This Cadence QSPI IP has a 4-bit clock divisor field
for baud rate division.  For example:

0b0000 = /2
0b0001 = /4
0b0010 = /6
...
0b1111 = /32

The maximum divisor is 32
(when div = CQSPI_REG_CONFIG_BAUD_MASK).

If we assume a reference clock of 500MHz and we set
our spi-max-frequency to something low, such as 10 MHz.
The calculated bit field for the divisor ends up being:

DIV_ROUND_UP(500000000/(2*10000000))-1 = 25

25 is 0b11001... which truncates to a divisor field of 0b1001 (or /20).

This is higher than our anticipated max-frequency of 10MHz
(500MHz/20 = 25 MHz).  Instead, let's make sure we're always using
the maximum divisor (/32) in this case and give the user a warning about
the rate adjustment.
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Link: https://lore.kernel.org/r/20221128164147.158441-1-nathan.morrison@timesys.comSigned-off-by: Mark Brown <broonie@kernel.org>

Implement suspend, resume callbacks, store config at suspend and restore
config at time of resume
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Link: https://lore.kernel.org/r/20221006050514.115564-3-tharunkumar.pasumarthi@microchip.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add missing "reg = <0>;" property to the flash@0 node in the example.

Fixes: dd71cd4d ("spi: Add Nuvoton WPCM450 Flash Interface Unit (FIU) bindings")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221129102225.3598044-3-j.neuschaefer@gmx.netSigned-off-by: Mark Brown <broonie@kernel.org>

The nuvoton,wpcm450-fiu binding's example includes
nuvoton,wpcm450-clk.h, which has not been merged yet,
thus causing a dt_binding_check error on -next.

Fix this error by simply hardcoding the clock index in the example,
before the breakage spreads any further.

Fixes: dd71cd4d ("spi: Add Nuvoton WPCM450 Flash Interface Unit (FIU) bindings")
Reported-by: Rob Herring <robh@kernel.org>
Reported-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221129102225.3598044-2-j.neuschaefer@gmx.netSigned-off-by: Mark Brown <broonie@kernel.org>

If the device does not come straight from reset, we might receive an IRQ
before we are ready to handle it.

Fixes:

[    0.832328] Unable to handle kernel read from unreadable memory at virtual address 0000000000000010
[    1.040343] Call trace:
[    1.040347]  mtk_spi_can_dma+0xc/0x40
...
[    1.262265]  start_kernel+0x338/0x42c
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221128-spi-mt65xx-v1-0-509266830665@chromium.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The logical structures of mtk_nor_write_buffer_enable and
mtk_nor_write_buffer_disable are very similar, So it is necessary to
combine them into one.
Signed-off-by: bayi cheng <bayi.cheng@mediatek.com>
Link: https://lore.kernel.org/r/20221115124655.10124-1-bayi.cheng@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

The Intel SPI-NOR controller supports SFDP (Serial Flash Discoverable
Parameter) opcode so add it to the list of supported opcodes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221025064623.22808-5-mika.westerberg@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The SPI-NOR operation can have non-zero chip address as well so take
this into account in intel_spi_read/write_reg().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221025064623.22808-4-mika.westerberg@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

This allows us to get rid of the checks in the intel_spi_[sh]w_cycle()
and makes it possible for the SPI-NOR core to split the transaction into
smaller chunks as needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221025064623.22808-3-mika.westerberg@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

This way we do not need the SPI-NOR opcode -> Intel controller opcode
mapping in the function anymore.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221025064623.22808-2-mika.westerberg@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Linux 6.1-rc4 which should get my CI working on RPi3s again.

Merge series from Jonathan Neuschäfer <j.neuschaefer@gmx.net>:

This patchset adds DT bindings and a driver for the Flash Interface Unit
(FIU), the SPI flash controller in the Nuvoton WPCM450 BMC SoC. It
supports four chip selects, and direct (memory-mapped) access to 16 MiB
per chip. Larger flash chips can be accessed by software-defined SPI
transfers.

