 07393101 ]

When file permissions are modified via chmod(2) and the user is not in
the owning group or capable of CAP_FSETID, the setgid bit is cleared in
inode_change_ok().  Setting a POSIX ACL via setxattr(2) sets the file
permissions as well as the new ACL, but doesn't clear the setgid bit in
a similar way; this allows to bypass the check in chmod(2).  Fix that.

References: CVE-2016-7097
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Philipp Hahn <hahn@univention.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 030b533c ]

Currently, notify_change() clears capabilities or IMA attributes by
calling security_inode_killpriv() before calling into ->setattr. Thus it
happens before any other permission checks in inode_change_ok() and user
is thus allowed to trigger clearing of capabilities or IMA attributes
for any file he can look up e.g. by calling chown for that file. This is
unexpected and can lead to user DoSing a system.

Fix the problem by calling security_inode_killpriv() at the end of
inode_change_ok() instead of from notify_change(). At that moment we are
sure user has permissions to do the requested change.

References: CVE-2015-1350
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Philipp Hahn <hahn@univention.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 31051c85 ]

inode_change_ok() will be resposible for clearing capabilities and IMA
extended attributes and as such will need dentry. Give it as an argument
to inode_change_ok() instead of an inode. Also rename inode_change_ok()
to setattr_prepare() to better relect that it does also some
modifications in addition to checks.

References: CVE-2015-1350
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Philipp Hahn <hahn@univention.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

NFSv2 can set the atime and/or mtime of a file to specific timestamps but not
to the server's current time.  To implement the equivalent of utimes("file",
NULL), it uses a heuristic.

NFSv3 and later do support setting the atime and/or mtime to the server's
current time directly.  The NFSv2 heuristic is still enabled, and causes
timestamps to be set wrong sometimes.

Fix this by moving the heuristic into the NFSv2 specific code.  We can leave it
out of the create code path: the owner can always set timestamps arbitrarily,
and the workaround would never trigger.

References: CVE-2015-1350
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Philipp Hahn <hahn@univention.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 62490330 ]

To avoid clearing of capabilities or security related extended
attributes too early, inode_change_ok() will need to take dentry instead
of inode. Propagate it down to fuse_do_setattr().

References: CVE-2015-1350
Acked-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>

Conflicts: Missing file_dentry() from d101a125Signed-off-by: Philipp Hahn <hahn@univention.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ upstream commit 69bca807 ]

To avoid clearing of capabilities or security related extended
attributes too early, inode_change_ok() will need to take dentry instead
of inode. Propagate dentry down to functions calling inode_change_ok().
This is rather straightforward except for xfs_set_mode() function which
does not have dentry easily available. Luckily that function does not
call inode_change_ok() anyway so we just have to do a little dance with
function prototypes.

References: CVE-2015-1350
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>

Conflicts: Missing file_dentry() from d101a125Signed-off-by: Philipp Hahn <hahn@univention.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

mbcache provides absolutely no value for Lustre xattrs (because
they are unique and cannot be shared between files) and as we can
see it has a noticable overhead in some cases. In the past there
was a CONFIG_MBCACHE option that would allow it to be disabled,
but this was removed in newer kernels, so we will need to patch
ldiskfs to fix this.

References: <https://bugzilla.kernel.org/show_bug.cgi?id=107301>
References: <https://git.hpdd.intel.com/fs/lustre-release.git/blob_plain/HEAD:/ldiskfs/kernel_patches/patches/rhel7/ext4-disable-mb-cache.patch>
References: CVE-2015-8952

On 13.12.2016 at 15:58 Ben Hutchings wrote:
> I decided not to apply this as it's a userland ABI extension that we
> would then need to carry indefinitely.
Signed-off-by: Philipp Hahn <hahn@univention.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>