The SPDIFRX block is clocked by 2 clocks: peripheral and generic clocks.
Peripheral clock feeds user interface (registers) and generic clock feeds
the receiver.

To enable the receiver the generic clock needs to be enabled and also the
ENABLE bit of MCHP_SPDIFRX_MR register need to be set.

The signal control exported by mchp-spdifrx driver reports wrong status
when the receiver is disabled. This can happen when requesting the signal
and the capture was not previously started. To solve this the receiver
needs to be enabled (by enabling generic clock and setting ENABLE bit of
MR register) before reading the signal status.

As with this fix there are 2 paths now that need to control the generic
clock and ENABLE bit of SPDIFRX_MR register (one path though controls, one
path though configuration) a mutex has been introduced. We can't rely on
subsystem locking as the controls are protected by
struct snd_card::controls_rwsem semaphore and configuration is protected
by a different lock (embedded in snd_pcm_stream_lock_irq()).

The introduction of mutex is also extended to other controls which rely on
SPDIFRX_RSR.ULOCK bit as it has been discovered experimentally that having
both clocks enabled but not the receiver (through ENABLE bit of SPDIFRX.MR)
leads to inconsistent values of SPDIFRX_RSR.ULOCK. Thus on some controls we
rely on software state (dev->trigger_enabled protected by mutex) to
retrieve proper values.

Fixes: ef265c55 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-2-claudiu.beznea@microchip.comSigned-off-by: Mark Brown <broonie@kernel.org>

commit d3268a40 ("ASoC: soc-compress.c: fix NULL dereference")
enables DPCM capture, but it should independent from playback.
This patch fixup it.

Fixes: d3268a40 ("ASoC: soc-compress.c: fix NULL dereference")
Link: https://lore.kernel.org/r/87tu0i6j7j.wl-kuninori.morimoto.gx@renesas.comAcked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/871qnkvo1s.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

Walking the dram->cs array was seen as accesses beyond the first array
item by the compiler. Instead, use the array index directly. This allows
for run-time bounds checking under CONFIG_UBSAN_BOUNDS as well. Seen
with GCC 13 with -fstrict-flex-arrays:

../sound/soc/kirkwood/kirkwood-dma.c: In function
'kirkwood_dma_conf_mbus_windows.constprop':
../sound/soc/kirkwood/kirkwood-dma.c:90:24: warning: array subscript 0 is outside array bounds of 'const struct mbus_dram_window[0]' [-Warray-bounds=]
   90 |                 if ((cs->base & 0xffff0000) < (dma & 0xffff0000)) {
      |                      ~~^~~~~~

Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230127224128.never.410-kees@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

This silences -517 errors and helps figuring out why the device probe
is deferred.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20230119073416.3064918-1-alexander.stein@ew.tq-group.comSigned-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Kiseok Jo <kiseok.jo@irondevice.com>
Link: https://lore.kernel.org/r/20230126020156.3252-4-kiseok.jo@irondevice.comSigned-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: KiseokJo <kiseok.jo@irondevice.com>
Reported-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230126020156.3252-3-kiseok.jo@irondevice.comSigned-off-by: Mark Brown <broonie@kernel.org>

This is never modified and can be made const.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://lore.kernel.org/r/20230126152412.959574-1-luca.ceresoli@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:

The following series will enable multi-stream support for playback and capture
streams.
Currently only a single PCM can be connected to a DAI, with the multi-stream
support it is possible to connect multiple PCMs to a single DAI.

To achieve this we need to make sure that DAIs/AIF are only set up once since
other stream could be connected to it later.

We also need to introduce reference or use counting for widgets to make sure
that they are not going to be destroyed while other streams are still using
them.

With the multi-stream support we also need to extend our current locking scheme
which worked well for simple paths.

Merge series from Astrid Rost <astrid.rost@axis.com>:

Add a generic way to create jack inputs for auxiliary jack detection
drivers (e.g. via i2c, spi), which are not part of any real codec.
The simple-card can be used as combining card driver to add the jacks,
no new one is required.

Create a jack (for input-events) for jack devices in the auxiliary
device list (aux_devs). A device which returns a valid value on
get_jack_type counts as jack device; set_jack is required
to add the jack to the device.

Add set_jack and get_jack_type to allow simple-card-utils to add
a jack for it.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230123135913.2720991-4-astrid.rost@axis.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add a generic way to create jack inputs for auxiliary jack detection
drivers (e.g. via i2c, spi), which are not part of any real codec.
The simple-card can be used as combining card driver to add the jacks,
no new one is required.

