Some motherboards are broken and have no address set. Failing at probe time
prevents the device from ever being used (like to download a fixed BIOS). Instead
warn on probe and check again when device is brought up. That way the address
can be set.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Driver for the PA Semi PWRficient on-chip Ethernet (1/10G)

Basic enablement, will be complemented with performance enhancements
over time. PHY support will be added as well.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Removed namespace collisions due to usage of nic_t as per Ralf's patch
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Removed unused code in en_dis_able_nic_intrs(), TX_DMA_INTR, RX_DMA_INTR,
TX_XGXS_INTR, MC_INTR
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

1. Fix for updating skb->truesize properly.
2. Disable NAPI only if more than one ring configured in case of MSI/MSI-X
   interrupts. Previously we were disabling NAPI irrespective of number of
   rings when MSI/MSI-X interrupts were used.
3. Code cleanup.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

1. Fix for reset and link handling.
2. Allow for promiscuos mode and multicast state be maintained through
   ifconfig up and down.
3. Support to print adapter serial number.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch adds two load parameters napi and ufo. Previously NAPI was
compilation option with these changes wan enable disable NAPI using load
parameter. Also we are introducing ufo load parameter to enable/disable
ufo feature
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The attached patch adds an alternative driver "pc300too" for PCI WAN
cards PC300/RSV and PC300/X21 made by Cyclades Corp. (now Avocent Corp).
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Dual licensing, needed for OFED 1.2
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Include <linux/mutex.h> in adapter.h
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

In some cases, SG_DATA_INTR won't clear on read and the following
interrupt may cause us to assert because NAPI is already scheduled.
Remove the assertion, NAPI can handle attempts to rearm it while
it's already scheduled.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Use tabs in comments.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Clean up the tp_config() routine.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Remove a status error string from the pci-x context
and add it where it belongs - the pci-e context.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Remove tx credit coalescing done in SW.
The HW is caring care of it already.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Inform FW about the queue set->interface mapping.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Clean up FW version checking.
The supported FW version is now 3.1.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Cc: "Sunil Naidu" <akula2.shark@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Since it's no longer used, this "#define BCM_TSO 1" can now be removed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

A kmalloc casting cleanup patch.
Signed-off-by: Ahmed Darwish <darwish.07@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

If alloc_etherdev() failed, then sky2_init_netdev will return NULL,
and sky2_probe would end up returning 0 instead of -ENOMEM.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Maintain packet statistics in software rather than hardware.
This is slightly slower, but allows easier debugging of problems
where packets are still being received by PHY but not being handled
by hardware.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Version update to 1.11.1.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

s/FEter/FEther/.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch optimizes the data paths that can support hw counters. It
removes the sw counted statistics.

This is the last patch for the optimization set. Bumping up version of
driver.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch introduces hw statistics for older devices that supported it.
It breaks up the counters supported into separate versions.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch adds a limit to how much tx work can be done in each
iteration of tx processing. If the max limit is reached, remaining tx
completions will be handled by timer interrupt.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch optimizes the irq data paths and cleans up the code.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch optimizes the rx data paths and cleans up the code.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch optimizes the tx data paths and cleans up the code (removes
vlan from descr1/2 since only valid for desc3, changes to make code
easier to read, etc).
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch optimizes the logic for tx limiting. It adds a flag to check
on the completion side instead of recalculating the number of empty
slots. Also, it removes the fields that were previous used for limiting
since they have no value.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch breaks up the routines into two versions, one for legacy
descriptor versions (ver 1 and ver 2) and one for desc ver 3. This will
make the new desc functions more leaner and further reductions will be
made in next few patches.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

	Update version number to reflect recent changes.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

	The existing code would blindly attempt to create the
bonding_masters file (in /sys/class/net) every time the module was
loaded.  When the module is loaded multiple times (which is the
historical method used by initscripts and sysconfig to create multiple
bonding interfaces), this caused load failure of the second module load
attempt, as the creation request would fail.

	This changes the code to note the failure, arrange to not remove
the bonding_masters file upon module exit, and then return success.

	Bonding interfaces created by the second or subsequent loads of
the module will not exist in bonding_masters.  This is not a significant
change, as previously only the interfaces from the most recent load of
the module would be listed.  Both situations are less than optimal, but
this case permits compatibility with existing distro configuration
scripts, and is consistent.

	Note that previously, the sysfs create request would overwrite
the exsting bonding_masters file and succeed, allowing multiple loads of
the module.  The sysfs code has recently changed to return an error if
the file being created already exists.

	Patrick McHardy <kaber@trash.net>, who reported this problem,
observed crashes on the old kernel (before sysfs checked for
duplicates).  I did not experience such crashes, but this change should
resolve them.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

	The existing code did not correctly handle failures to create
the per-interface sysfs group for bonding.

	Modified code to notice errors, and correctly unwind.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

	The code to select names for the bonding interfaces was, for the
non-sysfs creation case, always using a hard-coded set of bond0, bond1,
etc, up to max_bonds.  This caused conflicts for the second or
subsequent loads of the module.

	Changed the code to obtain device names from dev_alloc_name().
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Use bitrev8 for bmac, mace, macmace, macsonic, and skfp drivers.

[akpm@osdl.org: use the API, not the array]
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mirko Lindner <mlindner@syskonnect.de>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

"extern inline" generates a warning with -Wmissing-prototypes and I'm
currently working on getting the kernel cleaned up for adding this to
the CFLAGS since it will help us to avoid a nasty class of runtime
errors.

If there are places that really need a forced inline, __always_inline
would be the correct solution.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>