It's possible some configurations would prevent driver from utilizing
all the Memory Regions due to a lack of ILT lines.
In such a case, calculate how many memory regions would have to be
dropped due to limit, and manage without those.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As RoCE doesn't need to use the SRC, allocating ILT memory
on behalf of RoCE is wasting available ILT lines.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As of today there's no protocol supported that requires
support from the TM hardware block and enables SRIOV,
but we should still correct the calculation to reflect
the lines required for such future VFs instead of changing
the PF's own lines.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When configuring the HW timers block we should set the number of CIDs
up until the last CID that require timers, instead of only those CIDs
whose protocol needs timers support.

Today, the protocols that require HW timers' support have their CIDs
before any other protocol, but that would change in future [when we
add iWARP support].
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor and clean up the queue manager initialization logic.
Also, this adds support for RoC low latency queues, which later
would be used for improving RoCE latency in high throughput scenarios.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the net stats64 counters to the usbnet core. With that
in place put the hooks into every usbnet driver to use it.

This is a strait forward addition of 64bit counters for RX and TX packet
and byte counts. It is done in the same style as for the other net drivers
that support stats64. Note that the other stats fields remain as 32bit
sized values (error counts, etc).

The motivation to add this is that it is not particularly difficult to
get the RX and TX byte counts to wrap on 32bit platforms.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Number of sockets is limited by 16-bit, so 64-bit allocation will never
happen.

16-bit ops are the worst code density-wise on x86_64 because of
additional prefix (66).

Space savings:

	add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-3 (-3)
	function                                     old     new   delta
	reuseport_add_sock                           539     536      -3
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make ->hash_count, ->low_watermark and ->high_watermark unsigned int
and propagate unsignedness to other variables.

This change doesn't change code generation because these fields aren't
used in 64-bit contexts but make it anyway: these fields can't be
negative numbers.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hash size can't negative so "unsigned int" is logically correct.

Propagate "unsigned int" to loop counters.

Space savings:

	add/remove: 0/0 grow/shrink: 2/2 up/down: 6/-18 (-12)
	function                                     old     new   delta
	flow_cache_flush_tasklet                     362     365      +3
	__flow_cache_shrink                          333     336      +3
	flow_cache_cpu_up_prep                       178     171      -7
	flow_cache_lookup                           1159    1148     -11
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Flow keys aren't 4GB+ numbers so 64-bit arithmetic is excessive.

Space savings (I'm not sure what CSWTCH is):

	add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-48 (-48)
	function                                     old     new   delta
	flow_cache_lookup                           1163    1159      -4
	CSWTCH                                     75997   75953     -44
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Breaking the include loop netdevice.h, dsa.h, devlink.h broke this
driver, it depends on includes brought in by these headers. Adding
linux/of.h fixes it.

Fixes: ed0e39e97d34 ("net: break include loop netdevice.h, dsa.h, devlink.h")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an incoming frame is tagged or when GRO is disabled, the skb
handled to vxlan_xmit() doesn't contain a valid transport header
offset. This makes ND proxying fail.

We combine two changes: replace use of skb_transport_offset() and ensure
the necessary amount of skb is linear just before using it:

 - In vxlan_xmit(), when determining if we have an ICMPv6 neighbor
   discovery packet, just check if it is an ICMPv6 packet and rely on
   neigh_reduce() to do more checks if this is the case. The use of
   pskb_may_pull() is replaced by skb_header_pointer() for just the IPv6
   header.

 - In neigh_reduce(), add pskb_may_pull() for IPv6 header and neighbor
   discovery message since this was removed from vxlan_xmit(). Replace
   skb_transport_header() with ipv6_hdr() + 1.

 - In vxlan_na_create(), replace first skb_transport_offset() with
   ipv6_hdr() + 1 and second with skb_network_offset() + sizeof(struct
   ipv6hdr). Additionally, ensure we pskb_may_pull() the whole skb as we
   need it to iterate over the options.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before when implementing sctp prsctp, SCTP_PR_STREAM_STATUS wasn't
added, as it needs to save abandoned_(un)sent for every stream.

After sctp stream reconf is added in sctp, assoc has structure
sctp_stream_out to save per stream info.

