- 21 Apr, 2017 5 commits
-
-
Kirill A. Shutemov authored
commit 58ceeb6b upstream. Both MADV_DONTNEED and MADV_FREE handled with down_read(mmap_sem). It's critical to not clear pmd intermittently while handling MADV_FREE to avoid race with MADV_DONTNEED: CPU0: CPU1: madvise_free_huge_pmd() pmdp_huge_get_and_clear_full() madvise_dontneed() zap_pmd_range() pmd_trans_huge(*pmd) == 0 (without ptl) // skip the pmd set_pmd_at(); // pmd is re-established It results in MADV_DONTNEED skipping the pmd, leaving it not cleared. It violates MADV_DONTNEED interface and can result is userspace misbehaviour. Basically it's the same race as with numa balancing in change_huge_pmd(), but a bit simpler to mitigate: we don't need to preserve dirty/young flags here due to MADV_FREE functionality. [kirill.shutemov@linux.intel.com: Urgh... Power is special again] Link: http://lkml.kernel.org/r/20170303102636.bhd2zhtpds4mt62a@black.fi.intel.com Link: http://lkml.kernel.org/r/20170302151034.27829-4-kirill.shutemov@linux.intel.comSigned-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by:
Minchan Kim <minchan@kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hillf Danton <hillf.zj@alibaba-inc.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Xiubo Li authored
commit a5d68ba8 upstream. For the bidirectional case, the Data-Out buffer blocks will always at the head of the tcmu_cmd's bitmap, and before gathering the Data-In buffer, first of all it should skip the Data-Out ones, or the device supporting BIDI commands won't work. Fixed: 26418649 ("target/user: Introduce data_bitmap, replace data_length/data_head/data_tail") Reported-by:
Ilias Tsitsimpis <iliastsi@arrikto.com> Tested-by:
Xiubo Li <lixiubo@cmss.chinamobile.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Xiubo Li authored
commit abe342a5 upstream. The t_data_nents and t_bidi_data_nents are the numbers of the segments, but it couldn't be sure the block size equals to size of the segment. For the worst case, all the blocks are discontiguous and there will need the same number of iovecs, that's to say: blocks == iovs. So here just set the number of iovs to block count needed by tcmu cmd. Tested-by:
Mike Christie <mchristi@redhat.com> Signed-off-by:
-
Xiubo Li authored
commit ab22d260 upstream. If there has BIDI data, its first iov[] will overwrite the last iov[] for se_cmd->t_data_sg. To fix this, we can just increase the iov pointer, but this may introuduce a new memory leakage bug: If the se_cmd->data_length and se_cmd->t_bidi_data_sg->length are all not aligned up to the DATA_BLOCK_SIZE, the actual length needed maybe larger than just sum of them. So, this could be avoided by rounding all the data lengthes up to DATA_BLOCK_SIZE. Reviewed-by:
Bryant G. Ly <bryantly@linux.vnet.ibm.com> Signed-off-by:
-
Tejun Heo authored
commit 77f88796 upstream. Creation of a kthread goes through a couple interlocked stages between the kthread itself and its creator. Once the new kthread starts running, it initializes itself and wakes up the creator. The creator then can further configure the kthread and then let it start doing its job by waking it up. In this configuration-by-creator stage, the creator is the only one that can wake it up but the kthread is visible to userland. When altering the kthread's attributes from userland is allowed, this is fine; however, for cases where CPU affinity is critical, kthread_bind() is used to first disable affinity changes from userland and then set the affinity. This also prevents the kthread from being migrated into non-root cgroups as that can affect the CPU affinity and many other things. Unfortunately, the cgroup side of protection is racy. While the PF_NO_SETAFFINITY flag prevents further migrations, userland can win the race before the creator sets the flag with kthread_bind() and put the kthread in a non-root cgroup, which can lead to all sorts of problems including incorrect CPU affinity and starvation. This bug got triggered by userland which periodically tries to migrate all processes in the root cpuset cgroup to a non-root one. Per-cpu workqueue workers got caught while being created and ended up with incorrected CPU affinity breaking concurrency management and sometimes stalling workqueue execution. This patch adds task->no_cgroup_migration which disallows the task to be migrated by userland. kthreadd starts with the flag set making every child kthread start in the root cgroup with migration disallowed. The flag is cleared after the kthread finishes initialization by which time PF_NO_SETAFFINITY is set if the kthread should stay in the root cgroup. It'd be better to wait for the initialization instead of failing but I couldn't think of a way of implementing that without adding either a new PF flag, or sleeping and retrying from waiting side. Even if userland depends on changing cgroup membership of a kthread, it either has to be synchronized with kthread_create() or periodically repeat, so it's unlikely that this would break anything. v2: Switch to a simpler implementation using a new task_struct bit field suggested by Oleg. Signed-off-by:
Tejun Heo <tj@kernel.org> Suggested-by:
Oleg Nesterov <oleg@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Reported-and-debugged-by:
Chris Mason <clm@fb.com> Signed-off-by:
-
- 18 Apr, 2017 32 commits
-
-
Greg Kroah-Hartman authored
-
Marek Szyprowski authored
commit 888022c0 upstream. Add compat ioctl support to dma-buf. This lets one to use DMA_BUF_IOCTL_SYNC ioctl from 32bit application on 64bit kernel. Data structures for both 32 and 64bit modes are same, so there is no need for additional translation layer. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Acked-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Sumit Semwal <sumit.semwal@linaro.org> Link: http://patchwork.freedesktop.org/patch/msgid/1487683261-2655-1-git-send-email-m.szyprowski@samsung.comSigned-off-by:
