- 31 May, 2019 40 commits
-
-
Nicholas Kazlauskas authored
[ Upstream commit 6752bea8 ] [Why] The actual position for the cursor on the screen is essentially: x_out = x - x_plane - x_hotspot y_out = y - y_plane - y_hotspot The register values for cursor position and cursor hotspot need to be greater than zero when programmed, but we also need to subtract off the plane position to display the cursor at the correct position. Since we don't want x or y to be less than zero, we add the plane position as a positive value to x_hotspot or y_hotspot. However, what this doesn't take into account is that the hotspot registers are limited by the maximum cursor size. On DCN10 the cursor hotspot regitsers are masked to 0xFF, so they have a maximum value of 0-255. Values greater this will wrap, causing the cursor to display in the wrong position. In practice this means that for sufficiently large plane positions, the cursor will be drawn twice on the screen, and can cause screen flashes or p-state WARNS depending on what the wrapped value is. So we need a way to remove the value from x_plane and y_plane without exceeding the maximum cursor size. [How] Subtract as much as x_plane/y_plane as possible from x and y and place the remainder in the cursor hotspot register. The value for x_hotspot and y_hotspot can still wrap around but it won't happen in a case where the cursor is actually enabled. The cursor plane needs to intersect at least one pixel of the plane's rectangle to be enabled, so the cursor position + hotspot provided by userspace must always be strictly less than the maximum cursor size for the cursor to actually be enabled. Signed-off-by:
Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by:
Sun peng Li <Sunpeng.Li@amd.com> Acked-by:
Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Yannick Fertré authored
[ Upstream commit 0084c3c7 ] At the end of initialization, a delay is required by the panel. Without this delay, the panel could received a frame early & generate a crash of panel (black screen). Signed-off-by:
Yannick Fertré <yannick.fertre@st.com> Reviewed-by:
Philippe Cornu <philippe.cornu@st.com> Tested-by:
Thierry Reding <treding@nvidia.com> Link: https://patchwork.freedesktop.org/patch/msgid/1553155445-13407-1-git-send-email-yannick.fertre@st.comSigned-off-by:
-
Stanley Chu authored
[ Upstream commit 3b141e8c ] For regulators used by UFS, vcc, vccq and vccq2 will have voltage range initialized by ufshcd_populate_vreg(), however other regulators may have undefined voltage range if dt-bindings have no such definition. In above undefined case, both "min_uV" and "max_uV" fields in ufs_vreg struct will be zero values and these values will be configured on regulators in different power modes. Currently this may have no harm if both "min_uV" and "max_uV" always keep "zero values" because regulator_set_voltage() will always bypass such invalid values and return "good" results. However improper values shall be fixed to avoid potential bugs. Simply bypass voltage configuration if voltage range is not defined. Signed-off-by:
Stanley Chu <stanley.chu@mediatek.com> Reviewed-by:
Avri Altman <avri.altman@wdc.com> Acked-by:
Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Stanley Chu authored
[ Upstream commit 0487fff7 ] Currently if a regulator has "<name>-fixed-regulator" property in device tree, it will skip current limit initialization. This lead to a zero "max_uA" value in struct ufs_vreg. However, "regulator_set_load" operation shall be required on regulators which have valid current limits, otherwise a zero "max_uA" set by "regulator_set_load" may cause unexpected behavior when this regulator is enabled or set as high power mode. Similarly, in device's icc_level configuration flow, the target icc_level shall be updated if regulator also has valid current limit, otherwise a wrong icc_level will be calculated by zero "max_uA" and thus causes unexpected results after it is written to device. Signed-off-by:
-
Ping-Ke Shih authored
[ Upstream commit 60209d48 ] In case dev_alloc_skb fails, the fix safely returns to avoid potential NULL pointer dereference. Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Geert Uytterhoeven authored
[ Upstream commit 1723fdec ] While devm_gpiod_get_index_optional() returns NULL if the GPIO is not present (i.e. -ENOENT), it may still return other error codes, like -EPROBE_DEFER. Currently these are not handled, leading to unrecoverable failures later in case of probe deferral: gpiod_set_consumer_name: invalid GPIO (errorpointer) gpiod_direction_output: invalid GPIO (errorpointer) gpiod_set_value_cansleep: invalid GPIO (errorpointer) gpiod_set_value_cansleep: invalid GPIO (errorpointer) gpiod_set_value_cansleep: invalid GPIO (errorpointer) Detect and propagate errors to fix this. Fixes: f3186dd8 ("spi: Optionally use GPIO descriptors for CS GPIOs") Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Alexandre Belloni authored