Create a jack (for input-events) for jack devices in the auxiliary
device list (aux_devs). A device which returns a valid value on
get_jack_type counts as jack device; set_jack is required
to add the jack to the device.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230123135913.2720991-3-astrid.rost@axis.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add function to return the jack type of snd_jack_types.
This allows a generic card driver to add a jack with the specified
type.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230123135913.2720991-2-astrid.rost@axis.comSigned-off-by: Mark Brown <broonie@kernel.org>

If the pipeline setup fails at the first widget/pipeline then we will have
no spipe stored under the pipeline_list->pipelines, the
pipeline_list->count is 0.

If this is the case we would have a NULL pointer dereference if the
execution is allowed to proceed.

Check for this condition along with the pipeline_list->pipelines check
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-19-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The use_count of the swidget is protect by ALSA core PCM locking with the
exception when an associated kcontrol is changed.

It has been observed that a rightly timed kcontrol access during stream
stop can result of an attempt to send a control update to a widget which
has been freed up between the check of the use_count and the message
sending.

We need to protect the entire sof_widget_setup() and sof_widget_free()
execution to make it safe to rely on the use_count.
Move the code under an _unlocked() function and use a mutex to protect
the execution of the functions for concurrency.
On the control path we need to use the lock only for the kcontrol access,
the widget_kcontrol_setup() op is called with the lock already held.
Reported-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-18-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The sof_widget_free() on the error path will decrement the use count and if
we jump to widget_free: then the use_count will be decremented by two,
which is not correct as we only incremented once with 1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-17-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

When starting/stopping multiple streams in parallel, pipeline triggers
and pipeline frees can get interleaved. So use the same mutex used for
pipeline trigger to protect the pipeline frees as well. Rename the
trigger_mutex to pipeline_state_mutex for more clarity.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-16-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Use the started_count and paused_count to implement reference counting
when making decisions to start/stop/pause pipelines during the FE DAI
trigger. This is necessary to trigger the shared pipelines in the FE DAI
trigger properly.

With IPC4, the FE trigger will issue multiple pipeline state changes,
and the triggers are propagated downstream to connected pipelines by
the SOF driver - not the firmware. This creates a window for race
conditions where an FE trigger preempts another one, which results
in inconsistent pipeline states and refcounts.

This patch introduces a mutex lock for the pcm trigger that guarantees
that IPC4 state and resources are accessed in a serialized manner.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-15-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

For more clarity, rename the struct ipc4_pipeline_set_state_data
variable to trigger_list instead of data. No functionality change.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-14-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Introduce struct snd_sof_pipeline to save the information about
pipelines including the pipeline widget, their status wrt how many PCM's
are using them and whether they are complete or not.

In struct snd_sof_widget, replace pipe_widget with spipe and remove
complete. In struct snd_sof_pcm_stream_pipeline_list, replace
pipe_widgets with pipelines.

Update all users accordingly.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-13-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Use the list of pipelines in the PCM stream's pipeline info to trigger
the pipelines in the right order. Add a helper for triggering pipelines
in batch mode that will be used to trigger multiple pipelines at the
same time.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-12-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Populate the pipeline_info for the PCM stream with the list of pipeline
widgets that need to be handled during the PCM trigger. This will be
used in the IPC-specific PCM trigger op to trigger the pipelines.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-11-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add a new flag, skip_during_fe_trigger, to struct sof_ipc4_pipeline to
skip triggering pipelines in the FE DAI trigger. Set this flag for the
HDA DAI BE pipelines so that their BE pipeline will not be triggered in
the FE DAI trigger. Also, move the trigger handling for all commands
include START/PAUSE_RELEASE for the HDA DAI's to the backend DAI trigger
ops.

For the SSP/DMIC/SDW cases, remove the BE DAI trigger as they involve no
DMA operations and can be triggered in the FE DAI trigger. This is in
preparation to perform batch triggering of all pipelines for the non-HDA
case.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-10-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Define the pcm_setup/pcm_free ops for IPC4. Define a new struct
snd_sof_pcm_stream_trigger_info and add a new field trigger_info of this
type to struct snd_sof_pcm_stream. This will be used to save the list of
pipelines that need to be triggered.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-9-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

These will be used to perform IPC-specific PCM setup/free.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-8-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add a new topology IPC op to set up DAI links and set the link trigger
order to match the expectation based on the IPC type. Note that the
link_setup op implementations for IPC3 and IPC4 are not identical and
have contrasting trigger orders for playback and capture.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-7-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

IPC3 and IPC4 have different requirements for the order in which the FE
CPU and BE CPU DAI trigger callbacks must be invoked. With a regular PCM
start/stop, pipeline widgets are set up during hw_params and freed
during hw_free.