-
Jack Morgenstein authored
commit 7c3945bc upstream. Save the qp context flags byte containing the flag disabling vlan stripping in the RESET to INIT qp transition, rather than in the INIT to RTR transition. Per the firmware spec, the flags in this byte are active in the RESET to INIT transition. As a result of saving the flags in the incorrect qp transition, when switching dynamically from VGT to VST and back to VGT, the vlan remained stripped (as is required for VST) and did not return to not-stripped (as is required for VGT). Fixes: f0f829bf ("net/mlx4_core: Add immediate activate for VGT->VST->VGT") Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Jack Morgenstein authored
commit 291c566a upstream. In function mlx4_cq_completion() and mlx4_cq_event(), the radix_tree_lookup requires a rcu_read_lock. This is mandatory: if another core frees the CQ, it could run the radix_tree_node_rcu_free() call_rcu() callback while its being used by the radix tree lookup function. Additionally, in function mlx4_cq_event(), since we are adding the rcu lock around the radix-tree lookup, we no longer need to take the spinlock. Also, the synchronize_irq() call for the async event eliminates the need for incrementing the cq reference count in mlx4_cq_event(). Other changes: 1. In function mlx4_cq_free(), replace spin_lock_irq with spin_lock: we no longer take this spinlock in the interrupt context. The spinlock here, therefore, simply protects against different threads simultaneously invoking mlx4_cq_free() for different cq's. 2. In function mlx4_cq_free(), we move the radix tree delete to before the synchronize_irq() calls. This guarantees that we will not access this cq during any subsequent interrupts, and therefore can safely free the CQ after the synchronize_irq calls. The rcu_read_lock in the interrupt handlers only needs to protect against corrupting the radix tree; the interrupt handlers may access the cq outside the rcu_read_lock due to the synchronize_irq calls which protect against premature freeing of the cq. 3. In function mlx4_cq_event(), we change the mlx_warn message to mlx4_dbg. 4. We leave the cq reference count mechanism in place, because it is still needed for the cq completion tasklet mechanism. Fixes: 6d90aa5c ("net/mlx4_core: Make sure there are no pending async events when freeing CQ") Fixes: 225c7b1f ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters") Signed-off-by:
Matan Barak <matanb@mellanox.com> Signed-off-by:
-
Eugenia Emantayev authored
commit 6496bbf0 upstream. Single send WQE in RX buffer should be stamped with software ownership in order to prevent the flow of QP in error in FW once UPDATE_QP is called. Fixes: 9f519f68 ('mlx4_en: Not using Shared Receive Queues') Signed-off-by:
Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by:
-
Guenter Roeck authored
commit 22547c4c upstream. On a system with a defective USB device connected to an USB hub, an endless sequence of port connect events was observed. The sequence of events as observed is as follows: - Port reports connected event (port status=USB_PORT_STAT_CONNECTION). - Event handler debounces port and resets it by calling hub_port_reset(). - hub_port_reset() calls hub_port_wait_reset() to wait for the reset to complete. - The reset completes, but USB_PORT_STAT_CONNECTION is not immediately set in the port status register. - hub_port_wait_reset() returns -ENOTCONN. - Port initialization sequence is aborted. - A few milliseconds later, the port again reports a connected event, and the sequence repeats. This continues either forever or, randomly, stops if the connection is already re-established when the port status is read. It results in a high rate of udev events. This in turn destabilizes userspace since the above sequence holds the device mutex pretty much continuously and prevents userspace from actually reading the device status. To prevent the problem from happening, let's wait for the connection to be re-established after a port reset. If the device was actually disconnected, the code will still return an error, but it will do so only after the long reset timeout. Cc: Douglas Anderson <dianders@chromium.org> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Gabriel Krisman Bertazi authored
commit 36e1f3d1 upstream. While stressing memory and IO at the same time we changed SMT settings, we were able to consistently trigger deadlocks in the mm system, which froze the entire machine. I think that under memory stress conditions, the large allocations performed by blk_mq_init_rq_map may trigger a reclaim, which stalls waiting on the block layer remmaping completion, thus deadlocking the system. The trace below was collected after the machine stalled, waiting for the hotplug event completion. The simplest fix for this is to make allocations in this path non-reclaimable, with GFP_NOIO. With this patch, We couldn't hit the issue anymore. This should apply on top of Jens's for-next branch cleanly. Changes since v1: - Use GFP_NOIO instead of GFP_NOWAIT. Call Trace: [c000000f0160aaf0] [c000000f0160ab50] 0xc000000f0160ab50 (unreliable) [c000000f0160acc0] [c000000000016624] __switch_to+0x2e4/0x430 [c000000f0160ad20] [c000000000b1a880] __schedule+0x310/0x9b0 [c000000f0160ae00] [c000000000b1af68] schedule+0x48/0xc0 [c000000f0160ae30] [c000000000b1b4b0] schedule_preempt_disabled+0x20/0x30 [c000000f0160ae50] [c000000000b1d4fc] __mutex_lock_slowpath+0xec/0x1f0 [c000000f0160aed0] [c000000000b1d678] mutex_lock+0x78/0xa0 [c000000f0160af00] [d000000019413cac] xfs_reclaim_inodes_ag+0x33c/0x380 [xfs] [c000000f0160b0b0] [d000000019415164] xfs_reclaim_inodes_nr+0x54/0x70 [xfs] [c000000f0160b0f0] [d0000000194297f8] xfs_fs_free_cached_objects+0x38/0x60 [xfs] [c000000f0160b120] [c0000000003172c8] super_cache_scan+0x1f8/0x210 [c000000f0160b190] [c00000000026301c] shrink_slab.part.13+0x21c/0x4c0 [c000000f0160b2d0] [c000000000268088] shrink_zone+0x2d8/0x3c0 [c000000f0160b380] [c00000000026834c] do_try_to_free_pages+0x1dc/0x520 [c000000f0160b450] [c00000000026876c] try_to_free_pages+0xdc/0x250 [c000000f0160b4e0] [c000000000251978] __alloc_pages_nodemask+0x868/0x10d0 [c000000f0160b6f0] [c000000000567030] blk_mq_init_rq_map+0x160/0x380 [c000000f0160b7a0] [c00000000056758c] blk_mq_map_swqueue+0x33c/0x360 [c000000f0160b820] [c000000000567904] blk_mq_queue_reinit+0x64/0xb0 [c000000f0160b850] [c00000000056a16c] blk_mq_queue_reinit_notify+0x19c/0x250 [c000000f0160b8a0] [c0000000000f5d38] notifier_call_chain+0x98/0x100 [c000000f0160b8f0] [c0000000000c5fb0] __cpu_notify+0x70/0xe0 [c000000f0160b930] [c0000000000c63c4] notify_prepare+0x44/0xb0 [c000000f0160b9b0] [c0000000000c52f4] cpuhp_invoke_callback+0x84/0x250 [c000000f0160ba10] [c0000000000c570c] cpuhp_up_callbacks+0x5c/0x120 [c000000f0160ba60] [c0000000000c7cb8] _cpu_up+0xf8/0x1d0 [c000000f0160bac0] [c0000000000c7eb0] do_cpu_up+0x120/0x150 [c000000f0160bb40] [c0000000006fe024] cpu_subsys_online+0x64/0xe0 [c000000f0160bb90] [c0000000006f5124] device_online+0xb4/0x120 [c000000f0160bbd0] [c0000000006f5244] online_store+0xb4/0xc0 [c000000f0160bc20] [c0000000006f0a68] dev_attr_store+0x68/0xa0 [c000000f0160bc60] [c0000000003ccc30] sysfs_kf_write+0x80/0xb0 [c000000f0160bca0] [c0000000003cbabc] kernfs_fop_write+0x17c/0x250 [c000000f0160bcf0] [c00000000030fe6c] __vfs_write+0x6c/0x1e0 [c000000f0160bd90] [c000000000311490] vfs_write+0xd0/0x270 [c000000f0160bde0] [c0000000003131fc] SyS_write+0x6c/0x110 [c000000f0160be30] [c000000000009204] system_call+0x38/0xec Signed-off-by:
Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Cc: Brian King <brking@linux.vnet.ibm.com> Cc: Douglas Miller <dougmill@linux.vnet.ibm.com> Cc: linux-block@vger.kernel.org Cc: linux-scsi@vger.kernel.org Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Andrey Konovalov authored
commit 2b6867c2 upstream. Subtracting tp_sizeof_priv from tp_block_size and casting to int to check whether one is less then the other doesn't always work (both of them are unsigned ints). Compare them as is instead. Also cast tp_sizeof_priv to u64 before using BLK_PLUS_PRIV, as it can overflow inside BLK_PLUS_PRIV otherwise. Signed-off-by:
Andrey Konovalov <andreyknvl@google.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Greg Kroah-Hartman authored
This reverts commit f2a0409a which is commit bafb2f7d upstream. It was reported to have problems. Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Eric Blau <eblau1@gmail.com> Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
-
Horia Geantă authored
commit 33fa46d7 upstream. In case caam_jr_alloc() fails, ctx->dev carries the error code, thus accessing it with dev_err() is incorrect. Fixes: 8c419778 ("crypto: caam - add support for RSA algorithm") Signed-off-by:
Horia Geantă <horia.geanta@nxp.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Horia Geantă authored
commit 40c98cb5 upstream. RNG instantiation was previously fixed by commit 62743a41 ("crypto: caam - fix RNG init descriptor ret. code checking") while deinstantiation was not addressed. Since the descriptors used are similar, in the sense that they both end with a JUMP HALT command, checking for errors should be similar too, i.e. status code 7000_0000h should be considered successful. Fixes: 1005bccd ("crypto: caam - enable instantiation of all RNG4 state handles") Signed-off-by:
-
Matt Redfearn authored
commit c25f8064 upstream. Commit dda45f70 ("MIPS: Switch to the irq_stack in interrupts") changed both the normal and vectored interrupt handlers. Unfortunately the vectored version, "except_vec_vi_handler", was incorrectly modified to unconditionally jal to plat_irq_dispatch, rather than doing a jalr to the vectored handler that has been set up. This is ok for many platforms which set the vectored handler to plat_irq_dispatch anyway, but will cause problems with platforms that use other handlers. Fixes: dda45f70 ("MIPS: Switch to the irq_stack in interrupts") Signed-off-by:
Matt Redfearn <matt.redfearn@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/15110/Signed-off-by:
James Hogan <james.hogan@imgtec.com> Signed-off-by:
Amit Pundir <amit.pundir@linaro.org> Signed-off-by:
-
Matt Redfearn authored
commit 3cc3434f upstream. Since do_IRQ is now invoked on a separate IRQ stack, we select HAVE_IRQ_EXIT_ON_IRQ_STACK so that softirq's may be invoked directly from irq_exit(), rather than requiring do_softirq_own_stack. Signed-off-by:
Jason A. Donenfeld <jason@zx2c4.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/14744/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Matt Redfearn authored
commit dda45f70 upstream. When enterring interrupt context via handle_int or except_vec_vi, switch to the irq_stack of the current CPU if it is not already in use. The current stack pointer is masked with the thread size and compared to the base or the irq stack. If it does not match then the stack pointer is set to the top of that stack, otherwise this is a nested irq being handled on the irq stack so the stack pointer should be left as it was. The in-use stack pointer is placed in the callee saved register s1. It will be saved to the stack when plat_irq_dispatch is invoked and can be restored once control returns here. Signed-off-by:
-
Matt Redfearn authored
commit 510d8636 upstream. The SAVE_SOME macro is used to save the execution context on all exceptions. If an exception occurs while executing user code, the stack is switched to the kernel's stack for the current task, and register $28 is switched to point to the current_thread_info, which is at the bottom of the stack region. If the exception occurs while executing kernel code, the stack is left, and this change ensures that register $28 is not updated. This is the correct behaviour when the kernel can be executing on the separate irq stack, because the thread_info will not be at the base of it. With this change, register $28 is only switched to it's kernel conventional usage of the currrent thread info pointer at the point at which execution enters kernel space. Doing it on every exception was redundant, but OK without an IRQ stack, but will be erroneous once that is introduced. Signed-off-by:
-
Matt Redfearn authored
commit d42d8d10 upstream. Within unwind stack, check if the stack pointer being unwound is within the CPU's irq_stack and if so use that page rather than the task's stack page. Signed-off-by:
-
Matt Redfearn authored
commit fe8bd18f upstream. Allocate a per-cpu irq stack for use within interrupt handlers. Also add a utility function on_irq_stack to determine if a given stack pointer is within the irq stack for that cpu. Signed-off-by:
-
Rafał Miłecki authored
commit bd5d2131 upstream. After parsing TRX we should skip to the first block placed behind it. Our code was working only with TRX with length not aligned to the blocksize. In other cases (length aligned) it was missing the block places right after TRX. This fixes calculation and simplifies the comment. Signed-off-by:
Rafał Miłecki <rafal@milecki.pl> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Vishal Thanki authored
commit a083c8fd upstream. In device removal routine, usage of "#ifdef CONFIG_RT2X00_LIB_USB" will not cover the case when it is configured as module. This will omit the entire if-block which does cleanup of URBs and cancellation of pending work. Changing the #ifdef to #if IS_ENABLED() to fix it. Signed-off-by:
Vishal Thanki <vishalthanki@gmail.com> Acked-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Stanislaw Gruszka authored
commit 93c7018e upstream. We might kill TX or RX urb during rt2x00usb_flush_entry(), what can cause anchor list corruption like shown below: [ 2074.035633] WARNING: CPU: 2 PID: 14480 at lib/list_debug.c:33 __list_add+0xac/0xc0 [ 2074.035634] list_add corruption. prev->next should be next (ffff88020f362c28), but was dead000000000100. (prev=ffff8801d161bb70). <snip> [ 2074.035670] Call Trace: [ 2074.035672] [<ffffffff813bde47>] dump_stack+0x63/0x8c [ 2074.035674] [<ffffffff810a2231>] __warn+0xd1/0xf0 [ 2074.035676] [<ffffffff810a22af>] warn_slowpath_fmt+0x5f/0x80 [ 2074.035678] [<ffffffffa073855d>] ? rt2x00usb_register_write_lock+0x3d/0x60 [rt2800usb] [ 2074.035679] [<ffffffff813dbe4c>] __list_add+0xac/0xc0 [ 2074.035681] [<ffffffff81591c6c>] usb_anchor_urb+0x4c/0xa0 [ 2074.035683] [<ffffffffa07322af>] rt2x00usb_kick_rx_entry+0xaf/0x100 [rt2x00usb] [ 2074.035684] [<ffffffffa0732322>] rt2x00usb_clear_entry+0x22/0x30 [rt2x00usb] To fix do not anchor TX and RX urb's, it is not needed as during shutdown we kill those urbs in rt2x00usb_free_entries(). Cc: Vishal Thanki <vishalthanki@gmail.com> Fixes: 8b4c0009 ("rt2x00usb: Use usb anchor to manage URB") Signed-off-by:
-
Stanislaw Gruszka authored
commit 0488a612 upstream. If device fail to initialize we can OOPS in rt2x00lib_remove_dev(), due to using uninitialized usb_anchor structure: [ 855.435820] ieee80211 phy3: rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x1000 with error -19 [ 855.435826] ieee80211 phy3: rt2800_probe_rt: Error - Invalid RT chipset 0x0000, rev 0000 detected [ 855.435829] ieee80211 phy3: rt2x00lib_probe_dev: Error - Failed to allocate device [ 855.435845] BUG: unable to handle kernel NULL pointer dereference at 0000000000000028 [ 855.435900] IP: _raw_spin_lock_irq+0xd/0x30 [ 855.435926] PGD 0 [ 855.435953] Oops: 0002 [#1] SMP <snip> [ 855.437011] Call Trace: [ 855.437029] ? usb_kill_anchored_urbs+0x27/0xc0 [ 855.437061] rt2x00lib_remove_dev+0x190/0x1c0 [rt2x00lib] [ 855.437097] rt2x00lib_probe_dev+0x246/0x7a0 [rt2x00lib] [ 855.437149] ? ieee80211_roc_setup+0x9e/0xd0 [mac80211] [ 855.437183] ? __kmalloc+0x1af/0x1f0 [ 855.437207] ? rt2x00usb_probe+0x13d/0xc50 [rt2x00usb] [ 855.437240] rt2x00usb_probe+0x155/0xc50 [rt2x00usb] [ 855.437273] rt2800usb_probe+0x15/0x20 [rt2800usb] [ 855.437304] usb_probe_interface+0x159/0x2d0 [ 855.437333] driver_probe_device+0x2bb/0x460 Patch changes initialization sequence to fix the problem. Cc: Vishal Thanki <vishalthanki@gmail.com> Fixes: 8b4c0009 ("rt2x00usb: Use usb anchor to manage URB") Signed-off-by:
-
Noralf Trønnes authored
commit e2474541 upstream. Writing messages larger than the FIFO size results in a hang, rendering the machine unusable. This is because the RXD status flag is set on the first interrupt which results in bcm2835_drain_rxfifo() stealing bytes from the buffer. The controller continues to trigger interrupts waiting for the missing bytes, but bcm2835_fill_txfifo() has none to give. In this situation wait_for_completion_timeout() apparently is unable to stop the madness. The BCM2835 ARM Peripherals datasheet has this to say about the flags: TXD: is set when the FIFO has space for at least one byte of data. RXD: is set when the FIFO contains at least one byte of data. TXW: is set during a write transfer and the FIFO is less than full. RXR: is set during a read transfer and the FIFO is or more full. Implementing the logic from the downstream i2c-bcm2708 driver solved the hang problem. Signed-off-by:
Noralf Trønnes <noralf@tronnes.org> Reviewed-by:
Eric Anholt <eric@anholt.net> Reviewed-by:
Martin Sperl <kernel@martin.sperl.org> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Mike Marshall authored
commit eb68d032 upstream. The deamon through which the kernel module communicates with the userspace part of Orangefs, the "client-core", sends initialization data to the kernel module with ioctl. The initialization data was built by the client-core in a 2k buffer and copy_from_user'd into a 1k buffer in the kernel module. When more than 1k of initialization data needed to be sent, some was lost, reducing the usability of the control by which debug levels are set. This patch sets the kernel side buffer to 2K to match the userspace side... Signed-off-by:
Mike Marshall <hubcap@omnibond.com> Signed-off-by:
Martin Brandenburg <martin@omnibond.com> Signed-off-by:
-
Mike Marshall authored
commit 05973c2e upstream. This patch is simlar to one Dan Carpenter sent me, cleans up some return codes and whitespace errors. There was one place where he thought inserting an error message into the ring buffer might be too chatty, I hope I convinced him othewise. As a consolation <g> I changed a truly chatty error message in another location into a debug message, system-admins had already yelled at me about that one... Signed-off-by:
-
Colin Ian King authored
commit 4defb5f9 upstream. allocates string 'new' is not free'd on the exit path when cdm_element_count <= 0. Fix this by kfree'ing it. Fixes CoverityScan CID#1375923 "Resource Leak" Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Chris Wilson authored
commit 3d3d18f0 upstream. The rcu_barrier() takes the cpu_hotplug mutex which itself is not reclaim-safe, and so rcu_barrier() is illegal from inside the shrinker. [ 309.661373] ========================================================= [ 309.661376] [ INFO: possible irq lock inversion dependency detected ] [ 309.661380] 4.11.0-rc1-CI-CI_DRM_2333+ #1 Tainted: G W [ 309.661383] --------------------------------------------------------- [ 309.661386] gem_exec_gttfil/6435 just changed the state of lock: [ 309.661389] (rcu_preempt_state.barrier_mutex){+.+.-.}, at: [<ffffffff81100731>] _rcu_barrier+0x31/0x160 [ 309.661399] but this lock took another, RECLAIM_FS-unsafe lock in the past: [ 309.661402] (cpu_hotplug.lock){+.+.+.} [ 309.661404] and interrupts could create inverse lock ordering between them. [ 309.661410] other info that might help us debug this: [ 309.661414] Possible interrupt unsafe locking scenario: [ 309.661417] CPU0 CPU1 [ 309.661419] ---- ---- [ 309.661421] lock(cpu_hotplug.lock); [ 309.661425] local_irq_disable(); [ 309.661432] lock(rcu_preempt_state.barrier_mutex); [ 309.661441] lock(cpu_hotplug.lock); [ 309.661446] <Interrupt> [ 309.661448] lock(rcu_preempt_state.barrier_mutex); [ 309.661453] *** DEADLOCK *** [ 309.661460] 4 locks held by gem_exec_gttfil/6435: [ 309.661464] #0: (sb_writers#10){.+.+.+}, at: [<ffffffff8120d83d>] vfs_write+0x17d/0x1f0 [ 309.661475] #1: (debugfs_srcu){......}, at: [<ffffffff81320491>] debugfs_use_file_start+0x41/0xa0 [ 309.661486] #2: (&attr->mutex){+.+.+.}, at: [<ffffffff8123a3e7>] simple_attr_write+0x37/0xe0 [ 309.661495] #3: (&dev->struct_mutex){+.+.+.}, at: [<ffffffffa0091b4a>] i915_drop_caches_set+0x3a/0x150 [i915] [ 309.661540] the shortest dependencies between 2nd lock and 1st lock: [ 309.661547] -> (cpu_hotplug.lock){+.+.+.} ops: 829 { [ 309.661553] HARDIRQ-ON-W at: [ 309.661560] __lock_acquire+0x5e5/0x1b50 [ 309.661565] lock_acquire+0xc9/0x220 [ 309.661572] __mutex_lock+0x6e/0x990 [ 309.661576] mutex_lock_nested+0x16/0x20 [ 309.661583] get_online_cpus+0x61/0x80 [ 309.661590] kmem_cache_create+0x25/0x1d0 [ 309.661596] debug_objects_mem_init+0x30/0x249 [ 309.661602] start_kernel+0x341/0x3fe [ 309.661607] x86_64_start_reservations+0x2a/0x2c [ 309.661612] x86_64_start_kernel+0x173/0x186 [ 309.661619] verify_cpu+0x0/0xfc [ 309.661622] SOFTIRQ-ON-W at: [ 309.661627] __lock_acquire+0x611/0x1b50 [ 309.661632] lock_acquire+0xc9/0x220 [ 309.661636] __mutex_lock+0x6e/0x990 [ 309.661641] mutex_lock_nested+0x16/0x20 [ 309.661646] get_online_cpus+0x61/0x80 [ 309.661650] kmem_cache_create+0x25/0x1d0 [ 309.661655] debug_objects_mem_init+0x30/0x249 [ 309.661660] start_kernel+0x341/0x3fe [ 309.661664] x86_64_start_reservations+0x2a/0x2c [ 309.661669] x86_64_start_kernel+0x173/0x186 [ 309.661674] verify_cpu+0x0/0xfc [ 309.661677] RECLAIM_FS-ON-W at: [ 309.661682] mark_held_locks+0x6f/0xa0 [ 309.661687] lockdep_trace_alloc+0xb3/0x100 [ 309.661693] kmem_cache_alloc_trace+0x31/0x2e0 [ 309.661699] __smpboot_create_thread.part.1+0x27/0xe0 [ 309.661704] smpboot_create_threads+0x61/0x90 [ 309.661709] cpuhp_invoke_callback+0x9c/0x8a0 [ 309.661713] cpuhp_up_callbacks+0x31/0xb0 [ 309.661718] _cpu_up+0x7a/0xc0 [ 309.661723] do_cpu_up+0x5f/0x80 [ 309.661727] cpu_up+0xe/0x10 [ 309.661734] smp_init+0x71/0xb3 [ 309.661738] kernel_init_freeable+0x94/0x19e [ 309.661743] kernel_init+0x9/0xf0 [ 309.661748] ret_from_fork+0x2e/0x40 [ 309.661752] INITIAL USE at: [ 309.661757] __lock_acquire+0x234/0x1b50 [ 309.661761] lock_acquire+0xc9/0x220 [ 309.661766] __mutex_lock+0x6e/0x990 [ 309.661771] mutex_lock_nested+0x16/0x20 [ 309.661775] get_online_cpus+0x61/0x80 [ 309.661780] __cpuhp_setup_state+0x44/0x170 [ 309.661785] page_alloc_init+0x23/0x3a [ 309.661790] start_kernel+0x124/0x3fe [ 309.661794] x86_64_start_reservations+0x2a/0x2c [ 309.661799] x86_64_start_kernel+0x173/0x186 [ 309.661804] verify_cpu+0x0/0xfc [ 309.661807] } [ 309.661813] ... key at: [<ffffffff81e37690>] cpu_hotplug+0xb0/0x100 [ 309.661817] ... acquired at: [ 309.661821] lock_acquire+0xc9/0x220 [ 309.661825] __mutex_lock+0x6e/0x990 [ 309.661829] mutex_lock_nested+0x16/0x20 [ 309.661833] get_online_cpus+0x61/0x80 [ 309.661837] _rcu_barrier+0x9f/0x160 [ 309.661841] rcu_barrier+0x10/0x20 [ 309.661847] netdev_run_todo+0x5f/0x310 [ 309.661852] rtnl_unlock+0x9/0x10 [ 309.661856] default_device_exit_batch+0x133/0x150 [ 309.661862] ops_exit_list.isra.0+0x4d/0x60 [ 309.661866] cleanup_net+0x1d8/0x2c0 [ 309.661872] process_one_work+0x1f4/0x6d0 [ 309.661876] worker_thread+0x49/0x4a0 [ 309.661881] kthread+0x107/0x140 [ 309.661884] ret_from_fork+0x2e/0x40 [ 309.661890] -> (rcu_preempt_state.barrier_mutex){+.