Move the "ISDN4Linux interface" message from device registration,
where it is emitted for each device, to driver registration, where
it is emitted only once, for consistency with the CAPI variant.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/networking/ifenslave.c: In function ‘if_getconfig’:
Documentation/networking/ifenslave.c:508:14: warning: variable ‘mtu’ set but not used [-Wunused-but-set-variable]
Documentation/networking/ifenslave.c:508:6: warning: variable ‘metric’ set but not used [-Wunused-but-set-variable]

The purpose of this function is to simply print out the values
it probes, so...
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Chas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tx_fifo_errors are tracked in start_xmit_ for virtio_net, but not
reported in the tallies returned by virtnet_stats().  Return them
as the rx "sub-stats" rx_length_errors and rx_frame_errors are.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

rx_msg is defined to have a 1 entry array at the end, so gcc warns:

drivers/net/wireless/ray_cs.c: In function ‘rx_authenticate’:
drivers/net/wireless/ray_cs.c:2436:3: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2436:3: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2436:3: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2436:3: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2436:3: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2439:15: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2452:16: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2453:18: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2453:32: warning: array subscript is above array bounds [-Warray-bounds]

Use a zero length array and rename to "ray_rx_msg" to make sure we hit all
of the necessary cases.
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/wireless/airo.c: In function ‘encapsulate’:
drivers/net/wireless/airo.c:1421:15: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/airo.c: In function ‘decapsulate’:
drivers/net/wireless/airo.c:1509:16: warning: array subscript is above array bounds [-Warray-bounds]
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ethtool EEPROM read/write support using the eeprom_93cx6
library instead of open-coding the functions.

Depends on eeprom_93cx6 driver getting EEPROM write support.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
[sboyd@codeaurora.org: Removed previous eeprom implementation]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When device is off it is under power saving mode. Changing the MAC address
in that situation will result in the device not communicating as the first
write to the MAC address register is not executed.
Signed-off-by: Tristram Ha <Tristram.Ha@micrel.com>
[ben@simtec.co.uk: cleaned up header]
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for reading the MAC address from the system registers if there
is an EEPROM present. This involves caching the KS_CCR register for later
use (will also be useful for ETHTOOL support) and adding a print to say
that there is an EEPROM present.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for writing data to EEPROM.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Linux Kernel <linux-kernel@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some devices need to know if the data is to be output or read, so add a
data direction into the eeprom structure to tell the driver whether the
data line should be driven.

The user in this case is the Micrel KS8851 which has a direction
control for the EEPROM data line and thus needs to know whether
to drive it (writing) or to tristate it for receiving.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When non power of two MSIX vectors are given to driver, some RX queues
are not utilized. Program RSS table in such a way that all queues
are utilized.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This new hash key gives better distribution of packets across RX
queues.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Detect error in Lancer by polling a HW register and
recover from this error if it is recoverable.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When TX queues are created again after error recovery,
netif_set_real_num_tx_queues() is invoked to update number of real
TX queues created. rtnl lock needs to be held when invoking this routine.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SR-IOV implementation is Lancer has changed in following ways -
1)PF driver assigns one MAC addresses for VF using COMMON_SET_IFACE_MAC_LIST.
2)VF driver queries its MAC address using COMMON_GET_IFACE_MAC_LIST command
and assigns it to its interface.
Signed-off-by: Mammatha Edhala <mammatha.edhala@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This file is now unused and should have been removed by commit
7c899432 ("bonding, ipv4, ipv6, vlan:
Handle NETDEV_BONDING_FAILOVER like NETDEV_NOTIFY_PEERS").
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the kconfig types to tristate and adjust the condition for
declaring net_device::dsa_ptr to allow for this.

