Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Missing case was causing ethtool self test to print garbage
value in extra info section.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TX queue was being stopped at beginning of send path instead
of at the end when last descriptor is used.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enabling RX cut-thru mode yields better performance as received frames
start getting written to memory before a whole frame is received.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Increase the number of outstanding read and write AXI transactions from 1
to 8 for better performance.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix intermittent hangs in xgmac_rx_refill. If a ring buffer entry already
had an skb allocated, then xgmac_rx_refill would get stuck in a loop. This
can happen on a rx error when we just leave the skb allocated to the entry.

[ 7884.510000] INFO: rcu_preempt detected stall on CPU 0 (t=727315 jiffies)
[ 7884.510000] [<c0010a59>] (unwind_backtrace+0x1/0x98) from [<c006fd93>] (__rcu_pending+0x11b/0x2c4)
[ 7884.510000] [<c006fd93>] (__rcu_pending+0x11b/0x2c4) from [<c0070b95>] (rcu_check_callbacks+0xed/0x1a8)
[ 7884.510000] [<c0070b95>] (rcu_check_callbacks+0xed/0x1a8) from [<c0036abb>] (update_process_times+0x2b/0x48)
[ 7884.510000] [<c0036abb>] (update_process_times+0x2b/0x48) from [<c004e8fd>] (tick_sched_timer+0x51/0x94)
[ 7884.510000] [<c004e8fd>] (tick_sched_timer+0x51/0x94) from [<c0045527>] (__run_hrtimer+0x4f/0x1e8)
[ 7884.510000] [<c0045527>] (__run_hrtimer+0x4f/0x1e8) from [<c0046003>] (hrtimer_interrupt+0xd7/0x1e4)
[ 7884.510000] [<c0046003>] (hrtimer_interrupt+0xd7/0x1e4) from [<c00101d3>] (twd_handler+0x17/0x24)
[ 7884.510000] [<c00101d3>] (twd_handler+0x17/0x24) from [<c006be39>] (handle_percpu_devid_irq+0x59/0x114)
[ 7884.510000] [<c006be39>] (handle_percpu_devid_irq+0x59/0x114) from [<c0069aab>] (generic_handle_irq+0x17/0x2c)
[ 7884.510000] [<c0069aab>] (generic_handle_irq+0x17/0x2c) from [<c000cc8d>] (handle_IRQ+0x35/0x7c)
[ 7884.510000] [<c000cc8d>] (handle_IRQ+0x35/0x7c) from [<c033b153>] (__irq_svc+0x33/0xb8)
[ 7884.510000] [<c033b153>] (__irq_svc+0x33/0xb8) from [<c0244b06>] (xgmac_rx_refill+0x3a/0x140)
[ 7884.510000] [<c0244b06>] (xgmac_rx_refill+0x3a/0x140) from [<c02458ed>] (xgmac_poll+0x265/0x3bc)
[ 7884.510000] [<c02458ed>] (xgmac_poll+0x265/0x3bc) from [<c029fcbf>] (net_rx_action+0xc3/0x200)
[ 7884.510000] [<c029fcbf>] (net_rx_action+0xc3/0x200) from [<c0030cab>] (__do_softirq+0xa3/0x1bc)
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix net tx watchdog timeout recovery. The descriptor ring was reset,
but the DMA engine was not reset to the beginning of the ring.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set by the driver on packet recieve.
eth_type_trans already sets skb->dev to the proper value and it is not
referenced anywhere else in the dirver, thus making its setting unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set during ring init and skb alloc in rx.  It is
already being set to the proper value when eth_type_trans is called on packet
receive, and the skb->dev is not referenced anywhere else in the code.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set by the driver's skb alloc routine (which is
called in init and during rx).  It is already being set to the proper value when
eth_type_trans is called on packet receive, and the skb->dev is not referenced
anywhere else in the code.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set during ring init and skb alloc in rx.  It is
already being set to the proper value when eth_type_trans is called on packet
receive, and the skb->dev is not referenced anywhere else in the code.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set by the driver on packet recieve.
eth_type_trans already sets skb->dev to the proper value and it is not
referenced anywhere else in the dirver, thus making its setting unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Cc: linux-driver@qlogic.com
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set before calling eth_type_trans.
eth_type_trans already sets skb->dev to the proper value, thus making this
unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: linux-driver@qlogic.com
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set during ring init.  It is already being set
to the proper value when eth_type_trans is called on packet receive, and the
skb->dev is not referenced anywhere else in the code.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set before calling eth_type_trans.
eth_type_trans already sets skb->dev to the proper value, thus making this
unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set by the driver on packet recieve.
eth_type_trans already sets skb->dev to the proper value and it is not
referenced anywhere else in the dirver, thus making its setting unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set after calling eth_type_trans.
eth_type_trans already sets skb->dev to the proper value, thus making this
unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Roopa Prabhu <roprabhu@cisco.com>
Cc: Neel Patel <neepatel@cisco.com>
Cc: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set during ring init.  It is already being set
to the proper value when eth_type_trans is called on packet receive, and the
skb->dev is not referenced anywhere else in the code.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

URLs to neterion.com and s2io.com no longer resolve.  Remove all references to
these URLs in the driver source and documentation.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

On 64 bit arches having efficient unaligned accesses (eg x86_64) we can
use long words to reduce number of instructions for free.