[ Upstream commit a652e00e ] The IRQ is requested before the struct rtc is allocated and registered, but this struct is used in the IRQ handler. This may lead to a NULL pointer dereference. Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc struct before requesting the IRQ. Signed-off-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by:
-
Piotr Figiel authored
[ Upstream commit 24d413a3 ] Fix a race which leads to an Oops with NULL pointer dereference. The dereference is in brcmf_config_dongle() when cfg_to_ndev() attempts to get net_device structure of interface with index 0 via if2bss mapping. This shouldn't fail because of check for bus being ready in brcmf_netdev_open(), but it's not synchronised with USB disconnect and there is a race: after the check the bus can be marked down and the mapping for interface 0 may be gone. Solve this by modifying disconnect handling so that the removal of mapping of ifidx to brcmf_if structure happens after netdev removal (which is synchronous with brcmf_netdev_open() thanks to rtln being locked in devinet_ioctl()). This assures brcmf_netdev_open() returns before the mapping is removed during disconnect. Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = bcae2612 [00000008] *pgd=8be73831 Internal error: Oops: 17 [#1] PREEMPT SMP ARM Modules linked in: brcmfmac brcmutil nf_log_ipv4 nf_log_common xt_LOG xt_limit iptable_mangle xt_connmark xt_tcpudp xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_filter ip_tables x_tables usb_f_mass_storage usb_f_rndis u_ether usb_serial_simple usbserial cdc_acm smsc95xx usbnet ci_hdrc_imx ci_hdrc usbmisc_imx ulpi 8250_exar 8250_pci 8250 8250_base libcomposite configfs udc_core [last unloaded: brcmutil] CPU: 2 PID: 24478 Comm: ifconfig Not tainted 4.19.23-00078-ga62866d-dirty #115 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) PC is at brcmf_cfg80211_up+0x94/0x29c [brcmfmac] LR is at brcmf_cfg80211_up+0x8c/0x29c [brcmfmac] pc : [<7f26a91c>] lr : [<7f26a914>] psr: a0070013 sp : eca99d28 ip : 00000000 fp : ee9c6c00 r10: 00000036 r9 : 00000000 r8 : ece4002c r7 : edb5b800 r6 : 00000000 r5 : 80f08448 r4 : edb5b968 r3 : ffffffff r2 : 00000000 r1 : 00000002 r0 : 00000000 Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c5387d Table: 7ca0c04a DAC: 00000051 Process ifconfig (pid: 24478, stack limit = 0xd9e85a0e) Stack: (0xeca99d28 to 0xeca9a000) 9d20: 00000000 80f873b0 0000000d 80f08448 eca99d68 50d45f32 9d40: 7f27de94 ece40000 80f08448 80f08448 7f27de94 ece4002c 00000000 00000036 9d60: ee9c6c00 7f27262c 00001002 50d45f32 ece40000 00000000 80f08448 80772008 9d80: 00000001 00001043 00001002 ece40000 00000000 50d45f32 ece40000 00000001 9da0: 80f08448 00001043 00001002 807723d0 00000000 50d45f32 80f08448 eca99e58 9dc0: 80f87113 50d45f32 80f08448 ece40000 ece40138 00001002 80f08448 00000000 9de0: 00000000 80772434 edbd5380 eca99e58 edbd5380 80f08448 ee9c6c0c 80805f70 9e00: 00000000 ede08e00 00008914 ece40000 00000014 ee9c6c0c 600c0013 00001043 9e20: 0208a8c0 ffffffff 00000000 50d45f32 eca98000 80f08448 7ee9fc38 00008914 9e40: 80f68e40 00000051 eca98000 00000036 00000003 80808b9c 6e616c77 00000030 9e60: 00000000 00000000 00001043 0208a8c0 ffffffff 00000000 80f08448 00000000 9e80: 00000000 816d8b20 600c0013 00000001 ede09320 801763d4 00000000 50d45f32 9ea0: eca98000 80f08448 7ee9fc38 50d45f32 00008914 80f08448 7ee9fc38 80f68e40 9ec0: ed531540 8074721c 00000800 00000001 00000000 6e616c77 00000030 00000000 9ee0: 00000000 00001002 0208a8c0 ffffffff 00000000 50d45f32 80f08448 7ee9fc38 9f00: ed531560 ec8fc900 80285a6c 80285138 edb910c0 00000000 ecd91008 ede08e00 9f20: 80f08448 00000000 00000000 816d8b20 600c0013 00000001 ede09320 801763d4 9f40: 00000000 50d45f32 00021000 edb91118 edb910c0 80f08448 01b29000 edb91118 9f60: eca99f7c 50d45f32 00021000 ec8fc900 00000003 ec8fc900 00008914 7ee9fc38 9f80: eca98000 00000036 00000003 80285a6c 00086364 7ee9fe1c 000000c3 00000036 9fa0: 801011c4 80101000 00086364 7ee9fe1c 00000003 00008914 7ee9fc38 00086364 9fc0: 00086364 7ee9fe1c 000000c3 00000036 0008630c 7ee9fe1c 7ee9fc38 00000003 9fe0: 000a42b8 7ee9fbd4 00019914 76e09acc 600c0010 00000003 00000000 00000000 [<7f26a91c>] (brcmf_cfg80211_up [brcmfmac]) from [<7f27262c>] (brcmf_netdev_open+0x74/0xe8 [brcmfmac]) [<7f27262c>] (brcmf_netdev_open [brcmfmac]) from [<80772008>] (__dev_open+0xcc/0x150) [<80772008>] (__dev_open) from [<807723d0>] (__dev_change_flags+0x168/0x1b4) [<807723d0>] (__dev_change_flags) from [<80772434>] (dev_change_flags+0x18/0x48) [<80772434>] (dev_change_flags) from [<80805f70>] (devinet_ioctl+0x67c/0x79c) [<80805f70>] (devinet_ioctl) from [<80808b9c>] (inet_ioctl+0x210/0x3d4) [<80808b9c>] (inet_ioctl) from [<8074721c>] (sock_ioctl+0x350/0x524) [<8074721c>] (sock_ioctl) from [<80285138>] (do_vfs_ioctl+0xb0/0x9b0) [<80285138>] (do_vfs_ioctl) from [<80285a6c>] (ksys_ioctl+0x34/0x5c) [<80285a6c>] (ksys_ioctl) from [<80101000>] (ret_fast_syscall+0x0/0x28) Exception stack(0xeca99fa8 to 0xeca99ff0) 9fa0: 00086364 7ee9fe1c 00000003 00008914 7ee9fc38 00086364 9fc0: 00086364 7ee9fe1c 000000c3 00000036 0008630c 7ee9fe1c 7ee9fc38 00000003 9fe0: 000a42b8 7ee9fbd4 00019914 76e09acc Code: e5970328 eb002021 e1a02006 e3a01002 (e5909008) ---[ end trace 5cbac2333f3ac5df ]--- Signed-off-by:
Piotr Figiel <p.figiel@camlintechnologies.com> Signed-off-by:
-
Piotr Figiel authored
[ Upstream commit db3b9e2e ] It was observed that rarely during USB disconnect happening shortly after connect (before full initialization completes) usb_hub_wq would wait forever for the dev_init_lock to be unlocked. dev_init_lock would remain locked though because of infinite wait during usb_kill_urb: [ 2730.656472] kworker/0:2 D 0 260 2 0x00000000 [ 2730.660700] Workqueue: events request_firmware_work_func [ 2730.664807] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac) [ 2730.670587] [<809dd164>] (schedule) from [<8069af44>] (usb_kill_urb+0xdc/0x114) [ 2730.676815] [<8069af44>] (usb_kill_urb) from [<7f258b50>] (brcmf_usb_free_q+0x34/0xa8 [brcmfmac]) [ 2730.684833] [<7f258b50>] (brcmf_usb_free_q [brcmfmac]) from [<7f2517d4>] (brcmf_detach+0xa0/0xb8 [brcmfmac]) [ 2730.693557] [<7f2517d4>] (brcmf_detach [brcmfmac]) from [<7f251a34>] (brcmf_attach+0xac/0x3d8 [brcmfmac]) [ 2730.702094] [<7f251a34>] (brcmf_attach [brcmfmac]) from [<7f2587ac>] (brcmf_usb_probe_phase2+0x468/0x4a0 [brcmfmac]) [ 2730.711601] [<7f2587ac>] (brcmf_usb_probe_phase2 [brcmfmac]) from [<7f252888>] (brcmf_fw_request_done+0x194/0x220 [brcmfmac]) [ 2730.721795] [<7f252888>] (brcmf_fw_request_done [brcmfmac]) from [<805748e4>] (request_firmware_work_func+0x4c/0x88) [ 2730.731125] [<805748e4>] (request_firmware_work_func) from [<80141474>] (process_one_work+0x228/0x808) [ 2730.739223] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564) [ 2730.746105] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c) [ 2730.752227] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20) [ 2733.099695] kworker/0:3 D 0 1065 2 0x00000000 [ 2733.103926] Workqueue: usb_hub_wq hub_event [ 2733.106914] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac) [ 2733.112693] [<809dd164>] (schedule) from [<809e2a8c>] (schedule_timeout+0x214/0x3e4) [ 2733.119621] [<809e2a8c>] (schedule_timeout) from [<809dde2c>] (wait_for_common+0xc4/0x1c0) [ 2733.126810] [<809dde2c>] (wait_for_common) from [<7f258d00>] (brcmf_usb_disconnect+0x1c/0x4c [brcmfmac]) [ 2733.135206] [<7f258d00>] (brcmf_usb_disconnect [brcmfmac]) from [<8069e0c8>] (usb_unbind_interface+0x5c/0x1e4) [ 2733.143943] [<8069e0c8>] (usb_unbind_interface) from [<8056d3e8>] (device_release_driver_internal+0x164/0x1fc) [ 2733.152769] [<8056d3e8>] (device_release_driver_internal) from [<8056c078>] (bus_remove_device+0xd0/0xfc) [ 2733.161138] [<8056c078>] (bus_remove_device) from [<8056977c>] (device_del+0x11c/0x310) [ 2733.167939] [<8056977c>] (device_del) from [<8069cba8>] (usb_disable_device+0xa0/0x1cc) [ 2733.174743] [<8069cba8>] (usb_disable_device) from [<8069507c>] (usb_disconnect+0x74/0x1dc) [ 2733.181823] [<8069507c>] (usb_disconnect) from [<80695e88>] (hub_event+0x478/0xf88) [ 2733.188278] [<80695e88>] (hub_event) from [<80141474>] (process_one_work+0x228/0x808) [ 2733.194905] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564) [ 2733.201724] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c) [ 2733.207913] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20) It was traced down to a case where usb_kill_urb would be called on an URB structure containing more or less random data, including large number in its use_count. During the debugging it appeared that in brcmf_usb_free_q() the traversal over URBs' lists is not synchronized with operations on those lists in brcmf_usb_rx_complete() leading to handling brcmf_usbdev_info structure (holding lists' head) as lists' element and in result causing above problem. Fix it by walking through all URBs during brcmf_cancel_all_urbs using the arrays of requests instead of linked lists. Signed-off-by:
-
Piotr Figiel authored
[ Upstream commit c80d26e8 ] brcmu_pkt_buf_free_skb emits WARNING when attempting to free a sk_buff which is part of any queue. After USB disconnect this may have happened when brcmf_fws_hanger_cleanup() is called as per-interface psq was never cleaned when removing the interface. Change brcmf_fws_macdesc_cleanup() in a way that it removes the corresponding packets from hanger table (to avoid double-free when brcmf_fws_hanger_cleanup() is called) and add a call to clean-up the interface specific packet queue. Below is a WARNING during USB disconnect with Raspberry Pi WiFi dongle running in AP mode. This was reproducible when the interface was transmitting during the disconnect and is fixed with this commit. ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1171 at drivers/net/wireless/broadcom/brcm80211/brcmutil/utils.c:49 brcmu_pkt_buf_free_skb+0x3c/0x40 Modules linked in: nf_log_ipv4 nf_log_common xt_LOG xt_limit iptable_mangle xt_connmark xt_tcpudp xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_filter ip_tables x_tables usb_f_mass_storage usb_f_rndis u_ether cdc_acm smsc95xx usbnet ci_hdrc_imx ci_hdrc ulpi usbmisc_imx 8250_exar 8250_pci 8250 8250_base libcomposite configfs udc_core CPU: 0 PID: 1171 Comm: kworker/0:0 Not tainted 4.19.23-00075-gde33ed8 #99 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Workqueue: usb_hub_wq hub_event [<8010ff84>] (unwind_backtrace) from [<8010bb64>] (show_stack+0x10/0x14) [<8010bb64>] (show_stack) from [<80840278>] (dump_stack+0x88/0x9c) [<80840278>] (dump_stack) from [<8011f5ec>] (__warn+0xfc/0x114) [<8011f5ec>] (__warn) from [<8011f71c>] (warn_slowpath_null+0x40/0x48) [<8011f71c>] (warn_slowpath_null) from [<805a476c>] (brcmu_pkt_buf_free_skb+0x3c/0x40) [<805a476c>] (brcmu_pkt_buf_free_skb) from [<805bb6c4>] (brcmf_fws_cleanup+0x1e4/0x22c) [<805bb6c4>] (brcmf_fws_cleanup) from [<805bc854>] (brcmf_fws_del_interface+0x58/0x68) [<805bc854>] (brcmf_fws_del_interface) from [<805b66ac>] (brcmf_remove_interface+0x40/0x150) [<805b66ac>] (brcmf_remove_interface) from [<805b6870>] (brcmf_detach+0x6c/0xb0) [<805b6870>] (brcmf_detach) from [<805bdbb8>] (brcmf_usb_disconnect+0x30/0x4c) [<805bdbb8>] (brcmf_usb_disconnect) from [<805e5d64>] (usb_unbind_interface+0x5c/0x1e0) [<805e5d64>] (usb_unbind_interface) from [<804aab10>] (device_release_driver_internal+0x154/0x1ec) [<804aab10>] (device_release_driver_internal) from [<804a97f4>] (bus_remove_device+0xcc/0xf8) [<804a97f4>] (bus_remove_device) from [<804a6fc0>] (device_del+0x118/0x308) [<804a6fc0>] (device_del) from [<805e488c>] (usb_disable_device+0xa0/0x1c8) [<805e488c>] (usb_disable_device) from [<805dcf98>] (usb_disconnect+0x70/0x1d8) [<805dcf98>] (usb_disconnect) from [<805ddd84>] (hub_event+0x464/0xf50) [<805ddd84>] (hub_event) from [<80135a70>] (process_one_work+0x138/0x3f8) [<80135a70>] (process_one_work) from [<80135d5c>] (worker_thread+0x2c/0x554) [<80135d5c>] (worker_thread) from [<8013b1a0>] (kthread+0x124/0x154) [<8013b1a0>] (kthread) from [<801010e8>] (ret_from_fork+0x14/0x2c) Exception stack(0xecf8dfb0 to 0xecf8dff8) dfa0: 00000000 00000000 00000000 00000000 dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 ---[ end trace 38d234018e9e2a90 ]--- ------------[ cut here ]------------ Signed-off-by:
-
Piotr Figiel authored
[ Upstream commit a9fd0953 ] Leaving dev_init_lock mutex locked in probe causes BUG and a WARNING when kernel is compiled with CONFIG_PROVE_LOCKING. Convert mutex to completion which silences those warnings and improves code readability. Fix below errors when connecting the USB WiFi dongle: brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43143 for chip BCM43143/2 BUG: workqueue leaked lock or atomic: kworker/0:2/0x00000000/434 last function: hub_event 1 lock held by kworker/0:2/434: #0: 18d5dcdf (&devinfo->dev_init_lock){+.+.}, at: brcmf_usb_probe+0x78/0x550 [brcmfmac] CPU: 0 PID: 434 Comm: kworker/0:2 Not tainted 4.19.23-00084-g454a789-dirty #123 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Workqueue: usb_hub_wq hub_event [<8011237c>] (unwind_backtrace) from [<8010d74c>] (show_stack+0x10/0x14) [<8010d74c>] (show_stack) from [<809c4324>] (dump_stack+0xa8/0xd4) [<809c4324>] (dump_stack) from [<8014195c>] (process_one_work+0x710/0x808) [<8014195c>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564) [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c) [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20) Exception stack(0xed1d9fb0 to 0xed1d9ff8) 9fa0: 00000000 00000000 00000000 00000000 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ====================================================== WARNING: possible circular locking dependency detected 4.19.23-00084-g454a789-dirty #123 Not tainted ------------------------------------------------------ kworker/0:2/434 is trying to acquire lock: e29cf799 ((wq_completion)"events"){+.+.}, at: process_one_work+0x174/0x808 but task is already holding lock: 18d5dcdf (&devinfo->dev_init_lock){+.+.}, at: brcmf_usb_probe+0x78/0x550 [brcmfmac] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (&devinfo->dev_init_lock){+.+.}: mutex_lock_nested+0x1c/0x24 brcmf_usb_probe+0x78/0x550 [brcmfmac] usb_probe_interface+0xc0/0x1bc really_probe+0x228/0x2c0 __driver_attach+0xe4/0xe8 bus_for_each_dev+0x68/0xb4 bus_add_driver+0x19c/0x214 driver_register+0x78/0x110 usb_register_driver+0x84/0x148 process_one_work+0x228/0x808 worker_thread+0x2c/0x564 kthread+0x13c/0x16c ret_from_fork+0x14/0x20 (null) -> #1 (brcmf_driver_work){+.+.}: worker_thread+0x2c/0x564 kthread+0x13c/0x16c ret_from_fork+0x14/0x20 (null) -> #0 ((wq_completion)"events"){+.+.}: process_one_work+0x1b8/0x808 worker_thread+0x2c/0x564 kthread+0x13c/0x16c ret_from_fork+0x14/0x20 (null) other info that might help us debug this: Chain exists of: (wq_completion)"events" --> brcmf_driver_work --> &devinfo->dev_init_lock Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&devinfo->dev_init_lock); lock(brcmf_driver_work); lock(&devinfo->dev_init_lock); lock((wq_completion)"events"); *** DEADLOCK *** 1 lock held by kworker/0:2/434: #0: 18d5dcdf (&devinfo->dev_init_lock){+.