Only use the TROCR register on R-Car Gen3 as it is not present on other
SoCs.

Offsets used for the undocumented registers are considered reserved and
should not be written to. After some internal investigation with Renesas it
remains unclear why this driver accesses these fields on R-Car Gen2 but
regardless of what the historical reasons are the current code is
considered incorrect.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes the use of the undocumented BOC bit of the CCC register.

Current documentation for EtherAVB (ravb) describes the offset of what the
driver uses as the BOC bit as reserved and that only a value of 0 should be
written. After some internal investigation with Renesas it remains unclear
why this driver accesses these fields but regardless of what the historical
reasons are the current code is considered incorrect.

Based on work by Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes the use of the undocumented counter registers
CDCR, LCCR, CERCR, CEECR.

Offsets used for undocumented registers are considered reserved and
should not be written to. After some internal investigation with Renesas
it remains unclear why this driver accesses these fields but regardless of
what the historical reasons are the current code is considered incorrect.

Based on work by Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The field name is FBP rather than FPB.

This field is unused and could equally be removed from the driver entirely.
But there seems no harm in leaving as documentation of the presence of the
field.

Based on work by Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: add some bugfixes and cleanups

This patch-set includes bugfixes and cleanups for the HNS3
ethernet controller driver.

[patch 01/07] fixes an error when setting VLAN offload.

[patch 02/07] fixes an double free issue when setting ringparam.

[patch 03/07] fixes a mis-assignment of hdev->reset_level.

[patch 04/07] adds a checking for client's validity.

[patch 05/07] simplifies bool variable's assignment.

[patch 06/07] disables loopback when initializing.

[patch 07/07] makes internal function to static.

Change log:
V1->V2: fixes comment from Sergei Shtylyov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

hclge_dbg_get_m7_info is used only in the hclge_debugfs.c,
so it should be declared with static.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the selftest and reset are performed at the same time, the loopback
setting may be still in the enable state after the reset. As a result,
packets cannot be sent out.

This patch fixes this issue by disabling loopback in hclge_mac_init.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Relational and logical operators evaluate to bool,
explicit conversion is overly verbose and unnecessary.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HNS3 driver can only unregister client which included in hnae3_client_list.
This patch adds the client node validity judgment.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since hclge_get_reset_level may return HNAE3_NONE_RESET,
so hdev->reset_level can not be assigned with the return
value in the hclge_reset(), otherwise, it will cause
the use of hdev->reset_level in hclge_reset_event get
into error.

Fixes: 012fcb52 ("net: hns3: activate reset timer when calling reset_event")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The system will panic when change the ringparam in HNS3 drivers:

[ 1459.627727] hns3 0000:bd:00.0 eth6: Changing Tx/Rx ring ds from 1024/1024 to 24/24
[ 1459.635766] hns3 0000:bd:00.0 eth6: link down
[ 1459.640788] BUG: Bad page state in process ethtool  pfn:203f75c18
[ 1459.646940] page:ffff7ee4ffd70600 refcount:0 mapcount:0 mapping:ffff993fff40f400 index:0x0 compound_mapcount: 0
[ 1459.656987] flags: 0x9fffe00000010200(slab|head)
[ 1459.661591] raw: 9fffe00000010200 dead000000000100 dead000000000122 ffff993fff40f400
[ 1459.669302] raw: 0000000000000000 0000000080100010 00000000ffffffff 0000000000000000
[ 1459.677016] page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set
[ 1459.683432] bad because of flags: 0x200(slab)
[ 1459.687775] Modules linked in: ib_ipoib ib_umad rpcrdma ib_iser libiscsi scsi_transport_iscsi hns_roce_hw_v2 crct10dif_ce hns3 ses hclge hnae3 hisi_hpre hisi_zip qm uacce ip_tables x_tables hisi_sas_v3_hw hisi_sas_main libsas scsi_transport_sas
[ 1459.709329] CPU: 14 PID: 17244 Comm: ethtool Tainted: G           O      5.3.0-rc4-00415-gc86f057 #1
[ 1459.718419] Hardware name: Huawei TaiShan 2280 V2/BC82AMDC, BIOS 2280-V2 CS V3.B040.01 07/26/2019
[ 1459.727248] Call trace:
[ 1459.729688]  dump_backtrace+0x0/0x150
[ 1459.733335]  show_stack+0x24/0x30
[ 1459.736639]  dump_stack+0xa0/0xc4
[ 1459.739943]  bad_page+0xf0/0x158
[ 1459.743157]  free_pages_check_bad+0x84/0xa0
[ 1459.747322]  __free_pages_ok+0x348/0x378
[ 1459.751228]  page_frag_free+0x80/0x88
[ 1459.754877]  skb_free_head+0x38/0x48
[ 1459.758436]  skb_release_data+0x134/0x160
[ 1459.762427]  skb_release_all+0x30/0x40
[ 1459.766158]  consume_skb+0x38/0x108
[ 1459.769633]  __dev_kfree_skb_any+0x58/0x68
[ 1459.773718]  hns3_fini_ring+0x48/0x58 [hns3]
[ 1459.777970]  hns3_set_ringparam+0x2a8/0x418 [hns3]
[ 1459.782741]  dev_ethtool+0x5f4/0x2080
[ 1459.786390]  dev_ioctl+0x190/0x3d8
[ 1459.789777]  sock_do_ioctl+0xf8/0x220
[ 1459.793423]  sock_ioctl+0x3bc/0x490
[ 1459.796896]  do_vfs_ioctl+0xc4/0x868
[ 1459.800454]  ksys_ioctl+0x8c/0xa0
[ 1459.803752]  __arm64_sys_ioctl+0x28/0x38
[ 1459.807658]  el0_svc_common.constprop.0+0xe0/0x1e0
[ 1459.812426]  el0_svc_handler+0x34/0x90
[ 1459.816158]  el0_svc+0x10/0x14
[ 1459.819220] Disabling lock debugging due to kernel taint
[ 1459.825182] ------------[ cut here ]------------

