Pull drm fixes from Dave Airlie:
 "This is the weekly fixes for rc4. Misc fixes across rockchip, imx,
  amdgpu and i915.

  The biggest change is for amdkfd where the trap handler needs an
  updated fw from a header which makes it a bit larger. I hadn't noticed
  this particular file before so I'm going to figure out what the magic
  is for, but the fix should be fine for now.

  amdgpu:
   - DCN 3.1.4 fixes
   - DCN 3.2.x fixes
   - GC 11.x fixes
   - Virtual display fix
   - Fail suspend if resources can't be evicted
   - SR-IOV fix
   - Display PSR fix

  amdkfd:
   - Fix possible NULL pointer deref
   - GC 11.x trap handler fix

  i915:
   - Add locking around DKL PHY register accesses
   - Stop abusing swiotlb_max_segment
   - Filter out invalid outputs more sensibly
   - Setup DDC fully before output init
   - Simplify intel_panel_add_edid_alt_fixed_modes()
   - Grab mode_config.mutex during LVDS init to avoid WARNs

  rockchip:
   - fix probing issues
   - fix framebuffer without iommu
   - fix vop selection
   - fix NULL ptr access

  imx:
   - Fix Kconfig
   - fix mode_valid function"

* tag 'drm-fixes-2022-11-04-1' of git://anongit.freedesktop.org/drm/drm: (35 commits)
  drm/amdkfd: update GFX11 CWSR trap handler
  drm/amd/display: Investigate tool reported FCLK P-state deviations
  drm/amd/display: Add DSC delay factor workaround
  drm/amd/display: Round up DST_after_scaler to nearest int
  drm/amd/display: Use forced DSC bpp in DML
  drm/amd/display: Fix DCN32 DSC delay calculation
  drm/amdgpu: Disable GPU reset on SRIOV before remove pci.
  drm/amdgpu: disable GFXOFF during compute for GFX11
  drm/amd: Fail the suspend if resources can't be evicted
  drm/amdkfd: Fix NULL pointer dereference in svm_migrate_to_ram()
  drm/amdgpu: correct MES debugfs versions
  drm/amdgpu: set fb_modifiers_not_supported in vkms
  drm/amd/display: cursor update command incomplete
  drm/amd/display: Enable timing sync on DCN32
  drm/amd/display: Set memclk levels to be at least 1 for dcn32
  drm/amd/display: Update latencies on DCN321
  drm/amd/display: Limit dcn32 to 1950Mhz display clock
  drm/amd/display: Ignore Cable ID Feature
  drm/amd/display: Update DSC capabilitie for DCN314
  drm/imx: imx-tve: Fix return type of imx_tve_connector_mode_valid
  ...

Pull clk fixes from Stephen Boyd:
 "Fixes in clk drivers and some clk rate range fixes in the core as
  well:

   - Make sure the struct clk_rate_request is more sane

   - Remove a WARN_ON that was triggering for clks with no parents that
     can change frequency

   - Fix bad i2c bus transactions on Renesas rs9

   - Actually return an error in clk_mt8195_topck_probe() on an error
     path

   - Keep the GPU memories powered while the clk isn't enabled on
     Qualcomm's sc7280 SoC

   - Fix the parent clk for HSCIF modules on Renesas' R-Car V4H SoC"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: qcom: Update the force mem core bit for GPU clocks
  clk: Initialize max_rate in struct clk_rate_request
  clk: Initialize the clk_rate_request even if clk_core is NULL
  clk: Remove WARN_ON NULL parent in clk_core_init_rate_req()
  clk: renesas: r8a779g0: Fix HSCIF parent clocks
  clk: renesas: r8a779g0: Add SASYNCPER clocks
  clk: mediatek: clk-mt8195-topckgen: Fix error return code in clk_mt8195_topck_probe()
  clk: sifive: select by default if SOC_SIFIVE
  clk: rs9: Fix I2C accessors

Pull ata fixes from Damien Le Moal:
 "Two driver fixes:

   - Fix the PIO mode configuration of the pdc20230 (pata_legacy)
     driver. This also removes a compilation warning with clang and W=1
     (Sergey)

   - Fix devm_platform_ioremap_resource() return value check in the
     palmld driver (Yang)"

* tag 'ata-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
  ata: palmld: fix return value check in palmld_pata_probe()
  ata: pata_legacy: fix pdc20230_set_piomode()

