- 22 May, 2021 7 commits
-
-
James Smart authored
When processing an NVMe ERSP IU which didn't match the optimized CQE-only path, the status was being left to the WQE status. WQE status is non-zero as it is indicating a non-optimized completion that needs to be handled by the driver. Fix by clearing the status field when falling into the non-optimized case. Log message added to track optimized vs non-optimized debug. Link: https://lore.kernel.org/r/20210514195559.119853-3-jsmart2021@gmail.comCo-developed-by:
Justin Tee <justin.tee@broadcom.com> Signed-off-by:
James Smart <jsmart2021@gmail.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
James Smart authored
While testing NPIV and watching logins and used RPI levels, it was seen the used RPI count was much higher than the number of remote ports discovered. Code inspection showed that remote port removals on any NPIV instance are releasing the RPI, but not performing an UNREG_RPI with the adapter thus the reference counting never fully drops and the RPI is never fully released. This was happening on NPIV nodes due to a log of fabric ELS's to fabric addresses. This lack of UNREG_RPI was introduced by a prior node rework patch that performed the UNREG_RPI as part of node cleanup. To resolve the issue, do the following: - Restore the RPI release code, but move the location to so that it is in line with the new node cleanup design. - NPIV ports now release the RPI and drop the node when the caller sets the NLP_RELEASE_RPI flag. - Set the NLP_RELEASE_RPI flag in node cleanup which will trigger a release of RPI to free pool. - Ensure there's an UNREG_RPI at LOGO completion so that RPI release is completed. - Stop offline_prep from skipping nodes that are UNUSED. The RPI may not have been released. - Stop the default RPI handling in lpfc_cmpl_els_rsp() for SLI4. - Fixed up debugfs RPI displays for better debugging. Fixes: a70e63ee ("scsi: lpfc: Fix NPIV Fabric Node reference counting") Link: https://lore.kernel.org/r/20210514195559.119853-2-jsmart2021@gmail.com Cc: <stable@vger.kernel.org> # v5.11+ Co-developed-by:
-
Martin Wilck authored
If an RTPG fails, we can't infer anything wrt. the state of the ports in the port group except that we were unable to reach the one port on which the RTPG had failed. "offline" is just a secondary port state, which means that we can't infer the state of any port in the PG from the failure (in fact, even the failed port might still be in "active/optimized" primary port access state). Therefore, when we encounter an RTPG failure, we should retry the RTPG on a different port. This avoids falsely setting port states to offline for unreachable ports. To do this, ports on which an RTPG has failed are temporarily set to "disabled" to avoid repeating the failed I/O on the same target port. Once the RTPG has either succeeded on one port or failed on all ports of the PG, the ports are enabled again. Link: https://lore.kernel.org/r/20210514153214.5626-1-mwilck@suse.comSigned-off-by:
Martin Wilck <mwilck@suse.com> Signed-off-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
-
Jiapeng Chong authored
Variable rval is set to QLA_SUCCESS but this value is never read as it is overwritten later on. Hence it is a redundant assignment and can be removed. Clean up the following clang-analyzer warning: drivers/scsi/qla2xxx/qla_init.c:4359:2: warning: Value stored to 'rval' is never read [clang-analyzer-deadcode.DeadStores]. Link: https://lore.kernel.org/r/1620643206-127930-1-git-send-email-jiapeng.chong@linux.alibaba.comReported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Signed-off-by:
-
Colin Ian King authored
Don't populate the const array granularity_tbl on the stack but instead make it static. Makes the object code smaller by 190 bytes: Before: text data bss dec hex filename 25563 6908 0 32471 7ed7 ./drivers/scsi/ufs/ufs-exynos.o After: text data bss dec hex filename 25213 7068 0 32281 7e19 ./drivers/scsi/ufs/ufs-exynos.o (gcc version 10.3.0) Link: https://lore.kernel.org/r/20210505190104.70112-1-colin.king@canonical.comSigned-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Wei Ming Chen authored
