- 09 Dec, 2014 40 commits
-
-
David S. Miller authored
David L Stevens says: ==================== sunvnet: add SG, HW_CSUM, GSO, and TSO support This patch set adds everything needed for TSO support in sunvnet. On my test hardware, this increases the single-stream TCP throughput for the default 1500-byte MTU Linux-Linux from ~2Gbps to 10Gbps and Linux-Solaris from ~2Gbps to 6Gbps. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
David L Stevens authored
This patch adds TSO support for the sunvnet driver. Signed-off-by: David L Stevens <david.stevens@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David L Stevens authored
This patch adds GSO support to the sunvnet driver. Signed-off-by: David L Stevens <david.stevens@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David L Stevens authored
This patch adds support for sender-side checksum offloading. Signed-off-by: David L Stevens <david.stevens@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David L Stevens authored
This patch adds scatter/gather support to the sunvnet driver. Signed-off-by: David L Stevens <david.stevens@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David L Stevens authored
This patch adds support for VIO v1.7 (extended descriptor format) and v1.8 (receive-side checksumming) to the sunvnet driver. Signed-off-by: David L Stevens <david.stevens@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David L Stevens authored
This patch changes the name of vnet_port_alloc_tx_bufs to vnet_port_alloc_tx_ring, since there are no buffer allocations after transmit zero copy support was added. This patch also moves the ring allocation to after VIO version negotiation to allow for different-sized descriptors in later VIO versions. Signed-off-by: David L Stevens <david.stevens@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Amir Vadai says: ==================== ethtool, net/mlx4_en: RSS hash function selection This patchset by Eyal adds support in set/get of RSS hash function. Current supported functions are Toeplitz and XOR. The API is design to enable adding new hash functions without breaking backward compatibility. Userspace patch will be sent after API is available in kernel. The patchset was applied and tested over commit cd4c910e ("netpoll: delete defconfig references to obsolete NETPOLL_TRAP") ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eyal Perry authored
The ConnectX HW is capable of using one of the following hash functions: Toeplitz and an XOR hash function. This patch extends the implementation of the mlx4_en driver set/get_rxfh callbacks to support getting and setting the RSS hash function used by the device. Signed-off-by: Eyal Perry <eyalpe@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eyal Perry authored
This patch extends the set/get_rxfh ethtool-options for getting or setting the RSS hash function. It modifies drivers implementation of set/get_rxfh accordingly. This change also delegates the responsibility of checking whether a modification to a certain RX flow hash parameter is supported to the driver implementation of set_rxfh. User-kernel API is done through the new hfunc bitmask field in the ethtool_rxfh struct. A bit set in the hfunc field is corresponding to an index in the new string-set ETH_SS_RSS_HASH_FUNCS. Got approval from most of the relevant driver maintainers that their driver is using Toeplitz, and for the few that didn't answered, also assumed it is Toeplitz. Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Ariel Elior <ariel.elior@qlogic.com> Cc: Prashant Sreedharan <prashant@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Cc: Hariprasad S <hariprasad@chelsio.com> Cc: Sathya Perla <sathya.perla@emulex.com> Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com> Cc: Ajit Khaparde <ajit.khaparde@emulex.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: Bruce Allan <bruce.w.allan@intel.com> Cc: Carolyn Wyborny <carolyn.wyborny@intel.com> Cc: Don Skidmore <donald.c.skidmore@intel.com> Cc: Greg Rose <gregory.v.rose@intel.com> Cc: Matthew Vick <matthew.vick@intel.com> Cc: John Ronciak <john.ronciak@intel.com> Cc: Mitch Williams <mitch.a.williams@intel.com> Cc: Amir Vadai <amirv@mellanox.com> Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com> Cc: Shradha Shah <sshah@solarflare.com> Cc: Shreyas Bhatewara <sbhatewara@vmware.com> Cc: "VMware, Inc." <pv-drivers@vmware.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Eyal Perry <eyalpe@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
since head->handle == handle (checked before), just assign handle. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
rcu variant is not correct here. The code is called by updater (rtnl lock is held), not by reader (no rcu_read_lock is held). Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
rcu variant is not correct here. The code is called by updater (rtnl lock is held), not by reader (no rcu_read_lock is held). Signed-off-by: Jiri Pirko <jiri@resnulli.us> ACKed-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-nextDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2014-12-06 This series contains updates to i40e and i40evf. Shannon provides several patches to cleanup and fix i40e. First removes an unneeded break statement in i40e_vsi_link_event(). Then removes some debug messages that really do not give any useful information and ends up getting printed every service_task loop, which fills the logfile with noise when AQ tracing is enabled. Updates the aq_cmd arguments to use %i which is much more forgiving and user friendly than the more restrictive %x, or %d. Fixes the netdev_stat macro, where the old xxx_NETDEV_STAT() macro was defined long before the newer rtnl_link_stats64 came into being, and just never got updated. Getting the pf_id from the function number had an issue when when the PF was setup in passthru mode, the PCI bus/device/function was virtualized and the number in the VM is different from the number in the bare metal. This caused HW configuration issues when the wrong pf_id was used to set up the HMC and other structures. The PF_FUNC_RID register has the real bus/device/function information as configured by the BIOS, so use that for a better number. Carolyn adds additional text description for the base pf0 and flow director generated interrupts, since these interrupts are difficult to distinguish per port on a multi-function device. Jacob resolves an issue related to images with multiple PFs per physical port. We cannot fully support 1588 PTP features, since only one port should control (i.e. write) the registers at a time. Doing so can cause interference of functionality. Anjali provides several updates to i40e, first adds the Virtual Channel OP event opcode for CONFIG_RSS, so that the Virtual Channel state machine can properly decipher status change events. Then updates the driver to add (and use) i40e_is_vf macro for future expansion when new VF MAC types get added. Adds new update VSI flow to accommodate a firmware dix with VSI loopback mode. All VSIs on a VEB should either have loopback enabled or disabled, a mixed mode is not supported for a VEB. Since our driver supports multiple VSIs per PF that need to talk to each other make sure to enable Loopback for the PF and FDIR VSI as well. Mitch provides