W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to all the ATM modules and drivers.

Link: https://lore.kernel.org/r/20240104143737.1317945-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jiri Pirko says:

====================
dpll: expose fractional frequency offset value to user

Allow to expose pin fractional frequency offset value over new DPLL
generic netlink attribute. Add an op to get the value from the driver.
Implement this new op in mlx5 driver.
====================

Link: https://lore.kernel.org/r/20240103132838.1501801-1-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Implement ffo_get() pin op filling it up to MSEED.frequency_diff value.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Acked-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://lore.kernel.org/r/20240103132838.1501801-4-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Instead of passing separate args, introduce
struct mlx5_dpll_synce_status to hold the values obtained by
mlx5_dpll_synce_status_get().
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Acked-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://lore.kernel.org/r/20240103132838.1501801-3-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add a new netlink attribute to expose fractional frequency offset value
for a pin. Add an op to get the value from the driver.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Acked-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://lore.kernel.org/r/20240103132838.1501801-2-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Vladimir Oltean says:

====================
ds->user_mii_bus cleanup (part 1)

There are some drivers which assign ds->user_mii_bus when they
don't really need its specific functionality, aka non-OF based
dsa_user_phy_connect(). There was some confusion regarding the
fact that yes, this is why ds->user_mii_bus really exists, so
I've started a cleanup series which aims to eliminate the usage
of ds->user_mii_bus from drivers when there is nothing to gain
from it.

Today's drivers are lantiq_gswip, qca8k and bcm_sf2. The work is
not done here, but a "part 2" may or may not come, depending on
other priorities.

All patches were only compile-tested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There used to be a of_node_put(priv->master_mii_dn) call in
bcm_sf2_mdio_unregister(), which was accidentally deleted in commit
6ca80638 ("net: dsa: Use conduit and user terms").

But it's not needed - we don't need to hold a reference on the
"brcm,unimac-mdio" OF node for that long, since we don't do anything
with it. We can release it as soon as we finish bcm_sf2_mdio_register().

Also reduce "if (err && dn)" to just "if (err)". We know "dn", aka the
former priv->master_mii_dn, is non-NULL. Otherwise, of_mdio_find_bus(dn)
would not have been able to find the bus behind "brcm,unimac-mdio".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bcm_sf2 driver does something strange. Instead of calling
of_mdiobus_register() with an OF node argument, it manually assigns the
bus->dev->of_node and then calls the non-OF mdiobus_register(). This
circumvents some code from __of_mdiobus_register() from running, which
sets the auto-scan mask, parses some device tree properties, etc.

I'm going to go out on a limb and say that the OF node isn't, in fact,
needed at all, and can be removed. The MDIO diversion as initially
implemented in commit 461cd1b0 ("net: dsa: bcm_sf2: Register our
slave MDIO bus") looked quite different than it is now, after commit
771089c2 ("net: dsa: bcm_sf2: Ensure that MDIO diversion is used").
Initially, it made sense, as bcm_sf2 was registering another set of
driver ops for the "brcm,unimac-mdio" OF node. But now, it deletes all
phandles, which makes "phy-handle"s unable to find PHYs, which means
that it always goes through the OF-unaware dsa_user_phy_connect().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Accessed either through priv->dev or ds->dev, it is the same device
structure. Keep a single variable which holds a reference to it, and use
it consistently.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

__of_mdiobus_register() already calls __mdiobus_register() if the
OF node provided as argument is NULL. We can take advantage of that
and simplify the 2 code path, calling devm_of_mdiobus_register() only
once for both cases.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To simplify reasoning about why the DSA framework provides the
ds->user_mii_bus functionality, drivers should only use it if they
need to. The qca8k driver appears to also use it simply as storage
for a pointer, which is not a good enough reason to make the core
much more difficult to follow.

ds->user_mii_bus is useful for only 2 cases:

1. The driver probes on platform_data (no OF)
2. The driver probes on OF, but there is no OF node for the MDIO bus.

It is unclear if case (1) is supported with qca8k. It might not be:
the driver might crash when of_device_get_match_data() returns NULL
and then it dereferences priv->info without NULL checking.

