There are multiple types of users of mtd->reboot_notifier.notifier_call:

(1) A while back, the cfi_cmdset_000{1,2} chip drivers implemented a
reboot notifier to (on a best effort basis) attempt to reset their flash
chips before rebooting.

(2) More recently, we implemented a common _reboot() hook so that MTD
drivers (particularly, NAND flash) could better halt I/O operations
without having to reimplement the same notifier boilerplate.

Currently, the WARN_ONCE() condition here was written to handle (2), but
at the same time it mis-diagnosed case (1) as an already-registered MTD.
Let's fix this by having the WARN_ONCE() condition better imitate the
condition that immediately follows it. (Wow, I don't know how I missed
that one.)

(Side note: Unfortunately, we can't yet combine the reboot notifier code
for (1) and (2) with a patch like [1], because some users of (1) also
use mtdconcat, and so the mtd_info struct from cfi_cmdset_000{1,2} won't
actually get registered with mtdcore, and therefore their reboot
notifier won't get registered.)

[1] http://patchwork.ozlabs.org/patch/417981/Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Jesper Nilsson <jespern@axis.com>
Cc: linux-cris-kernel@axis.com
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The in-band data are copied twice: before ECC correction and after the
ECC engine has fixed all the fixable bitflips.
Drop the useless memcpy_fromio operation by passing a NULL pointer when
calling sunxi_nfc_read_buf().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The sunxi_nfc_hw_ecc_read/write_chunk() functions try to avoid changing
the column address if unnecessary, but the logic to determine whether it's
necessary or not is currently wrong: it adds the ecc->bytes value to the
current offset where it should actually add ecc->size.

Fixes: 913821bd ("mtd: nand: sunxi: introduce sunxi_nfc_hw_ecc_read/write_chunk()")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Commit 073db4a5 ("mtd: fix: avoid race condition when accessing
mtd->usecount") fixed a race condition but due to poor ordering of the
mutex acquisition, introduced a potential deadlock.

The deadlock can occur, for example, when rmmod'ing the m25p80 module, which
will delete one or more MTDs, along with any corresponding mtdblock
devices. This could potentially race with an acquisition of the block
device as follows.

 -> blktrans_open()
    ->  mutex_lock(&dev->lock);
    ->  mutex_lock(&mtd_table_mutex);

 -> del_mtd_device()
    ->  mutex_lock(&mtd_table_mutex);
    ->  blktrans_notify_remove() -> del_mtd_blktrans_dev()
       ->  mutex_lock(&dev->lock);

This is a classic (potential) ABBA deadlock, which can be fixed by
making the A->B ordering consistent everywhere. There was no real
purpose to the ordering in the original patch, AFAIR, so this shouldn't
be a problem. This ordering was actually already present in
del_mtd_blktrans_dev(), for one, where the function tried to ensure that
its caller already held mtd_table_mutex before it acquired &dev->lock:

        if (mutex_trylock(&mtd_table_mutex)) {
                mutex_unlock(&mtd_table_mutex);
                BUG();
        }

So, reverse the ordering of acquisition of &dev->lock and &mtd_table_mutex so
we always acquire mtd_table_mutex first.

Snippets of the lockdep output follow:

