Pull documentation fixes from Jonathan Corbet:
 "A handful of documentation fixes.

  The most significant of these addresses a problem with the new warning
  mode: it can break the build when confronted with a source file
  containing malformed kerneldoc comments"

* tag 'docs-4.15-fixes' of git://git.lwn.net/linux:
  Documentation: fix docs build error after source file removed
  scsi: documentation: Fix case of 'scsi_device' struct mention(s)
  genericirq.rst: Remove :c:func:`...` in code blocks
  dmaengine: doc : Fix warning "Title underline too short" while make xmldocs
  scripts/kernel-doc: Don't fail with status != 0 if error encountered with -none

Pull virtio fixes from Michael Tsirkin:
 "virtio and qemu bugfixes

  A couple of bugfixes that just became ready"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_balloon: fix increment of vb->num_pfns in fill_balloon()
  virtio: release virtio index when fail to device_register
  fw_cfg: fix driver remove

Pull networking fixes from David Miller:

 1) Various TCP control block fixes, including one that crashes with
    SELinux, from David Ahern and Eric Dumazet.

 2) Fix ACK generation in rxrpc, from David Howells.

 3) ipvlan doesn't set the mark properly in the ipv4 route lookup key,
    from Gao Feng.

 4) SIT configuration doesn't take on the frag_off ipv4 field
    configuration properly, fix from Hangbin Liu.

 5) TSO can fail after device down/up on stmmac, fix from Lars Persson.

 6) Various bpftool fixes (mostly in JSON handling) from Quentin Monnet.

 7) Various SKB leak fixes in vhost/tun/tap (mostly observed as
    performance problems). From Wei Xu.

 8) mvpps's TX descriptors were not zero initialized, from Yan Markman.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
  tcp: use IPCB instead of TCP_SKB_CB in inet_exact_dif_match()
  tcp: add tcp_v4_fill_cb()/tcp_v4_restore_cb()
  rxrpc: Fix the MAINTAINERS record
  rxrpc: Use correct netns source in rxrpc_release_sock()
  liquidio: fix incorrect indentation of assignment statement
  stmmac: reset last TSO segment size after device open
  ipvlan: Add the skb->mark as flow4's member to lookup route
  s390/qeth: build max size GSO skbs on L2 devices
  s390/qeth: fix GSO throughput regression
  s390/qeth: fix thinko in IPv4 multicast address tracking
  tap: free skb if flags error
  tun: free skb in early errors
  vhost: fix skb leak in handle_rx()
  bnxt_en: Fix a variable scoping in bnxt_hwrm_do_send_msg()
  bnxt_en: fix dst/src fid for vxlan encap/decap actions
  bnxt_en: wildcard smac while creating tunnel decap filter
  bnxt_en: Need to unconditionally shut down RoCE in bnxt_shutdown
  phylink: ensure we take the link down when phylink_stop() is called
  sfp: warn about modules requiring address change sequence
  sfp: improve RX_LOS handling
  ...

The chip family of TILEPro and TILE-Gx was developed by Tilera, which
was eventually acquired by Mellanox.  The tile architecture was added to
the kernel in 2010 and first appeared in 2.6.36.

Now at Mellanox we are developing new chips based on the ARM64
architecture; our last TILE-Gx chip (the Gx72) was released in 2013, and
our customers using tile architecture products are not, as far as we
know, looking to upgrade to newer kernel releases.  In the absence of
someone in the community stepping up to take over maintainership, this
commit marks the architecture as orphaned.

Cc: Chris Metcalf <metcalf@alum.mit.edu>
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The pci/htirq.c file was removed so remove it from the documentation
file also.

Error: Cannot open file ../drivers/pci/htirq.c
WARNING: kernel-doc '../scripts/kernel-doc -rst -enable-lineno -export ../drivers/pci/htirq.c' failed with return code 2

Fixes: fd2fa6c1 ("x86/PCI: Remove unused HyperTransport interrupt support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

Daniel Borkmann says:

====================
pull-request: bpf 2017-12-02

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix a compilation warning in xdp redirect tracepoint due to
   missing bpf.h include that pulls in struct bpf_map, from Xie.

