- 21 Dec, 2016 9 commits
-
-
Hans Verkuil authored
This race was discovered by running cec-compliance -A with the cec module debug parameter set to 2: suddenly the test would fail. It turns out that this happens when the test configures the adapter in non-blocking mode, then it waits for the CEC_EVENT_STATE_CHANGE event and once the event is received it unconfigures the adapter. What happened was that the unconfigure was executed while the configure was still transmitting the Report Features and Report Physical Address messages. This messed up the internal state of the cec_adapter. The fix is to transmit those messages with the adap->lock mutex held (this will just queue them up in the internal transmit queue, and not actually transmit anything yet). Only unlock the mutex once everything is done. The main thread will dequeue the messages from the internal transmit queue and transmit them one by one, unless an unconfigure was done, and in that case any messages are just dropped. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Hans Verkuil authored
It's only a small function and this makes it easier to switch to transmitting the message with adap->lock held in the next patch. Signed-off-by:
Hans Verkuil <hansverk@cisco.com> Signed-off-by:
-
Hans Verkuil authored
The fill function just fills in the cec_msg struct, it doesn't transmit the message. This is now done explicitly. This makes it possible to switch to transmitting this message with adap->lock held. Signed-off-by:
-
Hans Verkuil authored
The loop that sets the unused logical addresses to INVALID should be done before 'configured' is set to true. This ensures that cec_log_addrs is consistent before it will be used. Signed-off-by:
-
Hans Verkuil authored
This is a 2.0 only message, so it should return Feature Abort if the adapter is configured for CEC version 1.4. Right now it does nothing, which means that the sender will time out. Signed-off-by:
-
Hans Verkuil authored
When a pending message was canceled (e.g. due to a timeout), then the old tx_status info was overwritten instead of ORed. The same happened with the tx_error_cnt field. So just modify them instead of overwriting them. Signed-off-by:
-
Hans Verkuil authored
In the (very) small print of the REPORT_CURRENT_LATENCY message there is a line that says that the last byte of the message (audio out delay) is only present if the 'audio out compensated' value is 3. I missed this, and so if this message was sent with a total length of 6 (i.e. without the audio out delay byte), then it was rejected by the framework since a minimum length of 7 was expected. Fix this minimum length check and update the wrappers in cec-funcs.h to do the right thing based on the message length. Signed-off-by:
-
Sakari Ailus authored
The smiapp_suspend() and smiapp_resume() functions will end up being unused if CONFIG_PM is enabled but CONFIG_PM_SLEEP is disabled, causing a compiler warning from both of the function definitions. Fix this by marking the functions with __maybe_unused. Suggested-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Sakari Ailus authored
Power on the sensor when the module is loaded and power it off when it is removed. Signed-off-by:
-
- 12 Dec, 2016 6 commits
-
-
Laurent Pinchart authored
A break is missing resulting in the hue control enabling or disabling the decode completely. Fix it. Fixes: c43875f6 ("[media] tvp5150: replace MEDIA_ENT_F_CONN_TEST by a control") Cc: stable@vger.kernel.org Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Laurent Pinchart authored
The function is large and called in several places, don't inline it. Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Laurent Pinchart authored
