- 08 Jul, 2014 13 commits
-
-
Anantha Krishnan authored
Add support for the QCA6174 chip. T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 30 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3432 Rev=00.02 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: Anantha Krishnan <ananthk@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
All LE controllers always implicitly stop advertising when establishing connections. Therefore, be sure to clear the flag in the event handler for new LE connections. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
If the connectable state change doesn't require any special HCI commands the set_connectable_update_settings() function is used instead of the set_connectable_complete() function. We must therefore make sure to call hci_update_background_scan() there as well. This code path is used also when we're powered off, but that's fine since hci_update_background_scan() has the necessary checks for it. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
The connectable and discoverable mgmt settings are supported both for LE and BR/EDR controllers so they do not belong behind a lmp_bredr_capable() condition. This patch fixes the issue in get_supported_settings(). Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
If any of the HCI commands from the hci_stop_discovery function were successfully sent we need to set the discovery state to STOPPING. The Stop Discovery code was already handling this, but the code in clean_up_hci_state was not. This patch updates the hci_stop_discovery to return a bool to indicate whether it queued any commands and the clean_up_hci_state() function respectively to look at the return value and call hci_discovery_set_state() if necessary. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
There are many different places that can disable LE scanning but we only want to re-enable advertising in hci_cc_le_set_scan_enable() for a very specific use case, which is when the active scanning part of Start Discovery is complete. Because of this, fix the discovery state check to test for the exact state. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
Many controllers allow simultaneous active scanning and advertising (e.g. Intel and Broadcom) but some do not (e.g. CSR). It's therefore safest to implement mutual exclusion of these states in the kernel. This patch ensures that the two states are never entered simultaneously. Extra precaution needs to be taken for outgoing connection attempts in slave role (i.e. through directed advertising) in which case the operation that came first has precedence and the one that comes after gets a rejection. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
Most controllers do not support advertising while initiating an LE connection. We also have to first disable current advertising if the initiation is going to happen through direct advertising. Therefore, simply stop advertising as the first thing when starting to issue commands to establish an LE connection. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
When deciding to call disable_advertising() we're interested in the real state instead of the mgmt setting. Use therefore HCI_LE_ADV instead of the HCI_ADVERTISING flag. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
By adding support for disabling advertising when necessary and doing the checks for existing LE connections inside the enable_advertising function we can simplify the calling code quite a lot. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
Now that we have a flag for tracking the real advertising state we should use that to determine whether it's safe to update the random address or not. The couple of places that were clearing the flag due to a pending request need to be updated too. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
Since the real advertising state is now tracked with its own flag we can simply set/unset the HCI_ADVERTISING flag in the set_advertising_complete function. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
Having a single HCI_ADVERTISING flag is problematic since it tries to track both the real advertising state and the corresponding mgmt setting. To make the logic simpler and more reliable add a new flag that only tracks the actual advertising state that has been written to the controller. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
- 07 Jul, 2014 10 commits
-
-
Johan Hedberg authored
For adapters that do not support LE and ones where LE hasn't been enabled we shouldn't be trying to initiate background scanning. This patch adds an extra check to the hci_update_background_scan() to ensure that we bail out if HCI_LE_ENABLED is not set. Since we do allow user space to feed the kernel with LE connection parameters even when LE is not enabled we now need to also call hci_update_background_scan() as soon as LE gets enabled so that scanning gets started if necessary. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
If we have both LE scanning and advertising simultaneously enabled we need a way to tell hci_connect_le() in which role to initiate a connection. This patch adds a new parameter to the function to give it the necessary information. For auto-connect and mgmt_pair_device we always use master role, whereas for L2CAP users (in practice sockets) we use slave role whenever HCI_ADVERTISING is set and master role otherwise. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
The auth_type value which gets assigned to hci_conn->auth_type is something that's only used for BR/EDR connections and is of no value for LE connections. It makes therefore little sense to pass it to the hci_connect_le() function. This patch removes the parameter from the function. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
Enabling passive scanning always when we're connectable aligns us with the BR/EDR page scanning. This is also consistent with the fact that the code dealing with passive scanning results will actively try to connect any direct advertising event when we're connectable. This patch implements the feature by adding the connectable condition to hci_update_background_scan() checks for starting scanning and by calling hci_update_background_scan() whenever the connectable state changes. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
If we have an active discovery going on we shouldn't do any changes to LE scanning when hci_update_background_scan() is called (a call which can happen for many different reasons). This patch fixes the issue by returning from the function if the discovery state is anything else except DISCOVERY_STOPPED. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
In a subsequent patch the hci_update_background_scan() function will depend on being able to know the current discovery state. For this to be possible we need to set the new state early in the function. Since we also need to check what the old state was this patch introduces an extra variable for tracking it. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
Since the only caller of this function doesn't care about the return value anymore let's just remove it. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