+.}, at: brcmf_usb_probe+0x78/0x550 [brcmfmac] stack backtrace: CPU: 0 PID: 434 Comm: kworker/0:2 Not tainted 4.19.23-00084-g454a789-dirty #123 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Workqueue: events request_firmware_work_func [<8011237c>] (unwind_backtrace) from [<8010d74c>] (show_stack+0x10/0x14) [<8010d74c>] (show_stack) from [<809c4324>] (dump_stack+0xa8/0xd4) [<809c4324>] (dump_stack) from [<80172838>] (print_circular_bug+0x210/0x330) [<80172838>] (print_circular_bug) from [<80175940>] (__lock_acquire+0x160c/0x1a30) [<80175940>] (__lock_acquire) from [<8017671c>] (lock_acquire+0xe0/0x268) [<8017671c>] (lock_acquire) from [<80141404>] (process_one_work+0x1b8/0x808) [<80141404>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564) [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c) [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20) Exception stack(0xed1d9fb0 to 0xed1d9ff8) 9fa0: 00000000 00000000 00000000 00000000 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit d825db34 ] Clang warns about what is clearly a case of passing an uninitalized variable into a static function: drivers/net/wireless/broadcom/b43/phy_lp.c:1852:23: error: variable 'gains' is uninitialized when used here [-Werror,-Wuninitialized] lpphy_papd_cal(dev, gains, 0, 1, 30); ^~~~~ drivers/net/wireless/broadcom/b43/phy_lp.c:1838:2: note: variable 'gains' is declared here struct lpphy_tx_gains gains, oldgains; ^ 1 error generated. However, this function is empty, and its arguments are never evaluated, so gcc in contrast does not warn here. Both compilers behave in a reasonable way as far as I can tell, so we should change the code to avoid the warning everywhere. We could just eliminate the lpphy_papd_cal() function entirely, given that it has had the TODO comment in it for 10 years now and is rather unlikely to ever get done. I'm doing a simpler change here, and just pass the 'oldgains' variable in that has been initialized, based on the guess that this is what was originally meant. Fixes: 2c0d6100 ("b43: LP-PHY: Begin implementing calibration & software RFKILL support") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Reviewed-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit 46953f97 ] In case kmemdup fails, the fix sets conn_info->req_ie_len and conn_info->resp_ie_len to zero to avoid buffer overflows. Signed-off-by:
Kangjie Lu <kjlu@umn.edu> Acked-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
-
YueHaibing authored
[ Upstream commit 003b686a ] 'hostcmd' is alloced by kzalloc, should be freed before leaving from the error handling cases, otherwise it will cause mem leak. Fixes: 3935ccc1 ("mwifiex: add cfg80211 testmode support") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit 76597628 ] In case alloc_workqueue fails, the fix reports the error and returns to avoid NULL pointer dereference. Signed-off-by:
-
Daniel T. Lee authored
[ Upstream commit 0979ff79 ] Currently, ksym_search located at trace_helpers won't check symbols are existing or not. In ksym_search, when symbol is not found, it will return &syms[0](_stext). But when the kernel symbols are not loaded, it will return NULL, which is not a desired action. This commit will add verification logic whether symbols are loaded prior to the symbol search. Signed-off-by:
Daniel T. Lee <danieltimlee@gmail.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Jian Shen authored
[ Upstream commit 389775a6 ] It used netdev->uc and netdev->mc list in function hns3_recover_hw_addr() and hns3_remove_hw_addr(). We should add protect for them. Fixes: f05e2109 ("net: hns3: Clear mac vlan table entries when unload driver or function reset") Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Huazhong Tan authored
[ Upstream commit c4e401e5 ] hns3_get_stats() should check the resetting status firstly, since the device will be reinitialized when resetting. If the reset has not completed, the hns3_get_stats() may access invalid memory. Signed-off-by:
-
Justin Chen authored
[ Upstream commit abbde279 ] Indio->mlock is used for protecting the different iio device modes. It is currently not being used in this way. Replace the lock with an internal lock specifically used for protecting the SPI transfer buffer. Signed-off-by:
Justin Chen <justinpopo6@gmail.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit 6f9ca1d3 ] When building with -Wsometimes-uninitialized, Clang warns: drivers/iio/common/ssp_sensors/ssp_iio.c:95:6: warning: variable 'calculated_time' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized] While it isn't wrong, this will never be a problem because iio_push_to_buffers_with_timestamp only uses calculated_time on the same condition that it is assigned (when scan_timestamp is not zero). While iio_push_to_buffers_with_timestamp is marked as inline, Clang does inlining in the optimization stage, which happens after the semantic analysis phase (plus inline is merely a hint to the compiler). Fix this by just zero initializing calculated_time. Link: https://github.com/ClangBuiltLinux/linux/issues/394Signed-off-by:
Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit 536cc27d ] devm_regmap_init_i2c may fail and return NULL. The fix returns the error when it fails. Signed-off-by:
-
Lars-Peter Clausen authored
[ Upstream commit df1d80ae ] For devices from the SigmaDelta family we need to keep CS low when doing a conversion, since the device will use the MISO line as a interrupt to indicate that the conversion is complete. This is why the driver locks the SPI bus and when the SPI bus is locked keeps as long as a conversion is going on. The current implementation gets one small detail wrong though. CS is only de-asserted after the SPI bus is unlocked. This means it is possible for a different SPI device on the same bus to send a message which would be wrongfully be addressed to the SigmaDelta device as well. Make sure that the last SPI transfer that is done while holding the SPI bus lock de-asserts the CS signal. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Alexandru Ardelean <Alexandru.Ardelean@analog.com> Signed-off-by:
-
Wen Yang authored
[ Upstream commit bc29d3a6 ] The call to of_find_matching_node_and_match returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: drivers/gpu/drm/pl111/pl111_versatile.c:333:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function. drivers/gpu/drm/pl111/pl111_versatile.c:340:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function. drivers/gpu/drm/pl111/pl111_versatile.c:346:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function. drivers/gpu/drm/pl111/pl111_versatile.c:354:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function. drivers/gpu/drm/pl111/pl111_versatile.c:395:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function. drivers/gpu/drm/pl111/pl111_versatile.c:402:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 317, but without a corresponding object release within this function. Signed-off-by:
Wen Yang <wen.yang99@zte.com.cn> Cc: Eric Anholt <eric@anholt.net> (supporter:DRM DRIVER FOR ARM PL111 CLCD) Cc: David Airlie <airlied@linux.ie> (maintainer:DRM DRIVERS) Cc: Daniel Vetter <daniel@ffwll.ch> (maintainer:DRM DRIVERS) Cc: dri-devel@lists.freedesktop.org (open list:DRM DRIVERS) Cc: linux-kernel@vger.kernel.org (open list) Signed-off-by:
Eric Anholt <eric@anholt.net> Link: https://patchwork.freedesktop.org/patch/msgid/1554307455-40361-6-git-send-email-wen.yang99@zte.com.cnSigned-off-by:
-
Ranjani Sridharan authored
[ Upstream commit f96fb7d1 ] When the card is registered by the machine driver, dai link components are probed after the snd_card is created. This is done in snd_soc_bind_card() which calls snd_soc_instantiate_card() to first create the snd_card and then probes the link components by calling soc_probe_link_components(). The snd_card is used by the component driver to add the kcontrols associated with dapm widgets to the card. When the machine driver is unregistered, the snd_card is freed when the card resources are cleaned up. But the snd_card needs to be valid while unloading the topology dapm widgets in order to remove the kcontrols from the card. Since, unloading topology is done when the component driver is removed, the link components should be removed in snd_soc_unbind_card(). This will ensure that the kcontrols are removed before the card resources are cleaned up and the snd_card itself is freed. Signed-off-by:
Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by:
-
Charles Keepax authored
[ Upstream commit 06377301 ] Lockdep reports the following issue on my setup: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock((work_completion)(&(&rdev->disable_work)->work)); lock(regulator_list_mutex); lock((work_completion)(&(&rdev->disable_work)->work)); lock(regulator_list_mutex); The problem is that regulator_unregister takes the regulator_list_mutex and then calls flush_work on disable_work. But regulator_disable_work calls regulator_lock_dependent which will also take the regulator_list_mutex. Resulting in a deadlock if the flush_work call actually needs to flush the work. Fix this issue by moving the flush_work outside of the regulator_list_mutex. The list mutex is not used to guard the point at which the delayed work is queued, so its use adds no additional safety. Fixes: f8702f9e ("regulator: core: Use ww_mutex for regulators locking") Signed-off-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Reviewed-by:
Dmitry Osipenko <digetx@gmail.com> Signed-off-by:
-
Andrey Smirnov authored