+.-.} ops: 179 { [ 309.661896] HARDIRQ-ON-W at: [ 309.661901] __lock_acquire+0x5e5/0x1b50 [ 309.661905] lock_acquire+0xc9/0x220 [ 309.661910] __mutex_lock+0x6e/0x990 [ 309.661914] mutex_lock_nested+0x16/0x20 [ 309.661919] _rcu_barrier+0x31/0x160 [ 309.661923] rcu_barrier+0x10/0x20 [ 309.661928] netdev_run_todo+0x5f/0x310 [ 309.661932] rtnl_unlock+0x9/0x10 [ 309.661936] default_device_exit_batch+0x133/0x150 [ 309.661941] ops_exit_list.isra.0+0x4d/0x60 [ 309.661946] cleanup_net+0x1d8/0x2c0 [ 309.661951] process_one_work+0x1f4/0x6d0 [ 309.661955] worker_thread+0x49/0x4a0 [ 309.661960] kthread+0x107/0x140 [ 309.661964] ret_from_fork+0x2e/0x40 [ 309.661968] SOFTIRQ-ON-W at: [ 309.661972] __lock_acquire+0x611/0x1b50 [ 309.661977] lock_acquire+0xc9/0x220 [ 309.661981] __mutex_lock+0x6e/0x990 [ 309.661986] mutex_lock_nested+0x16/0x20 [ 309.661990] _rcu_barrier+0x31/0x160 [ 309.661995] rcu_barrier+0x10/0x20 [ 309.661999] netdev_run_todo+0x5f/0x310 [ 309.662003] rtnl_unlock+0x9/0x10 [ 309.662008] default_device_exit_batch+0x133/0x150 [ 309.662013] ops_exit_list.isra.0+0x4d/0x60 [ 309.662017] cleanup_net+0x1d8/0x2c0 [ 309.662022] process_one_work+0x1f4/0x6d0 [ 309.662027] worker_thread+0x49/0x4a0 [ 309.662031] kthread+0x107/0x140 [ 309.662035] ret_from_fork+0x2e/0x40 [ 309.662039] IN-RECLAIM_FS-W at: [ 309.662043] __lock_acquire+0x638/0x1b50 [ 309.662048] lock_acquire+0xc9/0x220 [ 309.662053] __mutex_lock+0x6e/0x990 [ 309.662058] mutex_lock_nested+0x16/0x20 [ 309.662062] _rcu_barrier+0x31/0x160 [ 309.662067] rcu_barrier+0x10/0x20 [ 309.662089] i915_gem_shrink_all+0x33/0x40 [i915] [ 309.662109] i915_drop_caches_set+0x141/0x150 [i915] [ 309.662114] simple_attr_write+0xc7/0xe0 [ 309.662119] full_proxy_write+0x4f/0x70 [ 309.662124] __vfs_write+0x23/0x120 [ 309.662128] vfs_write+0xc6/0x1f0 [ 309.662133] SyS_write+0x44/0xb0 [ 309.662138] entry_SYSCALL_64_fastpath+0x1c/0xb1 [ 309.662142] INITIAL USE at: [ 309.662147] __lock_acquire+0x234/0x1b50 [ 309.662151] lock_acquire+0xc9/0x220 [ 309.662156] __mutex_lock+0x6e/0x990 [ 309.662160] mutex_lock_nested+0x16/0x20 [ 309.662165] _rcu_barrier+0x31/0x160 [ 309.662169] rcu_barrier+0x10/0x20 [ 309.662174] netdev_run_todo+0x5f/0x310 [ 309.662178] rtnl_unlock+0x9/0x10 [ 309.662183] default_device_exit_batch+0x133/0x150 [ 309.662188] ops_exit_list.isra.0+0x4d/0x60 [ 309.662192] cleanup_net+0x1d8/0x2c0 [ 309.662197] process_one_work+0x1f4/0x6d0 [ 309.662202] worker_thread+0x49/0x4a0 [ 309.662206] kthread+0x107/0x140 [ 309.662210] ret_from_fork+0x2e/0x40 [ 309.662214] } [ 309.662220] ... key at: [<ffffffff81e4e1c8>] rcu_preempt_state+0x508/0x780 [ 309.662225] ... acquired at: [ 309.662229] check_usage_forwards+0x12b/0x130 [ 309.662233] mark_lock+0x360/0x6f0 [ 309.662237] __lock_acquire+0x638/0x1b50 [ 309.662241] lock_acquire+0xc9/0x220 [ 309.662245] __mutex_lock+0x6e/0x990 [ 309.662249] mutex_lock_nested+0x16/0x20 [ 309.662253] _rcu_barrier+0x31/0x160 [ 309.662257] rcu_barrier+0x10/0x20 [ 309.662279] i915_gem_shrink_all+0x33/0x40 [i915] [ 309.662298] i915_drop_caches_set+0x141/0x150 [i915] [ 309.662303] simple_attr_write+0xc7/0xe0 [ 309.662307] full_proxy_write+0x4f/0x70 [ 309.662311] __vfs_write+0x23/0x120 [ 309.662315] vfs_write+0xc6/0x1f0 [ 309.662319] SyS_write+0x44/0xb0 [ 309.662323] entry_SYSCALL_64_fastpath+0x1c/0xb1 [ 309.662329] stack backtrace: [ 309.662335] CPU: 1 PID: 6435 Comm: gem_exec_gttfil Tainted: G W 4.11.0-rc1-CI-CI_DRM_2333+ #1 [ 309.662342] Hardware name: Hewlett-Packard HP Compaq 8100 Elite SFF PC/304Ah, BIOS 786H1 v01.13 07/14/2011 [ 309.662348] Call Trace: [ 309.662354] dump_stack+0x67/0x92 [ 309.662359] print_irq_inversion_bug.part.19+0x1a4/0x1b0 [ 309.662365] check_usage_forwards+0x12b/0x130 [ 309.662369] mark_lock+0x360/0x6f0 [ 309.662374] ? print_shortest_lock_dependencies+0x1a0/0x1a0 [ 309.662379] __lock_acquire+0x638/0x1b50 [ 309.662383] ? __mutex_unlock_slowpath+0x3e/0x2e0 [ 309.662388] ? trace_hardirqs_on+0xd/0x10 [ 309.662392] ? _rcu_barrier+0x31/0x160 [ 309.662396] lock_acquire+0xc9/0x220 [ 309.662400] ? _rcu_barrier+0x31/0x160 [ 309.662404] ? _rcu_barrier+0x31/0x160 [ 309.662409] __mutex_lock+0x6e/0x990 [ 309.662412] ? _rcu_barrier+0x31/0x160 [ 309.662416] ? _rcu_barrier+0x31/0x160 [ 309.662421] ? synchronize_rcu_expedited+0x35/0xb0 [ 309.662426] ? _raw_spin_unlock_irqrestore+0x52/0x60 [ 309.662434] mutex_lock_nested+0x16/0x20 [ 309.662438] _rcu_barrier+0x31/0x160 [ 309.662442] rcu_barrier+0x10/0x20 [ 309.662464] i915_gem_shrink_all+0x33/0x40 [i915] [ 309.662484] i915_drop_caches_set+0x141/0x150 [i915] [ 309.662489] simple_attr_write+0xc7/0xe0 [ 309.662494] full_proxy_write+0x4f/0x70 [ 309.662498] __vfs_write+0x23/0x120 [ 309.662503] ? rcu_read_lock_sched_held+0x75/0x80 [ 309.662507] ? rcu_sync_lockdep_assert+0x2a/0x50 [ 309.662512] ? __sb_start_write+0x102/0x210 [ 309.662516] ? vfs_write+0x17d/0x1f0 [ 309.662520] vfs_write+0xc6/0x1f0 [ 309.662524] ? trace_hardirqs_on_caller+0xe7/0x200 [ 309.662529] SyS_write+0x44/0xb0 [ 309.662533] entry_SYSCALL_64_fastpath+0x1c/0xb1 [ 309.662537] RIP: 0033:0x7f507eac24a0 [ 309.662541] RSP: 002b:00007fffda8720e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 309.662548] RAX: ffffffffffffffda RBX: ffffffff81482bd3 RCX: 00007f507eac24a0 [ 309.662552] RDX: 0000000000000005 RSI: 00007fffda8720f0 RDI: 0000000000000005 [ 309.662557] RBP: ffffc9000048bf88 R08: 0000000000000000 R09: 000000000000002c [ 309.662561] R10: 0000000000000014 R11: 0000000000000246 R12: 00007fffda872230 [ 309.662566] R13: 00007fffda872228 R14: 0000000000000201 R15: 00007fffda8720f0 [ 309.662572] ? __this_cpu_preempt_check+0x13/0x20 Fixes: 0eafec6d ("drm/i915: Enable lockless lookup of request tracking via RCU") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100192Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20170314115019.18127-1-chris@chris-wilson.co.ukReviewed-by:
Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170321144531.12344-1-chris@chris-wilson.co.ukSigned-off-by:
-
Chris Wilson authored
commit 8f68d591 upstream. On Baytrail, we manually calculate busyness over the evaluation interval to avoid issues with miscaluations with RC6 enabled. However, it turns out that the DOWN_EI interrupt generator is completely bust - it operates in two modes, continuous or never. Neither of which are conducive to good behaviour. Stop unmask the DOWN_EI interrupt and just compute everything from the UP_EI which does seem to correspond to the desired interval. v2: Fixup gen6_rps_pm_mask() as well v3: Inline vlv_c0_above() to combine the now identical elapsed calculation for up/down and simplify the threshold testing Fixes: 43cf3bf0 ("drm/i915: Improved w/a for rps on Baytrail") Signed-off-by:
Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170313170617.31564-1-chris@chris-wilson.co.uk (cherry picked from commit e0e8c7cb) Signed-off-by:
-
Kenneth Graunke authored
commit 0f5418e5 upstream. This patch makes the I915_PARAM_HAS_EXEC_CONSTANTS getparam return 0 (indicating the optional feature is not supported), and makes execbuf always return -EINVAL if the flags are used. Apparently, no userspace ever shipped which used this optional feature: I checked the git history of Mesa, xf86-video-intel, libva, and Beignet, and there were zero commits showing a use of these flags. Kernel commit 72bfa19c apparently introduced the feature prematurely. According to Chris, the intention was to use this in cairo-drm, but "the use was broken for gen6", so I don't think it ever happened. 'relative_constants_mode' has always been tracked per-device, but this has actually been wrong ever since hardware contexts were introduced, as the INSTPM register is saved (and automatically restored) as part of the render ring context. The software per-device value could therefore get out of sync with the hardware per-context value. This meant that using them is actually unsafe: a client which tried to use them could damage the state of other clients, causing the GPU to interpret their BO offsets as absolute pointers, leading to bogus memory reads. These flags were also never ported to execlist mode, making them no-ops on Gen9+ (which requires execlists), and Gen8 in the default mode. On Gen8+, userspace can write these registers directly, achieving the same effect. On Gen6-7.5, it likely makes sense to extend the command parser to support them. I don't think anyone wants this on Gen4-5. Based on a patch by Dave Gordon. v3: Return -ENODEV for the getparam, as this is what we do for other obsolete features. Suggested by Chris Wilson. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92448Signed-off-by:
Kenneth Graunke <kenneth@whitecape.org> Reviewed-by:
Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Reviewed-by:
-
Chris Wilson authored
commit 35a3abfd upstream. In order to prevent accessing the hpd registers outside of the display power wells, we should refrain from writing to the registers before the display interrupts are enabled. [ 4.740136] WARNING: CPU: 1 PID: 221 at drivers/gpu/drm/i915/intel_uncore.c:795 __unclaimed_reg_debug+0x44/0x50 [i915] [ 4.740155] Unclaimed read from register 0x1e1110 [ 4.740168] Modules linked in: i915(+) intel_gtt drm_kms_helper prime_numbers [ 4.740190] CPU: 1 PID: 221 Comm: systemd-udevd Not tainted 4.10.0-rc6+ #384 [ 4.740203] Hardware name: / , BIOS PYBSWCEL.86A.0027.2015.0507.1758 05/07/2015 [ 4.740220] Call Trace: [ 4.740236] dump_stack+0x4d/0x6f [ 4.740251] __warn+0xc1/0xe0 [ 4.740265] warn_slowpath_fmt+0x4a/0x50 [ 4.740281] ? insert_work+0x77/0xc0 [ 4.740355] ? fwtable_write32+0x90/0x130 [i915] [ 4.740431] __unclaimed_reg_debug+0x44/0x50 [i915] [ 4.740507] fwtable_read32+0xd8/0x130 [i915] [ 4.740575] i915_hpd_irq_setup+0xa5/0x100 [i915] [ 4.740649] intel_hpd_init+0x68/0x80 [i915] [ 4.740716] i915_driver_load+0xe19/0x1380 [i915] [ 4.740784] i915_pci_probe+0x32/0x90 [i915] [ 4.740799] pci_device_probe+0x8b/0xf0 [ 4.740815] driver_probe_device+0x2b6/0x450 [ 4.740828] __driver_attach+0xda/0xe0 [ 4.740841] ? driver_probe_device+0x450/0x450 [ 4.740853] bus_for_each_dev+0x5b/0x90 [ 4.740865] driver_attach+0x19/0x20 [ 4.740878] bus_add_driver+0x166/0x260 [ 4.740892] driver_register+0x5b/0xd0 [ 4.740906] ? 0xffffffffa0166000 [ 4.740920] __pci_register_driver+0x47/0x50 [ 4.740985] i915_init+0x5c/0x5e [i915] [ 4.740999] do_one_initcall+0x3e/0x160 [ 4.741015] ? __vunmap+0x7c/0xc0 [ 4.741029] ? kmem_cache_alloc+0xcf/0x120 [ 4.741045] do_init_module+0x55/0x1c4 [ 4.741060] load_module+0x1f3f/0x25b0 [ 4.741073] ? __symbol_put+0x40/0x40 [ 4.741086] ? kernel_read_file+0x100/0x190 [ 4.741100] SYSC_finit_module+0xbc/0xf0 [ 4.741112] SyS_finit_module+0x9/0x10 [ 4.741125] entry_SYSCALL_64_fastpath+0x17/0x98 [ 4.741135] RIP: 0033:0x7f8559a140f9 [ 4.741145] RSP: 002b:00007fff7509a3e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 [ 4.741161] RAX: ffffffffffffffda RBX: 00007f855aba02d1 RCX: 00007f8559a140f9 [ 4.741172] RDX: 0000000000000000 RSI: 000055b6db0914f0 RDI: 0000000000000011 [ 4.741183] RBP: 0000000000020000 R08: 0000000000000000 R09: 000000000000000e [ 4.741193] R10: 0000000000000011 R11: 0000000000000246 R12: 000055b6db0854d0 [ 4.741204] R13: 000055b6db091150 R14: 0000000000000000 R15: 000055b6db035924 v2: Set dev_priv->display_irqs_enabled to true for all platforms other than vlv/chv that manually control the display power domain. Fixes: 19625e85 ("drm/i915: Enable polling when we don't have hpd") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97798Suggested-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Mika Kuoppala authored
