Fore 200 ATM driver fails to handle request_firmware failures and oopses 
when no firmware file was found. Fix it by checking for the right return 
values and propaganting the return value up.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using u32 in this header breaks the build of iptables.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mdc pin should always be output. Initialize it as output,
so each board code does not need to do this.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>

> Kernel BUG at drivers/net/tun.c:444
> invalid opcode: 0000 [1] SMP
> last sysfs file: /class/net/lo/ifindex
> CPU 0
> Modules linked in: tun ipt_MASQUERADE iptable_nat ip_nat xt_state ip_conntrack
> nfnetlink ipt_REJECT xt_tcpudp iptable_filter d
> Pid: 6912, comm: qemu-kvm Tainted: G      2.6.18-128.el5 #1
> RIP: 0010:[<ffffffff886f57b0>]  [<ffffffff886f57b0>]
> :tun:tun_chr_readv+0x2b1/0x3a6
> RSP: 0018:ffff8102202c5e48  EFLAGS: 00010246
> RAX: 0000000000000000 RBX: ffff8102202c5e98 RCX: 0000000004010000
> RDX: ffff810227063680 RSI: ffff8102202c5e9e RDI: ffff8102202c5e92
> RBP: 0000000000010ff6 R08: 0000000000000000 R09: 0000000000000001
> R10: ffff8102202c5e94 R11: 0000000000000202 R12: ffff8102275357c0
> R13: ffff81022755e500 R14: 0000000000000000 R15: ffff8102202c5ef8
> FS:  00002ae4398db980(0000) GS:ffffffff803ac000(0000) knlGS:0000000000000000
> CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
> CR2: 00002ae4ab514000 CR3: 0000000221344000 CR4: 00000000000026e0
> Process qemu-kvm (pid: 6912, threadinfo ffff8102202c4000, task
> ffff81022e58d820)
> Stack:  00000000498735cb ffff810229d1a3c0 0000000000000000 ffff81022e58d820
>  ffffffff8008a461 ffff81022755e528 ffff81022755e528 ffffffff8009f925
>  000005ea05ea0000 ffff8102209d0000 00001051143e1600 ffffffff8003c00e
> Call Trace:
>  [<ffffffff8008a461>] default_wake_function+0x0/0xe
>  [<ffffffff8009f925>] enqueue_hrtimer+0x55/0x70
>  [<ffffffff8003c00e>] hrtimer_start+0xbc/0xce
>  [<ffffffff886f58bf>] :tun:tun_chr_read+0x1a/0x1f
>  [<ffffffff8000b3f3>] vfs_read+0xcb/0x171
>  [<ffffffff800117d4>] sys_read+0x45/0x6e
>  [<ffffffff8005d116>] system_call+0x7e/0x83
>
>
> Code: 0f 0b 68 40 62 6f 88 c2 bc 01 f6 42 0a 08 74 0c 80 4c 24 41
> RIP  [<ffffffff886f57b0>] :tun:tun_chr_readv+0x2b1/0x3a6
>  RSP <ffff8102202c5e48>
>  <0>Kernel panic - not syncing: Fatal exception

This crashed when an LRO packet generated by bnx2x reached a
tun device through the bridge.  We're supposed to drop it at
the bridge.  However, because the check was placed in br_forward
instead of __br_forward, it's only effective if we are sending
the packet through a single port.

This patch fixes it by moving the check into __br_forward.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the user creates IPv6 over IPv6 tunnel, the device name created
by the kernel isn't set to t->parm.name, which is referred as the
result of ioctl().
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ira Snyder found that commit 8c7396ae
"gianfar: Merge Tx and Rx interrupt for scheduling clean up ring" can
cause hangs. It's because there was removed clearing of interrupts in
gfar_schedule_cleanup() (which is called by an interrupt handler) in
case when netif scheduling has been disabled. This patch brings back
this action and a comment.
Reported-by: Ira Snyder <iws@ovro.caltech.edu>
Reported-by: Peter Korsgaard <jacmet@sunsite.dk>
Bisected-by: Ira Snyder <iws@ovro.caltech.edu>
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Tested-by: Ira Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When user tries to map all chunks given in argument, kernel
works on a copy of the chunkmap, but at the end it doesn't
check the copy, but the orginal one.
Signed-off-by: Qu Haoran <haoran.qu@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes echoing if the socket that has sent the request to
create/update/delete an entry is not subscribed to any multicast
group. With the current code, ctnetlink would not send the echo
message via unicast as nfnetlink_send() would be skip.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes an inconsistency in the current ctnetlink code
since NAT sequence adjustment bit can only be updated but not set
in the conntrack entry creation.