Merge tag 'drm-intel-fixes-2022-11-03' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

- Add locking around DKL PHY register accesses (Imre Deak)
- Stop abusing swiotlb_max_segment (Robert Beckett)
- Filter out invalid outputs more sensibly (Ville Syrjälä)
- Setup DDC fully before output init (Ville Syrjälä)
- Simplify intel_panel_add_edid_alt_fixed_modes() (Ville Syrjälä)
- Grab mode_config.mutex during LVDS init to avoid WARNs (Ville Syrjälä)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Y2ODlCGM4nACmzsJ@tursulin-desk

Merge tag 'amd-drm-fixes-6.1-2022-11-02' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes

amd-drm-fixes-6.1-2022-11-02:

amdgpu:
- DCN 3.1.4 fixes
- DCN 3.2.x fixes
- GC 11.x fixes
- Virtual display fix
- Fail suspend if resources can't be evicted
- SR-IOV fix
- Display PSR fix

amdkfd:
- Fix possible NULL pointer deref
- GC 11.x trap handler fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221103023257.10446-1-alexander.deucher@amd.com

Pull fuse fixes from Miklos Szeredi:
 "Fix two rarely triggered but long-standing issues"

* tag 'fuse-fixes-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: add file_modified() to fallocate
  fuse: fix readdir cache race

Pull btrfs fixes from David Sterba:
 "A batch of error handling fixes for resource leaks, fixes for nowait
  mode in combination with direct and buffered IO:

   - direct IO + dsync + nowait could miss a sync of the file after
     write, add handling for this combination

   - buffered IO + nowait should not fail with ENOSPC, only blocking IO
     could determine that

   - error handling fixes:
      - fix inode reserve space leak due to nowait buffered write
      - check the correct variable after allocation (direct IO submit)
      - fix inode list leak during backref walking
      - fix ulist freeing in self tests"

* tag 'for-6.1-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: fix inode reserve space leak due to nowait buffered write
  btrfs: fix nowait buffered write returning -ENOSPC
  btrfs: remove pointless and double ulist frees in error paths of qgroup tests
  btrfs: fix ulist leaks in error paths of qgroup self tests
  btrfs: fix inode list leak during backref walking at find_parent_nodes()
  btrfs: fix inode list leak during backref walking at resolve_indirect_refs()
  btrfs: fix lost file sync on direct IO write with nowait and dsync iocb
  btrfs: fix a memory allocation failure test in btrfs_submit_direct

Merge tag 'linux-kselftest-fixes-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fixes from Shuah Khan:
 "Fixes to the pidfd test"

* tag 'linux-kselftest-fixes-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests/pidfd_test: Remove the erroneous ','
  selftests: pidfd: Fix compling warnings
  ksefltests: pidfd: Fix wait_states: Test terminated by timeout

Pull networking fixes from Paolo Abeni:
 "Including fixes from bluetooth and netfilter.

  Current release - regressions:

   - net: several zerocopy flags fixes

   - netfilter: fix possible memory leak in nf_nat_init()

   - openvswitch: add missing .resv_start_op

  Previous releases - regressions:

   - neigh: fix null-ptr-deref in neigh_table_clear()

   - sched: fix use after free in red_enqueue()

   - dsa: fall back to default tagger if we can't load the one from DT

   - bluetooth: fix use-after-free in l2cap_conn_del()

  Previous releases - always broken:

   - netfilter: netlink notifier might race to release objects

   - nfc: fix potential memory leak of skb

   - bluetooth: fix use-after-free caused by l2cap_reassemble_sdu

   - bluetooth: use skb_put to set length

   - eth: tun: fix bugs for oversize packet when napi frags enabled

   - eth: lan966x: fixes for when MTU is changed

   - eth: dwmac-loongson: fix invalid mdio_node"