2) Limit the maximum number of attachable BPF progs for a given
   perf event as long as uabi is not frozen yet. The hard upper
   limit is now 64 and therefore the same as with BPF multi-prog
   for cgroups. Also add related error checking for the sample
   BPF loader when enabling and attaching to the perf event, from
   Yonghong.

3) Specifically set the RLIMIT_MEMLOCK for the test_verifier_log
   case, so that the test case can always pass and not fail in
   some environments due to too low default limit, also from
   Yonghong.

4) Fix up a missing license header comment for kernel/bpf/offload.c,
   from Jakub.

5) Several fixes for bpftool, among others a crash on incorrect
   arguments when json output is used, error message handling
   fixes on unknown options and proper destruction of json writer
   for some exit cases, all from Quentin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
tcp: add tcp_v4_fill_cb()/tcp_v4_restore_cb()

James Morris reported kernel stack corruption bug that
we tracked back to commit 971f10ec ("tcp: better TCP_SKB_CB
layout to reduce cache line misses")

First patch needs to be backported to kernels >= 3.18,
while second patch needs to be backported to kernels >= 4.9, since
this was the time when inet_exact_dif_match appeared.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After this fix : ("tcp: add tcp_v4_fill_cb()/tcp_v4_restore_cb()"),
socket lookups happen while skb->cb[] has not been mangled yet by TCP.

Fixes: a04a480d ("net: Require exact match for TCP socket lookups if dif is l3mdev")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

James Morris reported kernel stack corruption bug [1] while
running the SELinux testsuite, and bisected to a recent
commit bffa72cf ("net: sk_buff rbnode reorg")

We believe this commit is fine, but exposes an older bug.

SELinux code runs from tcp_filter() and might send an ICMP,
expecting IP options to be found in skb->cb[] using regular IPCB placement.

We need to defer TCP mangling of skb->cb[] after tcp_filter() calls.

This patch adds tcp_v4_fill_cb()/tcp_v4_restore_cb() in a very
similar way we added them for IPv6.

