Revision 2 of LCDC suffers from an issue where a SYNC_LOST error
caused by limited memory bandwidth may leave the picture shifted a
couple pixels to the right.

This issue has not been observed on revision 1, while the recovery
mechanism introduces a different issue, where the END_OF_FRAME
interrupt doesn't fire while drm is waiting for vblanks.

On rev1: recover from sync lost errors by simply clearing the
RASTER_ENABLE bit in the RASTER_CTRL register and re-enabling it
again as is suggested by the datasheet.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>

The DT binding for tildc is not consistent with the driver code: there
are two options - 'max-width' and 'max-pixelclock' specified in the
documentation which are parsed as 'ti,max-width' and
'ti,max-pixelclock' respectively.

Make the driver code consistent with the binding.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>

We should wait for the last frame to complete before shutting things
down also on LCDC rev 1.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Configure video mode to HW in enable() call back. There is no reason
to do it before that. This makes PM functions way easier because there
is no HW context to save when screen is for instance blanked. This
patch removes mode_set_nofb() call back from tilcdc.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Load palette at the end of mode_set_nofb(). Moving the palette loading
to mode_set_nofb() saves us from storing and restoring of framebuffer
addresses in dma registers that were just recently written there.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Add timeout wait for palette loadind to complete. We do not want to
hang forever if palette loaded interrupt does not arrive for some
reason.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

The LCDC revision 2 documentation also mentions the mandatory palette
for true color modes. Even if the rev 2 LCDC appears to work just fine
without the palette being loaded loading it helps in testing the
feature.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Set LCDC_PALETTE_LOAD_MODE bit-field with new tilcdc_write_mask()
instead of tilcdc_set(). Setting a bit-fields with tilcdc_set() is
fundamentally broken.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Add tilcdc_write_mask() for handling register field wider than one bit
and mask values for those fields.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Failed tilcdc_crtc_create() error handling was broken, this patch
should fix it.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Revision 1 of the IP doesn't work if we don't load the palette (even
if it's not used, which is the case for the RGB565 format).

Add a function called from tilcdc_crtc_enable() which performs all
required actions if we're dealing with a rev1 chip.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Revision 1 LCDC support also sync lost errors and can benefit from
sync lost recovery routine.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Adds drm bride support for attaching drm bridge drivers to tilcdc. The
decision whether a video port leads to an external encoder or bridge
is made simply based on remote device's compatible string. The code
has been tested with BeagleBone-Black with and without BeagleBone
DVI-D Cape Rev A3 using ti-tfp410 driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Add very basic ti-tfp410 DVI transmitter driver. The only feature
separating this from a completely dummy bridge is the EDID read
support trough DDC I2C. Even that functionality should be in a
separate generic connector driver. However, because of missing DRM
infrastructure support the connector is implemented within the bridge
driver. Some tfp410 HW specific features may be added later if needed,
because there is a set of registers behind i2c if it is connected.

This implementation is tested against my new tilcdc bridge support
and it works with BeagleBone DVI-D Cape Rev A3. A DT binding document
is also updated.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Rob Herring <robh@kernel.org>

Move "ti,tfp410.txt" from display/ti to display/bridge before adding
generic (non omapdrm/dss specific) implementation and new features.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Rob Herring <robh@kernel.org>

Recover from sync lost error flood by resetting the LCDC instead of
turning off the SYNC_LOST error IRQ. When LCDC starves on limited
memory bandwidth it may sometimes result an error situation when the
picture may have shifted couple of pixels to right and SYNC_LOST
interrupt is generated on every frame. LCDC main reset recovers from
this situation and causes a brief blanking on the screen.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Fix race from forced shutdown of crtc in unload by adding internal
locking and a boolean telling if device is going to be shutdown.
Signed-off-by: Jyri Sarha <jsarha@ti.com>

Use unload to handle initialization failures instead of complex goto
label mess. To do this the initialization sequence needed slight
reordering and some unload functions needed to become conditional.
Signed-off-by: Jyri Sarha <jsarha@ti.com>

Stop using struct drm_driver load() and unload() callbacks. The
callbacks should not be used anymore. Instead of using load the
drm_device is allocated with drm_dev_alloc() and registered with
drm_dev_register() only after the driver is completely initialized.
The deinitialization is done directly either in component unbind
callback or in platform driver demove callback.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Remove obsolete drm_connector_register() calls from tilcdc_panel.c and
tilcdc_tfp410.c. All connectors are registered when drm_dev_register()
is called.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

This error message will be printed when a FIFO underflow irq has
triggered. Since this happens sometimes and the error message will be
displayed on the console, it should have a correct spelling.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Jyri Sarha <jsarha@ti.com>

The commit d8ff0c63fbcb ("drm/tilcdc: Adjust the FB_CEILING address")
added an adjustment of the FB_CEILING address. This is done by decrementing
the address by one.

On the AM335x (rev 0x4F201000) the framebuffer is rotated left over the
display border, because the ceiling address is 8f276fff instead of
8f277000. Since this adjustment isn't necessary for the LCDC v2, the
origin ceiling address should be used.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Jyri Sarha <jsarha@ti.com>

Due to some potential tweaks for the da850 LCDC (for example: the
required memory bandwith settings) we need a separate compatible
for the IP present on the da850 boards.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jyri Sarha <jsarha@ti.com>

Some architectures don't use the common clock framework and don't
implement all the clk interfaces for every clock. This is the case
for da850-lcdk where clk_set_rate() only works for PLL0 and PLL1.

Trying to set the clock rate for the LCDC clock results in -EINVAL
being returned.

As a workaround for that: if the call to clk_set_rate() fails, fall
back to adjusting the clock divider instead. Proper divider value is
calculated by dividing the current clock rate by the required pixel
clock rate in HZ.

