- 02 Jun, 2021 9 commits
-
-
Zheng Yongjun authored
wierdness ==> weirdness multicat ==> multicast limite ==> limit adddress ==> address operater ==> operator intial ==> initial smaler ==> smaller Communcation ==> Communication funcitons ==> functions everytime ==> every time Neigbor ==> Neighbor performace ==> performance Signed-off-by:
Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Zheng Yongjun authored
possibile ==> possible Signed-off-by:
David Ahern <dsahern@kernel.org> Signed-off-by:
-
Zheng Yongjun authored
Suppport ==> Support Signed-off-by:
-
Zheng Yongjun authored
underlaying ==> underlying Signed-off-by:
-
Zheng Yongjun authored
When kalloc or kmemdup failed, should return ENOMEM rather than ENOBUF. Signed-off-by:
-
Zheng Yongjun authored
When kalloc or kmemdup failed, should return ENOMEM rather than ENOBUF. Signed-off-by:
-
YueHaibing authored
If CONFIG_IGB_HWMON is n, gcc warns: drivers/net/ethernet/intel/igb/e1000_82575.c:2765:17: warning: ‘e1000_emc_therm_limit’ defined but not used [-Wunused-const-variable=] static const u8 e1000_emc_therm_limit[4] = { ^~~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/intel/igb/e1000_82575.c:2759:17: warning: ‘e1000_emc_temp_data’ defined but not used [-Wunused-const-variable=] static const u8 e1000_emc_temp_data[4] = { ^~~~~~~~~~~~~~~~~~~ Move it into #ifdef block to fix this. Signed-off-by:YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
YueHaibing authored
If CONFIG_PCI_IOV is n, make W=1 warns: drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:3909:33: warning: ‘cxgb4_mgmt_ethtool_ops’ defined but not used [-Wunused-const-variable=] static const struct ethtool_ops cxgb4_mgmt_ethtool_ops = { ^~~~~~~~~~~~~~~~~~~~~~ Move it into #ifdef block to fix this. Signed-off-by: -
YueHaibing authored
If CONFIG_PROC_FS is n, gcc warns: drivers/net/hamradio/bpqether.c:437:36: warning: ‘bpq_seqops’ defined but not used [-Wunused-const-variable=] static const struct seq_operations bpq_seqops = { ^~~~~~~~~~ Use #ifdef macro to gurad this. Signed-off-by:
-
- 01 Jun, 2021 31 commits
-
-
Wong Vee Khee authored
On Intel platforms, not all safety features are enabled on the hardware. The current implementation enable all safety features by default. This will cause mass error and warning printouts after the module is loaded. Introduce platform specific safety features flag to enable or disable each safety features. Signed-off-by:
Wong Vee Khee <vee.khee.wong@linux.intel.com> Signed-off-by:
-
Nigel Christian authored
In the case MICROREAD_CB_TYPE_READER_ALL clang reports a dead code warning. The error code assigned to variable err is already passed to async_cb(). The assignment is redundant and can be removed. Addresses-Coverity: ("Unused value") Signed-off-by:Nigel Christian <nigel.l.christian@gmail.com> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by:
-
David S. Miller authored
Peng Li says: ==================== net: hdlc: clean up some code style issues This patchset clean up some code style issues. ==================== Signed-off-by: -
Peng Li authored
Braces {} should be used on all arms of this statement. Signed-off-by:Peng Li <lipeng321@huawei.com> Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
-
Peng Li authored
Should not use assignment in if condition. Signed-off-by:
-
Peng Li authored
According to the chackpatch.pl, comparison to NULL could be written "!param". Signed-off-by:
-
Peng Li authored
According to the chackpatch.pl, EXPORT_SYMBOL(foo); should immediately follow its function/variable. Signed-off-by:
-
Peng Li authored
Fix the checkpatch error as "foo* bar" and should be "foo *bar". Signed-off-by:
-
Peng Li authored
This patch fixes the checkpatch error about missing a blank line after declarations. Signed-off-by:
-
Peng Li authored
This patch removes some redundant blank lines. Signed-off-by:
-
David S. Miller authored