a couple of i40e and i40evf patches. First updates i40evf init code more adept at handling when multiple VFs attempt to initialize simultaneously. Joe Perches provides a i40e patch which resolves a compile warning about about frame size being larger than 2048 bytes by reducing the stack use by using kmemdup and not using a very large struct on the stack. v2: - Dropped patch 13 & 14 while Mitch reworks the patches based on feedback from Ben Hutchings, probably the tryptophan in the turkey is to blame for the delay... - Added Joe Perches patch which resolves a compile warning about frame size ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Alexander Duyck says: ==================== net: Add helper for padding short Ethernet frames This patch series adds a pair of helpers to pad short Ethernet frames. The general idea is to clean up a number of code paths that were all writing their own versions of the same or similar function. An added advantage is that this will help to discourage introducing new bugs as in at least one case I found the skb->len had been updated, but the tail pointer update was overlooked. v2: Added skb_put_padto for cases where length is not ETH_ZLEN Updated intel drivers and emulex driver to use skb_put_padto Updated eth_skb_pad to use skb_put_padto ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexander Duyck authored
Replace rtl_skb_pad with eth_skb_pad since they do the same thing. Cc: Realtek linux nic maintainers <nic_swsd@realtek.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexander Duyck authored
Update myri10ge to use eth_skb_pad helper. This also corrects a minor issue as the driver was updating length without updating the tail pointer. Cc: Hyong-Youb Kim <hykim@myri.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexander Duyck authored
Replace the standard layout for padding an ethernet frame with the eth_skb_pad call. Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexander Duyck authored
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexander Duyck authored
Update the Intel Ethernet drivers to use eth_skb_pad() and skb_put_padto instead of doing their own implementations of the function. Also this cleans up two other spots where skb_pad was called but the length and tail pointers were being manipulated directly instead of just having the padding length added via __skb_put. Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexander Duyck authored
This patch adds two new helper functions skb_put_padto and eth_skb_pad. These functions deviate from the standard skb_pad or skb_padto in that they will also update the length and tail pointers so that they reflect the padding added to the frame. The eth_skb_pad helper is meant to be used with Ethernet devices to update either Rx or Tx frames so that they report the correct size. The skb_put_padto helper is meant to be used primarily in the transmit path for network devices that need frames to be padded up to some minimum size and don't wish to simply update the length somewhere external to the frame. The motivation behind this is that there are a number of implementations throughout the network device drivers that are all doing the same thing, but each a little bit differently and as a result several implementations contain bugs such as updating the length without updating the tail offset and other similar issues. Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Eli Cohen says: ==================== mlx5 driver updates The following series contains some fixes to mlx5 as well as update to the list of supported devices. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eli Cohen authored
If mlx5_core_create_mkey fails, decrease the pending counter to undo the previous increment. Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eli Cohen authored
1. Add required __acquire/__release statements to balance spinlock usage. 2. Change the index parameter of begin_wqe() to be unsigned to match supplied argument type. Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eli Cohen authored
Add ConnectX-4LX to the list of supported devices as well as their virtual functions. Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Majd Dibbiny authored
The outbox should be cleared before executing the command. Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eli Cohen authored
Useful for debugging purposes. Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eli Cohen authored
These enumerations are not used so remove them. Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eli Cohen authored
Command queue descriptor page size is 4KB and not the page size used by the kernel. Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eli Cohen authored
mlx5 requires at least one interrupt vector for completions so fix the minvec argument to pci_enable_msix_range() accordingly. Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eli Cohen authored
Call request module on mlx5_ib so it will be available for applications requiring it, such as installers that require boot over IB. Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Chunhao Lin says: ==================== r8169:change hardware setting This patch series contains two hardware setting modification to prevent hardware become abnormal. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Chun-Hao Lin authored
Cmac engine is the bridge between driver and dash firmware. Other os may not disable cmac when leave. And r8169 did not allocate any resources for cmac engine. Disable it to prevent abnormal system behavior. Signed-off-by: Chunhao Lin <hau@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Chun-Hao Lin authored
For RTL8168G/GU/H/EP and RTL8411B remove enable tx/rx from its own hw_start function. This will prevent enable tx/rx before complete hardware tx/rx setting. Tx/Rx will be enabled in the end of function rtl_hw_start_8168. Signed-off-by: Chunhao Lin <hau@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Ying Xue says: ==================== tipc: convert name table read-write lock to RCU Now TIPC name table is statically allocated and is protected with a Read-Write lock. To enhance the performance of TIPC name table lookup, we are going to involve RCU lock to protect the name table. As a consequence, it becomes lockless to concurrently look up name table on read side. However, before the conversion can be successfully made, the following two things must be first done: - change allocation way of name table from static to dynamic - fix several incorrect locking policy issues ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ying Xue authored
Convert tipc name table read-write lock to RCU. After this change, a new spin lock is used to protect name table on write side while RCU is applied on read side. Signed-off-by: Ying Xue <ying.xue@windriver.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Tested-by: Erik Hugne <erik.hugne@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ying Xue authored
When a list_head variable is seen as a new entry to be added to a list head, it's unnecessary to be initialized with INIT_LIST_HEAD(). Signed-off-by: Ying Xue <ying.xue@windriver.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Tested-by: Erik Hugne <erik.hugne@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-