* tag 'net-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (53 commits)
  vsock: fix possible infinite sleep in vsock_connectible_wait_data()
  vsock: remove the unused 'wait' in vsock_connectible_recvmsg()
  ipv6: fix WARNING in ip6_route_net_exit_late()
  bridge: Fix flushing of dynamic FDB entries
  net, neigh: Fix null-ptr-deref in neigh_table_clear()
  net/smc: Fix possible leaked pernet namespace in smc_init()
  stmmac: dwmac-loongson: fix invalid mdio_node
  ibmvnic: Free rwi on reset success
  net: mdio: fix undefined behavior in bit shift for __mdiobus_register
  Bluetooth: L2CAP: Fix attempting to access uninitialized memory
  Bluetooth: L2CAP: Fix l2cap_global_chan_by_psm
  Bluetooth: L2CAP: Fix accepting connection request for invalid SPSM
  Bluetooth: hci_conn: Fix not restoring ISO buffer count on disconnect
  Bluetooth: L2CAP: Fix memory leak in vhci_write
  Bluetooth: L2CAP: fix use-after-free in l2cap_conn_del()
  Bluetooth: virtio_bt: Use skb_put to set length
  Bluetooth: hci_conn: Fix CIS connection dst_type handling
  Bluetooth: L2CAP: Fix use-after-free caused by l2cap_reassemble_sdu
  netfilter: ipset: enforce documented limit to prevent allocating huge memory
  isdn: mISDN: netjet: fix wrong check of device registration
  ...

Pull powerpc fixes from Michael Ellerman:

 - Fix an endian thinko in the asm-generic compat_arg_u64() which led to
   syscall arguments being swapped for some compat syscalls.

 - Fix syscall wrapper handling of syscalls with 64-bit arguments on
   32-bit kernels, which led to syscall arguments being misplaced.

 - A build fix for amdgpu on Book3E with AltiVec disabled.

Thanks to Andreas Schwab, Christian Zigotzky, and Arnd Bergmann.

* tag 'powerpc-6.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/32: Select ARCH_SPLIT_ARG64
  powerpc/32: fix syscall wrappers with 64-bit arguments
  asm-generic: compat: fix compat_arg_u64() and compat_arg_u64_dual()
  powerpc/64e: Fix amdgpu build on Book3E w/o AltiVec

Dexuan Cui says:

====================
vsock: remove an unused variable and fix infinite sleep

Patch 1 removes the unused 'wait' variable.
Patch 2 fixes an infinite sleep issue reported by a hv_sock user.
====================

Link: https://lore.kernel.org/r/20221101021706.26152-1-decui@microsoft.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Currently vsock_connectible_has_data() may miss a wakeup operation
between vsock_connectible_has_data() == 0 and the prepare_to_wait().

Fix the race by adding the process to the wait queue before checking
vsock_connectible_has_data().

Fixes: b3f7fd54 ("af_vsock: separate wait data loop")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reported-by: Frédéric Dalleau <frederic.dalleau@docker.com>
Tested-by: Frédéric Dalleau <frederic.dalleau@docker.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Remove the unused variable introduced by 19c1b90e.

Fixes: 19c1b90e ("af_vsock: separate receive data loop")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Merge tag 'drm-misc-fixes-2022-11-02-1' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes

drm-misc-fixes for v6.1-rc4:
- Small fixes to make rockchip work better.
- Fix imx Kconfig.
- Small fix to imx' mode_valid.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5476ef52-f91a-c2bc-f4b2-d338216d1e11@linux.intel.com

During the initialization of ip6_route_net_init_late(), if file
ipv6_route or rt6_stats fails to be created, the initialization is
successful by default. Therefore, the ipv6_route or rt6_stats file
doesn't be found during the remove in ip6_route_net_exit_late(). It
will cause WRNING.

The following is the stack information:
name 'rt6_stats'
WARNING: CPU: 0 PID: 9 at fs/proc/generic.c:712 remove_proc_entry+0x389/0x460
Modules linked in:
Workqueue: netns cleanup_net
RIP: 0010:remove_proc_entry+0x389/0x460
PKRU: 55555554
Call Trace:
<TASK>
ops_exit_list+0xb0/0x170
cleanup_net+0x4ea/0xb00
process_one_work+0x9bf/0x1710
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
</TASK>

Fixes: cdb18761 ("[NETNS][IPV6] route6 - create route6 proc files for the namespace")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221102020610.351330-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The following commands should result in all the dynamic FDB entries
being flushed, but instead all the non-local (non-permanent) entries are
flushed:

 # bridge fdb add 00:aa:bb:cc:dd:ee dev dummy1 master static
 # bridge fdb add 00:11:22:33:44:55 dev dummy1 master dynamic
 # ip link set dev br0 type bridge fdb_flush
 # bridge fdb show brport dummy1
 00:00:00:00:00:01 master br0 permanent
 33:33:00:00:00:01 self permanent
 01:00:5e:00:00:01 self permanent

This is because br_fdb_flush() works with FDB flags and not the
corresponding enumerator values. Fix by passing the FDB flag instead.

