ioatdma by default is in snoop mode. Relaxed ordering according to spec
does not do anything in snoop mode. However, it causes hang or significant
performance degrade when tested with NTB. Disabling in the driver due to
some BIOS do not configure it correctly.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Currently the following DT description would result in dmac0 always
being tried first and dmac1 second if dmac0 was unavailable. This
results in heavier use of dmac0 then of dmac1. This patch adds an
approximate average distribution over the two nodes lessening the load
of anyone of them.

   i2c6: i2c@e60b0000 {
           ...
           dmas = <&dmac0 0x77>, <&dmac0 0x78>,
                  <&dmac1 0x77>, <&dmac1 0x78>;
           dma-names = "tx", "rx", "tx", "rx";
           ...
   };
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

When the ccerr handler is called but the error registers indicate no error
events we need to command eDMA to re-evaluate the errors. Otherwise we can
receive flood of error interrupts.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

In order to create a relationship model between the channels and the
management object, we are adding support for object hierarchy to the
drivers. This patch simplifies the userspace application development.
We will not have to traverse different firmware paths based on device
tree or ACPI based kernels.

No matter what flavor of kernel is used, objects will be represented as
platform devices.

The new layout is as follows:

hidmam_10: hidma-mgmt@0x5A000000 {
	compatible = "qcom,hidma-mgmt-1.0";
	...

	hidma_10: hidma@0x5a010000 {
			compatible = "qcom,hidma-1.0";
			...
	}
}

The hidma_mgmt_init detects each instance of the hidma-mgmt-1.0 objects
in device tree and calls into the channel driver to create platform devices
for each child of the management object.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Add debugfs hooks for debugging the execution behavior of the DMA
channel. The debugfs hooks get initialized by the probe function and
uninitialized by the remove function.

A stats file is created in debugfs. The stats file will show the
information about each HIDMA channel as well as each asynchronous job
queued and completed at a given time.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch implements the hardware hooks for the HIDMA channel driver.

The main functions of interest are:
- hidma_ll_init
- hidma_ll_request
- hidma_ll_queue_request
- hidma_ll_hw_start

OS layer calls the hidma_ll_init function during probe to set up the
hardware. At this moment, the number of supported descriptors are also
given. On each request, a descriptor is allocated from the free pool and
filled in with the transfer parameters. Multiple requests can be queued
into the hardware via the OS interface. When client is ready for requests
to be executed, start method is called.

Completions are delivered via callbacks via tasklet.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Added basic clock support for axi dma's.
The clocks are requested at probe and released at remove.
Reviewed-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch updates the binding doc with clock description
for AXI DMA's.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch adds config structure in the driver to differentiate
AXI DMA's and to add more features(clock support etc..) to these DMA's.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Update the Tegra DMA driver maintainer field to include the newly added
Tegra210 ADMA and add Jon Hunter as a co-maintainer for Tegra DMA.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Add support for the Tegra210 Audio DMA controller that is used for
transferring data between system memory and the Audio sub-system.
The driver only supports cyclic transfers because this is being solely
used for audio.

This driver is based upon the work by Dara Ramesh <dramesh@nvidia.com>.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Add device-tree binding documentation for the Tegra210 Audio DMA
controller.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch adds support for the AXI Central Direct Memory Access
(AXI CDMA) core to the existing vdma driver, AXI CDMA is a
soft Xilinx IP core that provides high-bandwidth
Direct Memory Access(DMA) between a memory-mapped
source address and a memory-mapped destination address.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch updates the device-tree binding doc for
adding support for AXI CDMA.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch adds support for the AXI Direct Memory Access (AXI DMA)
core in the existing vdma driver, AXI DMA Core is a
soft Xilinx IP core that provides high-bandwidth
direct memory access between memory and AXI4-Stream
type target peripherals.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch updates the device-tree binding doc for
adding support for AXI DMA.
Also this patch differentiates required properties b/w
DMA and VDMA.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch renames the xilinx_vdma_ prefix to xilinx_dma
for the API's and masks that will be shared b/w three DMA
IP cores.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

When check for capabilities recognize slave support by either DMA_SLAVE or
DMA_CYCLIC bit set. If we don't do that the user can't get a normally worked
DMA support for engines that doesn't have one of the mentioned bits set.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Armada 3700 SoC uses the mv_xor driver but don't select anymore the
PLAT_ORION symbol. This commit extends the dependency of the mv_xor
driver to the more modern SoCs only compatible with ARCH_MVEBU, which
allows using it with the Armada 3700 SoC.

In the same time it also add the COMPILE_TEST dependency allowing a wider
test coverage.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Armada 3700 SoC comprise a single XOR engine compliant with the ones used
in older Marvell SoC's like Armada XP or 38x. The only thing that needs
modification is the Mbus configuration, which has to be done on two
levels: global and in device. The first one is inherited from the
bootloader. The latter can be opened in a default way, leaving
arbitration to the bus controller. Hence filled mbus_dram_target_info
structure is not needed.

Patch "dmaengine: mv_xor: optimize performance by using a subset
of the XOR channels" introduced limitation for using XOR engines and
channels vs number of available CPU's. Those constraints do not however
fit Armada 3700 architecture with two possible CPU's and single,
dual-channel engine. Hence in this commit an adjustment for setting
maximum available channels is added.

This patch enables XOR access to DRAM by opening default window to 4GB
space with specific attribute.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Currently the main difference between legacy XOR engine and newer one, is
the way the engine modes are setup (either in the descriptor or through
the controller registers). In order to be able to take into account new
generation of the XOR engine for the ARM64 SoC, we need to identify them
by type, and then depending to the type the engine setup will be
selected.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Fix two warnings which appear when building for 64 bits target:

drivers/dma/mv_xor.c: In function ‘mv_xor_prep_dma_xor’:
drivers/dma/mv_xor.c:480:3: warning: format ‘%u’ expects argument of type ‘unsigned int’, but argument 6 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
   "%s src_cnt: %d len: %u dest %pad flags: %ld\n",
   ^
drivers/dma/mv_xor.c: In function ‘mv_xor_probe’:
drivers/dma/mv_xor.c:1223:17: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
    op_in_desc = (int)of_id->data;
                 ^
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Dma_pool_zalloc combines dma_pool_alloc and memset 0.  The semantic patch
that makes this transformation is as follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression d,e;
statement S;
@@

        d =
-            dma_pool_alloc
+            dma_pool_zalloc
             (...);
        if (!d) S
-       memset(d, 0, sizeof(*d));
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Dma_pool_zalloc combines dma_pool_alloc and memset 0.  The semantic patch
that makes this transformation is as follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression d,e;
statement S;
@@

        d =
-            dma_pool_alloc
+            dma_pool_zalloc
             (...);
        if (!d) S
-       memset(d, 0, sizeof(*d));
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Dma_pool_zalloc combines dma_pool_alloc and memset 0.  The semantic patch
that makes this transformation is as follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression d,e;
statement S;
@@

        d =
-            dma_pool_alloc
+            dma_pool_zalloc
             (...);
        if (!d) S
-       memset(d, 0, sizeof(*d));
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Dma_pool_zalloc combines dma_pool_alloc and memset 0.  The semantic patch
that makes this transformation is as follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression d,e;
statement S;
@@

        d =
-            dma_pool_alloc
+            dma_pool_zalloc
             (...);
        if (!d) S
-       memset(d, 0, sizeof(*d));
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

DMA cyclic transfers are required by audio streaming.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>