Now that we have the process_adv_report() function doing the IRK lookup and updating the bdaddr we don't need to do this anymore in mgmt.c in the mgmt_device_found() function. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
If we have devices set as to be connected we should connect to them even during normal discovery if we get a connectable advertising event. If we also have HCI_CONNECTABLE set we should connect ADV_DIRECT_IND events even to devices that we don't have in our pend_le_conns list. This patch implements such behavior by passing the advertising report type to check_pending_le_conn() and calls that function regardless of what type of scanning we are doing. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Marcel Holtmann authored
Instead of setting data->isoc manually, use BTUSB_BROKEN_ISOC to indicate that isochronous endpoints are not needed for CSR USB sniffer devices. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
- 06 Jul, 2014 14 commits
-
-
Marcel Holtmann authored
The hdev->send driver callback is mandatory to be provided by a driver before calling hci_register_dev. So enforce it and return EINVAL in case it is not available. All existing drivers are providing this callback anyway, so this is just an extra sanity check. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
The drivers are allowed to just return an error from hdev->send callback and in that case the driver does not own the SKB. Which means that the caller has to free the SKB. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
The isochronous endpoints are not valid when the Intel Bluetooth controller boots up in bootloader mode. So just mark these endpoints as broken and then they will not be configured. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
The interrupt interface for the Intel USB bootloader devices is only enabled after receiving SetInterface(0, AltSetting=0). When this USB command is not send, then no HCI events will be received. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Johan Hedberg authored
When we get an LE connection complete event we should restart background scanning if there are any devices needing it. So far the code was only making the decision based on whether the completed connection had any stored parameters or not. This patch ensures that we trigger background scanning always when necessary. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Marcel Holtmann authored
The module parameters to ignore devices based on USB VID/PID are not needed at all. So just remove them. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
When the driver sets HCI_QUIRK_RAW_DEVICE, the controller will be set as unconfigured. However running the unconfigured init procecure is not useful since raw-only devices are not allowed to change its configuration. This change skips the init procedure and just allows user channel operation for this device. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
Intel Bluetooth devices that boot up in bootloader mode can not be used as generic HCI devices, but their HCI transport is still valuable and so bring that up as raw-only devices. T: Bus=02 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 14 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=ff(vend.) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=8087 ProdID=0a5a Rev= 0.00 S: Manufacturer=Intel(R) Corporation S: Product=Intel(R) Wilkins Peak 2x2 S: SerialNumber=001122334455 WP_A0 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Johan Hedberg authored
When we establish connections as a consequence of receiving an advertising report it makes no sense to wait the normal 20 second LE connection timeout. This patch modifies the hci_connect_le function to take an extra timeout value and uses a lower 2 second timeout for the auto-connection case. This timeout is intentionally chosen to be just a bit higher than the 1.28 second timeout that High Duty Cycle Advertising uses. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Marcel Holtmann authored
When an unconfigured controllers reaches the configured state, it is important to change the HCI_RAW flag. It indicates to userspace that the controller is fully operational. External configuration allows to bring the controller back into an unconfigured state. In that case make sure HCI_RAW flag is set again. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
This adds support for changing the public device address. This feature is required by controllers that do not provide a public address and have HCI_QUIRK_INVALID_BDADDR set. Even if a controller has a public device address, this is useful when an embedded system wants to use its own value. As long as the driver provides the set_bdaddr callback, this allows changing the device address before powering on the controller. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
When the external configuration triggers the switch to a configured controller, it means the setup needs to be run. Controllers that start out unconfigured have only run limited set of HCI commands. This is not enough for complete operation and thus run the setup procedure before announcing the new controller index. This introduces HCI_CONFIG flag as companion to HCI_SETUP flag. The HCI_SETUP flag is only used once for the initial setup procedure. And during that procedure hdev->setup driver callback is called. With the new HCI_CONFIG the switch from unconfigured to configured state is triggering the same setup procedure just without hdev->setup. This is required since bringing a controller back to unconfigured state from configured state is possible. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Johan Hedberg authored
When calling Device Remove with BDADDR_ANY we should in a similar way emit Device Removed events as we do when removing a single device. Since we have to iterate the list and call device_removed() the dedicated hci_conn_params_clear_enabled() is not really useful anymore. This patch removes the helper function and does the event emission and list item removal in a single loop. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hedberg authored
BR/EDR has the connection request and connection request rejection, but LE doesn't have anything similar. We still request LE connections to blocked devices to be disconnected but it's possible that ACL data slips through before that. The check in l2cap_recv_frame really only needs to be for LE and not BR/EDR because of this. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
- 05 Jul, 2014 3 commits
-
-
Marcel Holtmann authored
During the setup phase of a controller, the Bluetooth address will be read and to have that original address available for later use, store it as setup address. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
For an unconfigured controller it is required to read at least the local version information. If the set_bdaddr driver callback is provideded, then also the local Bluetooth address will be read. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Marcel Holtmann authored
The HCI event callbacks have grown over the last years and some functions handle status checking different than others. For the simple ones, check the status at the beginning and exit if an error with the HCI command occured. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-