[1]
[  339.806024] SELinux: failure in selinux_parse_skb(), unable to parse packet
[  339.822505] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffffff81745af5
[  339.822505]
[  339.852250] CPU: 4 PID: 3642 Comm: client Not tainted 4.15.0-rc1-test #15
[  339.868498] Hardware name: LENOVO 10FGS0VA1L/30BC, BIOS FWKT68A   01/19/2017
[  339.885060] Call Trace:
[  339.896875]  <IRQ>
[  339.908103]  dump_stack+0x63/0x87
[  339.920645]  panic+0xe8/0x248
[  339.932668]  ? ip_push_pending_frames+0x33/0x40
[  339.946328]  ? icmp_send+0x525/0x530
[  339.958861]  ? kfree_skbmem+0x60/0x70
[  339.971431]  __stack_chk_fail+0x1b/0x20
[  339.984049]  icmp_send+0x525/0x530
[  339.996205]  ? netlbl_skbuff_err+0x36/0x40
[  340.008997]  ? selinux_netlbl_err+0x11/0x20
[  340.021816]  ? selinux_socket_sock_rcv_skb+0x211/0x230
[  340.035529]  ? security_sock_rcv_skb+0x3b/0x50
[  340.048471]  ? sk_filter_trim_cap+0x44/0x1c0
[  340.061246]  ? tcp_v4_inbound_md5_hash+0x69/0x1b0
[  340.074562]  ? tcp_filter+0x2c/0x40
[  340.086400]  ? tcp_v4_rcv+0x820/0xa20
[  340.098329]  ? ip_local_deliver_finish+0x71/0x1a0
[  340.111279]  ? ip_local_deliver+0x6f/0xe0
[  340.123535]  ? ip_rcv_finish+0x3a0/0x3a0
[  340.135523]  ? ip_rcv_finish+0xdb/0x3a0
[  340.147442]  ? ip_rcv+0x27c/0x3c0
[  340.158668]  ? inet_del_offload+0x40/0x40
[  340.170580]  ? __netif_receive_skb_core+0x4ac/0x900
[  340.183285]  ? rcu_accelerate_cbs+0x5b/0x80
[  340.195282]  ? __netif_receive_skb+0x18/0x60
[  340.207288]  ? process_backlog+0x95/0x140
[  340.218948]  ? net_rx_action+0x26c/0x3b0
[  340.230416]  ? __do_softirq+0xc9/0x26a
[  340.241625]  ? do_softirq_own_stack+0x2a/0x40
[  340.253368]  </IRQ>
[  340.262673]  ? do_softirq+0x50/0x60
[  340.273450]  ? __local_bh_enable_ip+0x57/0x60
[  340.285045]  ? ip_finish_output2+0x175/0x350
[  340.296403]  ? ip_finish_output+0x127/0x1d0
[  340.307665]  ? nf_hook_slow+0x3c/0xb0
[  340.318230]  ? ip_output+0x72/0xe0
[  340.328524]  ? ip_fragment.constprop.54+0x80/0x80
[  340.340070]  ? ip_local_out+0x35/0x40
[  340.350497]  ? ip_queue_xmit+0x15c/0x3f0
[  340.361060]  ? __kmalloc_reserve.isra.40+0x31/0x90
[  340.372484]  ? __skb_clone+0x2e/0x130
[  340.382633]  ? tcp_transmit_skb+0x558/0xa10
[  340.393262]  ? tcp_connect+0x938/0xad0
[  340.403370]  ? ktime_get_with_offset+0x4c/0xb0
[  340.414206]  ? tcp_v4_connect+0x457/0x4e0
[  340.424471]  ? __inet_stream_connect+0xb3/0x300
[  340.435195]  ? inet_stream_connect+0x3b/0x60
[  340.445607]  ? SYSC_connect+0xd9/0x110
[  340.455455]  ? __audit_syscall_entry+0xaf/0x100
[  340.466112]  ? syscall_trace_enter+0x1d0/0x2b0
[  340.476636]  ? __audit_syscall_exit+0x209/0x290
[  340.487151]  ? SyS_connect+0xe/0x10
[  340.496453]  ? do_syscall_64+0x67/0x1b0
[  340.506078]  ? entry_SYSCALL64_slow_path+0x25/0x25

Fixes: 971f10ec ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: James Morris <james.l.morris@oracle.com>
Tested-by: James Morris <james.l.morris@oracle.com>
Tested-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ARM fix from Russell King:
 "Just one fix this time around, for the late commit in the merge window
  that triggered a problem with qemu. Qemu is apparently also going to
  receive a fix for the discovered issue"

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: avoid faulting on qemu

Pull i2c fixes from Wolfram Sang:
 "Here are two bugfixes for I2C, fixing a memleak in the core and irq
  allocation for i801.

  Also three bugfixes for the at24 eeprom driver which Bartosz collected
  while taking over maintainership for this driver"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  eeprom: at24: check at24_read/write arguments
  eeprom: at24: fix reading from 24MAC402/24MAC602
  eeprom: at24: correctly set the size for at24mac402
  i2c: i2c-boardinfo: fix memory leaks on devinfo
  i2c: i801: Fix Failed to allocate irq -2147483648 error

Merge tag 'hwmon-for-linus-v4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
 "Fixes:

   - Drop reference to obsolete maintainer tree

   - Fix overflow bug in pmbus driver

   - Fix SMBUS timeout problem in jc42 driver

  For the SMBUS timeout handling, we had a brief discussion if this
  should be considered a bug fix or a feature. Peter says "it fixes real
  problems where the application misbehave due to faulty content when
  reading from an eeprom", and he needs the patch in his company's v4.14
  images. This is good enough for me and warrants backport to stable
  kernels"