Replace /*FALLTHROUGH*/ comment with pseudo-keyword macro 'fallthrough'. Link: https://lore.kernel.org/r/20210518131823.2586-1-jj251510319013@gmail.comSigned-off-by:
Wei Ming Chen <jj251510319013@gmail.com> Signed-off-by:
-
Keoseong Park authored
checkpatch reports the following errors: ERROR: space prohibited before that ',' (ctx:WxW) #945: FILE: drivers/scsi/ufs/ufshcd.h:945: +int ufshcd_init(struct ufs_hba * , void __iomem * , unsigned int); ^ ERROR: space prohibited before that ',' (ctx:WxW) #945: FILE: drivers/scsi/ufs/ufshcd.h:945: +int ufshcd_init(struct ufs_hba * , void __iomem * , unsigned int); ^ Remove unnecessary whitespace in ufshcd.h. Link: https://lore.kernel.org/r/2038148563.21621340102306.JavaMail.epsvc@epcpadp3Signed-off-by:
Keoseong Park <keosung.park@samsung.com> Signed-off-by:
-
- 21 May, 2021 13 commits
-
-
Zhen Lei authored
Fix some spelling mistakes in comments: pathes ==> paths Resouce ==> Resource retreived ==> retrieved recevied ==> received interruped ==> interrupted [mkp: kept 'keep-alives' and 'busses'] Link: https://lore.kernel.org/r/20210517095945.7363-1-thunder.leizhen@huawei.comSigned-off-by:
Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by:
-
Juerg Haefliger authored
Remove leading spaces before tabs in Kconfig file(s) by running the following command: $ find drivers/scsi -name 'Kconfig*' | xargs sed -r -i 's/^[ ]+\t/\t/' Link: https://lore.kernel.org/r/20210517095835.81733-1-juergh@canonical.comSigned-off-by:
Juerg Haefliger <juerg.haefliger@canonical.com> Signed-off-by:
-
kernel test robot authored
drivers/target/target_core_user.c:1424:9-10: WARNING: return of 0/1 in function 'tcmu_handle_completions' with return type bool Return statements in functions returning bool should use true/false instead of 1/0. Generated by: scripts/coccinelle/misc/boolreturn.cocci Link: https://lore.kernel.org/r/20210515230358.GA97544@60d1edce16e0 Fixes: 9814b55c ("scsi: target: tcmu: Return from tcmu_handle_completions() if cmd_id not found") CC: Bodo Stroesser <bostroesser@gmail.com> Reported-by:
kernel test robot <lkp@intel.com> Acked-by:
Bodo Stroesser <bostroesser@gmail.com> Signed-off-by:
-
Bart Van Assche authored
The comments in the enum ufs_pm_level definition are redundant. Remove the comments from the ufs_pm_level enum and use designated initializers in the ufs_pm_lvl_states[] definition instead. Link: https://lore.kernel.org/r/20210519202058.12634-3-bvanassche@acm.org Cc: Stanley Chu <stanley.chu@mediatek.com> Cc: Can Guo <cang@codeaurora.org> Cc: Bean Huo <beanhuo@micron.com> Cc: Jaegeuk Kim <jaegeuk@kernel.org> Cc: Asutosh Das <asutoshd@codeaurora.org> Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Signed-off-by:
-
Sergey Shtylyov authored
After commit 6c11dc06 ("scsi: hisi_sas: Fix IRQ checks") we have the error codes returned by platform_get_irq() ready for the propagation upsream in interrupt_init_v1_hw() -- that will fix still broken deferred probing. Let's propagate the error codes from devm_request_irq() as well since I don't see the reason to override them with -ENOENT... Link: https://lore.kernel.org/r/49ba93a3-d427-7542-d85a-b74fe1a33a73@omp.ruAcked-by:
John Garry <john.garry@huawei.com> Signed-off-by:
Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by:
-
Jiapeng Chong authored
Eliminate the follow smatch warning: drivers/scsi/bfa/bfa_svc.c:3176 bfa_fcport_send_enable() warn: inconsistent indenting. Link: https://lore.kernel.org/r/1621590368-72041-1-git-send-email-jiapeng.chong@linux.alibaba.comReported-by:
-
zuoqilin authored
Change 'chnage' to 'change'. Link: https://lore.kernel.org/r/20210521092153.379-1-zuoqilin1@163.comSigned-off-by:
zuoqilin <zuoqilin@yulong.com> Signed-off-by:
-
zuoqilin authored
Change "avaibale" and "avaible" to "available". Link: https://lore.kernel.org/r/20210521082808.1925-1-zuoqilin1@163.comSigned-off-by:
-
Daniel Wagner authored
Remove the double listed FC_FPORT_DELETING from the mask creation. Commit 260f4aed ("scsi: scsi_transport_fc: return -EBUSY for deleted vport") added VC_VPORT_DELETING to the flag masks. This is not necessary as FC_FPORT_DEL is defined as VC_FPORT_DELETED | FC_FPORT_DELETING. Link: https://lore.kernel.org/r/20210520073127.132456-1-dwagner@suse.de Cc: Hannes Reinecke <hare@suse.de> Signed-off-by:
Daniel Wagner <dwagner@suse.de> Signed-off-by:
-
ching Huang authored
Update driver version to v1.50.00.05-20210429. Link: https://lore.kernel.org/r/d0c6dc6431f0e46db6583dc0d04d7983b420d4da.camel@areca.com.twSigned-off-by:
ching Huang <ching2048@areca.com.tw> Signed-off-by:
-
ching Huang authored
It is possible for the IOP to be delayed in updating the doorbell status. The doorbell status should not be 0 so loop until the value changes. Link: https://lore.kernel.org/r/afdfdf7eabecf14632492c4987a6b9ac6312a7ad.camel@areca.com.twSigned-off-by:
-
Yang Yingliang authored
Use vzalloc() instead of vmalloc() and memset(0) to simpify the code. Link: https://lore.kernel.org/r/20210518132018.1312995-1-yangyingliang@huawei.comReviewed-by:
Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Signed-off-by:
-
Bart Van Assche authored
In the Linux kernel definitions of data structures should occur in .c files. Hence move the exynos7_uic_attr definition from a .h into a .c file. Additionally, declare exynos_ufs_drvs static. This patch fixes the following two sparse warnings: drivers/scsi/ufs/ufs-exynos.h:248:28: warning: symbol 'exynos_ufs_drvs' was not declared. Should it be static? drivers/scsi/ufs/ufs-exynos.h:250:28: warning: symbol 'exynos7_uic_attr' was not declared. Should it be static? Link: https://lore.kernel.org/r/20210509213817.4348-1-bvanassche@acm.org Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Kiwoong Kim <kwmad.kim@samsung.com> Reviewed-by:
Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by:
-
- 15 May, 2021 20 commits
-
-
Samuel Holland authored
The controller expects all data it sends/receives to be little-endian. Therefore, the packet struct definitions should use the __le16/32/64 types. Once those are correct, sparse reports several issues with the driver code, which are fixed here as well. The main issue observed was at the call to scsi_set_resid(), where the byteswapped parameter would eventually trigger the alignment check at drivers/scsi/sd.c:2009. At that point, the kernel would continuously complain about an "Unaligned partial completion", and no further I/O could occur. This gets the controller working on big endian powerpc64. Link: https://lore.kernel.org/r/20210427235915.39211-4-samuel@sholland.orgSigned-off-by:
Samuel Holland <samuel@sholland.org> Signed-off-by:
-
Samuel Holland authored
Currently, all command packet structs used by this driver are packed. However, only one (TW_SG_Entry) actually needs to be packed, because it uses 64-bit addresses at 32-bit alignment. To improve the quality of generated code, stop packing all of the other command packet structs. This requires adjusting the type of one misaligned "reserved" member. After this change, pahole reports that only one type had its layout change: the tw_compat_info member of TW_Device_Extension is now naturally aligned. Link: https://lore.kernel.org/r/20210427235915.39211-3-samuel@sholland.orgSigned-off-by:
-
Samuel Holland authored
In preparation for removing the "#pragma pack(1)" from the driver, fix all instances where a trailing array member could be replaced by a flexible array member. Since a flexible array member has zero size, it introduces no padding, whether or not the struct is packed. Link: https://lore.kernel.org/r/20210427235915.39211-2-samuel@sholland.orgSigned-off-by:
-
Nigel Christian authored
The nested for loop variables i and j in beiscsi_free_mem() are initialized twice. The values outside of the loops are redundant and can be removed. Addresses-Coverity: ("Unused value") Link: https://lore.kernel.org/r/YJ2mMHNqAgTNVVj+@fedoraSigned-off-by:Nigel Christian <nigel.l.christian@gmail.com> Signed-off-by:
-
Keoseong Park authored
Remove unnecessary parenthesis in ufshcd_is_wb_flags() and ufshcd_is_wbattrs(). Link: https://lore.kernel.org/r/1891546521.01620896402035.JavaMail.epsvc@epcpadp3Signed-off-by:
-
Bart Van Assche authored