The existing NPCM7xx FIU driver is sufficitently incompatible with the
WPCM450 FIU that I decided to write a new driver.

Since commit 0166dc11 ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20221125083114.67e7f83c@endymion.delvareSigned-off-by: Mark Brown <broonie@kernel.org>

The Flash Interface Unit (FIU) is the SPI flash controller in the
Nuvoton WPCM450 BMC SoC. It supports four chip selects, and direct
(memory-mapped) access to 16 MiB per chip. Larger flash chips can be
accessed by software-defined SPI transfers.

The FIU in newer NPCM7xx SoCs is not compatible with the WPCM450 FIU.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221124191400.287918-2-j.neuschaefer@gmx.netSigned-off-by: Mark Brown <broonie@kernel.org>

Besides software controlled SPI transfers (UMA, "user mode access"), FIU
also supports a 16 MiB mapping window per attached flash chip.

This patch implements direct mapped read access, to speed up flash reads.

Without direct mapping:

	# time dd if=/dev/mtd0ro of=dump bs=1M
	16+0 records in
	16+0 records out
	real    1m 47.74s
	user    0m 0.00s
	sys     1m 47.75s

With direct mapping:

	# time dd if=/dev/mtd0ro of=dump bs=1M
	16+0 records in
	16+0 records out
	real    0m 30.81s
	user    0m 0.00s
	sys     0m 30.81s
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20221124191400.287918-4-j.neuschaefer@gmx.netSigned-off-by: Mark Brown <broonie@kernel.org>

The Flash Interface Unit (FIU) is the SPI flash controller in the
Nuvoton WPCM450 BMC SoC. It supports four chip selects, and direct
(memory-mapped) access to 16 MiB per chip. Larger flash chips can be
accessed by software-defined SPI transfers.

The FIU in newer NPCM7xx SoCs is not compatible with the WPCM450 FIU.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20221124191400.287918-3-j.neuschaefer@gmx.netSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Kunihiko Hayashi <hayashi.kunihiko@socionext.com>:

This series adds dt-bindings and a driver for Socionext F_OSPI controller
for connecting an SPI Flash memory over up to 8-bit wide bus.
The controller supports up to 4 chip selects.

Add devicetree binding documentation for Socionext F_OSPI SPI flash
controller.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221124003351.7792-2-hayashi.kunihiko@socionext.comSigned-off-by: Mark Brown <broonie@kernel.org>

Introduce Socionext F_OSPI controller driver. This controller is used to
communicate with slave devices such as SPI Flash memories. It supports
4 slave devices and up to 8-bit wide bus, but supports master mode only.

This driver uses spi-mem framework for SPI flash memory access, and
can only operate indirect access mode and single data rate mode.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221124003351.7792-3-hayashi.kunihiko@socionext.comSigned-off-by: Mark Brown <broonie@kernel.org>

The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-566-uwe@kleine-koenig.orgSigned-off-by: Mark Brown <broonie@kernel.org>

.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-565-uwe@kleine-koenig.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'i2c/client_device_id_helper-immutable' of https://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into spi-6.2

so we can use the new API in the I2C cleanup.

The at91 QSPI IP uses a default value of half of the period of the QSPI
clock period for the cs-setup time, which is not always enough, an example
being the sst26vf064b SPI NOR flash which requires a minimum cs-setup time
of 5 ns. It was observed that none of the at91 SoCs can fulfill the
minimum CS setup time for the aforementioned flash, as they operate at
high frequencies and half a period does not suffice for the required CS
setup time. Add support for configuring the CS timing in the controller.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-5-tudor.ambarus@microchip.comSigned-off-by: Mark Brown <broonie@kernel.org>

commit 4ccf3598 ("spi: remove spi_set_cs_timing()"), removed the
method as noboby used it. Nobody used it probably because some SPI
controllers use some default large cs-setup time that covers the usual
cs-setup time required by the spi devices. There are though SPI controllers
that have a smaller granularity for the cs-setup time and their default
value can't fulfill the spi device requirements. That's the case for the
at91 QSPI IPs where the default cs-setup time is half of the QSPI clock
period. This was observed when using an sst26vf064b SPI NOR flash which
needs a spi-cs-setup-ns = <7>; in order to be operated close to its maximum
104 MHz frequency.

