veth get_channel currently reports for channels being both RX/TX and
combined. As Jakub noted:

"""
ethtool man page is relatively clear, unfortunately the kernel code
is not and few read the man page. A channel is approximately an IRQ,
not a queue, and IRQ can't be dedicated and combined simultaneously
"""

This patch changes the information exposed by veth_get_channels,
setting max_combined to zero, being more consistent with the above
statement. The ethtool_channels is always cleared by the caller, we just
need to avoid setting the 'combined' fields.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

unix sockets allows to send file descriptors via SCM_RIGHTS type messages.
Each such send call forces kernel to allocate up to 2Kb memory for
struct scm_fp_list.

It makes sense to account for them to restrict the host's memory
consumption from inside the memcg-limited container.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Author: Andrey Ryabinin <aryabinin@virtuozzo.com>

The size of the ip_tunnel_prl structs allocation is controllable from
user-space, thus it's better to avoid spam in dmesg if allocation failed.
Also add __GFP_ACCOUNT as this is a good candidate for per-memcg
accounting. Allocation is temporary and limited by 4GB.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vlan array consume up to 8 pages of memory per net device.

It makes sense to account for them to restrict the host's memory
consumption from inside the memcg-limited container.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net namespace can create up to 64K tcp and dccp ports and force kernel
to allocate up to several megabytes of memory per netns
for inet_bind_bucket objects.

It makes sense to account for them to restrict the host's memory
consumption from inside the memcg-limited container.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

An netadmin inside container can use 'ip a a' and 'ip r a'
to assign a large number of ipv4/ipv6 addresses and routing entries
and force kernel to allocate megabytes of unaccounted memory
for long-lived per-netdevice related kernel objects:
'struct in_ifaddr', 'struct inet6_ifaddr', 'struct fib6_node',
'struct rt6_info', 'struct fib_rules' and ip_fib caches.

These objects can be manually removed, though usually they lives
in memory till destroy of its net namespace.

It makes sense to account for them to restrict the host's memory
consumption from inside the memcg-limited container.

One of such objects is the 'struct fib6_node' mostly allocated in
net/ipv6/route.c::__ip6_ins_rt() inside the lock_bh()/unlock_bh() section:

 write_lock_bh(&table->tb6_lock);
 err = fib6_add(&table->tb6_root, rt, info, mxc);
 write_unlock_bh(&table->tb6_lock);

In this case it is not enough to simply add SLAB_ACCOUNT to corresponding
kmem cache. The proper memory cgroup still cannot be found due to the
incorrect 'in_interrupt()' check used in memcg_kmem_bypass().

Obsoleted in_interrupt() does not describe real execution context properly.
>From include/linux/preempt.h:

 The following macros are deprecated and should not be used in new code:
 in_interrupt()	- We're in NMI,IRQ,SoftIRQ context or have BH disabled

To verify the current execution context new macro should be used instead:
 in_task()	- We're in task context
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Container netadmin can create a lot of fake net devices,
then create a new net namespace and repeat it again and again.
Net device can request the creation of up to 4096 tx and rx queues,
and force kernel to allocate up to several tens of megabytes memory
per net device.

It makes sense to account for them to restrict the host's memory
consumption from inside the memcg-limited container.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
net: bridge: multicast: add vlan support