This code is based on a hack initially developed internally for
baylibre by Karl Beldan <kbeldan@baylibre.com>.

Tested with a da850-lcdk with an LCD display connected over VGA.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>

These updates:
* improve the robustness of the driver wrt races
* improve the compliance for sending infoframes and audio
* re-organise the function order in the driver to group like functions
  together.  (This unfortunately causes a conflict with the change in
  drm-misc, but it should be trivial to solve, although it looks more
  scarey than it really is - sfr has already sent two reports about
  this, one earlier today.)
* simplify tda998x_audio_get_eld and DPMS handling
* power down sections of the chip that we never use
* add some initial preparation for supporting the CEC driver

* 'drm-tda998x-devel' of git://git.armlinux.org.uk/~rmk/linux-arm:
  drm/i2c: tda998x: fix spelling mistake
  drm/i2c: tda998x: allow sharing of the CEC device accesses
  drm/i2c: tda998x: allow interrupt to be shared
  drm/i2c: tda998x: power down pre-filter and color conversion
  drm/i2c: tda998x: switch to boolean is_on
  drm/i2c: tda998x: remove complexity from tda998x_audio_get_eld()
  drm/i2c: tda998x: group audio functions together
  drm/i2c: tda998x: separate connector initialisation
  drm/i2c: tda998x: group connector functions and funcs together
  drm/i2c: tda998x: move and rename tda998x_encoder_set_config()
  drm/i2c: tda998x: correct function name in comments
  drm/i2c: tda998x: only enable audio if supported by sink
  drm/i2c: tda998x: only configure infoframes and audio if supported
  drm/i2c: tda998x: avoid race when programming audio
  drm/i2c: tda998x: avoid racy access to mode clock
  drm/i2c: tda998x: avoid race in tda998x_encoder_mode_set()
  drm/i2c: tda998x: move audio mutex initialisation

Building on top of the MALI change previously merged, these changes:
* add tracing support for overlay updates
* refactor some of the plane support code
* de-midlayer the driver
* cleanups from other folk reviewing the code

* 'drm-armada-devel' of git://git.armlinux.org.uk/~rmk/linux-arm:
  drm/armada: fix NULL pointer comparison warning
  drm/armada: use DRM_FB_HELPER_DEFAULT_OPS for fb_ops
  drm/armada: remove some dead code
  drm/armada: mark symbols static where possible
  drm/armada: de-midlayer armada
  drm/armada: use common helper for plane base address
  drm/armada: move setting primary plane position to armada_drm_primary_set()
  drm/armada: split out primary plane update
  drm/armada: move plane state to struct armada_plane
  drm/armada: clean up armada_drm_plane_work_run()
  drm/armada: add tracing support

hibmc drm driver for hisilicon.

* tag 'drm-hisilicon-next-2016-11-17' of http://github.com/zourongrong/linux:
  MAINTAINERS: Update HISILICON DRM entries
  drm/hisilicon/hibmc: Add support for vblank interrupt
  drm/hisilicon/hibmc: Add support for VDAC
  drm/hisilicon/hibmc: Add support for display engine
  drm/hisilicon/hibmc: Add support for frame buffer
  drm/hisilicon/hibmc: Add video memory management
  drm/hisilicon/hibmc: Add hisilicon hibmc drm master driver

Trivial fix to spelling mistake "configutation" to "configuration"
in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

cec_read() is non-atomic in the presence of other I2C bus transactions
to the same device.  This presents a problem when we add support for
the TDA9950 CEC engine part - both drivers can be trying to access the
device.

Avoid the inherent problems by switching to i2c_transfer() instead,
which allows us to perform more than one bus transaction atomically.

As this means we will be using I2C transactions rather than SMBUS, we
have to check that the host supports I2C functionality.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Some TDA998x contain several different I2C devices - there is the HDMI
encoder, and there is a TDA9950 CEC engine.  These two share the same
interrupt signal.

In order to allow a driver for the CEC engine to work, we need to be
able to share the interrupt with the CEC driver, so convert the handler
and registration to allow this to happen.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Disabling the pre-filter block of the TDA998x saves 40mW and the colour
conversion block saves 15mW.  As we always disable these two blocks, we
can power these sections of the chip down to save 55mW of unnecessary
power consumption.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Rather than storing the DPMS mode (which will always be on or off) use a
boolean to store this instead.
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

tda998x_audio_get_eld() is needlessly complex - the connector associated
with the encoder is always our own priv->connector.  Remove this
complexity, but ensure that there are no races when copying out the ELD.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Group the TDA998x audio functions together rather than split between
two different locations in the file, keeping like code together.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Separate out the connector initialisation from the rest of the drivers
initialisation.
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Group the TDA998x connector functions and funcs structures together
before the encoder support, rather than scattered amongst the rest of
the file.  This keeps like code together.
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

The naming of tda998x_encoder_set_config() is a left-over from when
TDA998x was a slave encoder.  Since this is part of the initialisation,
drop the _encoder from the name, and move it near tda998x_bind().
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Correct two references to tda998x_connector_get_modes() which were
incorrectly referring to tda998x_encoder_get_modes().
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Check for audio support by the attached sink by consulting the EDID
prior to enabling audio over the TMDS link.  We must consult the EDID
after calling drm_helper_probe_single_connector_modes(), as this can
use an override EDID, or load a replacement EDID.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

The CEA 861B specification indicates the situations when we are able to
send each infoframe based on the version of the EDID's CEA extension.
Update the tda998x driver to follow the CEA specification wrt sending
of infoframes.

Since we only support the generation of AVI version 2, this limits us
to CEA extension version 3, so we treat CEA extension version 2 as
CEA 861 (no infoframes, no audio.)
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>