* tag 'hwmon-for-linus-v4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (jc42) optionally try to disable the SMBUS timeout
  hwmon: (pmbus) Use 64bit math for DIRECT format values
  hwmon: Drop reference to Jean's tree

Fix the MAINTAINERS record so that it's more obvious who the maintainer for
AF_RXRPC is.
Reported-by: Joe Perches <joe@perches.com>
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In rxrpc_release_sock() there may be no rx->local value to access, so we
can't unconditionally follow it to the rxrpc network namespace information
to poke the connection reapers.

Instead, use the socket's namespace pointer to find the namespace.

This unfixed code causes the following static checker warning:

	net/rxrpc/af_rxrpc.c:898 rxrpc_release_sock()
	error: we previously assumed 'rx->local' could be null (see line 887)

Fixes: 3d18cbb7 ("rxrpc: Fix conn expiry timers")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove one extraneous level of indentation on assignment statement.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.15-20171201' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2017-12-01

this is a pull for net consisting of nine patches.

The first three patches are by Jimmy Assarsson for the kvaser_usb driver
and add the missing free()s in some error path, a signed/unsigned
comparison and ratelimit the error messages in case of incomplete
messages. Oliver Stäbler's patch for the ti_hecc driver fix the napi
poll function's return value. The return values of the probe function of
the peak_canfd and peak_pci PCI drivers are fixed by Stephane Grosjean's
patch. Two patches by me for the flexcan driver update the
bugs/features/quirks overview table and fix the error state transition
for the VF610 SoC. The two patches by Martin Kelly for the mcba_usb
driver fix a typo and a device disconnect bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'at24-4.15-fixes-for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-current

Please consider pulling the following fixes for v4.15. While it doesn't
fix any regression introduced in the v4.15 merge window, we have a
feature in at24 since linux v4.8 - reading the mac address block from
at24mac series - which turned out to be not working.

This pull request contains changes that fix it together with a patch
that hardens the read and write argument sanitization with
out-of-bounds checks that were missing.

The mss variable tracks the last max segment size sent to the TSO
engine. We do not update the hardware as long as we receive skb:s with
the same value in gso_size.

During a network device down/up cycle (mapped to stmmac_release() and
stmmac_open() callbacks) we issue a reset to the hardware and it
forgets the setting for mss. However we did not zero out our mss
variable so the next transmission of a gso packet happens with an
undefined hardware setting.

This triggers a hang in the TSO engine and eventuelly the netdev
watchdog will bark.

Fixes: f748be53 ("stmmac: support new GMAC4")
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current codes don't use skb->mark to assign flowi4_mark, it would
make the policy route rule with fwmark doesn't work as expected.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: fixes 2017-12-01

please apply the following three fixes for 4.15. These should also go
back to stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The current GSO skb size limit was copy&pasted over from the L3 path,
where it is needed due to a TSO limitation.
As L2 devices don't offer TSO support (and thus all GSO skbs are
segmented before they reach the driver), there's no reason to restrict
the stack in how large it may build the GSO skbs.

Fixes: d52aec97 ("qeth: enable scatter/gather in layer 2 mode")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using GSO with small MTUs currently results in a substantial throughput
regression - which is caused by how qeth needs to map non-linear skbs
into its IO buffer elements:
compared to a linear skb, each GSO-segmented skb effectively consumes
twice as many buffer elements (ie two instead of one) due to the
additional header-only part. This causes the Output Queue to be
congested with low-utilized IO buffers.

Fix this as follows:
If the MSS is low enough so that a non-SG GSO segmentation produces
order-0 skbs (currently ~3500 byte), opt out from NETIF_F_SG. This is
where we anticipate the biggest savings, since an SG-enabled
GSO segmentation produces skbs that always consume at least two
buffer elements.