Since ndo_stop will reclaim the RX's skb allocated by the driver,
so the backed up ring parameter should not keep this info.

Fixes: a723fb8e ("net: hns3: refine for set ring parameters")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In original codes, the VF index used incorrectly in function
hclge_set_vlan_rx_offload_cfg() and hclge_set_vlan_rx_offload_cfg().
When VF id is greater than 8, for example 9, it will set the
same bit with VF id 1.

This patch fixes it by using  vport->vport_id % HCLGE_VF_NUM_PER_CMD /
HCLGE_VF_NUM_PER_BYTE as the array index, instead of vport->vport_id /
HCLGE_VF_NUM_PER_CMD.

Fixes: 052ece6d ("net: hns3: add ethtool related offload command")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch amends the error and warning messages across the platform driver.
It includes the following changes:
 - append \n to the end of messages
 - change pr_* macros to dev_*
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While running stmmac selftests I found that in my 1G setup some tests
were failling when running with PHY loopback enabled.

It looks like when loopback is enabled the PHY will report that Link is
down even though there is a valid connection.

As in loopback mode the data will not be sent anywhere we can bypass the
logic of checking if Link is valid thus saving unecessary reads.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For high speed adapter like Mellanox CX-5 card, it can reach upto
100 Gbits per second bandwidth. Currently htb already supports 64bit rate
in tc utility. However police action rate and peakrate are still limited
to 32bit value (upto 32 Gbits per second). Add 2 new attributes
TCA_POLICE_RATE64 and TCA_POLICE_RATE64 in kernel for 64bit support
so that tc utility can use them for 64bit rate and peakrate value to
break the 32bit limit, and still keep the backward binary compatibility.
Tested-by: David Dai <zdai@linux.vnet.ibm.com>
Signed-off-by: David Dai <zdai@linux.vnet.ibm.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Offloaded OvS datapath rules are translated one to one to tc rules,
for example the following simplified OvS rule:

recirc_id(0),in_port(dev1),eth_type(0x0800),ct_state(-trk) actions:ct(),recirc(2)

Will be translated to the following tc rule:

$ tc filter add dev dev1 ingress \
	    prio 1 chain 0 proto ip \
		flower tcp ct_state -trk \
		action ct pipe \
		action goto chain 2

Received packets will first travel though tc, and if they aren't stolen
by it, like in the above rule, they will continue to OvS datapath.
Since we already did some actions (action ct in this case) which might
modify the packets, and updated action stats, we would like to continue
the proccessing with the correct recirc_id in OvS (here recirc_id(2))
where we left off.

To support this, introduce a new skb extension for tc, which
will be used for translating tc chain to ovs recirc_id to
handle these miss cases. Last tc chain index will be set
by tc goto chain action and read by OvS datapath.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Continue is not needed at the bottom of a loop.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The UPS feature only works for runtime suspend, so UPS flags only
need to be set before enabling runtime suspend. Therefore, I create
a struct to record relative information, and use it before runtime
suspend.