After the fix:

 # bridge fdb add 00:aa:bb:cc:dd:ee dev dummy1 master static
 # bridge fdb add 00:11:22:33:44:55 dev dummy1 master dynamic
 # ip link set dev br0 type bridge fdb_flush
 # bridge fdb show brport dummy1
 00:aa:bb:cc:dd:ee master br0 static
 00:00:00:00:00:01 master br0 permanent
 33:33:00:00:00:01 self permanent
 01:00:5e:00:00:01 self permanent

Fixes: 1f78ee14 ("net: bridge: fdb: add support for fine-grained flushing")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20221101185753.2120691-1-idosch@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When IPv6 module gets initialized but hits an error in the middle,
kenel panic with:

KASAN: null-ptr-deref in range [0x0000000000000598-0x000000000000059f]
CPU: 1 PID: 361 Comm: insmod
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
RIP: 0010:__neigh_ifdown.isra.0+0x24b/0x370
RSP: 0018:ffff888012677908 EFLAGS: 00000202
...
Call Trace:
 <TASK>
 neigh_table_clear+0x94/0x2d0
 ndisc_cleanup+0x27/0x40 [ipv6]
 inet6_init+0x21c/0x2cb [ipv6]
 do_one_initcall+0xd3/0x4d0
 do_init_module+0x1ae/0x670
...
Kernel panic - not syncing: Fatal exception

When ipv6 initialization fails, it will try to cleanup and calls:

neigh_table_clear()
  neigh_ifdown(tbl, NULL)
    pneigh_queue_purge(&tbl->proxy_queue, dev_net(dev == NULL))
    # dev_net(NULL) triggers null-ptr-deref.

Fix it by passing NULL to pneigh_queue_purge() in neigh_ifdown() if dev
is NULL, to make kernel not panic immediately.

Fixes: 66ba215c ("neigh: fix possible DoS due to net iface start/stop loop")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Denis V. Lunev <den@openvz.org>
Link: https://lore.kernel.org/r/20221101121552.21890-1-chenzhongjin@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In smc_init(), register_pernet_subsys(&smc_net_stat_ops) is called
without any error handling.
If it fails, registering of &smc_net_ops won't be reverted.
And if smc_nl_init() fails, &smc_net_stat_ops itself won't be reverted.

This leaves wild ops in subsystem linkedlist and when another module
tries to call register_pernet_operations() it triggers page fault:

BUG: unable to handle page fault for address: fffffbfff81b964c
RIP: 0010:register_pernet_operations+0x1b9/0x5f0
Call Trace:
  <TASK>
  register_pernet_subsys+0x29/0x40
  ebtables_init+0x58/0x1000 [ebtables]
  ...

Fixes: 194730a9 ("net/smc: Make SMC statistics network namespace aware")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Link: https://lore.kernel.org/r/20221101093722.127223-1-chenzhongjin@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In current code "plat->mdio_node" is always NULL, the mdio
support is lost as there is no "mdio_bus_data". The original
driver could work as the "mdio" variable is never set to
false, which is described in commit <b0e03950> ("stmmac:
dwmac-loongson: fix uninitialized variable ......"). And
after this commit merged, the "mdio" variable is always
false, causing the mdio supoort logic lost.

Fixes: 30bba69d ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Liu Peibao <liupeibao@loongson.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221101060218.16453-1-liupeibao@loongson.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Free the rwi structure in the event that the last rwi in the list
processed successfully. The logic in commit 4f408e1f ("ibmvnic:
retry reset if there are no other resets") introduces an issue that
results in a 32 byte memory leak whenever the last rwi in the list
gets processed.

Fixes: 4f408e1f ("ibmvnic: retry reset if there are no other resets")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Link: https://lore.kernel.org/r/20221031150642.13356-1-nnac123@linux.ibm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:

UBSAN: shift-out-of-bounds in drivers/net/phy/mdio_bus.c:586:27
left shift of 1 by 31 places cannot be represented in type 'int'
Call Trace:
 <TASK>
 dump_stack_lvl+0x7d/0xa5
 dump_stack+0x15/0x1b
 ubsan_epilogue+0xe/0x4e
 __ubsan_handle_shift_out_of_bounds+0x1e7/0x20c
 __mdiobus_register+0x49d/0x4e0
 fixed_mdio_bus_init+0xd8/0x12d
 do_one_initcall+0x76/0x430
 kernel_init_freeable+0x3b3/0x422
 kernel_init+0x24/0x1e0
 ret_from_fork+0x1f/0x30
 </TASK>

Fixes: 4fd5f812 ("phylib: allow incremental scanning of an mii bus")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221031132645.168421-1-cuigaosheng1@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS fixes for net

1) netlink socket notifier might win race to release objects that are
   already pending to be released via commit release path, reported by
   syzbot.