Call spi_set_cs_timing() in spi_setup() just before calling spi_set_cs(),
as the latter needs the CS timings already set.
If spi->controller->set_cs_timing is not set, the method will return 0.
There's no functional impact expected for the existing drivers. Even if the
spi-mt65xx.c and spi-tegra114.c drivers set the set_cs_timing method,
there's no user for them as of now. The only tested user of this support
will be a SPI NOR flash that comunicates with the Atmel QSPI controller for
which the support follows in the next patches.

One will notice that this support is a bit different from the one that was
removed in commit 4ccf3598 ("spi: remove spi_set_cs_timing()"),
because this patch adapts to the changes done after the removal: the move
of the cs delays to the spi device, the retirement of the lelgacy GPIO
handling. The mutex handling was removed from spi_set_cs_timing() because
we now always call spi_set_cs_timing() in spi_setup(), which already
handles the spi->controller->io_mutex, so use the mutex handling from
spi_setup().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-4-tudor.ambarus@microchip.comSigned-off-by: Mark Brown <broonie@kernel.org>

SPI NOR flashes have specific cs-setup time requirements without which
they can't work at frequencies close to their maximum supported frequency,
as they miss the first bits of the instruction command. Unrecognized
commands are ignored, thus the flash will be unresponsive. Introduce the
spi-cs-setup-ns property to allow spi devices to specify their cs setup
time.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-3-tudor.ambarus@microchip.comSigned-off-by: Mark Brown <broonie@kernel.org>

SPI NOR flashes have specific cs-setup time requirements without which
they can't work at frequencies close to their maximum supported frequency,
as they miss the first bits of the instruction command. Unrecognized
commands are ignored, thus the flash will be unresponsive. Introduce the
spi-cs-setup-ns property to allow spi devices to specify their cs setup
time.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-2-tudor.ambarus@microchip.comSigned-off-by: Mark Brown <broonie@kernel.org>

Make the driver be able to bit-bang a GPIO for the Chip Select pin of
select peripherals.

The GPIO value is driven by the driver in that case, and none of the
hardware Chip Select bits will be populated in the PUSHR register for
the TX commands constructed for this peripheral.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20221111211356.545026-1-vladimir.oltean@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Introduces new helper function to aid in .probe_new() refactors. In order
to use existing i2c_get_device_id() on the probe callback, the device
match table needs to be accessible in that function, which would require
bigger refactors in some drivers using the deprecated .probe callback.

This issue was discussed in more detail in the IIO mailing list.

Link: https://lore.kernel.org/all/20221023132302.911644-11-u.kleine-koenig@pengutronix.de/Suggested-by: Nuno Sá <noname.nuno@gmail.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Angel Iglesias <ang.iglesiasg@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The timeout value of the current dma read is unreasonable. For example,
If the spi flash clock is 26Mhz, It will takes about 1.3ms to read a
4KB data in spi mode. But the actual measurement exceeds 50s when a
dma read timeout is encountered.

In order to be more accurately, It is necessary to use usecs_to_jiffies,
After modification, the measured timeout value is about 130ms.
Signed-off-by: bayi cheng <bayi.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221114081327.25750-1-bayi.cheng@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Pull cxl fixes from Dan Williams:
 "Several fixes for CXL region creation crashes, leaks and failures.

  This is mainly fallout from the original implementation of dynamic CXL
  region creation (instantiate new physical memory pools) that arrived
  in v6.0-rc1.

  Given the theme of "failures in the presence of pass-through decoders"
  this also includes new regression test infrastructure for that case.

  Summary:

   - Fix region creation crash with pass-through decoders

   - Fix region creation crash when no decoder allocation fails

   - Fix region creation crash when scanning regions to enforce the
     increasing physical address order constraint that CXL mandates

   - Fix a memory leak for cxl_pmem_region objects, track 1:N instead of
     1:1 memory-device-to-region associations.