This patch is used by conntrackd to successfully recover newly
created entries that represent connections with helpers and NAT
payload mangling.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes connection tracking handling for ICMPv6 messages
related to Stateless Address Autoconfiguration, MLD, and MLDv2. They
can not be tracked because they are massively using multicast (on
pre-defined address). But they are not invalid and should not be
detected as such.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch fixes a typo in the inverse mapping of Node Information
request. Following draft-ietf-ipngwg-icmp-name-lookups-09, "Querier"
sends a type 139 (ICMPV6_NI_QUERY) packet to "Responder" which answer
with a type 140 (ICMPV6_NI_REPLY) packet.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Cut down msi-x vectors from 8 to 1 since only one is used for now.
o Use separate handler for msi-x, that doesn't unnecessarily scrub
  msi status register.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DescOwn should not be set, thus allowing the chip to use the
descriptor, before everything else is set up correctly.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tap devices can make use of a small MAC filter set via the
TUNSETTXFILTER ioctl.  The filter has a set of exact matches
plus a hash for imperfect filtering of additional multicast
addresses.  The current code is unbalanced, adding unicast
addresses to the multicast hash, but only checking the hash
against multicast addresses.  This results in the filter
dropping unicast addresses that overflow the exact filter.
The fix is simply to disable the filter by leaving count set
to zero if we find non-multicast addresses after the exact
match table is filled.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Error handling code following a kmalloc should free the allocated data.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@

(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
     when != if (...) { <+...x...+> }
x->f = E
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Error handling code following a kmalloc should free the allocated data.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@

(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
     when != if (...) { <+...x...+> }
x->f = E
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unfortunately, the OF device tree nodes for SBUS and PCI
hme devices have the same device node name on some systems.

So if the name of the parent node isn't 'sbus', skip it.

Based upon an excellent report and detective work by
Meelis Roos and Eric Brower.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Meelis Roos <mroos@linux.ee>

When the changes were done to the protocol last release, some endian
bugs crept in.  This patch fixes those endian problems and has been
verified to run on 32/64 bit and x86/ppc architectures.

This version of the patch incorporates the correct annotations
for endian variables.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based upon a patch from Atsushi Nemoto <anemo@mba.ocn.ne.jp>

--------------------
The commit 649274d9 ("net_dma:
acquire/release dma channels on ifup/ifdown") added unconditional call
of dmaengine_get() to net_dma.  The API should be called only if
NET_DMA was enabled.
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Dan Williams <dan.j.williams@intel.com>

From: Ondrej Zary <linux@rainbow-software.org>

last year, I posted a patch which fixed hibernation on 3c509
cards. That was back in 2.6.24. It worked fine in 2.6.25. But then I
stopped using hibernation (as it did not work with my new IT8212 RAID
controller).

Now I fixed it and noticed that 3c509 does not wake up properly
anymore (in 2.6.28) - neither in PnP nor in ISA modes. ifconfig
down/up makes the card work again in PnP mode. However, in ISA mode,
ifconfig up ends with "No such device" error.

Comparing the 3c509 driver between 2.6.25 and 2.6.28, there's only
some statistics-related change. So the cause of the problem must be
somewhere else.

This patch makes the resume work in PnP mode, but it's still not
enough for ISA mode.
Signed-off-by: David S. Miller <davem@davemloft.net>

From: Ilkka Virta <itvirta@iki.fi>

In the lockup situation the driver seems to go off in an eternal storm
of interrupts right after calling request_irq(). It doesn't actually
do anything interesting in the interrupt handler. Since connecting the link
afterwards works, something later in initialization must fix this.

Looking at gem_do_start() and gem_open(), it seems that the only thing
done while opening the device after the request_irq(), is a call to
napi_enable().