Anyway, let us limit the ds->user_mii_bus usage only to the above cases,
and not assign it when an OF node is present.

The bus->phy_mask assignment follows along with the movement, because
__of_mdiobus_register() overwrites this bus field anyway. The value set
by the driver only matters for the non-OF code path.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the driver calls the non-OF devm_mdiobus_register() rather
than devm_of_mdiobus_register() for this case, but it seems to rather
be a confusing coincidence, and not a real use case that needs to be
supported.

If the device tree says status = "disabled" for the MDIO bus, we
shouldn't need an MDIO bus at all. Instead, just exit as early as
possible and do not call any MDIO API.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

of_get_child_by_name() gives us an OF node with an elevated refcount,
which should be dropped when we're done with it. This is so that,
if (of_node_check_flag(node, OF_DYNAMIC)) is true, the node's memory can
eventually be freed.

There are 2 distinct paths to be considered in qca8k_mdio_register():

- devm_of_mdiobus_register() succeeds: since commit 3b73a7b8 ("net:
  mdio_bus: add refcounting for fwnodes to mdiobus"), the MDIO core
  treats this well.

- devm_of_mdiobus_register() or anything up to that point fails: it is
  the duty of the qca8k driver to release the OF node.

This change addresses the second case by making sure that the OF node
reference is not leaked.

The "mdio" node may be NULL, but of_node_put(NULL) is safe.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the "lantiq,xrx200-mdio" child has status = "disabled", the MDIO bus
creation should be avoided. Use of_device_is_available() to check for
that, and take advantage of 2 facts:

- of_device_is_available(NULL) returns false
- of_node_put(NULL) is a no-op
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver does not need any of the functionalities that make
ds->user_mii_bus special. Those use cases are listed here:
https://lore.kernel.org/netdev/20231221174746.hylsmr3f7g5byrsi@skbuf/

It just makes use of ds->user_mii_bus only as storage for its own MDIO
bus, which otherwise has no connection to the framework. This is because:

- the gswip driver only probes on OF: it fails if of_device_get_match_data()
  returns NULL

- when the child OF node of the MDIO bus is absent, no MDIO bus is
  registered at all, not even by the DSA framework. In order for that to
  have happened, the gswip driver would have needed to provide
  ->phy_read() and ->phy_write() in struct dsa_switch_ops, which it does
  not.

We can break the connection between the gswip driver and the DSA
framework and still preserve the same functionality.

Since commit 3b73a7b8 ("net: mdio_bus: add refcounting for fwnodes
to mdiobus"), MDIO buses take ownership of the OF node handled to them,
and release it on their own. The gswip driver no longer needs to do
this.

Combine that with devres, and we no longer need to keep track of
anything for teardown purposes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

__of_mdiobus_register(), called right next, overwrites the phy_mask
we just configured on the bus, so this is redundant and confusing.
Delete it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Inserting the device to block xarray in qdisc_create() is not suitable
place to do this. As it requires use of tcf_block() callback, it causes
multiple issues. It is called for all qdisc types, which is incorrect.

So, instead, move it to more suitable place, which is tcf_block_get_ext()
and make sure it is only done for qdiscs that use block infrastructure
and also only for blocks which are shared.

Symmetrically, alter the cleanup path, move the xarray entry removal
into tcf_block_put_ext().

Fixes: 913b47d3 ("net/sched: Introduce tc block netdev tracking infra")
Reported-by: Ido Schimmel <idosch@nvidia.com>
Closes: https://lore.kernel.org/all/ZY1hBb8GFwycfgvd@shredder/Reported-by: Kui-Feng Lee <sinquersw@gmail.com>
Closes: https://lore.kernel.org/all/ce8d3e55-b8bc-409c-ace9-5cf1c4f7c88e@gmail.com/
Reported-and-tested-by: syzbot+84339b9e7330daae4d66@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/0000000000007c85f5060dcc3a28@google.com/
Reported-and-tested-by: syzbot+806b0572c8d06b66b234@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/00000000000082f2f2060dcc3a92@google.com/
Reported-and-tested-by: syzbot+0039110f932d438130f9@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/0000000000007fbc8c060dcc3a5c@google.com/Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Tested-by: Victor Nogueira <victor@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cross-merge networking fixes after downstream PR.