The function is only referenced as a handler in the tvp5150_sd_media_ops structure, which is only used when CONFIG_MEDIA_CONTROLLER is set. Don't define the function and the structure when the configuration option is unset to avoid an unused function warning. Signed-off-by:
-
Mauro Carvalho Chehab authored
Now that we're storing usb_interface at em28xx struct, there's no good reason to keep storing usb_device, as we can get it from usb_interface. So, get rid of it. Signed-off-by: -
Mauro Carvalho Chehab authored
The usb_device->dev is not the right device for dev_foo() calls. Instead, it should use usb_interface->dev. Tested-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Mauro Carvalho Chehab authored
Changing the device name, causes it to be unable to remove the sysfs file, causing troubles if a device is removed and then re-inserted. [ 1010.310320] WARNING: CPU: 3 PID: 119 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x7b/0x90 [ 1010.310323] sysfs: cannot create duplicate filename '/bus/usb/devices/1-3.3' [ 1010.310325] Modules linked in: lgdt330x em28xx_dvb dvb_core em28xx_alsa tuner_xc2028 tuner tvp5150 em28xx_v4l videobuf2_vmalloc videobuf2_memops videobuf2_v4l2 videobuf2_core em28xx tveeprom v4l2_common videodev media xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 xt_tcpudp tun bridge stp llc ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter ip_tables x_tables cmac bnep cpufreq_powersave cpufreq_conservative cpufreq_userspace binfmt_misc parport_pc ppdev lp parport snd_hda_codec_hdmi iTCO_wdt snd_hda_codec_realtek iTCO_vendor_support snd_hda_codec_generic arc4 intel_rapl x86_pkg_temp_thermal iwlmvm intel_powerclamp coretemp kvm_intel mac80211 kvm i915 [ 1010.310383] irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel iwlwifi pl2303 aesni_intel btusb aes_x86_64 usbserial lrw btrtl gf128mul glue_helper btbcm ablk_helper cryptd btintel bluetooth drm_kms_helper cfg80211 drm psmouse pcspkr i2c_i801 e1000e serio_raw snd_hda_intel snd_soc_rt5640 snd_hda_codec snd_soc_rl6231 snd_soc_ssm4567 mei_me i2c_smbus rfkill snd_hda_core ptp mei snd_soc_core ehci_pci sg lpc_ich shpchp mfd_core ehci_hcd pps_core snd_hwdep i2c_algo_bit snd_compress snd_pcm sdhci_acpi snd_timer battery snd sdhci elan_i2c snd_soc_sst_acpi mmc_core fjes dw_dmac i2c_hid soundcore snd_soc_sst_match i2c_designware_platform video i2c_designware_core acpi_pad acpi_als kfifo_buf tpm_tis button industrialio tpm_tis_core tpm ext4 crc16 jbd2 fscrypto mbcache dm_mod joydev evdev hid_logitech_hidpp [ 1010.310449] sd_mod hid_logitech_dj usbhid hid ahci libahci crc32c_intel libata xhci_pci xhci_hcd scsi_mod usbcore fan thermal [ 1010.310464] CPU: 3 PID: 119 Comm: kworker/3:2 Not tainted 4.9.0-rc8+ #14 [ 1010.310466] Hardware name: /NUC5i7RYB, BIOS RYBDWi35.86A.0350.2015.0812.1722 08/12/2015 [ 1010.310487] Workqueue: usb_hub_wq hub_event [usbcore] [ 1010.310490] 0000000000000000 ffffffff848f56c5 ffff8803b1f7f858 0000000000000000 [ 1010.310496] ffffffff8414f8f8 ffff88030000001f ffffed00763eff07 ffff8803b1f7f8f0 [ 1010.310501] ffff8803b3ea1e60 0000000000000001 ffffffffffffffef ffff8803b45c6840 [ 1010.310505] Call Trace: [ 1010.310517] [<ffffffff848f56c5>] ? dump_stack+0x5c/0x77 [ 1010.310522] [<ffffffff8414f8f8>] ? __warn+0x168/0x1a0 [ 1010.310526] [<ffffffff8414f9e4>] ? warn_slowpath_fmt+0xb4/0xf0 [ 1010.310529] [<ffffffff8414f930>] ? __warn+0x1a0/0x1a0 [ 1010.310534] [<ffffffff845436c6>] ? kasan_kmalloc+0xa6/0xd0 [ 1010.310539] [<ffffffff846ec2fa>] ? kernfs_path_from_node+0x4a/0x60 [ 1010.310543] [<ffffffff846f66eb>] ? sysfs_warn_dup+0x7b/0x90 [ 1010.310547] [<ffffffff846f6f26>] ? sysfs_do_create_link_sd.isra.2+0xb6/0xd0 [ 1010.310553] [<ffffffff84cd5a08>] ? bus_add_device+0x318/0x6b0 [ 