Boris Sukholitko says: ==================== net/sched: act_vlan: Fix modify to allow 0 Currently vlan modification action checks existence of vlan priority by comparing it to 0. Therefore it is impossible to modify existing vlan tag to have priority 0. For example, the following tc command will change the vlan id but will not affect vlan priority: tc filter add dev eth1 ingress matchall action vlan modify id 300 \ priority 0 pipe mirred egress redirect dev eth2 The incoming packet on eth1: ethertype 802.1Q (0x8100), vlan 200, p 4, ethertype IPv4 will be changed to: ethertype 802.1Q (0x8100), vlan 300, p 4, ethertype IPv4 although the user has intended to have p == 0. The fix is to add tcfv_push_prio_exists flag to struct tcf_vlan_params and rely on it when deciding to set the priority. The same flag is used to avoid dumping unset vlan priority. Change Log: v3 -> v4: - revert tcf_vlan_get_fill_size change: total size calculation may race vs dump v2 -> v3: - Push assumes that the priority is being set - tcf_vlan_get_fill_size accounts for priority existence v1 -> v2: - Do not dump unset priority and fix tests accordingly - Test for priority 0 modification ==================== Reviewed-by:Davide Caratti <dcaratti@redhat.com> Signed-off-by:
-
Boris Sukholitko authored
Because explicitly being set, the priority 0 should appear in the output. Signed-off-by:
Boris Sukholitko <boris.sukholitko@broadcom.com> Signed-off-by:
-
Boris Sukholitko authored
Dump vlan priority only if it has been previously set. Fix the tests accordingly. Signed-off-by:
-
Boris Sukholitko authored
Currently vlan modification action checks existence of vlan priority by comparing it to 0. Therefore it is impossible to modify existing vlan tag to have priority 0. For example, the following tc command will change the vlan id but will not affect vlan priority: tc filter add dev eth1 ingress matchall action vlan modify id 300 \ priority 0 pipe mirred egress redirect dev eth2 The incoming packet on eth1: ethertype 802.1Q (0x8100), vlan 200, p 4, ethertype IPv4 will be changed to: ethertype 802.1Q (0x8100), vlan 300, p 4, ethertype IPv4 although the user has intended to have p == 0. The fix is to add tcfv_push_prio_exists flag to struct tcf_vlan_params and rely on it when deciding to set the priority. Fixes: 45a497f2 (net/sched: act_vlan: Introduce TCA_VLAN_ACT_MODIFY vlan action) Signed-off-by: -
Colin Ian King authored
There is a spelling mistake in a dev_warning message. Fix it. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Yang Li authored
Variable 'len' is set to conn_info->max_pkt_payload_len but this value is never read as it is overwritten with a new value later on, hence it is a redundant assignment and can be removed. Clean up the following clang-analyzer warning: net/nfc/nci/hci.c:164:3: warning: Value stored to 'len' is never read [clang-analyzer-deadcode.DeadStores] Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Yang Li <yang.lee@linux.alibaba.com> Reviewed-by:
-
Zheng Yongjun authored
variable 'status' is unneeded and it's noneed to check the return value of function vxge_reset_all_vpaths,so declare it as void. Signed-off-by:
-
Hayes Wang authored
Support get_pauseparam and set_pauseparam of ethtool_ops. Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
Shaokun Zhang authored
Function 'qlcnic_82xx_hw_write_wx_2M' is declared twice, so remove the repeated declaration. Cc: Shahed Shaikh <shshaikh@marvell.com> Cc: Manish Chopra <manishc@marvell.com> Cc: GR-Linux-NIC-Dev@marvell.com Signed-off-by:
Shaokun Zhang <zhangshaokun@hisilicon.com> Signed-off-by:
-
Zhen Lei authored
No functional change. Signed-off-by:
Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by:
-
Vladimir Oltean authored
After the refactoring introduced in commit 87614b93 ("net: enetc: create a common enetc_pf_to_port helper"), enetc_pf_to_port was coded up to return -1 in case the passed PCIe device does not have a recognized BDF. Make sure the -1 value is checked by the callers, to appease static checkers. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