This patchset adds initial per-vlan multicast support, most of the code
deals with moving to multicast context pointers from bridge/port pointers.
That allows us to switch them with the per-vlan contexts when a multicast
packet is being processed and vlan multicast snooping has been enabled.
That is controlled by a global bridge option added in patch 06 which is
off by default (BR_BOOLOPT_MCAST_VLAN_SNOOPING). It is important to note
that this option can change only under RTNL and doesn't require
multicast_lock, so we need to be careful when retrieving mcast contexts
in parallel. For packet processing they are switched only once in
br_multicast_rcv() and then used until the packet has been processed.
For the most part we need these contexts only to read config values and
check if they are disabled. The global mcast state which is maintained
consists of querier and router timers, the rest are config options.
The port mcast state which is maintained consists of query timer and
link to router port list if it's ever marked as a router port. Port
multicast contexts _must_ be used only with their respective global
contexts, that is a bridge port's mcast context must be used only with
bridge's global mcast context and a vlan/port's mcast context must be
used only with that vlan's global mcast context due to the router port
lists. This way a bridge port can be marked as a router in multiple
vlans, but might not be a router in some other vlan. Also this allows us
to have per-vlan querier elections, per-vlan queries and basically the
whole multicast state becomes per-vlan when the option is enabled.
One of the hardest parts is synchronization with vlan's memory
management, that is done through a new vlan flag: BR_VLFLAG_MCAST_ENABLED
which is changed only under multicast_lock. When a vlan is being
destroyed first that flag is removed under the lock, then the multicast
context is torn down which includes waiting for any outstanding context
timers. Since all of the vlan processing depends on BR_VLFLAG_MCAST_ENABLED
it must be checked first if the contexts are vlan and the multicast_lock
has been acquired. That is done by all IGMP/MLD packet processing
functions and timers. When processing a packet we have RCU so the vlan
memory won't be freed, but if the flag is missing we must not process it.
The timers are synchronized in the same way with the addition of waiting
for them to finish in case they are running after removing the flag
under multicast_lock (i.e. they were waiting for the lock). Multicast vlan
snooping requires vlan filtering to be enabled, if it's disabled then
snooping gets automatically disabled, too. BR_VLFLAG_GLOBAL_MCAST_ENABLED
controls if a vlan has BR_VLFLAG_MCAST_ENABLED set which is used in all
vlan disabled checks. We need both flags because one is controlled by
user-space globally (BR_VLFLAG_GLOBAL_MCAST_ENABLED) and the other is
for a particular bridge/vlan or port/vlan entry (BR_VLFLAG_MCAST_ENABLED).
Since the latter is also used for synchronization between the multicast
and vlan code, and also controlled by BR_VLFLAG_GLOBAL_MCAST_ENABLED we
rely on it when checking if a vlan context is disabled. The multicast
fast-path has 3 new bit tests on the cache-hot bridge flags field, I
didn't observe any measurable difference. I haven't forced either
context options to be always disabled when the other type is enabled
because the state consists of timers which either expire (router) or
don't affect the normal operation. Some options, like the mcast querier
one, won't be allowed to change for the disabled context type, that will
come with a future patch-set which adds per-vlan querier control.

Another important addition is the global vlan options, so far we had
only per bridge/port vlan options but in order to control vlan multicast
snooping globally we need to add a new type of global vlan options.
They can be changed only on the bridge device and are dumped only when a
special flag is set in the dump request. The first global option is vlan
mcast snooping control, it controls the vlan BR_VLFLAG_GLOBAL_MCAST_ENABLED
private flag. It can be set only on master vlan entries. There will be
many more global vlan options in the future both for multicast config
and other per-vlan options (e.g. STP).

There's a lot of room for improvements, I'll do some of the initial
ones but splitting the state to different contexts opens the door
for a lot more. Also any new multicast options become vlan-supported with
very little to no effort by using the same contexts.

Short patch description:
  patches 01-04: initial mcast context add, no functional changes
  patch      05: adds vlan mcast init and control helpers and uses them on
                 vlan create/destroy
  patch      06: adds a global bridge mcast vlan snooping knob (default
                 off)
  patches 07-08: add a helper for users which must derive the contexts
                 based on current bridge and vlan options (e.g. timers)
  patch      09: adds checks for disabled vlan contexts in packet
                 processing and timers
  patch      10: adds support for per-vlan querier and tagged queries
  patch      11: adds router port vlan id in the notifications
  patches 12-14: add global vlan options support (change, dump, notify)
  patch      15: adds per-vlan global mcast snooping control

Future patch-sets which build on this one (in order):
 - vlan state mcast handling
 - user-space mdb contexts (currently only the bridge contexts are used
   there)
 - all bridge multicast config options added per-vlan global and per
   vlan/port
 - iproute2 support for all the new uAPIs
 - selftests