Remove these macros to make the UFS driver source code easier to read. These macros were introduced by commit 57d104c1 ("ufs: add UFS power management support"). Link: https://lore.kernel.org/r/20210513171229.7439-1-bvanassche@acm.org Cc: Can Guo <cang@codeaurora.org> Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Avri Altman <avri.altman@wdc.com> Cc: Stanley Chu <stanley.chu@mediatek.com> Cc: Bean Huo <beanhuo@micron.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Acked-by:
Avri Altman <avri.altman@wdc.com> Signed-off-by:
-
Christophe JAILLET authored
'lp' is unused, it is just declared and zeroed Remove it. Link: https://lore.kernel.org/r/d10ccee35e35bf33d651f2e0163034d7c451520b.1618944442.git.christophe.jaillet@wanadoo.frSigned-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Konstantin Shelekhin authored
Extend the standard INQUIRY data to 96 bytes and fill in the VERSION DESCRIPTOR fields. The layout follows SPC-4: - SCSI architecture standard - SCSI transport protocol standard - SCSI primary command set standard - SCSI device type command set standard All version descriptor values are defined as "no version claimed" because some initiators fail to recognize anything else. [mkp: whitespace] Link: https://lore.kernel.org/r/20210513192804.1252142-3-k.shelekhin@yadro.comReviewed-by:
Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by:
Konstantin Shelekhin <k.shelekhin@yadro.com> Signed-off-by:
-
Konstantin Shelekhin authored
Bump the SCSI primary command set standard to SPC-4. The upcoming version descriptors will report newer SCSI standards (like SBC-3) that are not defined in SPC-3. Link: https://lore.kernel.org/r/20210513192804.1252142-2-k.shelekhin@yadro.comReviewed-by:
-
Sergey Samoylenko authored
Implement an attribute which provides a way to set a company specific WWN in configfs via: target/core/$backstore/$name/wwn/company_id The Open Fabrics Alliance ID 001405h remains the default. Link: https://lore.kernel.org/r/20210420185920.42431-3-s.samoylenko@yadro.comSigned-off-by:
Sergey Samoylenko <s.samoylenko@yadro.com> Signed-off-by:
-
Sergey Samoylenko authored
Both the INQUIRY handling and the XCOPY implementation provide functions to generate an NAA designator. In addition, these functions are poorly named: - spc_parse_naa_6h_vendor_specific() - target_xcopy_gen_naa_ieee() Introduce a common NAA 6 designator generation function, spc_gen_naa_6h_vendor_specific(). Link: https://lore.kernel.org/r/20210420185920.42431-2-s.samoylenko@yadro.comSigned-off-by:
-
Jiapeng Chong authored
Variable pg_size is set to '0x100 << pg_size', but this value is never read and it is not used later on. Hence it is a redundant assignment and can be removed. Clean up the following clang-analyzer warning: drivers/target/sbp/sbp_target.c:1264:3: warning: Value stored to 'pg_size' is never read [clang-analyzer-deadcode.DeadStores]. Link: https://lore.kernel.org/r/1620902977-57076-1-git-send-email-jiapeng.chong@linux.alibaba.comReported-by:
-
Jiapeng Chong authored
Variable rc is set to '-1', but this value is never read as it is overwritten later. Hence it is a redundant assignment and can be removed. Clean up the following clang-analyzer warning: drivers/message/fusion/mptbase.c:6996:2: warning: Value stored to 'rc' is never read [clang-analyzer-deadcode.DeadStores]. Link: https://lore.kernel.org/r/1620814327-25427-1-git-send-email-jiapeng.chong@linux.alibaba.comReported-by:
-
Brian King authored
If rport target discovery commands fail for some reason, they get retried up to a set number of retries. Once the retry limit is exceeded, the target is deleted. In order to delete the target, we either need to do an implicit logout or a move login. In the move login case, if the move login fails, we want to retry it. This ensures the retry counter gets reinitialized so the move login will get retried. Link: https://lore.kernel.org/r/1620756740-7045-4-git-send-email-brking@linux.vnet.ibm.comSigned-off-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Brian King authored