Larger MSS values continue to get a SG-enabled GSO segmentation, since
1) the relative overhead of the additional header-only buffer element
becomes less noticeable, and
2) the linearization overhead increases.

With the throughput regression fixed, re-enable NETIF_F_SG by default to
reap the significant CPU savings of GSO.

Fixes: 5722963a ("qeth: do not turn on SG per default")
Reported-by: Nils Hoppmann <niho@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 5f78e29c ("qeth: optimize IP handling in rx_mode callback")
reworked how secondary addresses are managed for qeth devices.
Instead of dropping & subsequently re-adding all addresses on every
ndo_set_rx_mode() call, qeth now keeps track of the addresses that are
currently registered with the HW.
On a ndo_set_rx_mode(), we thus only need to do (de-)registration
requests for the addresses that have actually changed.

On L3 devices, the lookup for IPv4 Multicast addresses checks the wrong
hashtable - and thus never finds a match. As a result, we first delete
*all* such addresses, and then re-add them again. So each set_rx_mode()
causes a short period where the IPv4 Multicast addresses are not
registered, and the card stops forwarding inbound traffic for them.

Fix this by setting the ->is_multicast flag on the lookup object, thus
enabling qeth_l3_ip_from_hash() to search the correct hashtable and
find a match there.

Fixes: 5f78e29c ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wei Xu says:

====================
vhost: fix a few skb leaks

Matthew found a roughly 40% tcp throughput regression with commit
c67df11f(vhost_net: try batch dequing from skb array) as discussed
in the following thread:
https://www.mail-archive.com/netdev@vger.kernel.org/msg187936.html

v4:
- fix zero iov iterator count in tap/tap_do_read()(Jason)
- don't put tun in case of EBADFD(Jason)
- Replace msg->msg_control with new 'skb' when calling tun/tap_do_read()

v3:
- move freeing skb from vhost to tun/tap recvmsg() to not
  confuse the callers.

v2:
- add Matthew as the reporter, thanks matthew.
- moving zero headcount check ahead instead of defer consuming skb
  due to jason and mst's comment.
- add freeing skb in favor of recvmsg() fails.
====================
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tap_recvmsg() supports accepting skb by msg_control after
commit 3b4ba04a ("tap: support receiving skb from msg_control"),
the skb if presented should be freed within the function, otherwise
it would be leaked.
Signed-off-by: Wei Xu <wexu@redhat.com>
Reported-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tun_recvmsg() supports accepting skb by msg_control after
commit ac77cfd4 ("tun: support receiving skb through msg_control"),
the skb if presented should be freed no matter how far it can go
along, otherwise it would be leaked.

This patch fixes several missed cases.
Signed-off-by: Wei Xu <wexu@redhat.com>
Reported-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Matthew found a roughly 40% tcp throughput regression with commit
c67df11f(vhost_net: try batch dequing from skb array) as discussed
in the following thread:
https://www.mail-archive.com/netdev@vger.kernel.org/msg187936.html

Eventually we figured out that it was a skb leak in handle_rx()
when sending packets to the VM. This usually happens when a guest
can not drain out vq as fast as vhost fills in, afterwards it sets
off the traffic jam and leaks skb(s) which occurs as no headcount
to send on the vq from vhost side.

This can be avoided by making sure we have got enough headcount
before actually consuming a skb from the batched rx array while
transmitting, which is simply done by moving checking the zero
headcount a bit ahead.
Signed-off-by: Wei Xu <wexu@redhat.com>
Reported-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Fixes.

A shutdown fix for SMARTNIC, 2 fixes related to TC Flower vxlan
filters, and the last one fixes an out-of-scope variable when sending
short firmware messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

short_input variable is assigned to another data pointer which is
referred out of its scope. Fix it by moving short_input definition
to the beginning of bnxt_hwrm_do_send_msg() function.

No failure has been reported so far due to this issue.