Joe Perches suggested to change ipv6_masked_addr_cmp() to return a bool
instead of 'int', to make sure ipv6_masked_addr_cmp() cannot be used
in a sorting function.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert doxygen (or similar) formatted comments to kernel-doc or
unformatted comment.  Delete a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.  Delete
a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Defining a function with no parameters as 'T foo()' is the deprecated
K&R style, and is not strictly equivalent to defining it as 'T foo(void)'.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch series works towards the goal of minimizing the amount
of things that can change in an ipv4 route.

In a regime where the routing cache is removed, route changes will
lead to cloning in the FIB tables or similar.

The largest trigger of route metrics writes, TCP, now has it's own
cache of dynamic metric state.  The timewait timestamps are stored
there now as well.

As a result of that, pre-cowing metrics is no longer necessary,
and therefore FLOWI_FLAG_PRECOW_METRICS is removed.

Redirect and PMTU handling is moved back into the ipv4 routes.  I'm
sorry for all the headaches trying to do this in the inetpeer has
caused, it was the wrong approach for sure.

Since metrics become read-only for ipv4 we no longer need the inetpeer
hung off of the ipv4 routes either.  So those disappear too.

Also, timewait sockets no longer need to hold onto an inetpeer either.

After this series, we still have some details to resolve wrt. PMTU and
redirects for a route-cache-less system:

1) With just the plain route cache removal, PMTU will continue to
   work mostly fine.  This is because of how the local route users
   call down into the PMTU update code with the route they already
   hold.

   However, if we wish to cache pre-computed routes in fib_info
   nexthops (which we want for performance), then we need to add
   route cloning for PMTU events.

2) Redirects require more work.  First, redirects must be changed to
   be handled like PMTU.  Wherein we call down into the sockets and
   other entities, and then they call back into the routing code with
   the route they were using.

   So we'll be adding an ->update_nexthop() method alongside
   ->update_pmtu().

   And then, like for PMTU, we'll need cloning support once we start
   caching routes in the fib_info nexthops.

But that's it, we can completely pull the trigger and remove the
routing cache with minimal disruptions.

As it is, this patch series alone helps a lot of things.  For one,
routing cache entry creation should be a lot faster, because we no
longer do inetpeer lookups (even to check if an entry exists).

This patch series also opens the door for non-DST_HOST ipv4 routes,
because nothing fundamentally cares about rt->rt_dst any more.  It
can be removed with the base routing cache removal patch.  In fact,
that was the primary goal of this patch series.
Signed-off-by: David S. Miller <davem@davemloft.net>

No longer used.
Signed-off-by: David S. Miller <davem@davemloft.net>

Nothing every writes to ipv4 metrics any longer.

PMTU is stored in rt->rt_pmtu.

Dynamic TCP metrics are stored in a special TCP metrics cache,
completely outside of the routes.

Therefore ->cow_metrics() can simply nothing more than a WARN_ON
trigger so we can catch anyone who tries to add new writes to
ipv4 route metrics.
Signed-off-by: David S. Miller <davem@davemloft.net>

Blackhole routes have a COW metrics operation that returns NULL
always, therefore this dst_copy_metrics() call did absolutely
nothing.
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than at every struct rtable creation.
Signed-off-by: David S. Miller <davem@davemloft.net>

Maintaining this in the inetpeer entries was not the right way to do
this at all.
Signed-off-by: David S. Miller <davem@davemloft.net>

Nobody provides non-zero values any longer.
Signed-off-by: David S. Miller <davem@davemloft.net>

No longer needed.  TCP writes metrics, but now in it's own special
cache that does not dirty the route metrics.  Therefore there is no
longer any reason to pre-cow metrics in this way.
Signed-off-by: David S. Miller <davem@davemloft.net>

Only use it in the absolutely required cases:

1) COW'ing metrics

2) ipv4 PMTU

3) ipv4 redirects
Signed-off-by: David S. Miller <davem@davemloft.net>

No longer used.
Signed-off-by: David S. Miller <davem@davemloft.net>

No longer used.
Signed-off-by: David S. Miller <davem@davemloft.net>

With help from Lin Ming.
Signed-off-by: David S. Miller <davem@davemloft.net>