- 08 Dec, 2011 5 commits
-
-
Luciano Coelho authored
-
Eyal Shapira authored
The user can pass broadcast SSID (ssid="") in the list of SSIDs for active scan. In this case the loop was attempting to match SSIDs in the filter list to this empty entry and marking them as HIDDEN (sending probe request) by mistake Signed-off-by:
Eyal Shapira <eyal@wizery.com> Signed-off-by:
Luciano Coelho <coelho@ti.com>
-
Eliad Peller authored
wl1271_tm_cmd_interrogate creates a reply skb, but doesn't send it (and thus just leaks it). Add the missing cfg80211_testmode_reply() call. Signed-off-by:
Eliad Peller <eliad@wizery.com> Signed-off-by:
-
Eliad Peller authored
During plt init we configure some redundant commands, which are not needed for plt (specifically, we shouldn't configure any role-specific params, as there are no active roles). remove them. Signed-off-by:
-
Eliad Peller authored
fix several issues in testmode test/interrogate commands: 1. check the driver state is not OFF. 2. wakeup the chip from elp (if needed) 3. fix memory leak in wl1271_tm_cmd_interrogate() Signed-off-by:
-
- 07 Dec, 2011 9 commits
-
-
Johannes Berg authored
This code has been on the list to remove for a long time, so disable it by default, add a warning to its Kconfig, and schedule it for removal in 3.5. The only known dependency, hal, has not required it since its 0.5.12 release, which was in early 2009 and hal has since been deprecated completely. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Nikolay Martynov authored
Enable ANI for ar9100 since it seems to be working fine (and as a matter of fact ANI was always performed for ar9100 since code which was supposed to disable it didn't achieve this goal). This patch sets config.enable_ani to default (true) value for ar9100. Signed-off-by:
Nikolay Martynov <mar.kolya@gmail.com> Signed-off-by:
-
Nikolay Martynov authored
Currently in ath9k code there is an attempt which is meant to disable ANI for ar9100 and ar9340. But it doesn't really achieve this. All it does is disable ANI init and setup (i.e. calls to ath9k_hw_ani_setup and ath9k_hw_ani_init). Since ath9k_hw_ani_setup is not called ah->config.ani_poll_interval is never initialized (i.e. it is always zero) and ath_ani_calibrate always executes ANI procedures (over uninitialized ANI parameters). Moreover, ath_ani_calibrate is being called each 1ms because common->ani.timer is set to zero interval because ah->config.ani_poll_interval==0 (and thus smallest value of all intervals). Normally it should not be called this often. This patch changes the code so config.enable_ani is used to check if ANI should be performed. config.enable_ani is initialized to true by default. This patch sets it to false for ar9100 and ar9340. Signed-off-by:
-
Nikolay Martynov authored
To help debugging write a log entry when long calibration, short calibration or ANI is performed. Signed-off-by:
-
Nikolay Martynov authored
Add missed space and change typo in calibration debugging log. Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Felix Fietkau authored
Recently more places in mac80211 call drv_flush to ensure proper order for state changes wrt. powersave, channel changes, etc. On some systems such calls lead to spurious logspam about failing to stop tx dma, as well as hardware resets that go along with that. Instead of dropping packets in a place where it's completely unnecessary, only do it when drop == true. Signed-off-by:
-
Felix Fietkau authored
Turning off the radio when mac80211 tells the driver that it's idle is not a good idea, as idle interfaces might still occasionally scan or send packets. The only time the radio can be safely turned off is when drv_stop has been called. In the mean time, use sc->ps_idle only to indicate network sleep vs full sleep. Move the LED GPIO changes out of the PCI suspend/resume path, the start/stop functions already take care of that. Signed-off-by:
-
Felix Fietkau authored
After waking up from full sleep, registers are accessible, but rx/tx typically fails. A fast channel change will not recover from this, so ensure that a full-sleep -> wake transition is always followed by a full reset. The reason why this hasn't created any serious problems yet is that it's hidden by the (wrong) behavior of enabling/disabling the radio when the wiphy idle state changes. Signed-off-by:
-
- 06 Dec, 2011 26 commits
-
-
Ben Greear authored
AP interfaces routinely call this logic, so just silently return when this happens instead of splatting the kernel logs. Reported-by:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
Ben Greear <greearb@candelatech.com> Signed-off-by:
-
Rafał Miłecki authored
Some cores are mapped in the fixed way, they registers can be accessed all the time. Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Johannes Berg authored
Arik's patch "mac80211: allow action frames with unknown BSSID in GO mode" allowed any action frames in P2P mode to go through, but only to cooked monitor interfaces as the IEEE80211_RX_RA_MATCH was still cleared. As a result my no-monitor patches broke invitation responses. Instead of allowing any action frames in P2P GO mode to go through with a wrong BSSID like that patch did, allow all public action frames. They will never be processed by mac80211, but can be reported via nl80211 then. Signed-off-by:
-
Johannes Berg authored