If fast fail is enabled and we encounter a WWPN moving from one port id to another port id with I/O outstanding, if we use the move login MAD, although it will work, it will leave any outstanding I/O still outstanding to the old port id. Eventually, the SCSI command timers will fire and we will abort these commands, however, this is generally much longer than the fast fail timeout, which can lead to I/O operations being outstanding for a long time. This patch changes the behavior to avoid the move login if fast fail is enabled. Once terminate_rport_io cleans up the rport, then we force the target back through the delete process, which re-drives the implicit logout, then kicks us back into discovery where we will discover the WWPN at the new location and do a PLOGI to it. Link: https://lore.kernel.org/r/1620756740-7045-3-git-send-email-brking@linux.vnet.ibm.comSigned-off-by:
-
Brian King authored
When service is being performed on an SVC with NPIV enabled, the WWPN of the canister / node being serviced fails over to the another canister / node. This looks to the ibmvfc driver as a WWPN moving from one SCSI ID to another. The driver will first attempt to do an implicit logout of the old SCSI ID. If this works, we simply delete the rport at the old location and add an rport at the new location and the FC transport class handles everything. However, if there is I/O outstanding, this implicit logout will fail, in which case we will send a "move login" request to the VIOS. This will cancel any outstanding I/O to that port, logout the port, and PLOGI the new port. Recently we've encountered a scenario where the move login fails. This was resulting in an attempted plogi to the new scsi id, without the old scsi id getting logged out, which is a VIOS protocol violation. To solve this, we want to keep tracking the old scsi id as the current scsi id. That way, once terminate_rport_io cancels the outstanding i/o, it will send us back through to do an implicit logout of the old scsi id, rather than the new scsi id, and then we can plogi the new scsi id. Link: https://lore.kernel.org/r/1620756740-7045-2-git-send-email-brking@linux.vnet.ibm.comSigned-off-by:
-
Bodo Stroesser authored
The bit definition TCM_DEV_BIT_PLUGGED should correctly be named TCMU_DEV_BIT_PLUGGED, since all other bits in the same bitfield have prefix TCMU_. Link: https://lore.kernel.org/r/20210512140654.31249-1-bostroesser@gmail.comSigned-off-by:
-
Xiang Chen authored
Commit 3be8828f ("scsi: core: Avoid that ATA error handling can trigger a kernel hang or oops") moved rcu to scsi_cmnd instead of shost. Modify "shost->rcu" to "scmd->rcu" in a comment. Link: https://lore.kernel.org/r/1620646526-193154-1-git-send-email-chenxiang66@hisilicon.comSigned-off-by:
Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by:
-
Guenter Roeck authored
The result of container_of() operations is never NULL unless the embedded element is the first element of the structure, which is not the case here. The NULL checks are therefore unnecessary and misleading. Remove them. The changes in this patch were made automatically using the following Coccinelle script. @@ type t; identifier v; statement s; @@ <+... ( t v = container_of(...); | v = container_of(...); ) ... when != v - if (\( !v \| v == NULL \) ) s ...+> Link: https://lore.kernel.org/r/20210510041211.2051325-1-linux@roeck-us.netSigned-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Guenter Roeck authored
The structure pointer passed to container_of() is never NULL; that was already checked. That means that the result of container_of() operations on it is also never NULL, even though se_node_acl is the first element of the structure embedding it. On top of that, it is misleading to perform a NULL check on the result of container_of() because the position of the contained element could change, which would make the test invalid. Remove the unnecessary NULL check. As it turns out, the container_of operation was only made for the purpose of the NULL check. If the container_of is actually needed, it is repeated later. Remove the container_of operation as well. The NULL check was identified and removed with the following Coccinelle script. @@ type t; identifier v; statement s; @@ <+... ( t v = container_of(...); | v = container_of(...); ) ... when != v - if (\( !v \| v == NULL \) ) s ...+> Link: https://lore.kernel.org/r/20210510040817.2050266-1-linux@roeck-us.net Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Hou Pu <houpu@bytedance.com> Cc: Mike Christie <michael.christie@oracle.com> Signed-off-by:
-