   - Fix a memory leak for cxl_region objects when regions with active
     targets are deleted

   - Fix assignment of NUMA nodes to CXL regions by CFMWS (CXL Window)
     emulated proximity domains.

   - Fix region creation failure for switch attached devices downstream
     of a single-port host-bridge

   - Fix false positive memory leak of cxl_region objects by recycling
     recently used region ids rather than freeing them

   - Add regression test infrastructure for a pass-through decoder
     configuration

   - Fix some mailbox payload handling corner cases"

* tag 'cxl-fixes-for-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
  cxl/region: Recycle region ids
  cxl/region: Fix 'distance' calculation with passthrough ports
  tools/testing/cxl: Add a single-port host-bridge regression config
  tools/testing/cxl: Fix some error exits
  cxl/pmem: Fix cxl_pmem_region and cxl_memdev leak
  cxl/region: Fix cxl_region leak, cleanup targets at region delete
  cxl/region: Fix region HPA ordering validation
  cxl/pmem: Use size_add() against integer overflow
  cxl/region: Fix decoder allocation crash
  ACPI: NUMA: Add CXL CFMWS 'nodes' to the possible nodes set
  cxl/pmem: Fix failure to account for 8 byte header for writes to the device LSA.
  cxl/region: Fix null pointer dereference due to pass through decoder commit
  cxl/mbox: Add a check on input payload size

Merge tag 'hwmon-for-v6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
 "Fix two regressions:

   - Commit 54cc3dbf ("hwmon: (pmbus) Add regulator supply into
     macro") resulted in regulator undercount when disabling regulators.
     Revert it.

   - The thermal subsystem rework caused the scmi driver to no longer
     register with the thermal subsystem because index values no longer
     match. To fix the problem, the scmi driver now directly registers
     with the thermal subsystem, no longer through the hwmon core"

* tag 'hwmon-for-v6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  Revert "hwmon: (pmbus) Add regulator supply into macro"
  hwmon: (scmi) Register explicitly with Thermal Framework

Pull perf fixes from Borislav Petkov:

 - Add Cooper Lake's stepping to the PEBS guest/host events isolation
   fixed microcode revisions checking quirk

 - Update Icelake and Sapphire Rapids events constraints

 - Use the standard energy unit for Sapphire Rapids in RAPL

 - Fix the hw_breakpoint test to fail more graciously on !SMP configs

* tag 'perf_urgent_for_v6.1_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Add Cooper Lake stepping to isolation_ucodes[]
  perf/x86/intel: Fix pebs event constraints for SPR
  perf/x86/intel: Fix pebs event constraints for ICL
  perf/x86/rapl: Use standard Energy Unit for SPR Dram RAPL domain
  perf/hw_breakpoint: test: Skip the test if dependencies unmet

Pull x86 fixes from Borislav Petkov:

 - Add new Intel CPU models

 - Enforce that TDX guests are successfully loaded only on TDX hardware
   where virtualization exception (#VE) delivery on kernel memory is
   disabled because handling those in all possible cases is "essentially
   impossible"

 - Add the proper include to the syscall wrappers so that BTF can see
   the real pt_regs definition and not only the forward declaration

* tag 'x86_urgent_for_v6.1_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Add several Intel server CPU model numbers
  x86/tdx: Panic on bad configs that #VE on "private" memory access
  x86/tdx: Prepare for using "INFO" call for a second purpose
  x86/syscall: Include asm/ptrace.h in syscall_wrapper header

Merge tag 'kbuild-fixes-v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Use POSIX-compatible grep options

 - Document git-related tips for reproducible builds

 - Fix a typo in the modpost rule

 - Suppress SIGPIPE error message from gcc-ar and llvm-ar

 - Fix segmentation fault in the menuconfig search

* tag 'kbuild-fixes-v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: fix segmentation fault in menuconfig search
  kbuild: fix SIGPIPE error message for AR=gcc-ar and AR=llvm-ar
  kbuild: fix typo in modpost
  Documentation: kbuild: Add description of git for reproducible builds
  kbuild: use POSIX-compatible grep option