All chips could record such information, even though not all of
them support the feature of UPS. Then, some functions could be
combined.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the static keyword to the front of declaration of g_dsaf_mode_match,
and resolve the following compiler warning that can be seen when building
with warnings enabled (W=1):

drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:27:1: warning:
  ‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the static keyword to the front of declaration of iwarp_state_names,
and resolve the following compiler warning that can be seen when building
with warnings enabled (W=1):

drivers/net/ethernet/qlogic/qed/qed_iwarp.c:385:1: warning:
  ‘static’ is not at beginning of declaration [-Wold-style-declaration]

Also, resolve checkpatch.pl script warning:

WARNING: static const char * array should probably be
  static const char * const
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use %*ph format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Harini Katakam says:

====================
Fix GMII2RGMII private field

Fix the usage of external phy's priv field by gmii2rgmii driver.

Based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use set/get drv data in phydev's mdio device instead. Phy device priv
field maybe used by the external phy driver and should not be
overwritten.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add set/get drv_data helpers for mdio device.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Arseny Solokha says:

====================
gianfar: some assorted cleanup

This is a cleanup series for the gianfar Ethernet driver, following up a
discussion in [1]. It is intended to precede a conversion of gianfar from
PHYLIB to PHYLINK API, which will be submitted later in its version 2.
However, it won't make a conversion cleaner, except for the last patch in
this series. Obviously this series is not intended for -stable.

The first patch looks super controversial to me, as it moves lots of code
around for the sole purpose of getting rid of static forward declarations
in two translation units. On the other hand, this change is purely
mechanical and cannot do any harm other than cluttering git blame output.
I can prepare an alternative patch for only swapping adjacent functions
around, if necessary.

The second patch is a trivial follow-up to the first one, making functions
that are only called from the same translation unit static.

The third patch removes some now unused macro and structure definitions
from gianfar.h, slipped away from various cleanups in the past.

The fourth patch, also suggested in [1], makes the driver consistently use
PHY connection type value obtained from a Device Tree node, instead of
ignoring it and using the one auto-detected by MAC, when connecting to PHY.
Obviously a value has to be specified correctly in DT source, or omitted
altogether, in which case the driver will fall back to auto-detection. When
querying a DT node, the driver will also take both applicable properties
into account by making a proper API call instead of open-coding the lookup
half-way correctly.

[1] https://lore.kernel.org/netdev/CA+h21hruqt6nGG5ksDSwrGH_w5GtGF4fjAMCWJne7QJrjusERQ@mail.gmail.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Historically, gianfar only used phy-connection-type DT property when
connected to PHY in the rgmii-id mode. It ignored the property otherwise,
relying on the connection type auto-detection carried out by MAC and
providing that reconstructed mode to of_phy_connect(). It also did not
consider alternative phy-mode property at all.

Make the driver properly query DT node for PHY connection type first and
use an obtained value if it was specified there. Otherwise, if a particular
DT relies on connection type auto-detection, fall back to reconstructing
the value from MAC registers, as before.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove now unused macro and structure definitions from gianfar.h that have
accumulated there over time.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make functions that do not have callers outside the translation unit they
are defined in static.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove forward declarations of various static functions located in two
driver implementation files and rearrange the corresponding definitions
accordingly.

This patch only introduces mechanical changes, namely it removes forward
declarations and moves function definitions around; it does not change any
functionality.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jose Abreu says:

====================
net: stmmac: Improvements for -next

Couple of improvements for -next tree. More info in commit logs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test to validate the Jumbo Frame support in stmmac in single
channel and multichannel mode.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are already doing it by default in the TX path so we can also enable
Jumbo Frame support in the RX path independently of MTU value.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Maximum MTU for XGMAC cores is 16k thus the check for presence of XGMAC
shall be done first in order to assign correct value.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RAVSEL means that only RX side is available for AVB features. As we use
both TX and RX features we need to check if RAVSEL is selected and
disable AVB if only RX side is available.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When RX Watchdog is disabled its currently not possible to configure TX
coalesce settings. Let user configure it anyway.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only consider that we have an error when HW Timestamping is not enabled
as this can give false positives due to the fact the RX Timestamping in
XGMAC and GMAC cores comes from context descriptors.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement a test for ARP Offload feature.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the ARP Offload feature in XGMAC cores.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds the selftests for L3 and L4 filters with DA/SA/DP/SP support.

Changes from v1:
	- Reduce stack usage (kbuild test robot)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement filters for Layer 3 and Layer 4 using TC Flower API. Add the
corresponding callbacks in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>