If oui were a null variable then vic_provinfo_alloc() would leak memory.
But this function is only called from one place and oui is not null so
I removed the check.

I also moved the memory allocation down a line so it was easier to spot.
(No one ever reads variable declarations).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The point of using the devres resource management routines is that they
simplify the driver by taking care of releasing resources on failure and
release.  A recent commit added a bunch of error handling that is unnecessary
in this context.

This patch removes this redundant error handling, as well as using
dmam_alloc_coherent in place of dma_alloc_coherent in order to use this
framework consistenly throughout the driver.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

This matches what ethoc_mdio_read does and makes the functions
symmetric.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

- No need to iterate over all possible addresses on bus
- Use helper function phy_find_first
- Use phy_connect_direct as we already have the relevant structure
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

This moves the write of the TX_BD_NUM to init_ring together with the
rest of the code setting up the transmission buffers.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethoc driver should be writing bus addresses to the ethoc registers, not
virtual addresses.  This patch adds an array to store the virtual addresses
in and references that array when manipulating the contents of the buffer
descriptors.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

This moves the calculation of the number of transmission buffers to
ethoc_probe where it more logically fits with the rest of the memory
allocation code.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

i2400m_fw_hdr_check() was accessing hardware field
bcf_hdr->module_type (little endian 32) without converting to host
byte sex.
Reported-by: Данилин Михаил <mdanilin@nsg.net.ru>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>

Conflicts:
	drivers/net/wireless/wl12xx/wl1271.h
	drivers/net/wireless/wl12xx/wl1271_cmd.h

remove useless union keyword in rtable, rt6_info and dn_route.

Since there is only one member in a union, the union keyword isn't useful.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fix a race at the end of NAPI complete processing, it had
better do __napi_complete() first before re-enable interrupt.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch correct a bug in the delay of pktgen. 
It makes sure the inter-packet interval is accurate.
Signed-off-by: Daniel Turull <daniel.turull@gmail.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

gen_kill_estimator() / gen_new_estimator() is not always called with
RTNL held.

net/netfilter/xt_RATEEST.c is one user of these API that do not hold
RTNL, so random corruptions can occur between "tc" and "iptables".

Add a new fine grained lock instead of trying to use RTNL in netfilter.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 66018506 (ip: Router Alert RCU conversion) introduced RCU
lookups to ip_call_ra_chain(). It missed proper deinit phase :
When ip_ra_control() deletes an ip_ra_chain, it should make sure
ip_call_ra_chain() users can not start to use socket during the rcu
grace period. It should also delay the sock_put() after the grace
period, or we risk a premature socket freeing and corruptions, as
raw sockets are not rcu protected yet.

This delay avoids using expensive atomic_inc_not_zero() in
ip_call_ra_chain().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the accelerated receive path for VLAN's will
drop packets if the real device is an inactive slave and
is not one of the special pkts tested for in
skb_bond_should_drop().  This behavior is different then
the non-accelerated path and for pkts over a bonded vlan.

For example,

vlanx -> bond0 -> ethx

will be dropped in the vlan path and not delivered to any
packet handlers at all.  However,

bond0 -> vlanx -> ethx

and

bond0 -> ethx

will be delivered to handlers that match the exact dev,
because the VLAN path checks the real_dev which is not a
slave and netif_recv_skb() doesn't drop frames but only
delivers them to exact matches.

This patch adds a sk_buff flag which is used for tagging
skbs that would previously been dropped and allows the
skb to continue to skb_netif_recv().  Here we add
logic to check for the deliver_no_wcard flag and if it
is set only deliver to handlers that match exactly.  This
makes both paths above consistent and gives pkt handlers
a way to identify skbs that come from inactive slaves.
Without this patch in some configurations skbs will be
delivered to handlers with exact matches and in others
be dropped out right in the vlan path.

I have tested the following 4 configurations in failover modes
and load balancing modes.

# bond0 -> ethx

# vlanx -> bond0 -> ethx

# bond0 -> vlanx -> ethx

# bond0 -> ethx
            |
  vlanx -> --
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 1f8438a8 (icmp: Account for ICMP out errors), I did a typo
on IPV6 side, using ICMP6_MIB_OUTMSGS instead of ICMP6_MIB_OUTERRORS
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- ipv6_sock_mc_join() : doesnt touch dev refcount

- ipv6_sock_mc_drop() : doesnt touch dev/idev refcounts

- ip6_mc_find_dev() becomes ip6_mc_find_dev_rcu() (called from rcu),
                    and doesnt touch dev/idev refcounts

- ipv6_sock_mc_close() : doesnt touch dev/idev refcounts

- ip6_mc_source() uses ip6_mc_find_dev_rcu()

- ip6_mc_msfilter() uses ip6_mc_find_dev_rcu()

- ip6_mc_msfget() uses ip6_mc_find_dev_rcu()

- ipv6_dev_mc_dec(), ipv6_chk_mcast_addr(),
  igmp6_event_query(), igmp6_event_report(),
  mld_sendpack(), igmp6_send() dont touch idev refcount
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need for pppoe_xmit() forward declaration in
drivers/net/pppoe.c. This patch removes this  pppoe_xmit() declaration.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- rcu_read_lock() already held by caller
- use __in_dev_get_rcu() instead of in_dev_get() / in_dev_put()
- remove goto out;
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Realtek confirmed that a 20us delay is needed after mdio_read and
mdio_write operations. Reduce the delay in mdio_write, and add it
to mdio_read too. Also add a comment that the 20us is from hw specs.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit cc772ab7 ("gianfar: Add
hardware RX timestamping support"), the driver no longer works on
at least MPC8313ERDB and MPC8568EMDS boards (and possibly much more
boards as well).