Conflicts:

drivers/net/ethernet/broadcom/bnxt/bnxt.c
  e009b2ef ("bnxt_en: Remove mis-applied code from bnxt_cfg_ntp_filters()")
  0f2b2147 ("bnxt_en: Fix compile error without CONFIG_RFS_ACCEL")
https://lore.kernel.org/all/20240105115509.225aa8a2@canb.auug.org.au/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'wireless-next-2024-01-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next

Johannes Berg says:

====================
Just a couple of more things over the holidays:

 - first kunit tests for both cfg80211 and mac80211
 - a few multi-link fixes
 - DSCP mapping update
 - RCU fix

* tag 'wireless-next-2024-01-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next:
  wifi: mac80211: remove redundant ML element check
  wifi: cfg80211: parse all ML elements in an ML probe response
  wifi: cfg80211: correct comment about MLD ID
  wifi: cfg80211: Update the default DSCP-to-UP mapping
  wifi: cfg80211: tests: add some scanning related tests
  wifi: mac80211: kunit: extend MFP tests
  wifi: mac80211: kunit: generalize public action test
  wifi: mac80211: add kunit tests for public action handling
  kunit: add a convenience allocation wrapper for SKBs
  kunit: add parameter generation macro using description from array
  wifi: mac80211: fix spelling typo in comment
  wifi: cfg80211: fix RCU dereference in __cfg80211_bss_update
====================

Link: https://lore.kernel.org/r/20240103144423.52269-3-johannes@sipsolutions.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When r8169 is built-in but LED support is a loadable module, the new
code to drive the LED causes a link failure:

ld: drivers/net/ethernet/realtek/r8169_leds.o: in function `rtl8168_init_leds':
r8169_leds.c:(.text+0x36c): undefined reference to `devm_led_classdev_register_ext'

LED support is an optional feature, so fix this issue by adding a Kconfig
symbol R8169_LEDS that is guaranteed to be false if r8169 is built-in
and LED core support is a module. As a positive side effect of this change
r8169_leds.o no longer is built under this configuration.

Fixes: 18764b88 ("r8169: add support for LED's on RTL8168/RTL8101")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312281159.9TPeXbNd-lkp@intel.com/Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Tested-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/d055aeb5-fe5c-4ccf-987f-5af93a17537b@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The driver code proper is handled by the lynx_pcs. The enetc just needs
to populate phylink's supported_interfaces array, and return true for
this phy-mode in enetc_port_has_pcs(), such that it creates an internal
MDIO bus through which the Lynx PCS registers are accessed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20240103113445.3892971-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from wireless and netfilter.

  We haven't accumulated much over the break. If it wasn't for the
  uninterrupted stream of fixes for Intel drivers this PR would be very
  slim. There was a handful of user reports, however, either they stood
  out because of the lower traffic or users have had more time to test
  over the break. The ones which are v6.7-relevant should be wrapped up.

  Current release - regressions:

   - Revert "net: ipv6/addrconf: clamp preferred_lft to the minimum
     required", it caused issues on networks where routers send prefixes
     with preferred_lft=0

   - wifi:
      - iwlwifi: pcie: don't synchronize IRQs from IRQ, prevent deadlock
      - mac80211: fix re-adding debugfs entries during reconfiguration

  Current release - new code bugs:

   - tcp: print AO/MD5 messages only if there are any keys

  Previous releases - regressions:

   - virtio_net: fix missing dma unmap for resize, prevent OOM

  Previous releases - always broken:

   - mptcp: prevent tcp diag from closing listener subflows

   - nf_tables:
      - set transport header offset for egress hook, fix IPv4 mangling
      - skip set commit for deleted/destroyed sets, avoid double deactivation