commit 34dc8993 upstream. Certain Baytrails, namely the 4 cpu core variants, have been plaqued by spurious system hangs, mostly occurring with light loads. Multiple bisects by various people point to a commit which changes the reclocking strategy for Baytrail to follow its bigger brethen: commit 8fb55197 ("drm/i915: Agressive downclocking on Baytrail") There is also a review comment attached to this commit from Deepak S on avoiding punit access on Cherryview and thus it was excluded on common reclocking path. By taking the same approach and omitting the punit access by not tweaking the thresholds when the hardware has been asked to move into different frequency, considerable gains in stability have been observed. With J1900 box, light render/video load would end up in system hang in usually less than 12 hours. With this patch applied, the cumulative uptime has now been 34 days without issues. To provoke system hang, light loads on both render and bsd engines in parallel have been used: glxgears >/dev/null 2>/dev/null & mpv --vo=vaapi --hwdec=vaapi --loop=inf vid.mp4 So far, author has not witnessed system hang with above load and this patch applied. Reports from the tenacious people at kernel bugzilla are also promising. Considering that the punit access frequency with this patch is considerably less, there is a possibility that this will push the, still unknown, root cause past the triggering point on most loads. But as we now can reliably reproduce the hang independently, we can reduce the pain that users are having and use a static thresholds until a root cause is found. v3: don't break debugfs and simplification (Chris Wilson) References: https://bugzilla.kernel.org/show_bug.cgi?id=109051 Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Len Brown <len.brown@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jani Nikula <jani.nikula@intel.com> Cc: fritsch@xbmc.org Cc: miku@iki.fi Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> CC: Michal Feix <michal@feix.cz> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Deepak S <deepak.s@linux.intel.com> Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by:
Mika Kuoppala <mika.kuoppala@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1487166779-26945-1-git-send-email-mika.kuoppala@intel.com (cherry picked from commit 6067a27d) Signed-off-by:
-
Ville Syrjälä authored
commit edd06b83 upstream. printks are slow so we should not be doing them from the vblank evade critical section. These could explain why we sometimes seem to blow past our 100 usec deadline. The problem has been there ever since commit bfd16b2a ("drm/i915: Make updating pipe without modeset atomic.") but it may not have been readily visible until commit e1edbd44 ("drm/i915: Complain if we take too long under vblank evasion.") increased our chances of noticing it. Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Fixes: bfd16b2a ("drm/i915: Make updating pipe without modeset atomic.") Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (cherry picked from commit c3f8ad57) Signed-off-by:
-
Imre Deak authored
commit d253371c upstream. After commit 2c7d0602 Author: Imre Deak <imre.deak@intel.com> Date: Mon Dec 5 18:27:37 2016 +0200 drm/i915/gen9: Fix PCODE polling during CDCLK change notification there is still one report of the CDCLK-change request timing out on a KBL machine, see the Reference link. On that machine the maximum time the request took to succeed was 34ms, so increase the timeout to 50ms. v2: - Change timeout from 100 to 50 ms to maintain the current 50 ms limit for atomic waits in the driver. (Chris, Tvrtko) Reference: https://bugs.freedesktop.org/show_bug.cgi?id=99345 Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by:
Imre Deak <imre.deak@intel.com> Acked-by:
-
- 12 Apr, 2017 3 commits
-
-
Greg Kroah-Hartman authored
-
Matjaz Hegedic authored
[ Upstream commit bba8376a ] The reboot quirk for ASUS EeeBook X205TA contains a typo in DMI_PRODUCT_NAME, improperly referring to X205TAW instead of X205TA, which prevents the quirk from being triggered. The model X205TAW already has a reboot quirk of its own. This fix simply removes the inappropriate final letter W. Fixes: 90b28ded ("x86/reboot/quirks: Add ASUS EeeBook X205TA reboot quirk") Signed-off-by:
Matjaz Hegedic <matjaz.hegedic@gmail.com> Link: http://lkml.kernel.org/r/1489064417-7445-1-git-send-email-matjaz.hegedic@gmail.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
-
Tobias Jakobi authored
[ Upstream commit d595259f ] This USB-SATA bridge chip is used in a StarTech enclosure for optical drives. Without the quirk MakeMKV fails during the key exchange with an installed BluRay drive: > Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED' > occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:2' Signed-off-by:
Tobias Jakobi <tjakobi@math.uni-bielefeld.de> Acked-by:
-