This set has been stress-tested (deleting/adding ports/vlans while changing
vlan mcast snooping while processing IGMP/MLD packets), and also has
passed all bridge self-tests. I'm sending this set as early as possible
since there're a few more related sets that should go in the same
release to get proper and full mcast vlan snooping support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new global vlan option which controls whether multicast snooping
is enabled or disabled for a single vlan. It controls the vlan private
flag: BR_VLFLAG_GLOBAL_MCAST_ENABLED.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for global options notifications. They use only RTM_NEWVLAN
since global options can only be set and are contained in a separate
vlan global options attribute. Notifications are compressed in ranges
where possible, i.e. the sequential vlan options are equal.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new vlan options dump flag which causes only global vlan options
to be dumped. The dumps are done only with bridge devices, ports are
ignored. They support vlan compression if the options in sequential
vlans are equal (currently always true).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can have two types of vlan options depending on context:
 - per-device vlan options (split in per-bridge and per-port)
 - global vlan options

The second type wasn't supported in the bridge until now, but we need
them for per-vlan multicast support, per-vlan STP support and other
options which require global vlan context. They are contained in the global
bridge vlan context even if the vlan is not configured on the bridge device
itself. This patch adds initial netlink attributes and support for setting
these global vlan options, they can only be set (RTM_NEWVLAN) and the
operation must use the bridge device. Since there are no such options yet
it shouldn't have any functional effect.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the port multicast context to check if the router port is a vlan and
in case it is include its vlan id in the notification.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add basic vlan context querier support, if the contexts passed to
multicast_alloc_query are vlan then the query will be tagged. Also
handle querier start/stop of vlan contexts.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add helpers which check if the current bridge/port multicast context
should be used (i.e. they're not disabled) and use them for Rx IGMP/MLD
processing, timers and new group addition. It is important for vlans to
disable processing of timer/packet after the multicast_lock is obtained
if the vlan context doesn't have BR_VLFLAG_MCAST_ENABLED. There are two
cases when that flag is missing:
 - if the vlan is getting destroyed it will be removed and timers will
   be stopped
 - if the vlan mcast snooping is being disabled
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to use the new port group to port context helper in places where
we cannot pass down the proper context (i.e. functions that can be
called by timers or outside the packet snooping paths).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add br_multicast_pg_to_port_ctx() which returns the proper port multicast
context from either port or vlan based on bridge option and vlan flags.
As the comment inside explains the locking is a bit tricky, we rely on
the fact that BR_VLFLAG_MCAST_ENABLED requires multicast_lock to change
and we also require it to be held to call that helper. If we find the
vlan under rcu and it still has the flag then we can be sure it will be
alive until we unlock multicast_lock which should be enough.
Note that the context might change from vlan to bridge between different
calls to this helper as the mcast vlan knob requires only rtnl so it should
be used carefully and for read-only/check purposes.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a global knob that controls if vlan multicast snooping is enabled.
The proper contexts (vlan or bridge-wide) will be chosen based on the knob
when processing packets and changing bridge device state. Note that
vlans have their individual mcast snooping enabled by default, but this
knob is needed to turn on bridge vlan snooping. It is disabled by
default. To enable the knob vlan filtering must also be enabled, it
doesn't make sense to have vlan mcast snooping without vlan filtering
since that would lead to inconsistencies. Disabling vlan filtering will
also automatically disable vlan mcast snooping.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add helpers to enable/disable vlan multicast based on its flags, we need
two flags because we need to know if the vlan has multicast enabled
globally (user-controlled) and if it has it enabled on the specific device
(bridge or port). The new private vlan flags are:
 - BR_VLFLAG_MCAST_ENABLED: locally enabled multicast on the device, used
   when removing a vlan, toggling vlan mcast snooping and controlling
   single vlan (kernel-controlled, valid under RTNL and multicast_lock)
 - BR_VLFLAG_GLOBAL_MCAST_ENABLED: globally enabled multicast for the
   vlan, used to control the bridge-wide vlan mcast snooping for a
   single vlan (user-controlled, can be checked under any context)