   - nat: make sure action is set for all ct states, fix openvswitch
     matching on ICMP packets in related state

   - eth: mlxbf_gige: fix receive hang under heavy traffic

   - eth: r8169: fix PCI error on system resume for RTL8168FP

   - net: add missing getsockopt(SO_TIMESTAMPING_NEW) and cmsg handling"

* tag 'net-6.7-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (52 commits)
  net/tcp: Only produce AO/MD5 logs if there are any keys
  net: Implement missing SO_TIMESTAMPING_NEW cmsg support
  bnxt_en: Remove mis-applied code from bnxt_cfg_ntp_filters()
  net: ravb: Wait for operating mode to be applied
  asix: Add check for usbnet_get_endpoints
  octeontx2-af: Re-enable MAC TX in otx2_stop processing
  octeontx2-af: Always configure NIX TX link credits based on max frame size
  net/smc: fix invalid link access in dumping SMC-R connections
  net/qla3xxx: fix potential memleak in ql_alloc_buffer_queues
  virtio_net: fix missing dma unmap for resize
  igc: Fix hicredit calculation
  ice: fix Get link status data length
  i40e: Restore VF MSI-X state during PCI reset
  i40e: fix use-after-free in i40e_aqc_add_filters()
  net: Save and restore msg_namelen in sock_sendmsg
  netfilter: nft_immediate: drop chain reference counter on error
  netfilter: nf_nat: fix action not being set for all ct states
  net: bcmgenet: Fix FCS generation for fragmented skbuffs
  mptcp: prevent tcp diag from closing listener subflows
  MAINTAINERS: add Geliang as reviewer for MPTCP
  ...

This reverts commit 32bb4515.
This reverts commit d078d480.
This reverts commit fcc4b105.
This reverts commit 345237db.
This reverts commit 7db69ec9.
This reverts commit 95132a01.
This reverts commit 63d5eaf3.
This reverts commit c29451ae.
This reverts commit 2ab0edb5.
This reverts commit dedd702a.
This reverts commit 034fcc21.
This reverts commit 9c5625f5.
This reverts commit 02018c54.

Looks like we need more time for reviews, and incremental
changes will be hard to make sense of. So revert.

Link: https://lore.kernel.org/all/ZZP6FV5sXEf+xd58@shell.armlinux.org.uk/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 688eb819 ("x86/csum: Improve performance of `csum_partial`")
ended up improving the code generation for the IP csum calculations, and
in particular special-casing the 40-byte case that is a hot case for
IPv6 headers.

It then had _another_ special case for the 64-byte unrolled loop, which
did two chains of 32-byte blocks, which allows modern CPU's to improve
performance by doing the chains in parallel thanks to renaming the carry
flag.

This just unifies the special cases and combines them into just one
single helper the 40-byte csum case, and replaces the 64-byte case by a
80-byte case that just does that single helper twice.  It avoids having
all these different versions of inline assembly, and actually improved
performance further in my tests.

There was never anything magical about the 64-byte unrolled case, even
though it happens to be a common size (and typically is the cacheline
size).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The special case for odd aligned buffers is unnecessary and mostly
just adds overhead. Aligned buffers is the expectations, and even for
unaligned buffer, the only case that was helped is if the buffer was
1-byte from word aligned which is ~1/7 of the cases. Overall it seems
highly unlikely to be worth to extra branch.

It was left in the previous perf improvement patch because I was
erroneously comparing the exact output of `csum_partial(...)`, but
really we only need `csum_fold(csum_partial(...))` to match so its
safe to remove.

All csum kunit tests pass.
Signed-off-by: Noah Goldstein <goldstein.w.n@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Laight <david.laight@aculab.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'ieee802154-for-net-next-2023-12-20' of gitolite.kernel.org:pub/scm/linux/kernel/git/wpan/wpan-next

Miquel Raynal says:

====================
This pull request mainly brings support for dynamic associations in
the WPAN world. Thanks to the recent improvements it was possible to
discover nearby devices, it is now also possible to associate with them
to form a sub-network using a specific PAN ID. The support includes
several functions, such as:

* Requesting an association to a coordinator, waiting for the response
* Sending a disassociation notification to a coordinator
* Receiving an association request when we are coordinator, answering
  the request (for now all devices are accepted up to a limit, to be
  refined)
* Sending a disassociation notification to a child
* Users may request the list of associated devices (the parent and the
  children).

