- 11 Jun, 2014 40 commits
-
-
Dirk Brandewie authored
commit c4ee841f upstream. The PID assumes that samples are of equal time, which for a deferable timers this is not true when the system goes idle. This causes the PID to take a long time to converge to the min P state and depending on the pattern of the idle load can make the P state appear stuck. The hold-off value of three sample times before using the scaling is to give a grace period for applications that have high performance requirements and spend a lot of time idle, The poster child for this behavior is the ffmpeg benchmark in the Phoronix test suite. Signed-off-by:
Dirk Brandewie <dirk.j.brandewie@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dirk Brandewie authored
commit f0fe3cd7 upstream. Changing to fixed point math throughout the busy calculation in commit e66c1768 (Change busy calculation to use fixed point math.) Introduced some inaccuracies by rounding the busy value at two points in the calculation. This change removes roundings and moves the rounding to the output of the PID where the calculations are complete and the value returned as an integer. Fixes: e66c1768 (intel_pstate: Change busy calculation to use fixed point math.) Reported-by:
Doug Smythies <dsmythies@telus.net> Signed-off-by:
-
Dirk Brandewie authored
commit adacdf3f upstream. Commit fcb6a15c (intel_pstate: Take core C0 time into account for core busy calculation) introduced a regression referenced below. The issue with "lockup" after suspend that this commit was addressing is now dealt with in the suspend path. Fixes: fcb6a15c (intel_pstate: Take core C0 time into account for core busy calculation) Link: https://bugzilla.kernel.org/show_bug.cgi?id=66581 Link: https://bugzilla.kernel.org/show_bug.cgi?id=75121Reported-by:
-
Dirk Brandewie authored
commit d37e2b76 upstream. Remove unneeded sample buffers, intel_pstate operates on the most recent sample only. This save some memory and make the code more readable. Signed-off-by:
-
Sebastian Ott authored
commit 0c36b390 upstream. The percpu-refcount infrastructure uses the underscore variants of this_cpu_ops in order to modify percpu reference counters. (e.g. __this_cpu_inc()). However the underscore variants do not atomically update the percpu variable, instead they may be implemented using read-modify-write semantics (more than one instruction). Therefore it is only safe to use the underscore variant if the context is always the same (process, softirq, or hardirq). Otherwise it is possible to lose updates. This problem is something that Sebastian has seen within the aio subsystem which uses percpu refcounters both in process and softirq context leading to reference counts that never dropped to zeroes; even though the number of "get" and "put" calls matched. Fix this by using the non-underscore this_cpu_ops variant which provides correct per cpu atomic semantics and fixes the corrupted reference counts. Cc: Kent Overstreet <kmo@daterainc.com> Reported-by:
Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Tejun Heo <tj@kernel.org> References: http://lkml.kernel.org/g/alpine.LFD.2.11.1406041540520.21183@denkbrettSigned-off-by:
-
Alan Stern authored
commit 8ef42ddd upstream. Not all host controller drivers have bus-suspend and bus-resume methods. When one doesn't, it will cause problems if runtime PM is enabled in the kernel. The PM core will attempt to suspend the controller's root hub, the suspend will fail because there is no bus-suspend routine, and a -EBUSY error code will be returned to the PM core. This will cause the suspend attempt to be repeated shortly thereafter, in a never-ending loop. Part of the problem is that the original error code -ENOENT gets changed to -EBUSY in usb_runtime_suspend(), on the grounds that the PM core will interpret -ENOENT as meaning that the root hub has gotten into a runtime-PM error state. While this change is appropriate for real USB devices, it's not such a good idea for a root hub. In fact, considering the root hub to be in a runtime-PM error state would not be far from the truth. Therefore this patch updates usb_runtime_suspend() so that it adjusts error codes only for non-root-hub devices. Furthermore, the patch attempts to prevent the problem from occurring in the first place by not enabling runtime PM by default for root hubs whose host controller driver doesn't have bus_suspend and bus_resume methods. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Will Deacon <will.deacon@arm.com> Tested-by:
-
Mathias Nyman authored
commit b38f09cc upstream. Sony VAIO t-series machines are not capable of switching usb2 ports over from Intel EHCI to xHCI controller. If tried the USB2 port will be left unconnected and unusable. This patch should be backported to stable kernels as old as 3.12, that contain the commit 26b76798 "Intel xhci: refactor EHCI/xHCI port switching" Reported-by:
Jorge <xxopxe@gmail.com> Tested-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Johan Hovold authored
commit c03890ff upstream. A recent patch that purported to fix firmware download on big-endian machines failed to add the corresponding sparse annotation to the i2c-header. This was reported by the kbuild test robot. Adding the appropriate annotation revealed another endianess bug related to the i2c-header Size-field in a code path that is exercised when the firmware is actually being downloaded (and not just verified and left untouched unless older than the firmware at hand). This patch adds the required sparse annotation to the i2c-header and makes sure that the Size-field is sent in little-endian byte order during firmware download also on big-endian machines. Note that this patch is only compile-tested, but that there is no functional change for little-endian systems. Reported-by:
kbuild test robot <fengguang.wu@intel.com> Cc: Ludovic Drolez <ldrolez@debian.org> Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Alexej Starschenko authored
commit 8a61ba3a upstream. Adds product ID for the Novatel E371 PCI Express Mini Card. $ lsusb Bus 001 Device 024: ID 1410:9011 Novatel Wireless $ usb-devices T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 24 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1410 ProdID=9011 Rev=00.03 S: Manufacturer=Novatel Wireless, Inc. S: Product=Novatel Wireless HSPA S: SerialNumber=012773002115811 C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 6 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#= 7 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether Tested with kernel 3.2.0. Signed-off-by:
Alexej Starschenko <starschenko@gmail.com> Signed-off-by:
-
Greg Kroah-Hartman authored
commit 7ac3764f upstream. The file include/uapi/linux/usb/cdc-wdm.h uses a __u16 so it needs to include types.h as well to make the build system happy. Fixes: 3edce1cf ("USB: cdc-wdm: implement IOCTL_WDM_MAX_COMMAND") Cc: Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Bjørn Mork authored
commit 7d189636 upstream. The include/uapi/linux/usb/cdc-wdm.h header defines cdc-wdm userspace APIs and should be exported by make headers_install. Fixes: 3edce1cf ("USB: cdc-wdm: implement IOCTL_WDM_MAX_COMMAND") Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
George McCollister authored
commit d0839d75 upstream. The NovaTech OrionLXm uses an onboard FTDI serial converter for JTAG and console access. Here is the lsusb output: Bus 004 Device 123: ID 0403:7c90 Future Technology Devices International, Ltd Signed-off-by:
George McCollister <george.mccollister@gmail.com> Signed-off-by:
-
Takashi Iwai authored
commit 192a98e2 upstream. The conversion to a fixup table for Replacer model with ALC260 in commit 20f7d928 took the wrong widget NID for COEF setups. Namely, NID 0x1a should have been used instead of NID 0x20, which is the common node for all Realtek codecs but ALC260. Fixes: 20f7d928 ('ALSA: hda/realtek - Replace ALC260 model=replacer with the auto-parser') Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Ronan Marquet authored
commit e30cf2d2 upstream. Correcion of wrong fixup entries add in commit ca8f0424 to replace static model quirk for PB V7900 laptop (will model). [note: the removal of ALC260_FIXUP_HP_PIN_0F chain is also needed as a part of the fix; otherwise the pin is set up wrongly as a headphone, and user-space (PulseAudio) may be wrongly trying to detect the jack state -- tiwai] Fixes: ca8f0424 ('ALSA: hda/realtek - Add the fixup codes for ALC260 model=will') Signed-off-by:
Ronan Marquet <ronan.marquet@orange.fr> Signed-off-by:
-
Takashi Iwai authored
commit 598e3061 upstream. ASUS A8JN with AD1986A codec seems following the normal EAPD in the normal order (0 = off, 1 = on) unlike other machines with AD1986A. Apply the workaround used for Toshiba laptop that showed the same problem. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=75041Signed-off-by:
-
Samuel Ortiz authored
commit 40b9397a upstream. 0466 was probably meant to be 0644, there's no reason why everyone except root could write there. Signed-off-by:
Samuel Ortiz <sameo@linux.intel.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Sean MacLennan authored
commit 9326c5ca upstream. A sparse error fixup removed a htons() which is required for the driver to function. This patch puts the htons() back and fixes the sparse warning correctly by changing the left side cast. Signed-off-by:
Sean MacLennan <seanm@seanm.ca> Signed-off-by:
-
Ben Hutchings authored
commit 28a821c3 upstream. This function is largely a duplicate of paste_selection() in drivers/tty/vt/selection.c, but with its own selection state. The speakup selection mechanism should really be merged with vt. For now, apply the changes from 'TTY: vt, fix paste_selection ldisc handling', 'tty: Make ldisc input flow control concurrency-friendly', and 'tty: Fix unsafe vt paste_selection()'. References: https://bugs.debian.org/735202 References: https://bugs.debian.org/744015Reported-by:
Paul Gevers <elbrus@debian.org> Reported-and-tested-by:
Jarek Czekalski <jarekczek@poczta.onet.pl> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Ian Abbott authored
commit ffed54dc upstream. I got a patch from the original author, Fred Brooks, to add a small settling delay after setting the AI channel multiplexor. The lack of delay resulted in unstable or scrambled data on faster processors. Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Reported-by:
Fred Brooks <nsaspook@nsaspook.com> Signed-off-by:
-
Ben Hutchings authored
commit d7500135 upstream. Input is handled in softirq context, but when pasting we may need to sleep. speakup_paste_selection() currently tries to bodge this by busy-waiting if in_atomic(), but that doesn't help because the ldisc may also sleep. For bonus breakage, speakup_paste_selection() changes the state of current, even though it's not running in process context. Move it into a work item and make sure to cancel it on exit. References: https://bugs.debian.org/735202 References: https://bugs.debian.org/744015Reported-by:
-
Mathias Nyman authored
commit 5dc2808c upstream. Lists of endpoints are stored for bandwidth calculation for roothub ports. Make sure we remove all endpoints from the list before the whole device, containing its endpoints list_head stuctures, is freed. This used to be done in the wrong order in xhci_mem_cleanup(), and triggered an oops in resume from S4 (hibernate). Tested-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
NeilBrown authored
commit 2ac295a5 upstream. Commit 8313b8e5 md: fix problem when adding device to read-only array with bitmap. added a called to md_reap_sync_thread() which cause a reshape thread to be interrupted (in particular, it could cause md_thread() to never even call md_do_sync()). However it didn't set MD_RECOVERY_INTR so ->finish_reshape() would not know that the reshape didn't complete. This only happens when mddev->ro is set and normally reshape threads don't run in that situation. But raid5 and raid10 can start a reshape thread during "run" is the array is in the middle of a reshape. They do this even if ->ro is set. So it is best to set MD_RECOVERY_INTR before abortingg the sync thread, just in case. Though it rare for this to trigger a problem it can cause data corruption because the reshape isn't finished properly. So it is suitable for any stable which the offending commit was applied to. (3.2 or later) Fixes: 8313b8e5Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
NeilBrown authored
commit 3991b31e upstream. If mddev->ro is set, md_to_sync will (correctly) abort. However in that case MD_RECOVERY_INTR isn't set. If a RESHAPE had been requested, then ->finish_reshape() will be called and it will think the reshape was successful even though nothing happened. Normally a resync will not be requested if ->ro is set, but if an array is stopped while a reshape is on-going, then when the array is started, the reshape will be restarted. If the array is also set read-only at this point, the reshape will instantly appear to success, resulting in data corruption. Consequently, this patch is suitable for any -stable kernel. Signed-off-by:
-
Richard Weinberger authored