[ Upstream commit 0a919ae4 ] Move code calling spi_get_gpio_descs() to happen after ctlr->dev's name is set in order to have proper GPIO consumer names. Before: cat /sys/kernel/debug/gpio gpiochip0: GPIOs 0-31, parent: platform/40049000.gpio, vf610-gpio: gpio-6 ( |regulator-usb0-vbus ) out lo gpiochip1: GPIOs 32-63, parent: platform/4004a000.gpio, vf610-gpio: gpio-36 ( |scl ) in hi gpio-37 ( |sda ) in hi gpio-40 ( |(null) CS1 ) out lo gpio-41 ( |(null) CS0 ) out lo ACTIVE LOW gpio-42 ( |miso ) in hi gpio-43 ( |mosi ) in lo gpio-44 ( |sck ) out lo After: cat /sys/kernel/debug/gpio gpiochip0: GPIOs 0-31, parent: platform/40049000.gpio, vf610-gpio: gpio-6 ( |regulator-usb0-vbus ) out lo gpiochip1: GPIOs 32-63, parent: platform/4004a000.gpio, vf610-gpio: gpio-36 ( |scl ) in hi gpio-37 ( |sda ) in hi gpio-40 ( |spi0 CS1 ) out lo gpio-41 ( |spi0 CS0 ) out lo ACTIVE LOW gpio-42 ( |miso ) in hi gpio-43 ( |mosi ) in lo gpio-44 ( |sck ) out lo Signed-off-by:
Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: linux-spi@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
-
Kees Cook authored
[ Upstream commit 7c21383f ] The LLVM linker (ld.lld) defaults to removing local relocations, which causes KASLR boot failures. ld.bfd and ld.gold already handle this correctly. This adds the explicit instruction "--discard-none" during the link phase. There is no change in output for ld.bfd and ld.gold, but ld.lld now produces an image with all the needed relocations. Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: clang-built-linux@googlegroups.com Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20190404214027.GA7324@beast Link: https://github.com/ClangBuiltLinux/linux/issues/404Signed-off-by:
-
Alexei Starovoitov authored
[ Upstream commit 636e78b1 ] clang started to error on invalid asm clobber usage in x86 headers and many bpf program samples failed to build with the message: CLANG-bpf /data/users/ast/bpf-next/samples/bpf/xdp_redirect_kern.o In file included from /data/users/ast/bpf-next/samples/bpf/xdp_redirect_kern.c:14: In file included from ../include/linux/in.h:23: In file included from ../include/uapi/linux/in.h:24: In file included from ../include/linux/socket.h:8: In file included from ../include/linux/uio.h:14: In file included from ../include/crypto/hash.h:16: In file included from ../include/linux/crypto.h:26: In file included from ../include/linux/uaccess.h:5: In file included from ../include/linux/sched.h:15: In file included from ../include/linux/sem.h:5: In file included from ../include/uapi/linux/sem.h:5: In file included from ../include/linux/ipc.h:9: In file included from ../include/linux/refcount.h:72: ../arch/x86/include/asm/refcount.h:72:36: error: asm-specifier for input or output variable conflicts with asm clobber list r->refs.counter, e, "er", i, "cx"); ^ ../arch/x86/include/asm/refcount.h:86:27: error: asm-specifier for input or output variable conflicts with asm clobber list r->refs.counter, e, "cx"); ^ 2 errors generated. Override volatile() to workaround the problem. Signed-off-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Oded Gabbay authored
[ Upstream commit caa3c8e5 ] This patch fixes a bug in the implementation of the function that removes the device. The bug can happen when the device is removed but not the driver itself (e.g. remove by the OS due to PCI freeze in Power architecture). In that case, there maybe open users that are calling IOCTLs while the device is removed. This is a possible race condition that the driver must handle. Otherwise, a kernel panic may occur. This race is prevented in the hard-reset flow, because the driver makes sure the users are closed before continuing with the hard-reset. This race can not occur when the driver itself is removed because the OS makes sure all the file descriptors are closed. The fix is to make sure the open users close their file descriptors and if they don't (after a certain amount of time), the driver sends them a SIGKILL, because the remove of the device can't be stopped. The patch re-uses the same code that is called from the hard-reset flow. Signed-off-by:
Oded Gabbay <oded.gabbay@gmail.com> Signed-off-by:
-
Oded Gabbay authored
[ Upstream commit 9f201aba ] During hard-reset, contexts are closed as part of the tear-down process. After a context is closed, the driver cleans up the page tables of that context in the device's DRAM. This action is both dangerous and unnecessary. It is unnecessary, because the device is going through a hard-reset, which means the device's DRAM contents are no longer valid and the device's MMU is being reset. It is dangerous, because if the hard-reset came as a result of a PCI freeze, this action may cause the entire host machine to hang. Therefore, prevent all device PTE updates when a hard-reset operation is pending. Signed-off-by:
-
David Kozub authored
[ Upstream commit 78bf4735 ] The implementation of IOC_OPAL_ENABLE_DISABLE_MBR handled the value opal_mbr_data.enable_disable incorrectly: enable_disable is expected to be one of OPAL_MBR_ENABLE(0) or OPAL_MBR_DISABLE(1). enable_disable was passed directly to set_mbr_done and set_mbr_enable_disable where is was interpreted as either OPAL_TRUE(1) or OPAL_FALSE(0). The end result was that calling IOC_OPAL_ENABLE_DISABLE_MBR with OPAL_MBR_ENABLE actually disabled the shadow MBR and vice versa. This patch adds correct conversion from OPAL_MBR_DISABLE/ENABLE to OPAL_FALSE/TRUE. The change affects existing programs using IOC_OPAL_ENABLE_DISABLE_MBR but this is typically used only once when setting up an Opal drive. Acked-by:
Jon Derrick <jonathan.derrick@intel.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Scott Bauer <sbauer@plzdonthack.me> Signed-off-by:
David Kozub <zub@linux.fjfi.cvut.cz> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Wen Yang authored
[ Upstream commit b623fa32 ] The call to of_find_compatible_node returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/cpufreq/armada-8k-cpufreq.c:187:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 130, but without a corresponding object release within this function. ./drivers/cpufreq/armada-8k-cpufreq.c:191:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 130, but without a corresponding object release within this function. Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
-
Wen Yang authored
[ Upstream commit ddb64c5d ] The call to of_node_get returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/cpufreq/imx6q-cpufreq.c:391:4-10: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 348, but without a corresponding object release within this function. ./drivers/cpufreq/imx6q-cpufreq.c:395:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 348, but without a corresponding object release within this function. Signed-off-by:
-
Wen Yang authored
[ Upstream commit 7c468966 ] The call to of_get_child_by_name returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/cpufreq/kirkwood-cpufreq.c:127:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 118, but without a corresponding object release within this function. ./drivers/cpufreq/kirkwood-cpufreq.c:133:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 118, but without a corresponding object release within this function. and also do some cleanup: - of_node_put(np); - np = NULL; ... of_node_put(np); Signed-off-by:
-
Wen Yang authored
[ Upstream commit 8d10dc28 ] The call to of_find_node_by_name returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/cpufreq/pmac32-cpufreq.c:557:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function. ./drivers/cpufreq/pmac32-cpufreq.c:569:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function. ./drivers/cpufreq/pmac32-cpufreq.c:598:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 587, but without a corresponding object release within this function. Signed-off-by:
-
Wen Yang authored
[ Upstream commit a9acc26b ] The call to of_get_cpu_node returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/cpufreq/pasemi-cpufreq.c:212:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function. ./drivers/cpufreq/pasemi-cpufreq.c:220:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function. Signed-off-by:
-
Wen Yang authored
[ Upstream commit 23329803 ] The call to of_get_cpu_node returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function. ./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function. Signed-off-by:
-
Huazhong Tan authored
[ Upstream commit 4339ef39 ] This patch adds error handler for the failure of command queue initialization both PF and VF. Signed-off-by:
-
Kristian Evensen authored
[ Upstream commit e4bf6348 ] Most, if not all, Quectel devices use dynamic interface numbers, and users are able to change the USB configuration at will. Matching on for example interface number is therefore not possible. Instead, the QMI device can be identified by looking at the interface class, subclass and protocol (all 0xff), as well as the number of endpoints. The reason we need to look at the number of endpoints, is that the diagnostic port interface has the same class, subclass and protocol as QMI. However, the diagnostic port only has two endpoints, while QMI has three. Until now, we have identified the QMI device by combining a match on class, subclass and protocol, with a call to the function quectel_diag_detect(). In quectel_diag_detect(), we check if the number of endpoints matches for known Quectel vendor/product ids. Adding new vendor/product ids to quectel_diag_detect() is not a good long-term solution. This commit replaces the function with a quirk, and applies the quirk to affected Quectel devices that I have been able to test the change with (EP06, EM12 and EC25). If the quirk is set and the number of endpoints equal two, we return from qmi_wwan_probe() with -ENODEV. Signed-off-by:
Kristian Evensen <kristian.evensen@gmail.com> Acked-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Huazhong Tan authored
[ Upstream commit e233516e ] When hclgevf_client_start() fails or VF driver unloaded, there is nobody to disable keep_alive_timer. So this patch fixes them. Fixes: a6d818e3 ("net: hns3: Add vport alive state checking support") Signed-off-by:
-
