Allow specifying dmic data pins through device-properties / dt. This will
allow us to stop exporting rt5640_dmic_enable() once all callers of it have
been converted to setting device-properties for this instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

On some platforms the platform code may need to add device-properties,
rather then relying only on properties set by the firmware.

This commit moves the parsing of the device-properties from the i2c-driver
probe() function, which may be called at any time, to the component-driver
probe() function, which gets called after the platform code calls
snd_soc_register_card().

This allows the platform code to attach extra device-properties before
the device-properties are parsed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

There are no in tree users of platform-data for the rt5640 codec driver,
so lets remove support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add devicetree-bindings for the dmic, jack-detect source and overcurrent-
detect threshold settings.

The dmic bindings mirror the existing bindings for the rt5645.
The jd-src and ovcd bindings mirror the existing bindings for the rt5651.

Cc devicetree@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

is_sys_clk_from_pll() is used as a snd_soc_dapm_route.connected callback,
checking RT5640_GBL_CLK to determine if the sys-clk is PLL1 and thus the
PWR_PLL bit in reg PWR_ANLG2 must be set.

RT5640_GBL_CLK is changed by rt5640_set_dai_sysclk(), which gets called by
the pre_pmu / post_pmd functions of the "Platform Clock" dapm-supply.

This creates an ordering issue, during a dapm transition first all
connected() callbacks are called to build a list of supplies to enable
and then the complete list is walked to enable the supplies. Since the
connected() check happens before enabling any supplies,
is_sys_clk_from_pll() ends up deciding if the PWR_PLL bit should be set
based on the state the "Platform Clock" supply had *before* the transition.
This sometimes results in PWR_PLL being off, even though *after* the
transition PLL1 is configured as sys-clk.

This commit removes is_sys_clk_from_pll() instead simply setting / clearing
PWR_PLL in rt5640_set_dai_sysclk() based on the selected sys-clk, which
fixes this and as a bonus results in a nice cleanup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Trivial fix to spelling mistake in dev_err message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds controllers for digital volume of PCM output. Volume
effects simply linear, not dB scale as follows:
  Gained PCM = Original * 0x4000 / Volume

The value range of volume is from 0x0001 to 0xffff. 0x0000 works as
mute. Initial value is 0x4000 (+0dB).
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

We can get legacy dai name flag from component driver.
Thus, there is no need to have its parameter on snd_soc_register_dais().
Let's remove unneeded parameter
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

There is no user to call snd_soc_component_add_unlocked() anymore.
Let's merge snd_soc_component_add_unlocked() and
snd_soc_component_add().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

commit ef050bec ("ASoC: Remove platform code now everything is
componentised") removed platform code, but it didn't care
about platform documentation.
This patch convert platform explanation to component
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

commit ef050bec ("ASoC: Remove platform code now everything is
componentised") removed platform code, then platform_list_show() was
removed, too. But we want to keep it as component_list_show.
This patch add it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Now no one is using Codec related code.
Let's remove all
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

commit ef050bec ("ASoC: Remove platform code now everything is
componentised") removed platform code, but it didn't remove
.pcm_new/free which existed only for platform.
This patch remove these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
Now, no one is using .get_regmap, let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Codec reg_cache is legacy feature, almost all driver are now using
common regmap, and very few driver had been used this legacy feature.
Because of this background, it is now implemented on each
driver internally now.
So now, no one is using codec reg_cache. Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

No one is using codec hw_write/control_data any more.
Let's remove these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use the new platform driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use the new platform driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use the new platform driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use the new platform driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

With the generic dmaengine_pcm support the omap-cpm can be replaced with a
much smaller wrapper.

CPU DAI drivers can use the:
int sdma_pcm_platform_register(struct device *dev,
			       char *txdmachan, char *rxdmachan);

To register the platform driver, txdmachan/rxdmachan is only needed to be
provided if the DMA channel names are not standard tx/rx, like in case of
McPDM, or the DAI is only capable of one audio direction (DMIC, HDMI).

This patch only introduces the source file and changes to the
Kconfig/Makefile, but does not change any of the DAI drivers to use it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch replaces mixer switch to DAPM one for changing audio source
of line-in.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Trivial fix to spelling mistake in dev_warn messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

In case of error, the function dev_get_regmap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Now we can replace Codec to Component. Let's do it.

Note:
	xxx_codec_xxx()		->	xxx_component_xxx()
	.idle_bias_off = 0	->	.idle_bias_on = 1
	.ignore_pmdown_time = 0	->	.use_pmdown_time = 1
	-			->	.endianness = 1
	-			->	.non_legacy_dai_naming = 1
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

The patch optimizes the power consumption.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

According to Devicetree Specification v0.2 document:

"The name of a node should be somewhat generic, reflecting the function
of the device and not its precise programming model."

Do as suggested in the binding example.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

According to Devicetree Specification v0.2 document:

"The name of a node should be somewhat generic, reflecting the function
of the device and not its precise programming model."

Do as suggested in the binding example.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

According to Devicetree Specification v0.2 document:

"The name of a node should be somewhat generic, reflecting the function
of the device and not its precise programming model."

Do as suggested in the binding example.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

According to Devicetree Specification v0.2 document:

"The name of a node should be somewhat generic, reflecting the function
of the device and not its precise programming model."

Do as suggested in the binding example.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The TAS6424 incorporates both DC-load and AC-load diagnostics which are
used to determine the status of the load. The DC diagnostics runs when any
channel is directed to leave the Hi-Z state and enter the MUTE or PLAY
state.
The DC diagnostics are turned on by default but, if a fast startup without
diagnostics is required, the diagnostics can be disabled using a dedicated
ALSA control.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Organize the paths of the mixer, "Input Boost Stage", including
the routes of the mixer. The control is not used correctly before.
Besides, the driver changes the name of the mixer controls.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

conflict between a fix and new development in mtk

At the moment playback_active and capture_active are using only 1 bit so
the maximum active count is 1.

However, snd_soc_runtime_activate() may be called several time on the
same dai. This happens when a dai is part of several dai_links. It is
often the case for "snd-soc-dummy-dai".

This is a problem if snd_soc_runtime_activate() is called an even number
of times on a dai. In this case the active count overflow back to 0. As
consequence, ASoC functions, such as soc_dpcm_runtime_update(), won't run
correctly.

Storing these usage counts on plain 'unsigned int' solves the problem.

Fixes: f0fba2ad ("ASoC: multi-component - ASoC Multi-Component Support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

According to "EP93xx User’s Guide", I2STXLinCtrlData and I2SRXLinCtrlData
registers actually have different format. The only currently used bit
(Left_Right_Justify) has different position. Fix this and simplify the
whole setup taking into account the fact that both registers have zero
default value.

The practical effect of the above is repaired SND_SOC_DAIFMT_RIGHT_J
support (currently unused).
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org