commit b14ed2c2 upstream. attr.sched_policy is u32, therefore a comparison against < 0 is never true. Fix this by casting sched_policy to int. This issue was reported by coverity CID 1219934. Fixes: dbdb2275 ("sched: Disallow sched_attr::sched_policy < 0") Signed-off-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
Peter Zijlstra <peterz@infradead.org> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/1401741514-7045-1-git-send-email-richard@nod.atSigned-off-by:
Ingo Molnar <mingo@kernel.org> Cc: Dave Jones <davej@redhat.com> Signed-off-by:
-
Martin K. Petersen authored
commit 3b8d2676 upstream. Queued trim only works for some users with MU05 firmware. Revert to blacklisting all firmware versions. Introduced by commit d121f7d0 ("libata: Update queued trim blacklist for M5x0 drives") which this effectively reverts, while retaining the blacklisting of M550. See https://bugzilla.kernel.org/show_bug.cgi?id=71371 for reports of trouble with MU05 firmware. Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Tejun Heo <tj@kernel.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Christian König authored
commit 91b0275c upstream. The SDMA sometimes doesn't seem to work reliable. Signed-off-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 3640da2f upstream. Setting the power state prior to restoring the display hardware leads to blank screens on some systems. Drop the power state set from dpm resume. The power state will get set as part of the mode set sequence. Also add an explicit power state set after mode set resume to cover PX and headless systems. bug: https://bugzilla.kernel.org/show_bug.cgi?id=76761Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Chris Wilson authored
commit 9aab8bff upstream. We only want to modifiy a single field in the userspace view of the execbuffer command buffer, so explicitly change that rather than copy everything back again. This serves two purposes: 1. The single fields are much cheaper to copy (constant size so the copy uses special case code) and much smaller than the whole array. 2. We modify the array for internal use that need to be masked from the user. Note: We need this backported since without it the next bugfix will blow up when userspace recycles batchbuffers and relocations. Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Christian König authored
commit 60a44540 upstream. Signed-off-by:
-
Kirill Tkhai authored
commit 0f397f2c upstream. Throttled task is still on rq, and it may be moved to other cpu if user is playing with sched_setaffinity(). Therefore, unlocked task_rq() access makes the race. Juri Lelli reports he got this race when dl_bandwidth_enabled() was not set. Other thing, pointed by Peter Zijlstra: "Now I suppose the problem can still actually happen when you change the root domain and trigger a effective affinity change that way". To fix that we do the same as made in __task_rq_lock(). We do not use __task_rq_lock() itself, because it has a useful lockdep check, which is not correct in case of dl_task_timer(). We do not need pi_lock locked here. This case is an exception (PeterZ): "The only reason we don't strictly need ->pi_lock now is because we're guaranteed to have p->state == TASK_RUNNING here and are thus free of ttwu races". Signed-off-by:
Kirill Tkhai <tkhai@yandex.ru> Signed-off-by:
-
Lai Jiangshan authored
commit 6acbfb96 upstream. Lai found that: WARNING: CPU: 1 PID: 13 at arch/x86/kernel/smp.c:124 native_smp_send_reschedule+0x2d/0x4b() ... migration_cpu_stop+0x1d/0x22 was caused by set_cpus_allowed_ptr() assuming that cpu_active_mask is always a sub-set of cpu_online_mask. This isn't true since 5fbd036b ("sched: Cleanup cpu_active madness"). So set active and online at the same time to avoid this particular problem. Fixes: 5fbd036b ("sched: Cleanup cpu_active madness") Signed-off-by:
Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by:
-
Juri Lelli authored
commit b0827819 upstream. Michael Kerrisk noticed that creating SCHED_DEADLINE reservations with certain parameters (e.g, a runtime of something near 2^64 ns) can cause a system freeze for some amount of time. The problem is that in the interface we have u64 sched_runtime; while internally we need to have a signed runtime (to cope with budget overruns) s64 runtime; At the time we setup a new dl_entity we copy the first value in the second. The cast turns out with negative values when sched_runtime is too big, and this causes the scheduler to go crazy right from the start. Moreover, considering how we deal with deadlines wraparound (s64)(a - b) < 0 we also have to restrict acceptable values for sched_{deadline,period}. This patch fixes the thing checking that user parameters are always below 2^63 ns (still large enough for everyone). It also rewrites other conditions that we check, since in __checkparam_dl we don't have to deal with deadline wraparounds and what we have now erroneously fails when the difference between values is too big. Reported-by:
Michael Kerrisk <mtk.manpages@gmail.com> Suggested-by:
Juri Lelli <juri.lelli@gmail.com> Signed-off-by:
-
Peter Zijlstra authored
commit ce5f7f82 upstream. The way we read POSIX one should only call sched_getparam() when sched_getscheduler() returns either SCHED_FIFO or SCHED_RR. Given that we currently return sched_param::sched_priority=0 for all others, extend the same behaviour to SCHED_DEADLINE. Requested-by:
-
Michael Kerrisk authored
commit 143cf23d upstream. The documented[1] behavior of sched_attr() in the proposed man page text is: sched_attr::size must be set to the size of the structure, as in sizeof(struct sched_attr), if the provided structure is smaller than the kernel structure, any additional fields are assumed '0'. If the provided structure is larger than the kernel structure, the kernel verifies all additional fields are '0' if not the syscall will fail with -E2BIG. As currently implemented, sched_copy_attr() returns -EFBIG for for this case, but the logic in sys_sched_setattr() converts that error to -EFAULT. This patch fixes the behavior. [1] http://thread.gmane.org/gmane.linux.kernel/1615615/focus=1697760Signed-off-by:
-
Peter Zijlstra authored
commit dbdb2275 upstream. The scheduler uses policy=-1 to preserve the current policy state to implement sys_sched_setparam(), this got exposed to userspace by accident through sys_sched_setattr(), cure this. Reported-by:
-
Ming Lei authored
commit aa0818c6 upstream. When there isn't enough vring descriptor for adding to vq, blk-mq will be put as stopped state until some of pending descriptors are completed & freed. Unfortunately, the vq's interrupt may come just before blk-mq's BLK_MQ_S_STOPPED flag is set, so the blk-mq will still be kept as stopped even though lots of descriptors are completed and freed in the interrupt handler. The worst case is that all pending descriptors are freed in the interrupt handler, and the queue is kept as stopped forever. This patch fixes the problem by starting/stopping blk-mq with holding vq_lock. Cc: Jens Axboe <axboe@kernel.dk> Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
Ming Lei <tom.leiming@gmail.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Greg Kroah-Hartman authored
This reverts commit 62376251. Ben rightly points out that commit 0bf1457f, which is what this original commit was reverting, never ended up in 3.14-stable, but was only for 3.15. So revert this patch as we now have the same check twice in a row, which is pretty pointless. Although the comments were "prettier"... Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Rafael Aquini <aquini@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Heinz Mauelshagen authored
commit f1daa838 upstream. The DM cache target cannot cope with discards that span multiple cache blocks, so each discard bio that spans more than one cache block must get split by the DM core. Signed-off-by:
Heinz Mauelshagen <heinzm@redhat.com> Acked-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Mike Snitzer authored
commit 80c57893 upstream. Commit 85ad643b ("dm thin: add timeout to stop out-of-data-space mode holding IO forever") introduced a fixed 60 second timeout. Users may want to either disable or modify this timeout. Allow the out-of-data-space timeout to be configured using the 'no_space_timeout' dm-thin-pool module param. Setting it to 0 will disable the timeout, resulting in IO being queued until more data space is added to the thin-pool. Signed-off-by:
-
Markos Chandras authored
commit 721a9205 upstream. Introduced by the following two commits: 75b5b5e0 "MIPS: Add support for FTLBs" 6de20451 "MIPS: Add printing of ES bit for Imgtec cores when cache error occurs" Signed-off-by:
Markos Chandras <markos.chandras@imgtec.com> Reported-by:
Matheus Almeida <Matheus.Almeida@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Markos Chandras <markos.chandras@imgtec.com> Patchwork: https://patchwork.linux-mips.org/patch/6980/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