That's how MPC8313 Reference Manual describes RCTRL_TS_ENABLE bit:

  Timestamp incoming packets as padding bytes. PAL field is set
  to 8 if the PAL field is programmed to less than 8. Must be set
  to zero if TMR_CTRL[TE]=0.

I see that the commit above sets this bit, but it doesn't handle
TMR_CTRL. Manfred probably had this bit set by the firmware for
his boards. But obviously this isn't true for all boards in the
wild.

Also, I recall that Freescale BSPs were explicitly disabling the
timestamping because of a performance drop.

For now, the best way to deal with this is just disable the
timestamping, and later we can discuss proper device tree bindings
and implement enabling this feature via some property.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The extra ! character means that these conditions are always false.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements a work around for Erratum 5, "3.3 V Fiber Speed
Selection." If the hardware wiring does not respect this erratum, then
fiber optic mode will not work properly.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use call_rcu rather than synchronize_rcu.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

BugLink: http://bugs.launchpad.net/bugs/591416

There are a number of network drivers (bridge, bonding, etc) that are not yet
receive multi-queue enabled and use alloc_netdev(), so don't print a
num_rx_queues imbalance warning in that case.

Also, only print the warning once for those drivers that _are_ multi-queue
enabled.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>

When we receive a deauthentication frame before
having successfully associated, we neither print
a message nor abort assocation. The former makes
it hard to debug, while the latter later causes
a warning in cfg80211 when, as will typically be
the case, association timed out.

This warning was reported by many, e.g. in
https://bugzilla.kernel.org/show_bug.cgi?id=15981,
but I couldn't initially pinpoint it. I verified
the fix by hacking hostapd to send a deauth frame
instead of an association response.

Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Using ieee80211_find_sta() needs to be under
RCU read lock, which iwlwifi currently misses,
so fix it.

Cc: stable@kernel.org
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reading the ELP_CTRL register with sdio_readb causes problems because
hardware seems to be performing a write using stuff bits in the request
(those bits contain write data in write request). This indicates that it
actually expects RAW (read after write) type of request, so perform that
when reading ELP_CTRL instead. Also cache last written value so we know
what to write when doing RAW request.

Because of the above it was not possible to wake the chip from ELP power
saving mode, PM had to be disabled to have the driver usable in SDIO
mode. After this patch PM is functional.

For backporting to 2.6.34 or earlier, this patch depends on
6c1f716e, which adds the
required SDIO funcion.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix a whole bunch of kernel-doc warnings
and errors that crop up when running it on
mac80211 and cfg80211; the latter isn't
normally done so lots of bit-rot happened.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There's a window for ieee80211_ifa_changed() to get called whilst the
managed mode mutex has not been initialized when opening and stopping the
interface. Currently this causes a kernel BUG like the following:

[  132.460013] kernel BUG at /home/wifi/iwlwifi-2.6/net/mac80211/main.c:380!
[  132.460013] invalid opcode: 0000 [#1] SMP

The mutex is initialized during open(), hence once netif_running() is true,
the mutex should be valid. Fix by adding a netif_running() check to the
function.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since ath5k_hw_set_antenna_mode() always writes the default antenna register
and is called at the end of reset, there is no need to separately save and
restore the default antenna.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Collect all pieces concering the antenna switch table into one function.
Previously it was split up between ath5k_hw_reset() and
ath5k_hw_commit_eeprom_settings().

Also we need to set the antenna switch table when ath5k_hw_set_antenna_mode()
is called manually (by "iw phy0 antenna set", for example).

I'm not sure if we need to set the switchtable at the same place in
ath5k_hw_reset() as it was before - it is set later thru
ath5k_hw_set_antenna_mode() anyways - but i leave it there to avoid
problems(?).

Plus print switchtable registers in the debugfs file.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

#define AR5K_PHY_RESTART_DIV_GC               0x001c0000
is 3 bit wide.

The previous values of 0xc and 0x8 are 4bit wide and bigger than the mask.

Writing 0 and 1 to AR5K_PHY_RESTART_DIV_GC is consistent with the comments and
initvals we have in the HAL.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes the libertas driver incorrectly reporting that Wake-on-LAN
is not supported if Wake-on-LAN is currently disabled.
Signed-off-by: Sascha Silbe <sascha-pgp@silbe.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>