I don't know what the ordering requirements are for the
initialization, but I boldly tried to move the napi_enable() call
inside gem_do_start() before the link state is checked and interrupts
subsequently enabled, and it seems to work for me. Doesn't even break
anything too obvious...
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a potential NULL dereference bug during error handling in
rxrpc_kernel_begin_call(), whereby rxrpc_put_transport() may be handed a NULL
pointer.

This was found with a code checker (http://repo.or.cz/w/smatch.git/).
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some Realtek chips (RTL8169sb/8110sb in my case) are unable to retrieve
ethtool statistics when the interface is down. The process stays in
endless loop in rtl8169_get_ethtool_stats. This is because these chips
need to have receiver enabled (CmdRxEnb bit in ChipCmd register) that is
cleared when the interface is going down. It's better to update statistics
only when the interface is up and otherwise return copy of statistics
grabbed when the interface was up (in rtl8169_close).

It is interesting that PCI-E NICs (like 8168b/8111b...) are not affected.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like the UDP header fix, pskb_may_pull() can potentially
alter the SKB buffer.  Thus the saddr and daddr, pointers
may point to the old skb->data buffer.

I haven't seen corruptions, as its only seen if the old
skb->data buffer were reallocated by another user and
written into very quickly (or poison'd by SLAB debugging).
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

neightbl_dump_info and neigh_dump_table  can skip entries if the
*fill*info functions return an error. This results in an incomplete
dump ((invoked by netlink requests for RTM_GETNEIGHTBL or
RTM_GETNEIGH)

nidx and idx should not be incremented if the current entry was not
placed in the output buffer
Signed-off-by: Gautam Kachroo <gk@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just like PKTINFO, limit the options area to 64K.

Based upon report by Eric Sesterhenn and analysis by
Roland Dreier.
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 64ff3b93.

Jeff Chua reports that it breaks rlogin for him.
Signed-off-by: David S. Miller <davem@davemloft.net>

As the options passed to ip6_append_data may be ephemeral, we need
to duplicate it for corking.  This patch applies the simplest fix
which is to memdup all the relevant bits.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The UDP header pointer assignment must happen after calling
pskb_may_pull().  As pskb_may_pull() can potentially alter the SKB
buffer.

This was exposted by running multicast traffic through the NIU driver,
as it won't prepull the protocol headers into the linear area on
receive.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

SOFT_RESET must be asserted for at least 3 TX clocks in order for it to work
properly.  The syncs in the gfar_write() commands have been hiding this, but
we need to guarantee it.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

BD_LENGTH_MASK is supposed to catch the low 16-bits of the status field, not
the low byte.  The old way, we would never be able to clean up tx packets with
sizes divisible by 256.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The LRO switch is always set to 1 in the rx processing loop.
It breaks the accelerated iSCSI receive traffic.
Fix its computation.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is the right thing to do and fixes the following warning:

[  115.012278] ------------[ cut here ]------------
[  115.012281] WARNING: at drivers/pci/pci-driver.c:370
pci_legacy_suspend+0x85/0xc2()
[  115.012285] Hardware name: Latitude D630
[  115.012301] PCI PM: Device state not saved by
iwl3945_pci_suspend+0x0/0x4c [iwl3945]
[  115.012304] Modules linked in: fuse nfsd lockd nfs_acl auth_rpcgss
exportfs sunrpc ipv6 acpi_cpufreq kvm_intel kvm snd_hda_codec_idt
snd_hda_intel snd_hda_codec snd_hwdep arc4 snd_seq_device snd_pcm_oss
snd_mixer_oss ecb snd_pcm cryptomgr aead snd_timer crypto_blkcipher
snd snd_page_alloc ohci1394 crypto_hash crypto_algapi ch341 ieee1394
usbserial thermal iwl3945 mac80211 led_class lib80211 tg3 processor
i2c_i801 i2c_core sg cfg80211 libphy usbhid battery ac button sr_mod
cdrom evdev dcdbas ata_generic ata_piix libata sd_mod scsi_mod ext3
jbd mbcache uhci_hcd ohci_hcd ehci_hcd usbcore [last unloaded:
microcode]
[  115.012374] Pid: 4163, comm: pm-suspend Not tainted
2.6.29-rc3-00227-gf1dd849-dirty #67
[  115.012377] Call Trace:
[  115.012382]  [<ffffffff8023d04d>] warn_slowpath+0xb1/0xed
[  115.012387]  [<ffffffff80450b5e>] ? _spin_unlock_irqrestore+0x5c/0x78
[  115.012390]  [<ffffffff80254f08>] ? up+0x34/0x39
[  115.012394]  [<ffffffff80362319>] ? acpi_ut_release_mutex+0x5d/0x61
[  115.012397]  [<ffffffff803584b2>] ? acpi_get_data+0x5e/0x70
[  115.012400]  [<ffffffff80363dd9>] ? acpi_bus_get_device+0x25/0x39
[  115.012403]  [<ffffffff80363e98>] ? acpi_bus_power_manageable+0x11/0x29
[  115.012406]  [<ffffffff803462f7>] ? acpi_pci_power_manageable+0x17/0x19
[  115.012410]  [<ffffffff8033ddfd>] ? pci_set_power_state+0xcc/0x101
[  115.012418]  [<ffffffffa01f28e9>] ? iwl3945_pci_suspend+0x0/0x4c [iwl3945]
[  115.012422]  [<ffffffff803401e6>] pci_legacy_suspend+0x85/0xc2
[  115.012425]  [<ffffffff80340316>] pci_pm_suspend+0x34/0x86
[  115.012429]  [<ffffffff8039d7ce>] pm_op+0x52/0xe5
[  115.012432]  [<ffffffff8039dd78>] device_suspend+0x32a/0x451
[  115.012436]  [<ffffffff80269ec2>] suspend_devices_and_enter+0x3e/0x13a
[  115.012439]  [<ffffffff8026a128>] enter_state+0x110/0x164
[  115.012442]  [<ffffffff8026a233>] state_store+0xb7/0xd7
[  115.012446]  [<ffffffff8032f95f>] kobj_attr_store+0x17/0x19
[  115.012449]  [<ffffffff80307d64>] sysfs_write_file+0xe4/0x119
[  115.012453]  [<ffffffff802baa7a>] vfs_write+0xae/0x137
[  115.012456]  [<ffffffff802babc7>] sys_write+0x47/0x70
[  115.012459]  [<ffffffff8020b73a>] system_call_fastpath+0x16/0x1b
[  115.012467] ---[ end trace 829828966f6f24dc ]---
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Cleans uCode key table bit map iwl_clear_stations_table
since all stations are cleared also the key table must be.

Since the keys are not removed properly on suspend by mac80211
this may result in exhausting key table on resume leading
to memory corruption during removal
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix sunrpc/rdma build dependencies.
Survives 12 build combinations of INET, IPV6, SUNRPC,
INFINIBAND, and INFINIBAND_ADDR_TRANS.

ERROR: "rdma_destroy_id" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_connect" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_destroy_qp" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_create_id" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_create_qp" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_resolve_route" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_disconnect" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_resolve_addr" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_accept" [net/sunrpc/xprtrdma/svcrdma.ko] undefined!
ERROR: "rdma_destroy_id" [net/sunrpc/xprtrdma/svcrdma.ko] undefined!
ERROR: "rdma_listen" [net/sunrpc/xprtrdma/svcrdma.ko] undefined!
ERROR: "rdma_create_id" [net/sunrpc/xprtrdma/svcrdma.ko] undefined!
ERROR: "rdma_create_qp" [net/sunrpc/xprtrdma/svcrdma.ko] undefined!
ERROR: "rdma_bind_addr" [net/sunrpc/xprtrdma/svcrdma.ko] undefined!
ERROR: "rdma_disconnect" [net/sunrpc/xprtrdma/svcrdma.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On machine were no IO ports are assigned the call
to pci_enable_device() will fail, even if need_ioport
is false, we need to use pci_enable_device_mem() here.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

A recent patch by Stephen Hemminger to convert XPNET to use net_device_ops and
internal net_device_stats failed to link the net_device_ops structure to the
net_device structure. See commit e8ac9c55
("xpnet: convert devices to new API").
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>