-
Wander Lairson Costa authored
write_msg(netconsole.c:836) calls netpoll_send_udp after a call to spin_lock_irqsave, which normally disables interrupts; but in PREEMPT_RT this call just locks an rt_mutex without disabling irqs. In this case, netpoll_send_udp is called with interrupts enabled. Signed-off-by:
Wander Lairson Costa <wander@redhat.com> Signed-off-by:
-
David S. Miller authored
Vadym Kochan says: ==================== Marvell Prestera Switchdev initial updates for firmware version 3.0 This series adds minimal support for firmware version 3.0 which has such changes like: - initial routing support - LAG support - events interrupt handling changes Changes just make able to work with new firmware version but supported features in driver will be added later. New firmware version was recently merged into linux-firmware tree. Added ability of loading previous fw major version if the latest one is missing, also add support for previous FW ABI. PATCH -> RFC: 1) Load previous fw version if the latest one is missing (suggested by Andrew Lunn) 2) Add support for previous FW ABI version (suggested by Andrew Lunn) RFC v2: 1) Get rid of automatic decrementing of major version but hard code it. 2) Print error message with file path if previous FW could not be loaded. ==================== Signed-off-by: -
Vadym Kochan authored
Lets try to load previous fw version in case the latest one is missing on existing system. Signed-off-by:
Vadym Kochan <vkochan@marvell.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Vadym Kochan authored
New firmware version has some ABI and feature changes like: - LAG support - initial L3 support - changed events handling logic Signed-off-by: -
Vadym Kochan authored
Latest FW IPC flood message format was changed to configure uc/mc flooding separately, so change code according to this. Signed-off-by:
-
Vadym Kochan authored
There are change in firmware which requires that receiver will disable event interrupts before handling them and enable them after finish with handling. Events still may come into the queue but without receiver interruption. Signed-off-by:
-
Yang Yingliang authored
Add description for may_sleep to fix the W=1 warnings: drivers/net/ethernet/neterion/s2io.c:1110: warning: Function parameter or member 'may_sleep' not described in 'init_tti' drivers/net/ethernet/neterion/s2io.c:3335: warning: Function parameter or member 'may_sleep' not described in 'wait_for_cmd_complete' drivers/net/ethernet/neterion/s2io.c:4881: warning: Function parameter or member 'may_sleep' not described in 's2io_set_multicast' Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Signed-off-by:
-
Jakub Kicinski authored
Huazhong Tan says: ==================== net: hns3: add VLAN filter control support This patchset add VLAN filter control support for HNS3 driver. ==================== Link: https://lore.kernel.org/r/1622428725-30049-1-git-send-email-tanhuazhong@huawei.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Jian Shen authored
Add debugfs support for vlan configuraion. create a single file "vlan_config" for it, and query it by command "cat vlan_config", return the result to userspace. The new display style is below: $ cat vlan_config I_PORT_VLAN_FILTER: on E_PORT_VLAN_FILTER: off FUNC_ID I_VF_VLAN_FILTER E_VF_VLAN_FILTER PORT_VLAN_FILTER_BYPASS pf off on off vf0 off on off FUNC_ID PVID ACCEPT_TAG1 ACCEPT_TAG2 ACCEPT_UNTAG1 ACCEPT_UNTAG2 pf 0 on on on on vf0 0 on on on on Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
-
Jian Shen authored
Previously, there is hardware limitation for VF to modify the VLAN filter state, and the VLAN filter state is default enabled. Now the limitation has been removed in some device, so add capability flag to check whether the device supports modify VLAN filter state. If flag on, user will be able to modify the VLAN filter state by ethtool -K. VF needs to send mailbox to request the PF to modify the VLAN filter state for it. Signed-off-by:
-