This fixes another regression from my "pass all fragments to driver at once" patches -- if the packet is being retransmitted then we don't go through all handlers, but we still need to move it to the skbs list, otherwise we run into the first warning in __ieee80211_tx() and leak the skb. Signed-off-by:
-
Don Fry authored
Move the notification structures for ucode operations from the iwl_priv structure to the iwl_shared structure, with associated code changes. Signed-off-by:
Don Fry <donald.h.fry@intel.com> Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
-
Don Fry authored
Move the ucode_type variable from the iwl_priv to the iwl_shared structure with associated code changes. Signed-off-by:
-
Don Fry authored
Replace the references to the iwl_priv structure with the iwl_trans structure as the priv structure is never referenced other than to access the trans structure. Rename from iwlagn to iwl. Signed-off-by:
-
Don Fry authored
iwl-agn-ucode is generic ucode operations, not limited just to iwlagn. Signed-off-by:
-
Wey-Yi Guy authored
The file dealing with all the operations through testmode, rename it. Signed-off-by:
-
Hsu, Kenny authored
Create new tm command for WOWLAN uCode loading to support further debugging function in userspace. - IWL_TM_CMD_APP2DEV_LOAD_WOWLAN_FW Signed-off-by:
Kenny Hsu <kenny.hsu@intel.com> Signed-off-by:
-
Johannes Berg authored
Using the actual shifted constants here allows one to read and or them more easily. Signed-off-by:
-
Johannes Berg authored
This is only used for TX debugging where there already is more debugging and tracing is more useful anyway, so remove it. Signed-off-by:
-
Johannes Berg authored
This debug level is unused, remove it. Signed-off-by:
-
Johannes Berg authored
This macro is unused right now. Signed-off-by:
-
Wey-Yi Guy authored
Signed-off-by:
-
Hsu, Kenny authored
Use generic chunk size of dumpit packet for all necessary testmode commands instead of add declaration individually. Signed-off-by:
-
Kenny Hsu authored
The size of sram may alter according to ucode type. Retrieve the maximum sram size by current ucode type for range checking to prevent wrong data access. Signed-off-by:
-
Hsu, Kenny authored
Create new testmode commands and attributes to suppot sram data reading. Because the amount of sram data may exceed single skb packet size. Using the nl80211 dump it funtion to deliver sram data to userspace. - IWL_TM_CMD_APP2DEV_READ_SRAM - IWL_TM_CMD_APP2DEV_DUMP_SRAM - IWL_TM_ATTR_SRAM_ADDR - IWL_TM_ATTR_SRAM_SIZE - IWL_TM_ATTR_SRAM_DUMP Signed-off-by:
-
Mohammed Shafi Shajakhan authored
max_streams for AR9462 is '2'. it does not fixes anything, but improves the code readability Signed-off-by:
Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
based on systems change to improve rx dynamic range, and enables heavy clip for 5G HT40 MCS0 to improve spectral mask power. also remove an unused function declaration Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Signed-off-by:
-
Larry Finger authored
A previous commit fixed a problem whereby the rtl8192c driver loaded the firmware from disk many times; however, the log message was not moved. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Alexander Simon authored
The HT mode is set by iw (previous patchsets). The interface is set into the specified HT mode. HT mode and capabilities are announced in beacons. If we add a station that uses HT also, the fastest matching HT mode will be used for transmission. That means if we are using HT40+ and we add a station running on HT40-, we would transfer at HT20. If we join an IBSS with HT40, but the secondary channel is not available, we will fall back into HT20 as well. Allow frame aggregation to start in IBSS mode. Signed-off-by:
Alexander Simon <an.alexsimon@googlemail.com> [siwu@hrz.tu-chemnitz.de: Updates] * remove implicit channel_type enum assumptions * use rate_control_rate_init() if channel type changed * remove channel flags check * activate HT IBSS feature support * slightly reword commit message * rebase on wireless-testing Signed-off-by:
Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by:
Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Reviewed-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Simon Wunderlich authored
* Follow 802.11n-2009 9.13.3.1 for protection mode and ADDBA * Send ADDBA only to HT STAs - implement 11.5.1.1 partially Signed-off-by:
-
Alexander Simon authored
Prepare cfg80211 for IBSS HT: * extend cfg80211 ibss struct with channel_type * Check if extension channel can be used * Export can_beacon_sec_chan for use in mac80211 (will be called from ibss.c later). Signed-off-by:
-
Thomas Meyer authored
The advantage of kcalloc is, that will prevent integer overflows which could result from the multiplication of number of elements and size and it is also a bit nicer to read. The semantic patch that makes this change is available in https://lkml.org/lkml/2011/11/25/107Signed-off-by:
Thomas Meyer <thomas@m3y3r.de> Signed-off-by:
-
Thomas Meyer authored
The advantage of kcalloc is, that will prevent integer overflows which could result from the multiplication of number of elements and size and it is also a bit nicer to read. The semantic patch that makes this change is available in https://lkml.org/lkml/2011/11/25/107Signed-off-by:
Gertjan van Wingerde <gwingerde@gmail.com> Acked-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