But when the system is suspended when a PCM is running,
pipeline widgets are freed during the SUSPEND trigger callback for the
FE CPU DAI. In order to avoid freeing the pipeline widgets before the BE
CPU DAI trigger is executed, the trigger order was modified in previous
contributions in the PCM dai_link_fixup callback to make sure that the BE
CPU DAI trigger stop/suspend is always invoked before the FE CPU DAI
trigger. But this contradicts the firmware requirement for IPC4 w.r.t.
ordering of pipeline triggers.

So, remove the freeing of pipeline widgets during FE CPU DAI suspend
trigger and handle it during system suspend when the
tear_down_all_pipelines() IPC op is invoked. This will be followed up
with a patch to fix the trigger order for IPC4.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-6-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

When walking the list of the widgets from the source to the sink, we
accidentally also end up preparing/setting up the widgets that are not
in the list of connected DAPM widgets associated with the PCM. Avoid
this by checking if a widget is part of the connected DAPM widget list
during widget prepare, unprepare, setup or free.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-5-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Calling the sof_widget_setup/free() for the DAI/AIF widgets inside the
snd_soc_dapm_widget_for_each_sink_path() loop will end up setting up or
freeing the widget multiple times if there are multiple paths leaving
the widget. Fix this by moving the widget setup/free for the starting
widget in each path outside the loop.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-4-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Export the widget_in_list() function to be used by other modules.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-3-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The FW currently ignores unbinding routes if the source and sink widgets
belong to the same pipeline. So no need to send the IPC at all in the
first place.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-2-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

If panic_on_warn is set and compress stream(DPCM) is started,
then kernel panic occurred because card->pcm_mutex isn't held appropriately.
In the following functions, warning were issued at this line
"snd_soc_dpcm_mutex_assert_held".

static int dpcm_be_connect(struct snd_soc_pcm_runtime *fe,
		struct snd_soc_pcm_runtime *be, int stream)
{
	...
	snd_soc_dpcm_mutex_assert_held(fe);
	...
}

void dpcm_be_disconnect(struct snd_soc_pcm_runtime *fe, int stream)
{
	...
	snd_soc_dpcm_mutex_assert_held(fe);
	...
}

void snd_soc_runtime_action(struct snd_soc_pcm_runtime *rtd,
			    int stream, int action)
{
	...
	snd_soc_dpcm_mutex_assert_held(rtd);
	...
}

int dpcm_dapm_stream_event(struct snd_soc_pcm_runtime *fe, int dir,
	int event)
{
	...
	snd_soc_dpcm_mutex_assert_held(fe);
	...
}

These functions are called by soc_compr_set_params_fe, soc_compr_open_fe
and soc_compr_free_fe
without pcm_mutex locking. And this is call stack.

[  414.527841][ T2179] pc : dpcm_process_paths+0x5a4/0x750
[  414.527848][ T2179] lr : dpcm_process_paths+0x37c/0x750
[  414.527945][ T2179] Call trace:
[  414.527949][ T2179]  dpcm_process_paths+0x5a4/0x750
[  414.527955][ T2179]  soc_compr_open_fe+0xb0/0x2cc
[  414.527972][ T2179]  snd_compr_open+0x180/0x248
[  414.527981][ T2179]  snd_open+0x15c/0x194
[  414.528003][ T2179]  chrdev_open+0x1b0/0x220
[  414.528023][ T2179]  do_dentry_open+0x30c/0x594
[  414.528045][ T2179]  vfs_open+0x34/0x44
[  414.528053][ T2179]  path_openat+0x914/0xb08
[  414.528062][ T2179]  do_filp_open+0xc0/0x170
[  414.528068][ T2179]  do_sys_openat2+0x94/0x18c
[  414.528076][ T2179]  __arm64_sys_openat+0x78/0xa4
[  414.528084][ T2179]  invoke_syscall+0x48/0x10c
[  414.528094][ T2179]  el0_svc_common+0xbc/0x104
[  414.528099][ T2179]  do_el0_svc+0x34/0xd8
[  414.528103][ T2179]  el0_svc+0x34/0xc4
[  414.528125][ T2179]  el0t_64_sync_handler+0x8c/0xfc
[  414.528133][ T2179]  el0t_64_sync+0x1a0/0x1a4
[  414.528142][ T2179] Kernel panic - not syncing: panic_on_warn set ...