This patch is to add SCTP_PR_STREAM_STATUS by putting the prsctp
per stream statistics into sctp_stream_out.

v1->v2:
  fix an indent issue.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Salil Mehta says:

====================
net: hns: Misc. HNS Bug Fixes & Code Improvements

This patch set introduces various HNS bug fixes, optimizations and code
improvements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes some checkpatch.pl script caught errors and
warnings during the compilation time.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a bug on Hip06 that tx ring interrupts packets count will be
clear when drivers send data to tx ring, so that the tx packets count
will never upgrade to packets line, and cause the interrupts engendered
was delayed.
Sometimes, it will cause sending performance lower than expected.

To fix this bug, we set tx ring interrupts packets line to 1 forever,
to avoid count clear. And set the gap time to 20us, to solve the problem
that too many interrupts engendered when packets line is 1.

This patch could advance the send performance on ARM  from 6.6G to 9.37G
when an iperf send thread on ARM and an iperf send thread on X86 for XGE.
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HNS needs SMB Buffers to store at least two packets after sending
pause frame because of the link delay. The MTU of HNS is 9728. As
the processor user manual described, the SBM buffer threshold should
be modified.
Reported-by: Ping Zhang <zhangping5@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to free all ppe submodule if it fails to initialize ppe by
any fault, so this patch will free all ppe resource before
hns_ppe_init() returns exception situation
Reported-by: JinchuanTian <tianjinchuan1@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the code to clear pclint warning/info.
Reported-by: Ping Zhang <zhangping5@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleans the redundant code from  hns_mdio.c.
Reported-by: Ping Zhang <zhangping5@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes redundant functions used only for debugging
purposes.
Reported-by: Weiwei Deng <dengweiwei@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a mac_id in mac control block structure, so the callback
function mac_get_id() is useless. Here we remove this function.
Reported-by: Weiwei Deng <dengweiwei@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The functions (hns_dsaf_set_mac_mc_entry() and hns_mac_del_mac()) are
not called by any functions. They are dead code in hns. And the same
features are implemented by the patch (the id is 66355f52).
Reported-by: Weiwei Deng <dengweiwei@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes below ethtool configuration error:

localhost:~ # ethtool -X eth0 hkey XX:XX:XX...
Cannot set Rx flow hash configuration: Operation not supported
Signed-off-by: lipeng <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netif_tx_lock is a global spin lock, it will take affect
in all rings in the netdevice. In tx_poll_one process, it can
only lock the current ring, in this case, we define a spin lock
in hnae_ring struct for it.
Signed-off-by: lipeng <lipeng321@huawei.com>
reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because buf_size of ring set to 2048, the process of rx_poll_one
can reuse the page, therefore the performance of XGE can improve.
But the chip only supports three bds in one package, so the max mtu
is 6K when it sets to 2048. For better performane in litter mtu, we
need change buf_size according to mtu.

When user change mtu, hns is only change the desc in memory. There
are some desc has been fetched by the chip, these desc can not be
changed by the code. So it needs set the port loopback and send
some packages to let the chip consumes the wrong desc and fetch new
desc.
Because the Pv660 do not support rss indirection, we need add version
check in mtu change process.
Signed-off-by: lipeng <lipeng321@huawei.com>
reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After polling less than buget packages, we need check again. If
there are still some packages, we call napi_schedule add softirq
queue, this is not better way. So we return buget value instead
of napi_schedule.
Signed-off-by: lipeng <lipeng321@huawei.com>
reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When run ethtool ethX on hns driver, the speed will show
as "Unknown". The base.speed is not correct assigned,
this patch fix this bug.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because all members of desc_cb is assigned when xmit one package, so it
can delete in hnae_free_buffer, as follows:
        - "dma, priv, length, type" are assigned in fill_v2_desc.
        - "page_offset, reuse_flag, buf" are not used in tx direction.
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Weiwei Deng <dengweiwei@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch optimises the init configuration code leg
for gmac pad and crc set interface.
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: JinchuanTian <tianjinchuan1@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch reduces GMAC TX threshold value to avoid gmac
hang-up with speed 100M/duplex half.
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: JinchuanTian <tianjinchuan1@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the implementation of the IRQ affinity
function. This function is used to create the cpu mask
which eventually is used to initialize the cpu<->queue
association for XPS(Transmit Packet Steering).
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sowmini Varadhan says:

====================
rds: tcp: couple of minor bug fixes

A couple of minor bugfixes that showed up during testing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The rds_connect_worker() has a bug in the check that enforces the
canonical connection order described in the comments of
rds_tcp_state_change(). The intention is to make sure that all
the multipath connections are always initiated by the smaller IP
address via rds_start_mprds. To achieve this, rds_connection_worker
should check that cp_index > 0.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rds: tcp: allow progress of rds_conn_shutdown if the rds_connection is marked ERROR by an intervening FIN

rds_conn_shutdown() runs in workq context, and marks the rds_connection
as DISCONNECTING before quiescing Tx/Rx paths. However, after all I/O
has quiesced, we may still find the rds_connection state to be
RDS_CONN_ERROR if an intervening FIN was processed in softirq context.