Bridge vlan contexts are created with multicast snooping enabled by
default to be in line with the current bridge snooping defaults. In
order to actually activate per vlan snooping and context usage a
bridge-wide knob will be added later which will default to disabled.
If that knob is enabled then automatically all vlan snooping will be
enabled. All vlan contexts are initialized with the current bridge
multicast context defaults.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add global and per-port vlan multicast context, only initialized but
still not used. No functional changes intended.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass multicast context pointers to multicast functions instead of bridge/port.
This would make it easier later to switch these contexts to their per-vlan
versions. The patch is basically search and replace, no functional changes.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Factor out the bridge's global multicast context into a separate
structure which will later be used for per-vlan global context.
No functional changes intended.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Factor out the port's multicast context into a separate structure which
will later be shared for per-port,vlan context. No functional changes
intended. We need the structure even if bridge multicast is not defined
to pass down as pointer to forwarding functions.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I got below panic when doing fuzz test:

Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 4056 Comm: syz-executor.3 Tainted: G    B             5.14.0-rc1-00195-gcff5c4254439-dirty #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
Call Trace:
dump_stack_lvl+0x7a/0x9b
panic+0x2cd/0x5af
end_report.cold+0x5a/0x5a
kasan_report+0xec/0x110
ip_check_mc_rcu+0x556/0x5d0
__mkroute_output+0x895/0x1740
ip_route_output_key_hash_rcu+0x2d0/0x1050
ip_route_output_key_hash+0x182/0x2e0
ip_route_output_flow+0x28/0x130
udp_sendmsg+0x165d/0x2280
udpv6_sendmsg+0x121e/0x24f0
inet6_sendmsg+0xf7/0x140
sock_sendmsg+0xe9/0x180
____sys_sendmsg+0x2b8/0x7a0
___sys_sendmsg+0xf0/0x160
__sys_sendmmsg+0x17e/0x3c0
__x64_sys_sendmmsg+0x9e/0x100
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x462eb9
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8
 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48>
 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f3df5af1c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462eb9
RDX: 0000000000000312 RSI: 0000000020001700 RDI: 0000000000000007
RBP: 0000000000000004 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f3df5af26bc
R13: 00000000004c372d R14: 0000000000700b10 R15: 00000000ffffffff

It is one use-after-free in ip_check_mc_rcu.
In ip_mc_del_src, the ip_sf_list of pmc has been freed under pmc->lock protection.
But access to ip_sf_list in ip_check_mc_rcu is not protected by the lock.
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ronak Doshi says:

====================
vmxnet3: upgrade to version 6

vmxnet3 emulation has recently added several new features which includes
increase in queues supported, remove power of 2 limitation on queues,
add RSS for ESP IPv6, etc. This patch series extends the vmxnet3 driver
to leverage these new features.

Compatibility is maintained using existing vmxnet3 versioning mechanism as
follows:
- new features added to vmxnet3 emulation are associated with new vmxnet3
   version viz. vmxnet3 version 6.
- emulation advertises all the versions it supports to the driver.
- during initialization, vmxnet3 driver picks the highest version number
supported by both the emulation and the driver and configures emulation
to run at that version.

In particular, following changes are introduced:

Patch 1:
  This patch introduces utility macros for vmxnet3 version 6 comparison
  and updates Copyright information.

Patch 2:
  This patch adds support to increase maximum Tx/Rx queues from 8 to 32.

Patch 3:
  This patch removes the limitation of power of 2 on the queues.

Patch 4:
  Uses existing get_rss_hash_opts and set_rss_hash_opts methods to add
  support for ESP IPv6 RSS.

Patch 5:
  This patch reports correct RSS hash type based on the type of RSS
  performed.

Patch 6:
  This patch updates maximum configurable mtu to 9190.