  # modprobe -r m25p80
  [   53.419251]
  [   53.420838] ======================================================
  [   53.427300] [ INFO: possible circular locking dependency detected ]
  [   53.433865] 4.3.0-rc6 #96 Not tainted
  [   53.437686] -------------------------------------------------------
  [   53.444220] modprobe/372 is trying to acquire lock:
  [   53.449320]  (&new->lock){+.+...}, at: [<c043fe4c>] del_mtd_blktrans_dev+0x80/0xdc
  [   53.457271]
  [   53.457271] but task is already holding lock:
  [   53.463372]  (mtd_table_mutex){+.+.+.}, at: [<c0439994>] del_mtd_device+0x18/0x100
  [   53.471321]
  [   53.471321] which lock already depends on the new lock.
  [   53.471321]
  [   53.479856]
  [   53.479856] the existing dependency chain (in reverse order) is:
  [   53.487660]
  -> #1 (mtd_table_mutex){+.+.+.}:
  [   53.492331]        [<c043fc5c>] blktrans_open+0x34/0x1a4
  [   53.497879]        [<c01afce0>] __blkdev_get+0xc4/0x3b0
  [   53.503364]        [<c01b0bb8>] blkdev_get+0x108/0x320
  [   53.508743]        [<c01713c0>] do_dentry_open+0x218/0x314
  [   53.514496]        [<c0180454>] path_openat+0x4c0/0xf9c
  [   53.519959]        [<c0182044>] do_filp_open+0x5c/0xc0
  [   53.525336]        [<c0172758>] do_sys_open+0xfc/0x1cc
  [   53.530716]        [<c000f740>] ret_fast_syscall+0x0/0x1c
  [   53.536375]
  -> #0 (&new->lock){+.+...}:
  [   53.540587]        [<c063f124>] mutex_lock_nested+0x38/0x3cc
  [   53.546504]        [<c043fe4c>] del_mtd_blktrans_dev+0x80/0xdc
  [   53.552606]        [<c043f164>] blktrans_notify_remove+0x7c/0x84
  [   53.558891]        [<c04399f0>] del_mtd_device+0x74/0x100
  [   53.564544]        [<c043c670>] del_mtd_partitions+0x80/0xc8
  [   53.570451]        [<c0439aa0>] mtd_device_unregister+0x24/0x48
  [   53.576637]        [<c046ce6c>] spi_drv_remove+0x1c/0x34
  [   53.582207]        [<c03de0f0>] __device_release_driver+0x88/0x114
  [   53.588663]        [<c03de19c>] device_release_driver+0x20/0x2c
  [   53.594843]        [<c03dd9e8>] bus_remove_device+0xd8/0x108
  [   53.600748]        [<c03dacc0>] device_del+0x10c/0x210
  [   53.606127]        [<c03dadd0>] device_unregister+0xc/0x20
  [   53.611849]        [<c046d878>] __unregister+0x10/0x20
  [   53.617211]        [<c03da868>] device_for_each_child+0x50/0x7c
  [   53.623387]        [<c046eae8>] spi_unregister_master+0x58/0x8c
  [   53.629578]        [<c03e12f0>] release_nodes+0x15c/0x1c8
  [   53.635223]        [<c03de0f8>] __device_release_driver+0x90/0x114
  [   53.641689]        [<c03de900>] driver_detach+0xb4/0xb8
  [   53.647147]        [<c03ddc78>] bus_remove_driver+0x4c/0xa0
  [   53.652970]        [<c00cab50>] SyS_delete_module+0x11c/0x1e4
  [   53.658976]        [<c000f740>] ret_fast_syscall+0x0/0x1c
  [   53.664621]
  [   53.664621] other info that might help us debug this:
  [   53.664621]
  [   53.672979]  Possible unsafe locking scenario:
  [   53.672979]
  [   53.679169]        CPU0                    CPU1
  [   53.683900]        ----                    ----
  [   53.688633]   lock(mtd_table_mutex);
  [   53.692383]                                lock(&new->lock);
  [   53.698306]                                lock(mtd_table_mutex);
  [   53.704658]   lock(&new->lock);
  [   53.707946]
  [   53.707946]  *** DEADLOCK ***

Fixes: 073db4a5 ("mtd: fix: avoid race condition when accessing mtd->usecount")
Reported-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: <stable@vger.kernel.org>

Parsing direct subnodes of a mtd device as partitions is unreliable
since the mtd device is also part of its bus subsystem and can contain
bus data in subnodes.

Move ofpart data to a subnode of its own so it is clear which data is
part of the partition layout.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

To avoid conflict with other drivers using subnodes of the mtd device
create only one ofpart-specific node rather than any number of
arbitrary partition subnodes.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Just like other NAND controllers, the NAND READID command only works
in 8bit mode for all versions of BRCMNAND controller.

This patch forces 8bit mode for each NAND CS in brcmnand_init_cs()
before doing nand_scan_ident() to ensure that BRCMNAND controller
is in 8bit mode when NAND READID command is issued.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Use enum instead of magic numbers for CFG and CFG_EXT bitfields.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Anup Patel <anup.patel@broadcom.com>

Due to wrong assumption in ofpart ofpart fails on Exynos on SPI chips
with no partitions because the subnode containing controller data
confuses the ofpart parser.