1010.310557] [<ffffffff846f8693>] ? sysfs_create_groups+0x83/0x110 [ 1010.310562] [<ffffffff84ccff87>] ? device_add+0x777/0x1350 [ 1010.310567] [<ffffffff84ccf810>] ? device_private_init+0x180/0x180 [ 1010.310583] [<ffffffffc00c0f77>] ? usb_new_device+0x707/0x1030 [usbcore] [ 1010.310598] [<ffffffffc00c58c5>] ? hub_event+0x1d65/0x3280 [usbcore] [ 1010.310604] [<ffffffff841eb4ab>] ? account_entity_dequeue+0x30b/0x4a0 [ 1010.310618] [<ffffffffc00c3b60>] ? hub_port_debounce+0x280/0x280 [usbcore] [ 1010.310624] [<ffffffff8407ccd0>] ? compat_start_thread+0x80/0x80 [ 1010.310629] [<ffffffff851f5cb4>] ? __schedule+0x704/0x1770 [ 1010.310633] [<ffffffff851f55b0>] ? io_schedule_timeout+0x390/0x390 [ 1010.310638] [<ffffffff84541783>] ? cache_reap+0x173/0x200 [ 1010.310642] [<ffffffff84197bed>] ? process_one_work+0x4ed/0xe60 [ 1010.310646] [<ffffffff84198642>] ? worker_thread+0xe2/0xfd0 [ 1010.310650] [<ffffffff8421f76c>] ? __wake_up_common+0xbc/0x160 [ 1010.310654] [<ffffffff84198560>] ? process_one_work+0xe60/0xe60 [ 1010.310658] [<ffffffff841a837c>] ? kthread+0x1cc/0x220 [ 1010.310663] [<ffffffff841a81b0>] ? kthread_park+0x80/0x80 [ 1010.310667] [<ffffffff841a81b0>] ? kthread_park+0x80/0x80 [ 1010.310671] [<ffffffff841a81b0>] ? kthread_park+0x80/0x80 [ 1010.310675] [<ffffffff852016f5>] ? ret_from_fork+0x25/0x30 Tested-by:
-
- 01 Dec, 2016 3 commits
-
-
Antti Palosaari authored
A register used to identify chip during probe was overwritten during firmware download and due to that later probe's for warm chip were failing. Detect chip from the another register, which is located on different register bank 2. Fixes: 94d0eaa4 ("[media] mn88472: move out of staging to media") Cc: <stable@vger.kernel.org> # v4.8+ Signed-off-by:
-
Antti Palosaari authored
A register used to identify chip during probe was overwritten during firmware download and due to that later probe's for warm chip were failing. Detect chip from the another register, which is located on different register bank 2. Fixes: 7908fad9 ("[media] mn88473: finalize driver") Cc: <stable@vger.kernel.org> # v4.8+ Signed-off-by:
-
Sean Young authored
"c77d17c0 [media] lirc: use-after free" introduces two problems: cdev_del() can be called with a NULL argument, and the kobject_put() path will cause a double free. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
- 30 Nov, 2016 9 commits
-
-
Marek Szyprowski authored
Exynos5433 SoC has MFC v8 hardware module, but it has more complex clock hierarchy, so a new compatible is added. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
-
Marek Szyprowski authored
This patch changes the code for handling clocks. Now clocks are defined per each device variant, what is a preparation for adding support for Exynos 5433 MFC V8, which has more clocks than all previous versions. Also use devm_clk_get() to simplify cleanup path. Signed-off-by:
-
Marek Szyprowski authored
This patch moves preparation of clocks from s5p_mfc_init_pm() (driver probe) to s5p_mfc_power_on() (start of device operation). This change will allow to use runtime power usage optimization on newer Samsung Exynos platforms (for example Exynos 5433). Signed-off-by:
-
Marek Szyprowski authored
After commit "s5p-mfc: Fix clock management in s5p_mfc_release function" all clocks related functions are called only when MFC device is really available, so there is no additional check needed for NULL gate clocks. This patch simplifies the code and kills IS_ERR_OR_NULL macro usage. Signed-off-by:
-
Marek Szyprowski authored
CONFIG_PM is always enabled on Exynos platforms, so remove dead code related to early development of MFC driver on platform without PM support. Signed-off-by:
-
Marek Szyprowski authored