This is not a fatal error: rds_conn_shutdown() should continue the
shutdown, and there is no need to log noisy messages about this event.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It seems the code does not match the intent.

This broke packetdrill, and probably other programs.

Fixes: 6c7c98ba ("sock: avoid dirtying sk_stamp, if possible")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c: In function 'mlx5e_set_rxfh':
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c:1067: error: unknown field 'rss' specified in initializer
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c:1067: warning: missing braces around initializer
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c:1067: warning: (near initialization for 'rrp.<anonymous>')
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c:1068: error: unknown field 'rss' specified in initializer
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c:1069: warning: excess elements in struct initializer
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c:1069: warning: (near initialization for 'rrp')

gcc-4.4.4 has issues with anonymous union initializers.  Work around this.

Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/mellanox/mlx5/core/en_main.c: In function 'mlx5e_redirect_rqts':
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:2210: error: unknown field 'rqn' specified in initializer
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:2211: warning: missing braces around initializer
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:2211: warning: (near initialization for 'direct_rrp.<anonymous>')
drivers/net/ethernet/mellanox/mlx5/core/en_main.c: In function 'mlx5e_redirect_rqts_to_channels':
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:2227: error: unknown field 'rss' specified in initializer
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:2227: warning: missing braces around initializer
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:2227: warning: (near initialization for 'rrp.<anonymous>')
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:2227: warning: initialization makes integer from pointer without a cast
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:2228: error: unknown field 'rss' specified in initializer
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:2229: warning: excess elements in struct initializer
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:2229: warning: (near initialization for 'rrp')
drivers/net/ethernet/mellanox/mlx5/core/en_main.c: In function 'mlx5e_redirect_rqts_to_drop':
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:2238: error: unknown field 'rqn' specified in initializer
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:2239: warning: missing braces around initializer
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:2239: warning: (near initialization for 'drop_rrp.<anonymous>')

gcc-4.4.4 has issues with anonymous union initializers.  Work around this.

Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sending again, because forgot to include net-dev.

The QoS IP does not accept AVB capabilities to default/queue 0, this way we
guarantee 75% bandwidth for AVB. This patch assures that only queues >= 1
gets CBS confgured. Additional info was also added to stmmac.txt.
Reported-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
net: mpls: Allow users to configure more labels per route

Increase the maximum number of new labels for MPLS routes from 2 to 30.

To keep memory consumption in check, the labels array is moved to the end
of mpls_nh and mpls_iptunnel_encap structs as a 0-sized array. Allocations
use the maximum number of labels across all nexthops in a route for LSR
and the number of labels configured for LWT.

The mpls_route layout is changed to:

   +----------------------+
   | mpls_route           |
   +----------------------+
   | mpls_nh 0            |
   +----------------------+
   | alignment padding    |   4 bytes for odd number of labels; 0 for even
   +----------------------+
   | via[rt_max_alen] 0   |
   +----------------------+
   | alignment padding    |   via's aligned on sizeof(unsigned long)
   +----------------------+
   | ...                  |

Meaning the via follows its mpls_nh providing better locality as the
number of labels increases. UDP_RR tests with namespaces shows no impact
to a modest performance increase with this layout for 1 or 2 labels and
1 or 2 nexthops.

mpls_route allocation size is limited to 4096 bytes allowing on the
order of 30 nexthops with 30 labels (or more nexthops with fewer
labels). LWT encap shares same maximum number of labels as mpls routing.

v3
- initialize n_labels to 0 in case RTA_NEWDST is not defined; detected
  by the kbuild test robot

v2
- updates per Eric's comments
  + added patch to ensure all reads of rt_nhn_alive and nh_flags in
    the packet path use READ_ONCE and all writes via event handlers
    use WRITE_ONCE

  + limit mpls_route size to 4096 (PAGE_SIZE for most arch)

  + mostly killed use of MAX_NEW_LABELS; it exists only for common
    limit between lwt and routing paths
====================
Signed-off-by: David S. Miller <davem@davemloft.net>