Pull kvm fixes from Paolo Bonzini:
"ARM:

   - Fix the pKVM stage-1 walker erronously using the stage-2 accessor

   - Correctly convert vcpu->kvm to a hyp pointer when generating an
     exception in a nVHE+MTE configuration

   - Check that KVM_CAP_DIRTY_LOG_* are valid before enabling them

   - Fix SMPRI_EL1/TPIDR2_EL0 trapping on VHE

   - Document the boot requirements for FGT when entering the kernel at
     EL1

  x86:

   - Use SRCU to protect zap in __kvm_set_or_clear_apicv_inhibit()

   - Make argument order consistent for kvcalloc()

   - Userspace API fixes for DEBUGCTL and LBRs"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: Fix a typo about the usage of kvcalloc()
  KVM: x86: Use SRCU to protect zap in __kvm_set_or_clear_apicv_inhibit()
  KVM: VMX: Ignore guest CPUID for host userspace writes to DEBUGCTL
  KVM: VMX: Fold vmx_supported_debugctl() into vcpu_supported_debugctl()
  KVM: VMX: Advertise PMU LBRs if and only if perf supports LBRs
  arm64: booting: Document our requirements for fine grained traps with SME
  KVM: arm64: Fix SMPRI_EL1/TPIDR2_EL0 trapping on VHE
  KVM: Check KVM_CAP_DIRTY_LOG_{RING, RING_ACQ_REL} prior to enabling them
  KVM: arm64: Fix bad dereference on MTE-enabled systems
  KVM: arm64: Use correct accessor to parse stage-1 PTEs

Pull xen fixes from Juergen Gross:
 "One fix for silencing a smatch warning, and a small cleanup patch"

* tag 'for-linus-6.1-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  x86/xen: simplify sysenter and syscall setup
  x86/xen: silence smatch warning in pmu_msr_chk_emulated()

Pull ext4 fixes from Ted Ts'o:
 "Fix a number of bugs, including some regressions, the most serious of
  which was one which would cause online resizes to fail with file
  systems with metadata checksums enabled.

  Also fix a warning caused by the newly added fortify string checker,
  plus some bugs that were found using fuzzed file systems"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix fortify warning in fs/ext4/fast_commit.c:1551
  ext4: fix wrong return err in ext4_load_and_init_journal()
  ext4: fix warning in 'ext4_da_release_space'
  ext4: fix BUG_ON() when directory entry has invalid rec_len
  ext4: update the backup superblock's at the end of the online resize

Pull cifs fixes from Steve French:
 "One symlink handling fix and two fixes foir multichannel issues with
  iterating channels, including for oplock breaks when leases are
  disabled"

* tag '6.1-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix use-after-free on the link name
  cifs: avoid unnecessary iteration of tcp sessions
  cifs: always iterate smb sessions using primary channel

Pull `lTracing fixes for 6.1-rc3:

 - Fixed NULL pointer dereference in the ring buffer wait-waiters code
   for machines that have less CPUs than what nr_cpu_ids returns.

   The buffer array is of size nr_cpu_ids, but only the online CPUs get
   initialized.

 - Fixed use after free call in ftrace_shutdown.

 - Fix accounting of if a kprobe is enabled

 - Fix NULL pointer dereference on error path of fprobe rethook_alloc().

 - Fix unregistering of fprobe_kprobe_handler

 - Fix memory leak in kprobe test module

* tag 'trace-v6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  tracing: kprobe: Fix memory leak in test_gen_kprobe/kretprobe_cmd()
  tracing/fprobe: Fix to check whether fprobe is registered correctly
  fprobe: Check rethook_alloc() return in rethook initialization
  kprobe: reverse kp->flags when arm_kprobe failed
  ftrace: Fix use-after-free for dynamic ftrace_ops
  ring-buffer: Check for NULL cpu_buffer in ring_buffer_wake_waiters()