Move clock disabling before turning power off. This will enable later to add calls to clk_prepare/unprepare in the s5p_mfc_power_off() function to avoid keeping clocks prepared all the time when driver is bound. Signed-off-by:
-
Marek Szyprowski authored
The maximum rate of special clock depends on SoC variant and should be set in device tree via assigned-clock-rates property, so remove the code which forces special clock to 200MHz. Signed-off-by:
-
Marek Szyprowski authored
Some applications don't check error codes from QBUF/DQBUF ioctls, so don't spam kernel log with errors if they fall into endless loop trying to queue next buffer after a failure. Signed-off-by:
-
Douglas Anderson authored
We do video allocation all the time and we need it to be fast. Plus TLB efficiency isn't terribly important for video. That means we want to set DMA_ATTR_ALLOC_SINGLE_PAGES. See also the previous change (commit 14d3ae2e "ARM: dma-mapping: Use DMA_ATTR_ALLOC_SINGLE_PAGES hint to optimize allocation"). [m.szyprowski: rebased patch onto v4.9-rc1 and adapted changes to latest videbuf2 changes, this simplifies code changes to only set proper dma attribute flag and comment the reason for it, added commit id of arch/arm/mm patch] Signed-off-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
-
- 29 Nov, 2016 4 commits
-
-
Ricardo Ribalda authored
HSV formats were missing the color encoding, which leads to an invalid ycbcr_enc value during get_fmt and try_fmt. Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by:
-
Ricardo Ribalda authored
Zero is not a valid value for hsv_enc. Set the field to a valid initial value. This is not a problem for vivid, because it sets the field to 180 via tpg_s_hsv_enc() on the control initialization, but it might be a source of errors for other drivers that use this code. Signed-off-by:
-
Hans Verkuil authored
The cec_allocate_adapter function doesn't need the parent device, only the cec_register_adapter function needs it. Drop the cec_devnode parent field, since devnode.dev.parent can be used instead. This change makes the framework consistent with other frameworks where the parent device is not used until the device is registered. Signed-off-by:
-
Dan Carpenter authored
A recent cleanup introduced a potential dereference of -EFAULT when we call kfree(map->menu_info). Fixes: 4cc5bed1 ("[media] uvcvideo: Use memdup_user() rather than duplicating its implementation") Signed-off-by:
-
- 25 Nov, 2016 7 commits
-
-
Arnd Bergmann authored
A recent cleanup had the right idea to remove the initialization of the error variable, but missed the actual benefit of that, which is that we get warnings if there is a bug in it. Now we get a warning about a bug that was introduced by this cleanup: drivers/media/platform/davinci/vpfe_capture.c: In function 'vpfe_probe': drivers/media/platform/davinci/vpfe_capture.c:1992:9: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized] This adds the missing initialization that the warning is about, and another one that was preexisting and that we did not get a warning for. That second bug has existed since the driver was first added. Fixes: efb74461 ("[media] DaVinci-VPFE-Capture: Delete an unnecessary variable initialisation in vpfe_probe()") Fixes: 7da8a6cb ("V4L/DVB (12248): v4l: vpfe capture bridge driver for DM355 and DM6446") [mchehab@s-opensource.com: fix a merge conflict] Signed-off-by:
-
Mauro Carvalho Chehab authored
