1. 02 May, 2017 10 commits
  2. 02 Apr, 2017 2 commits
    • Xiubo Li's avatar
      tcmu: Skip Data-Out blocks before gathering Data-In buffer for BIDI case · a5d68ba8
      Xiubo Li authored
      For the bidirectional case, the Data-Out buffer blocks will always at
      the head of the tcmu_cmd's bitmap, and before gathering the Data-In
      buffer, first of all it should skip the Data-Out ones, or the device
      supporting BIDI commands won't work.
      
      Fixed: 26418649 ("target/user: Introduce data_bitmap, replace
      		data_length/data_head/data_tail")
      Reported-by: default avatarIlias Tsitsimpis <iliastsi@arrikto.com>
      Tested-by: default avatarIlias Tsitsimpis <iliastsi@arrikto.com>
      Signed-off-by: default avatarXiubo Li <lixiubo@cmss.chinamobile.com>
      Cc: stable@vger.kernel.org # 4.6+
      Signed-off-by: default avatarNicholas Bellinger <nab@linux-iscsi.org>
      a5d68ba8
    • Nicholas Bellinger's avatar
      iscsi-target: Drop work-around for legacy GlobalSAN initiator · 1c99de98
      Nicholas Bellinger authored
      Once upon a time back in 2009, a work-around was added to support
      the GlobalSAN iSCSI initiator v3.3 for MacOSX, which during login
      did not propose nor respond to MaxBurstLength, FirstBurstLength,
      DefaultTime2Wait and DefaultTime2Retain keys.
      
      The work-around in iscsi_check_proposer_for_optional_reply()
      allowed the missing keys to be proposed, but did not require
      waiting for a response before moving to full feature phase
      operation.  This allowed GlobalSAN v3.3 to work out-of-the
      box, and for many years we didn't run into login interopt
      issues with any other initiators..
      
      Until recently, when Martin tried a QLogic 57840S iSCSI Offload
      HBA on Windows 2016 which completed login, but subsequently
      failed with:
      
          Got unknown iSCSI OpCode: 0x43
      
      The issue was QLogic MSFT side did not propose DefaultTime2Wait +
      DefaultTime2Retain, so LIO proposes them itself, and immediately
      transitions to full feature phase because of the GlobalSAN hack.
      However, the QLogic MSFT side still attempts to respond to
      DefaultTime2Retain + DefaultTime2Wait, even though LIO has set
      ISCSI_FLAG_LOGIN_NEXT_STAGE3 + ISCSI_FLAG_LOGIN_TRANSIT
      in last login response.
      
      So while the QLogic MSFT side should have been proposing these
      two keys to start, it was doing the correct thing per RFC-3720
      attempting to respond to proposed keys before transitioning to
      full feature phase.
      
      All that said, recent versions of GlobalSAN iSCSI (v5.3.0.541)
      does correctly propose the four keys during login, making the
      original work-around moot.
      
      So in order to allow QLogic MSFT to run unmodified as-is, go
      ahead and drop this long standing work-around.
      Reported-by: default avatarMartin Svec <martin.svec@zoner.cz>
      Cc: Martin Svec <martin.svec@zoner.cz>
      Cc: Himanshu Madhani <Himanshu.Madhani@cavium.com>
      Cc: Arun Easi <arun.easi@cavium.com>
      Cc: stable@vger.kernel.org # 3.1+
      Signed-off-by: default avatarNicholas Bellinger <nab@linux-iscsi.org>
      1c99de98
  3. 31 Mar, 2017 5 commits
  4. 30 Mar, 2017 6 commits
  5. 19 Mar, 2017 14 commits
  6. 18 Mar, 2017 3 commits
    • Nicholas Bellinger's avatar
      tcmu: Convert cmd_time_out into backend device attribute · 7d7a7435
      Nicholas Bellinger authored
      Instead of putting cmd_time_out under ../target/core/user_0/foo/control,
      which has historically been used by parameters needed for initial
      backend device configuration, go ahead and move cmd_time_out into
      a backend device attribute.
      
      In order to do this, tcmu_module_init() has been updated to create
      a local struct configfs_attribute **tcmu_attrs, that is based upon
      the existing passthrough_attrib_attrs along with the new cmd_time_out
      attribute.  Once **tcm_attrs has been setup, go ahead and point
      it at tcmu_ops->tb_dev_attrib_attrs so it's picked up by target-core.
      
      Also following MNC's previous change, ->cmd_time_out is stored in
      milliseconds but exposed via configfs in seconds.  Also, note this
      patch restricts the modification of ->cmd_time_out to before +
      after the TCMU device has been configured, but not while it has
      active fabric exports.
      
      Cc: Mike Christie <mchristi@redhat.com>
      Signed-off-by: default avatarNicholas Bellinger <nab@linux-iscsi.org>
      7d7a7435
    • Mike Christie's avatar
      tcmu: make cmd timeout configurable · af980e46
      Mike Christie authored
      A single daemon could implement multiple types of devices
      using multuple types of real devices that may not support
      restarting from crashes and/or handling tcmu timeouts. This
      makes the cmd timeout configurable, so handlers that do not
      support it can turn if off for now.
      Signed-off-by: default avatarMike Christie <mchristi@redhat.com>
      Signed-off-by: default avatarNicholas Bellinger <nab@linux-iscsi.org>
      af980e46
    • Mike Christie's avatar
      tcmu: add helper to check if dev was configured · 972c7f16
      Mike Christie authored
      This adds a helper to check if the dev was configured. It
      will be used in the next patch to prevent updates to some
      config settings after the device has been setup.
      Signed-off-by: default avatarMike Christie <mchristi@redhat.com>
      Signed-off-by: default avatarNicholas Bellinger <nab@linux-iscsi.org>
      972c7f16