Here are a few example of userspace calls that can be made:
 # iwpan dev <dev> associate pan_id 2 coord $COORD
 # iwpan dev <dev> list_associations
 # iwpan dev <dev> disassociate ext_addr $COORD

There are as well two patches from Uwe turning remove callbacks into
void functions.

* tag 'ieee802154-for-net-next-2023-12-20' of gitolite.kernel.org:pub/scm/linux/kernel/git/wpan/wpan-next:
  mac802154: Avoid new associations while disassociating
  ieee802154: Avoid confusing changes after associating
  mac802154: Only allow PAN controllers to process association requests
  mac802154: Use the PAN coordinator parameter when stamping packets
  mac80254: Provide real PAN coordinator info in beacons
  ieee802154: Give the user the association list
  mac802154: Handle disassociation notifications from peers
  mac802154: Follow the number of associated devices
  ieee802154: Add support for limiting the number of associated devices
  mac802154: Handle association requests from peers
  mac802154: Handle disassociations
  ieee802154: Add support for user disassociation requests
  mac802154: Handle associating
  ieee802154: Add support for user association requests
  ieee802154: Internal PAN management
  ieee802154: Let PAN IDs be reset
  ieee802154: hwsim: Convert to platform remove callback returning void
  ieee802154: fakelb: Convert to platform remove callback returning void
====================

Link: https://lore.kernel.org/r/20231220095556.4d9cef91@xps-13Signed-off-by: Jakub Kicinski <kuba@kernel.org>

After merging the net-next tree, today's linux-next build (x86_64
allmodconfig) failed like this:

drivers/net/phy/aquantia/aquantia_firmware.c: In function 'aqr_fw_load_memory':
drivers/net/phy/aquantia/aquantia_firmware.c:135:23: error: implicit declaration of function 'crc_ccitt_false'; did you mean 'crc_ccitt_byte'? [-Werror=implicit-function-declaration]
  135 |                 crc = crc_ccitt_false(crc, crc_data, sizeof(crc_data));
      |                       ^~~~~~~~~~~~~~~
      |                       crc_ccitt_byte

Caused by commit e93984eb ("net: phy: aquantia: add firmware load support")
interacting with commit ("lib: crc_ccitt_false() is identical to crc_itu_t()")
from the mm tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20231221130946.7ed9a805@canb.auug.org.auSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit c902ba32.
This reverts commit 50648968.
This reverts commit 77cef1e0.
This reverts commit 8f8d322b.
This reverts commit 6ca7b548.
This reverts commit db468f92.
This reverts commit 5f8c64c2.
This reverts commit ebdc193b.

The driver needs more work.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'platform-drivers-x86-v6.7-7' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86

Pull x86 platform driver fix from Ilpo Järvinen:
 "Unfortunately the P2SB deadlock fix broke some older HW and we need
  some time to figure out the best way to fix the issue so reverting the
  deadlock fix for now"

* tag 'platform-drivers-x86-v6.7-7' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
  Revert "platform/x86: p2sb: Allow p2sb_bar() calls during PCI device probe"

Pull sound fixes from Takashi Iwai:
 "It became more than wished, partly because of vacations. But all
  changes are fairly device-specific and should be safe to apply:

   - A regression fix for Oops at ASoC HD-audio probe

   - A series of TAS2781 HD-audio codec fixes

   - A random build regression fix with SPI helpers

   - Minor endianness fix for USB-audio mixer code

   - ASoC FSL driver error handling fix

   - ASoC Mediatek driver register fix

   - A series of ASoC meson g12a driver fixes

   - A few usual HD-audio oneliner quirks"