Fixes: e605db80 ("bnxt_en: Support for Short Firmware Message")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For flows that involve a vxlan encap action, the vxlan sock
interface may be specified as the outgoing interface. The driver
must resolve the outgoing PF interface used by this socket and
use the dst_fid of the PF in the hwrm_cfa_encap_record_alloc cmd.

Similarily for flows that have a vxlan decap action, the
fid of the incoming PF interface must be used as the src_fid in
the hwrm_cfa_decap_filter_alloc cmd.

Fixes: 8c95f773 ("bnxt_en: add support for Flower based vxlan encap/decap offload")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While creating a decap filter the tunnel smac need not (and must not) be
specified as we cannot ascertain the neighbor in the recv path. 'ttl'
match is also not needed for the decap filter and must be wild-carded.

Fixes: f484f678 ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter")
Signed-off-by: Sunil Challa <sunilkumar.challa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current 'bnxt_shutdown' implementation only invokes
'bnxt_ulp_shutdown' to shut down RoCE in the case when the system is in
the path of power off (SYSTEM_POWER_OFF). While this may work in most
cases, it does not work in the smart NIC case, when Linux 'reboot'
command is initiated from the Linux that runs on the ARM cores of the
NIC card. In this particular case, Linux 'reboot' results in a system
'L3' level reset where the entire ARM and associated subsystems are
being reset, but at the same time, Nitro core is being kept in sane state
(to allow external PCIe connected servers to continue to work). Without
properly shutting down RoCE and freeing all associated resources, it
results in the ARM core to hang immediately after the 'reboot'

By always invoking 'bnxt_ulp_shutdown' in 'bnxt_shutdown', it fixes the
above issue

Fixes: 0efd2fc6 ("bnxt_en: Add a callback to inform RDMA driver during PCI shutdown.")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In scsi_mid_low_api.txt a the scsi_device structure is mentioned
several times, but the leading 's' is uppercase (Scsi_device)
and should be lowercase (scsi_device).  Fixed by this commit.
Signed-off-by: John Pittman <jpittman@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

In code blocks, :c:func:`...` annotations don't result in
cross-references. Instead, they are rendered verbatim.  Remove these
broken annotations, and mark function calls with parentheses() again.

Fixes: 76d40fae ("genericirq.rst: add cross-reference links and use monospaced fonts")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

This patch fix following warning during 'make xmldocs'

Documentation/driver-api/dmaengine/client.rst:188:
WARNING: Title underline too short.

Further APIs:
------------
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

My bisect scripts starting running into build failures when trying to
compile 4.15-rc1 with the builds failing with things like:

drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:2078: error: Cannot parse struct or union!

The line in question is actually just a #define, but after some digging
it turns out that my scripts pass W=1 and since commit 3a025e1d
("Add optional check for bad kernel-doc comments") that results in
kernel-doc running on each source file. The file in question has a
badly formatted comment immediately before the #define:

/**
 * struct brcmf_skbuff_cb reserves first two bytes in sk_buff::cb for
 * bus layer usage.
 */

which causes the regex in dump_struct to fail (lack of braces following
struct declaration) and kernel-doc returns 1, which causes the build
to fail.

Fix the issue by always returning 0 from kernel-doc when invoked with
-none. It successfully generates no documentation, and prints out any
issues.

Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

Pull NFS client fixes from Anna Schumaker:
 "These patches fix a problem with compiling using an old version of
  gcc, and also fix up error handling in the SUNRPC layer.

   - NFSv4: Ensure gcc 4.4.4 can compile initialiser for
     "invalid_stateid"

   - SUNRPC: Allow connect to return EHOSTUNREACH

   - SUNRPC: Handle ENETDOWN errors"

* tag 'nfs-for-4.15-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  SUNRPC: Handle ENETDOWN errors
  SUNRPC: Allow connect to return EHOSTUNREACH
  NFSv4: Ensure gcc 4.4.4 can compile initialiser for "invalid_stateid"

Pull xfs fixes from Darrick Wong:
 "Here are some bug fixes for 4.15-rc2.