Usually, I don't like fixing coding style issues on non-staging drivers, as it could be a mess pretty easy, and could become like a snow ball. That's the case of recent changes on two changesets: they disalign some statements. Yet, a care a lot with cx88 driver, as it was the first driver I touched at the Kernel, and I've been maintaining it since 2005. So, several of the coding style issues were due to my code. Per Andrey's suggestion, I ran checkpatch.pl in strict mode, with fixed several other issues, did some function alinments, but broke other alinments. So, I had to manually apply another round of manual fixes to make sure that everything is ok, and to make checkpatch happy with this patch. With this patch, checkpatch.pl is now happy when called with: ./scripts/checkpatch.pl -f --max-line-length=998 --ignore PREFER_PR_LEVEL Also, the 80-cols violations that made sense were fixed. Checkpatch would be happier if we convert it to use dev_foo(), but this is a more complex change. NOTE: there are some places with msleep(1). As this driver was written at the time that the default was to sleep at least 10ms on such calls (e. g. CONFIG_HZ=100), I replaced those calls by usleep_range(10000, 20000), with should be safe to avoid breakages. Fixes: 65bc2fe8 ("[media] cx88: convert it to use pr_foo() macros") Fixes: 7b61ba8f ("[media] cx88: make checkpatch happier") Suggested-by:
Andrey Utkin <andrey_utkin@fastmail.com> Signed-off-by:
-
Arnd Bergmann authored
Commit 4710b752 ("[media] v4l: Add Renesas R-Car FDP1 Driver") in the v4l-dvb tree adds CONFIG_VIDEO_RENESAS_FDP1. It calls into the FCP driver, but when there is no dependency, FCP might be a module while FDP1 is built-in. We have the same logic in VIDEO_RENESAS_VSP1, which also depends on FCP not being a module when it is built-in itself. drivers/media/platform/rcar_fdp1.o: In function `fdp1_pm_runtime_resume': rcar_fdp1.c:(.text.fdp1_pm_runtime_resume+0x78): undefined reference to `rcar_fcp_enable' drivers/media/platform/rcar_fdp1.o: In function `fdp1_pm_runtime_suspend': rcar_fdp1.c:(.text.fdp1_pm_runtime_suspend+0x14): undefined reference to `rcar_fcp_disable' drivers/media/platform/rcar_fdp1.o: In function `fdp1_probe': rcar_fdp1.c:(.text.fdp1_probe+0x15c): undefined reference to `rcar_fcp_get' Signed-off-by:
-
Arnd Bergmann authored
The new driver produces a warning when CONFIG_PM is disabled: platform/rcar_fdp1.c:2408:12: error: 'fdp1_pm_runtime_resume' defined but not used [-Werror=unused-function] platform/rcar_fdp1.c:2399:12: error: 'fdp1_pm_runtime_suspend' defined but not used [-Werror=unused-function] This marks the two functions as __maybe_unused. Fixes: 4710b752 ("[media] v4l: Add Renesas R-Car FDP1 Driver") Signed-off-by:
-
Shuah Khan authored
Remove obsolete media_device_get_devres(), media_device_find_devres(), and media_device_release_devres() interfaces. These interfaces are now obsolete. Signed-off-by:
Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
This function is too big and too complex, making really hard to understand what's there. Split it into sub-routines, in order to make it easier to be understood, and to allow gcc to better parse it. As a bonus, it gets rid of a goto in the middle of a routine. Signed-off-by: -
Mauro Carvalho Chehab authored
The dvb_net code has a really complex function, meant to handle DVB network packages: it is long, has several loops and ifs inside, and even cause warnings with gcc5. Prepare it to be split into smaller functions by storing all arguments and internal vars inside a struct. Signed-off-by:
-
- 23 Nov, 2016 2 commits
-
-
Markus Elfring authored
Reuse existing functionality from memdup_user() instead of keeping duplicate source code. This issue was detected by using the Coccinelle software. Signed-off-by:
Markus Elfring <elfring@users.sourceforge.net> Signed-off-by:
-
Edgar Thier authored
Those formats are implemented by The DFK 23UP1300, DFK 23UX249 and DFK 23UX250 USB 3.0 industrial cameras from The Imaging Source. Signed-off-by:
Edgar Thier <info@edgarthier.net> Acked-by:
-