Patch 7:
  With all vmxnet3 version 6 changes incorporated in the vmxnet3 driver,
  with this patch, the driver can configure emulation to run at vmxnet3
  version 6.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

With all vmxnet3 version 6 changes incorporated in the vmxnet3 driver,
the driver can configure emulation to run at vmxnet3 version 6, provided
the emulation advertises support for version 6.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch increases the maximum configurable mtu to 9190
to accommodate jumbo packets of overlay traffic.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As vmxnet3 supports IP/TCP/UDP RSS, this patch sets appropriate
hash type based on the type of RSS performed.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vmxnet3 version 4 added support for ESP RSS. However, only IPv4 was
supported. With vmxnet3 version 6, this patch enables RSS for ESP
IPv6 packets as well.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With version 6, vmxnet3 relaxes the restriction on queues to
be power of two. This is helpful in cases (Edge VM) where
vcpus are less than 8 and device requires more than 4 queues.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, vmxnet3 supports maximum of 8 Tx/Rx queues. With increase
in number of vcpus on a VM, to achieve better performance and utilize
idle vcpus, we need to increase the max number of queues supported.

This patch enhances vmxnet3 to support maximum of 32 Tx/Rx queues.
Increasing the Rx queues also increases the probability of distrubuting
the traffic from different flows to different queues with RSS.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3 is currently at version 4 and this patch initiates the
preparation to accommodate changes for upto version 6. Introduced
utility macros for vmxnet3 version 6 comparison and update Copyright
information.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, when userspace reads a datagram with a buffer that is
smaller than this datagram, the data will be truncated and only
part of it can be received by users. It doesn't seem right that
users don't know the datagram size and have to use a huge buffer
to read it to avoid the truncation.

This patch to fix it by keeping the skb in rcv queue until the
whole data is read by users. Only the last msg of the datagram
will be marked with MSG_EOR, just as TCP/SCTP does.

Note that this will work as above only when MSG_EOR is set in the
flags parameter of recvmsg(), so that it won't break any old user
applications.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nguy/next-queue

Tony Nguyen says:

====================
1GbE Intel Wired LAN Driver Updates 2021-07-16

Vinicius Costa Gomes says:

Add support for steering traffic to specific RX queues using Flex Filters.

As the name implies, Flex Filters are more flexible than using
Layer-2, VLAN or MAC address filters, one of the reasons is that they
allow "AND" operations more easily, e.g. when the user wants to steer
some traffic based on the source MAC address and the packet ethertype.

Future work include adding support for offloading tc-u32 filters to
the hardware.

The series is divided as follows:

Patch 1/5, add the low level primitives for configuring Flex filters.

Patch 2/5 and 3/5, allow ethtool to manage Flex filters.

Patch 4/5, when specifying filters that have multiple predicates, use
Flex filters.

Patch 5/5, Adds support for exposing the i225 LEDs using the LED subsystem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Each i225 has three LEDs. Export them via the LED class framework.

Each LED is controllable via sysfs. Example:

$ cd /sys/class/leds/igc_led0
$ cat brightness      # Current Mode
$ cat max_brightness  # 15
$ echo 0 > brightness # Mode 0
$ echo 1 > brightness # Mode 1

The brightness field here reflects the different LED modes ranging
from 0 to 15.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Currently flex filters are only used for filters containing user data.
However, it makes sense to utilize them also for filters having
multiple conditions, because that's not supported by the driver at the
moment. Add it.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Allows Flex Filters to be installed.

The previous restriction to the types of filters that can be installed
can now be lifted.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Use the flex filter mechanism to extend the current ethtool filter
operations by intercoperating the user data. This allows to match
eight more bytes within a Ethernet frame in addition to macs, ether
types and vlan.

The matching pattern looks like this:

 * dest_mac [6]
 * src_mac [6]
 * tpid [2]
 * vlan tci [2]
 * ether type [2]
 * user data [8]

This can be used to match Profinet traffic classes by FrameID range.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The Intel i225 NIC has the possibility to add flex filters which can
match up to the first 128 byte of a packet. These filters are useful
for all kind of packet matching. One particular use case is Profinet,
as the different traffic classes are distinguished by the frame id
range which cannot be matched by any other means.

Add code to configure and enable flex filters.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Implement Wake-on-LAN feature for 88X3310 and 88E2110.

This is done by enabling WoL interrupt and WoL detection and
configuring MAC address into WoL magic packet registers
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ling Pei Lee <pei.lee.ling@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>