   - fix memory leaks that appeared after removing ifork inline data
     buffer

   - recover deferred rmap update log items in correct order

   - fix memory leaks when buffer construction fails

   - fix memory leaks when bmbt is corrupt

   - fix some uninitialized variables and math problems in the quota
     scrubber

   - add some omitted attribution tags on the log replay commit

   - fix some UBSAN complaints about integer overflows with large sparse
     files

   - implement an effective inode mode check in online fsck

   - fix log's inability to retry quota item writeout due to transient
     errors"

* tag 'xfs-4.15-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: Properly retry failed dquot items in case of error during buffer writeback
  xfs: scrub inode mode properly
  xfs: remove unused parameter from xfs_writepage_map
  xfs: ubsan fixes
  xfs: calculate correct offset in xfs_scrub_quota_item
  xfs: fix uninitialized variable in xfs_scrub_quota
  xfs: fix leaks on corruption errors in xfs_bmap.c
  xfs: fortify xfs_alloc_buftarg error handling
  xfs: log recovery should replay deferred ops in order
  xfs: always free inline data before resetting inode fork during ifree

Merge tag 'riscv-for-linus-4.15-rc2_cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/linux

Pull RISC-V cleanups and ABI fixes from Palmer Dabbelt:
 "This contains a handful of small cleanups that are a result of
  feedback that didn't make it into our original patch set, either
  because the feedback hadn't been given yet, I missed the original
  emails, or we weren't ready to submit the changes yet.

  I've been maintaining the various cleanup patch sets I have as their
  own branches, which I then merged together and signed. Each merge
  commit has a short summary of the changes, and each branch is based on
  your latest tag (4.15-rc1, in this case). If this isn't the right way
  to do this then feel free to suggest something else, but it seems sane
  to me.

  Here's a short summary of the changes, roughly in order of how
  interesting they are.

   - libgcc.h has been moved from include/lib, where it's the only
     member, to include/linux. This is meant to avoid tab completion
     conflicts.

   - VDSO entries for clock_get/gettimeofday/getcpu have been added.
     These are simple syscalls now, but we want to let glibc use them
     from the start so we can make them faster later.

   - A VDSO entry for instruction cache flushing has been added so
     userspace can flush the instruction cache.

   - The VDSO symbol versions for __vdso_cmpxchg{32,64} have been
     removed, as those VDSO entries don't actually exist.

   - __io_writes has been corrected to respect the given type.

   - A new READ_ONCE in arch_spin_is_locked().

   - __test_and_op_bit_ord() is now actually ordered.

   - Various small fixes throughout the tree to enable allmodconfig to
     build cleanly.

   - Removal of some dead code in our atomic support headers.

   - Improvements to various comments in our atomic support headers"

* tag 'riscv-for-linus-4.15-rc2_cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/linux: (23 commits)
  RISC-V: __io_writes should respect the length argument
  move libgcc.h to include/linux
  RISC-V: Clean up an unused include
  RISC-V: Allow userspace to flush the instruction cache
  RISC-V: Flush I$ when making a dirty page executable
  RISC-V: Add missing include
  RISC-V: Use define for get_cycles like other architectures
  RISC-V: Provide stub of setup_profiling_timer()
  RISC-V: Export some expected symbols for modules
  RISC-V: move empty_zero_page definition to C and export it
  RISC-V: io.h: type fixes for warnings
  RISC-V: use RISCV_{INT,SHORT} instead of {INT,SHORT} for asm macros
  RISC-V: use generic serial.h
  RISC-V: remove spin_unlock_wait()
  RISC-V: `sfence.vma` orderes the instruction cache
  RISC-V: Add READ_ONCE in arch_spin_is_locked()
  RISC-V: __test_and_op_bit_ord should be strongly ordered
  RISC-V: Remove smb_mb__{before,after}_spinlock()
  RISC-V: Remove __smp_bp__{before,after}_atomic
  RISC-V: Comment on why {,cmp}xchg is ordered how it is
  ...