So, I reposition and add pcm_mutex to resolve lockdep error.
Signed-off-by: Shinhyung Kang <s47.kang@samsung.com>
Link: https://lore.kernel.org/r/016401d90ac4$7b6848c0$7238da40$@samsung.comSigned-off-by: Mark Brown <broonie@kernel.org>

We know that "irq < 0", so delete the unnecessary check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/Y9JHSwcfdNcfMjjt@kiliSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>:

Update va-macro driver dt-bindings and add missing properties in sc7280
machine driver dt-bindings.

Changes since v2:
    -- Update commit message and example in "Add platform property" patch.
    -- Update commit message in "Update clock name" patch.
Changes since v1:
    -- Remove sound-dai cells property patch.
    -- Update example in clock name change patch.
    -- Update commit message and add maxItems in platform proerty patch.

Srinivasa Rao Mandadapu (2):
  ASoC: qcom: dt-bindings: lpass-va-macro: Update clock name
  ASoC: dt-bindings: google,sc7280-herobrine: Add platform property

 .../devicetree/bindings/sound/google,sc7280-herobrine.yaml   | 12 ++++++++++++
 .../devicetree/bindings/sound/qcom,lpass-va-macro.yaml       |  4 ++--
 2 files changed, 14 insertions(+), 2 deletions(-)

--
2.7.4

Currently, we use the same channel mask for aggregated speakers.
It works fine for playback because we duplicate the audio data for all
aggregated speakers. But we need to get audio data from each aggregated
speaker and combine them to the captured audio. So we need to set
non-overlapping channel mask for aggregated ALH DAIs.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230125141317.30302-1-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The fallback compatible in a list (the last one) cannot be enum, because
it is always fixed.  Also if such fallback is used alone ("Generic"
case), it's not a list anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230126100722.9473-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The corresponding IPC4 module of snd_soc_dapm_buffer widget is module
-to-module copier.
The module-to-module copier is a buffer-like component with demuxing
capabilities.
Rename the host_token_list to common_copier_token_list since it will
be used by host copier and module-to-module copier.
The setup callback is almost the same as sof_ipc4_widget_setup_pcm except
the gtw_cfg data, and the free callback is exactly the same as
sof_ipc4_widget_free_comp_pcm. To reduce the duplication, the commit
reuses the setup and free callbacks.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230126110637.25542-1-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add platform property in sc7280 machine driver bindings for including
platform subnode in dai-links.
This is required for binding the frontend dai driver to do dynamic pcm
routing in ADSP based platforms.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1674468802-14834-3-git-send-email-quic_srivasam@quicinc.comSigned-off-by: Mark Brown <broonie@kernel.org>

Update clock name from core to macro in lpass-va-macro node
to make it compatible with existing driver and existing DTS files.

Fixes: 67d99b23 ("ASoC: qcom: dt-bindings: add bindings for lpass va macro codec")
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Reported-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/1674468802-14834-2-git-send-email-quic_srivasam@quicinc.comSigned-off-by: Mark Brown <broonie@kernel.org>

Fix spelling in sound/soc/ Kconfig files:
s/upto/up to/
(reported by codespell)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de> #rockchip
Link: https://lore.kernel.org/r/20230124181746.19028-1-rdunlap@infradead.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Replace SNDRV_DMA_TYPE_DEV by SNDRV_DMA_TYPE_NONCOHERENT for pcm
buffer allocation. We measured about 18x performance improvement
when accessing the snd_pcm_mmap() buffer from userspace.

Eg: aarch64 with internal speaker
==
SNDRV_DMA_TYPE_DEV
    frames_per_second=66.4557M/s
    max_time_per_4096_frames=106.094u
    time_per_4096_frames=61.6351us

SNDRV_DMA_TYPE_NONCOHERENT
    frames_per_second=1028.58M/s
    max_time_per_4096_frames=20.312u
    time_per_4096_frames=3.98221us
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Link: https://lore.kernel.org/r/20221208084200.2136311-1-judyhsiao@chromium.orgSigned-off-by: Mark Brown <broonie@kernel.org>