* tag 'sound-6.7-final' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek: Fix mute and mic-mute LEDs for HP ProBook 440 G6
  ASoC: meson: g12a-tohdmitx: Fix event generation for S/PDIF mux
  ASoC: meson: g12a-toacodec: Fix event generation
  ASoC: meson: g12a-tohdmitx: Validate written enum values
  ASoC: meson: g12a-toacodec: Validate written enum values
  ASoC: SOF: Intel: hda-codec: Delay the codec device registration
  ALSA: hda: cs35l41: fix building without CONFIG_SPI
  ALSA: hda/realtek: fix mute/micmute LEDs for a HP ZBook
  ALSA: hda/realtek: enable SND_PCI_QUIRK for hp pavilion 14-ec1xxx series
  ASoC: mediatek: mt8186: fix AUD_PAD_TOP register and offset
  ALSA: scarlett2: Convert meter levels from little-endian
  ALSA: hda/tas2781: remove sound controls in unbind
  ALSA: hda/tas2781: move set_drv_data outside tasdevice_init
  ALSA: hda/tas2781: fix typos in comment
  ALSA: hda/tas2781: do not use regcache
  ASoC: fsl_rpmsg: Fix error handler with pm_runtime_enable

Pull drm fixes from Dave Airlie:
 "These were from over the holiday period, mainly i915, a couple of
  qaic, bridge and an mgag200.

  qaic:
   - fix GEM import
   - add quirk for soc version

  bridge:
   - parade-ps8640, ti-sn65dsi86: fix aux reads bounds

  mgag200:
   - fix gamma LUT init

  i915:
   - Fix bogus DPCD rev usage for DP phy test pattern setup
   - Fix handling of MMIO triggered reports in the OA buffer"

* tag 'drm-fixes-2024-01-04' of git://anongit.freedesktop.org/drm/drm:
  drm/i915/perf: Update handling of MMIO triggered reports
  drm/i915/dp: Fix passing the correct DPCD_REV for drm_dp_set_phy_test_pattern
  drm/mgag200: Fix gamma lut not initialized for G200ER, G200EV, G200SE
  drm/bridge: ps8640: Fix size mismatch warning w/ len
  drm/bridge: ti-sn65dsi86: Never store more than msg->size bytes in AUX xfer
  drm/bridge: parade-ps8640: Never store more than msg->size bytes in AUX xfer
  accel/qaic: Implement quirk for SOC_HW_VERSION
  accel/qaic: Fix GEM import path code

User won't care about inproper hash options in the TCP header if they
don't use neither TCP-AO nor TCP-MD5. Yet, those logs can add up in
syslog, while not being a real concern to the host admin:
> kernel: TCP: TCP segment has incorrect auth options set for XX.20.239.12.54681->XX.XX.90.103.80 [S]

Keep silent and avoid logging when there aren't any keys in the system.

Side-note: I also defined static_branch_tcp_*() helpers to avoid more
ifdeffery, going to remove more ifdeffery further with their help.
Reported-by: Christian Kujau <lists@nerdbynature.de>
Closes: https://lore.kernel.org/all/f6b59324-1417-566f-a976-ff2402718a8d@nerdbynature.de/Signed-off-by: Dmitry Safonov <dima@arista.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Fixes: 2717b5ad ("net/tcp: Add tcp_hash_fail() ratelimited logs")
Link: https://lore.kernel.org/r/20240104-tcp_hash_fail-logs-v1-1-ff3e1f6f9e72@arista.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2024-01-03 (i40e, ice, igc)

This series contains updates to i40e, ice, and igc drivers.

Ke Xiao fixes use after free for unicast filters on i40e.

Andrii restores VF MSI-X flag after PCI reset on i40e.

Paul corrects admin queue link status structure to fulfill firmware
expectations for ice.

Rodrigo Cataldo corrects value used for hicredit calculations on igc.

* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  igc: Fix hicredit calculation
  ice: fix Get link status data length
  i40e: Restore VF MSI-X state during PCI reset
  i40e: fix use-after-free in i40e_aqc_add_filters()
====================

Link: https://lore.kernel.org/r/20240103193254.822968-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 9718475e ("socket: Add SO_TIMESTAMPING_NEW") added the new
socket option SO_TIMESTAMPING_NEW. However, it was never implemented in
__sock_cmsg_send thus breaking SO_TIMESTAMPING cmsg for platforms using
SO_TIMESTAMPING_NEW.

Fixes: 9718475e ("socket: Add SO_TIMESTAMPING_NEW")
Link: https://lore.kernel.org/netdev/6a7281bf-bc4a-4f75-bb88-7011908ae471@app.fastmail.com/Signed-off-by: Thomas Lange <thomas@corelatus.se>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20240104085744.49164-1-thomas@corelatus.seSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit b28ff7a7.

The commit introduced P2SB device scan and resource cache during the
boot process to avoid deadlock. But it caused detection failure of
IDE controllers on old systems [1]. The IDE controllers on old systems
and P2SB devices on newer systems have same PCI DEVFN. It is suspected
the confusion between those two is the failure cause. Revert the change
at this moment until the proper solution gets ready.

Link: https://lore.kernel.org/platform-driver-x86/CABq1_vjfyp_B-f4LAL6pg394bP6nDFyvg110TOLHHb0x4aCPeg@mail.gmail.com/T/#m07b30468d9676fc5e3bb2122371121e4559bb383 [1]
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20240104114050.3142690-1-shinichiro.kawasaki@wdc.comReviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>

Move phylink_pcs_neg_mode() from the header file into the .c file since
nothing should be using it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Luiz Angelo Daros de Luca reports that the MDIO bus code maintains a
reference to the DT node, but does not hold a refcount on the node.

The simple solution to this is to add the necessary refcounting into
the MDIO bus code for all users, ensuring that on registration, the
refcount is incremented, and only dropped when the MDIO bus is
released.

Do this for fwnodes, so we not only fix this for DT, but also other
types of firmware nodes as well.
Reported-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following compile error:

.../bnxt.c: In function 'bnxt_cfg_ntp_filters':
.../bnxt.c:14077:37: error: implicit declaration of function 'rps_may_expire_flow' [-Werror=implicit-function-declaration]
14077 |                                 if (rps_may_expire_flow(bp->dev, fltr->base.rxq,
      |                                     ^~~~~~~~~~~~~~~~~~~

bnxt_cfg_ntp_filters() is only used when CONFIG_RFS_ACCEL is enabled.
User configured ntuple filters are directly added and will not go through
this function.  Wrap the body of bnxt_cfg_ntp_filters() with
CONFIG_RFS_ACCEL.

Fixes: 59cde76f ("bnxt_en: Refactor filter insertion logic in bnxt_rx_flow_steer().")
Reported-by: Arnd Bergmann <arnd@kernel.org>
Link: https://lore.kernel.org/netdev/20240103102332.3642417-1-arnd@kernel.org/Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 2 lines to check for the BNXT_HWRM_PF_UNLOAD_SP_EVENT bit was
mis-applied to bnxt_cfg_ntp_filters() and should have been applied to
bnxt_sp_task().

Fixes: 19241368 ("bnxt_en: Send PF driver unload notification to all VFs.")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CSR.OPS bits specify the current operating mode and (according to
documentation) they are updated by HW when the operating mode change
request is processed. To comply with this check CSR.OPS before proceeding.

Commit introduces ravb_set_opmode() that does all the necessities for
setting the operating mode (set CCC.OPC (and CCC.GAC, CCC.CSEL, if any) and
wait for CSR.OPS) and call it where needed. This should comply with all the
HW manuals requirements as different manual variants specify that different
modes need to be checked in CSR.OPS when setting CCC.OPC.

If gPTP active in config mode is supported and it needs to be enabled, the
CCC.GAC and CCC.CSEL needs to be configured along with CCC.OPC in the same
write access. For this, ravb_set_opmode() allows passing GAC and CSEL as
part of opmode and the function updates accordingly CCC register.

Fixes: c156633f ("Renesas Ethernet AVB driver proper")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>