Adjust the makefile so that if NET_DSA_MV88E6123_61_65=y and
NET_DSA_MV88E6131=m or vice versa then both drivers are built-in.  We
could leave these options as bool and make NET_DSA_MV88E6XXX a
user-selected option, but that would break existing configurations.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

These drivers share a lot of code, so if we make them modular they
should be built into the same module.  Therefore, link them together
and merge their respective module init and exit functions.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

These files have circular dependencies, so if we make DSA modular then
they must be built into the same module.  Therefore, link them
together and merge their respective module init and exit functions.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

eth_type_trans() will use these functions if DSA is enabled, which
blocks building DSA as a module.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	net/ipv4/inet_diag.c

commit 88491d81 ("drivers/net: Kconfig
& Makefile cleanup") changed the type of these options to bool, but
they select code that could (and still can) be built as modules.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pmtu informations on the inetpeer are visible for output and
input routes. On packet forwarding, we might propagate a learned
pmtu to the sender. As we update the pmtu informations of the
inetpeer on demand, the original sender of the forwarded packets
might never notice when the pmtu to that inetpeer increases.
So use the mtu of the outgoing device on packet forwarding instead
of the pmtu to the final destination.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We move all mtu handling from dst_mtu() down to the protocol
layer. So each protocol can implement the mtu handling in
a different manner.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We plan to invoke the dst_opt->default_mtu() method unconditioally
from dst_mtu(). So rename the method to dst_opt->mtu() to match
the name with the new meaning.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As it is, we return null as the default mtu of blackhole routes.
This may lead to a propagation of a bogus pmtu if the default_mtu
method of a blackhole route is invoked. So return dst->dev->mtu
as the default mtu instead.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Skip entries from foreign network namespaces.
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This was copy and pasted from the IPv4 code.  We're calling the
ip4 version of that function and map4 is NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix below build error:
  CC      drivers/net/ethernet/marvell/mv643xx_eth.o
drivers/net/ethernet/marvell/mv643xx_eth.c: In function 'mv643xx_eth_get_drvinfo':
drivers/net/ethernet/marvell/mv643xx_eth.c:1505: error: 'info' undeclared (first use in this function)
drivers/net/ethernet/marvell/mv643xx_eth.c:1505: error: (Each undeclared identifier is reported only once
drivers/net/ethernet/marvell/mv643xx_eth.c:1505: error: for each function it appears in.)
make[4]: *** [drivers/net/ethernet/marvell/mv643xx_eth.o] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can not update iph->daddr in ip_options_rcv_srr(), It is too early.
When some exception ocurred later (eg. in ip_forward() when goto
sr_failed) we need the ip header be identical to the original one as
ICMP need it.

Add a field 'nexthop' in struct ip_options to save nexthop of LSRR
or SSRR option.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use round_jiffies_relative to align the ehea workqueue and avoid
extra wakeups.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we enable multiqueue by default the ehea driver is using
quite a lot of memory for its buffer pools. With 4 queues we
consume 64MB in the jumbo packet ring, 16MB in the medium packet
ring and 16MB in the tiny packet ring.

We should only fill the jumbo ring once the MTU is increased but
for now halve it's size so it consumes 32MB. Also reduce the tiny
packet ring, with 4 queues we had 16k entries which is overkill.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When transmiting a fragmented skb, qlge fills a descriptor with the
fragment addresses, after DMA-mapping them. If there are more than eight
fragments, it will use the eighth descriptor as a pointer to an external
list. After mapping this external list, called OAL to a structure
containing more descriptors, it fills it with the extra fragments.

However, considering that systems with pages larger than 8KiB would have
less than 8 fragments, which was true before commit a715dea3, it
defined a macro for the OAL size as 0 in those cases.

Now, if a skb with more than 8 fragments (counting skb->data as one
fragment), this would start overwriting the list of addresses already
mapped and would make the driver fail to properly unmap the right
addresses on architectures with pages larger than 8KiB.

Besides that, the list of mappings was one size too small, since it must
have a mapping for the maxinum number of skb fragments plus one for
skb->data and another for the OAL. So, even on architectures with page
sizes 4KiB and 8KiB, a skb with the maximum number of fragments would
make the driver overwrite its counter for the number of mappings, which,
again, would make it fail to unmap the mapped DMA addresses.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix port identify test on 5461x PHY by driving LEDs through MDIO.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>