Thus compiling in ofpart support automatically fails probing any SPI NOR
flash without partitions on Exynos.

Compiling in a partitioning scheme should not cause probe of otherwise
valid device to fail.

Instead, let's do the following:
 * try parsers until one succeeds
 * if no parser succeeds, report the first error we saw
 * even in the failure case, allow MTD to probe, with fallback
   partitions or no partitions at all -- the master device will still be
   registered

Issue report and comments initially by Michal Suchanek.
Reported-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Change the READ/WRITE to FSL_READ/FSL_WRITE to resolve any possible
namespace collisions with READ/WRITE macros (e.g., from <linux/fs.h>).

Problems have been seen, for example, on mips:

>> drivers/mtd/spi-nor/fsl-quadspi.c:186:5: error: 'LUT_0' undeclared (first use in this function)
      ((LUT_##ins) << INSTR0_SHIFT))
        ^
>> drivers/mtd/spi-nor/fsl-quadspi.c:188:30: note: in expansion of macro 'LUT0'

On SPARC:

drivers/mtd/spi-nor/fsl-quadspi.c: In function 'fsl_qspi_init_lut':
drivers/mtd/spi-nor/fsl-quadspi.c:369:1: error: 'LUT_0' undeclared (first use in this function)
drivers/mtd/spi-nor/fsl-quadspi.c:418:1: error: pasting "LUT_" and "(" does not give a valid preprocessing token
drivers/mtd/spi-nor/fsl-quadspi.c:418:2: error: implicit declaration of function 'LUT_'

And surely on others.

Fixes: d26a22d0 ("mtd: fsl-quadspi: allow building for other ARCHes with COMPILE_TEST")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Han Xu <b45815@freescale.com>
[Brian: rewrote commit description]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

When CONFIG_MTD_PARTITIONED_MASTER=y, it is fatal to call
mtd_device_parse_register() twice on the same MTD, as we try to register
the same device/kobject multipile times.

When CONFIG_MTD_PARTITIONED_MASTER=n, calling
mtd_device_parse_register() is more of just a nuisance, as we can mostly
navigate around any conflicting actions.

But anyway, doing so is a Bad Thing (TM), and we should complain loudly
for any drivers that try to do this.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>

Since commit 3efe41be ("mtd: implement common reboot notifier
boilerplate"), we might try to register a reboot notifier for an MTD
that failed to register. Let's avoid this by making the error path
clearer.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>

Changes the 32-bit time type timeval to the 64-bit time type
ktime_t, since 32-bit systems using struct timeval will break in the
year 2038. Correspondingly change do_gettimeofday() to ktime_get()
since ktime_get returns a ktime_t, but do_gettimeofday returns a
struct timeval.Here, ktime_get() is used instead of ktime_get_real()
since ktime_get() uses monotonic clock.
Signed-off-by: Shraddha Barke <shraddha.6596@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This patch adds support for 4-bit ECC BCH4 for the SPEAr600 SoC. This can
be used by boards equipped with a NAND chip that requires 4-bit ECC
strength. The SPEAr600 HW ECC only supports 1-bit ECC strength.

To enable SW BCH4, you need to specify this in your nand controller
DT node:

	nand-ecc-mode = "soft_bch";
	nand-ecc-strength = <4>;
	nand-ecc-step-size = <512>;

Tested on a custom SPEAr600 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
[Brian: tweaked the comments a bit]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>

If nand_wait_ready() times out, this is silently ignored, and its
caller will then proceed to read from/write to the chip before it is
ready. This can potentially result in corruption with no indication as
to why.

While a 20ms timeout seems like it should be plenty enough, certain
behaviour can cause it to timeout much earlier than expected. The
situation which prompted this change was that CPU 0, which is
responsible for updating jiffies, was holding interrupts disabled
for a fairly long time while writing to the console during a printk,
causing several jiffies updates to be delayed. If CPU 1 happens to
enter the timeout loop in nand_wait_ready() just before CPU 0 re-
enables interrupts and updates jiffies, CPU 1 will immediately time
out when the delayed jiffies updates are made. The result of this is
that nand_wait_ready() actually waits less time than the NAND chip
would normally take to be ready, and then read_page() proceeds to
read out bad data from the chip.

The situation described above may seem unlikely, but in fact it can be
reproduced almost every boot on the MIPS Creator Ci20.

Therefore, this patch increases the timeout to 400ms. This should be
enough to cover cases where jiffies updates get delayed. In nand_wait()
the timeout was previously chosen based on whether erasing or
programming. This is changed to be 400ms unconditionally as well to
avoid similar problems there. nand_wait() is also slightly refactored
to be consistent with nand_wait{,_status}_ready(). These changes should
have no effect during normal operation.

Debugging this was made more difficult by the misleading comment above
nand_wait_ready() stating "The timeout is caught later" - no timeout was
ever reported, leading me away from the real source of the problem.
Therefore, a pr_warn() is added when a timeout does occur so that it is
easier to pinpoint similar problems in future.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Reviewed-by: Niklas Cassel <niklas.cassel@axis.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Smatch found a bug in the error handling:

	drivers/mtd/devices/docg3.c:1634 doc_register_sysfs()
	error: buffer overflow 'doc_sys_attrs' 4 <= 4

The problem is that if the very last device_create_file() fails, then we
are beyond the end of the array.  Actually, any time i == 3 then there
is a problem.  We can fix this an simplify the code at the same time by
moving the !ret conditions out of the for loops and using a goto
instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

With the previous modifications, lots of pxa3xx specific definitions can
be removed.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Rework the pxa3xx_nand driver to allow using functions exported by the
nand framework to detect the flash and the timings. Then setup the
timings using the helpers previously added.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Add helpers to setup the timings in the pxa3xx driver. These helpers
allow to either make use of the nand framework nand_sdr_timings or the
pxa3xx specific pxa3xx_nand_host, for compatibility reasons.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Using readsl() result in a build error on i386. Fix this by using
ioread32_rep() instead, to allow compile testing the pxa3xx nand driver
on other architectures later.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

If common clock framework is configured, the driver generates a warning,
which is fixed by this change:

    WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
    Modules linked in:
    CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc2+ #206
    Hardware name: LPC32XX SoC (Flattened Device Tree)
    Backtrace:
    [<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
    [<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
    [<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
    [<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
    [<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
    [<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
    [<>] (clk_enable) from [<>] (lpc32xx_nand_probe+0x208/0x248)
    [<>] (lpc32xx_nand_probe) from [<>] (platform_drv_probe+0x50/0xa0)
    [<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
    [<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
    [<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
    [<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
    [<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
    [<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
    [<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
    [<>] (__platform_driver_register) from [<>] (lpc32xx_nand_driver_init+0x18/0x20)
    [<>] (lpc32xx_nand_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
    [<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
    [<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
    [<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

If common clock framework is configured, the driver generates a warning,
which is fixed by this change:

    WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
    Modules linked in:
    CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc2+ #201
    Hardware name: LPC32XX SoC (Flattened Device Tree)
    Backtrace:
    [<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
    [<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
    [<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
    [<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
    [<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
    [<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
    [<>] (clk_enable) from [<>] (lpc32xx_nand_probe+0x290/0x568)
    [<>] (lpc32xx_nand_probe) from [<>] (platform_drv_probe+0x50/0xa0)
    [<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
    [<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
    [<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
    [<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
    [<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
    [<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
    [<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
    [<>] (__platform_driver_register) from [<>] (lpc32xx_nand_driver_init+0x18/0x20)
    [<>] (lpc32xx_nand_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
    [<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
    [<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
    [<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

We got the syntax wrong here. Compile tested this time!

Error:

   drivers/mtd/maps/rbtx4939-flash.c: In function 'rbtx4939_flash_probe':
>> drivers/mtd/maps/rbtx4939-flash.c:99:11: error: request for member 'dev' in something not a structure or union
     info->mtd.dev.parent = &dev->dev;
              ^

Fixes: 9aa7e502 ("mtd: maps: rbtx4939-flash: show parent device in sysfs")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Frans Klaver <fransklaver@gmail.com>

Kernel headers should use linux/types.h instead.
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

We should prevent user to erasing mtd device with
an unaligned offset or length.
Signed-off-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The old PM model is deprecated. This is equivalent.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>

mtd_{suspend,resume}() get called from mtdcore in a class suspend/resume
callback. We don't need to call them again here. In practice, this would
actually work OK, as nand_base actually handles nesting OK -- it just
might print warnings.

Untested, but there are few (no?) users of PM for this driver AFAIK.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>

Building for x86 results in the following build errors:

   drivers/mtd/spi-nor/fsl-quadspi.c: In function 'fsl_qspi_init_lut':
>> drivers/mtd/spi-nor/fsl-quadspi.c:355:21: error: 'SZ_16M' undeclared (first use in this function)
     if (q->nor_size <= SZ_16M) {
                        ^
   drivers/mtd/spi-nor/fsl-quadspi.c:355:21: note: each undeclared identifier is reported only once for each function it appears in
   drivers/mtd/spi-nor/fsl-quadspi.c: In function 'fsl_qspi_read':
>> drivers/mtd/spi-nor/fsl-quadspi.c:208:27: error: 'SZ_4M' undeclared (first use in this function)
    #define QUADSPI_MIN_IOMAP SZ_4M
                              ^
>> drivers/mtd/spi-nor/fsl-quadspi.c:845:25: note: in expansion of macro 'QUADSPI_MIN_IOMAP'
      q->memmap_len = len > QUADSPI_MIN_IOMAP ? len : QUADSPI_MIN_IOMAP;

Explicitly include <linux/sizes.h> to fix the problem.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This driver doesn't actually need ARCH_MXC to compile. Relax the
constraints.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Han xu <han.xu@freescale.com>

Seen when compile-testing on non-32-bit arch:

    CC      drivers/mtd/spi-nor/fsl-quadspi.o
  drivers/mtd/spi-nor/fsl-quadspi.c: In function 'fsl_qspi_read':
  drivers/mtd/spi-nor/fsl-quadspi.c:873:2: warning: format '%d' expects argument of type 'int', but argument 6 has type 'size_t' [-Wformat=]
    dev_dbg(q->dev, "cmd [%x],read from 0x%p, len:%d\n",
    ^

Also drop the '0x' prefixing to the '%p' formatter, since %p already
knows how to format pointers appropriately.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Han xu <han.xu@freescale.com>

These flash support dual and quad read. Tested dual read on the 32 Mbit
version.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

In case the flash was locked at boot time.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Many other flash share the same features as ST Micro. I've tested some
Winbond flash, so add them.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This enables ioctl(MEMISLOCKED). Status can now be reported in the
mtdinfo or flash_lock utilities found in mtd-utils.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This code was a bit sloppy, would produce a lot of copy-and-paste, and
did not always provide a sensible interface:

 * It didn't validate the length for LOCK and the offset for UNLOCK, so
   we were essentially discarding half of the user-supplied data and
   assuming what they wanted to lock/unlock
 * It didn't do very good error checking
 * It didn't make use of the fact that this operation works on
   power-of-two dimensions

So, rewrite this to do proper bit arithmetic rather than a bunch of
hard-coded condition tables. Now we have:

 * More comments on how this was derived
 * Notes on what is (and isn't) supported
 * A more exendible function, so we could add support for other
   protection ranges
 * More accurate locking - e.g., suppose the top quadrant is locked (75%
   to 100%); then in the following cases, case (a) will succeed but (b)
   will not (return -EINVAL):
     (a) user requests lock 3rd quadrant (50% to 75%)
     (b) user requests lock 3rd quadrant, minus a few blocks (e.g., 50%
         to 73%)
   Case (b) *should* fail, since we'd have to lock blocks that weren't
   requested. But the old implementation didn't know the difference and
   would lock the entire second half (50% to 100%)

This refactoring work will also help enable the addition of
mtd_is_locked() support and potentially the support of bottom boot
protection (TB=1).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

I got the names of these fields wrong.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

No functional change, just cosmetic.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

These are often similar for CFI (parallel NOR) and for SPI NOR, but they
aren't always the same, for various reasons (different namespaces,
company acquisitions and renames, etc.). And some don't have CFI_MFR_*
entries at all.

So let's make a proper place to list the SPI NOR IDs, with all the SPI
NOR specific assumptions and comments.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

These status bits use different ways of representing similar integer
constants -- some are decimal, some are hex. Make them more consistent.

At the same time, impose my own preference, since IMO it's clearer what
these are when using the BIT() macro.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>