2) No need to postpone flow rule release to commit release path, this
   triggered the syzbot report, complementary fix to previous patch.

3) Use explicit signed chars in IPVS to unbreak arm, from Jason A. Donenfeld.

4) Missing check for proc entry creation failure in IPVS, from Zhengchao Shao.

5) Incorrect error path handling when BPF NAT fails to register, from
   Chen Zhongjin.

6) Prevent huge memory allocation in ipset hash types, from Jozsef Kadlecsik.

Except the incorrect BPF NAT error path which is broken in 6.1-rc, anything
else has been broken for several releases.

* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
  netfilter: ipset: enforce documented limit to prevent allocating huge memory
  netfilter: nf_nat: Fix possible memory leak in nf_nat_init()
  ipvs: fix WARNING in ip_vs_app_net_cleanup()
  ipvs: fix WARNING in __ip_vs_cleanup_batch()
  ipvs: use explicitly signed chars
  netfilter: nf_tables: release flow rule object from commit path
  netfilter: nf_tables: netlink notifier might race to release objects
====================

Link: https://lore.kernel.org/r/20221102184659.2502-1-pablo@netfilter.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Luiz Augusto von Dentz says:

====================
bluetooth 2022-11-02

 - Fix memory leak in hci_vhci driver
 - Fix handling of skb on virtio_bt driver
 - Fix accepting connection for invalid L2CAP PSM
 - Fix attemting to access uninitialized memory
 - Fix use-after-free in l2cap_reassemble_sdu
 - Fix use-after-free in l2cap_conn_del
 - Fix handling of destination address type for CIS
 - Fix not restoring ISO buffer count on disconnect

* tag 'for-net-2022-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
  Bluetooth: L2CAP: Fix attempting to access uninitialized memory
  Bluetooth: L2CAP: Fix l2cap_global_chan_by_psm
  Bluetooth: L2CAP: Fix accepting connection request for invalid SPSM
  Bluetooth: hci_conn: Fix not restoring ISO buffer count on disconnect
  Bluetooth: L2CAP: Fix memory leak in vhci_write
  Bluetooth: L2CAP: fix use-after-free in l2cap_conn_del()
  Bluetooth: virtio_bt: Use skb_put to set length
  Bluetooth: hci_conn: Fix CIS connection dst_type handling
  Bluetooth: L2CAP: Fix use-after-free caused by l2cap_reassemble_sdu
====================

Link: https://lore.kernel.org/r/20221102235927.3324891-1-luiz.dentz@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

On l2cap_parse_conf_req the variable efs is only initialized if
remote_efs has been set.

CVE: CVE-2022-42895
CC: stable@vger.kernel.org
Reported-by: Tamás Koczka <poprdi@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Tedd Ho-Jeong An <tedd.an@intel.com>

l2cap_global_chan_by_psm shall not return fixed channels as they are not
meant to be connected by (S)PSM.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Tedd Ho-Jeong An <tedd.an@intel.com>

The Bluetooth spec states that the valid range for SPSM is from
0x0001-0x00ff so it is invalid to accept values outside of this range:

  BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 3, Part A
  page 1059:
  Table 4.15: L2CAP_LE_CREDIT_BASED_CONNECTION_REQ SPSM ranges

CVE: CVE-2022-42896
CC: stable@vger.kernel.org
Reported-by: Tamás Koczka <poprdi@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Tedd Ho-Jeong An <tedd.an@intel.com>

With corresponding FW change fixes issue where triggering CWSR on a
workgroup with waves in s_barrier wouldn't lead to a back-off and
therefore cause a hang.
Signed-off-by: Jay Cornwall <jay.cornwall@amd.com>
Tested-by: Graham Sider <Graham.Sider@amd.com>
Acked-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Graham Sider <Graham.Sider@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x

[Why]
Fix for some of the tool reported modes for FCLK
P-state deviations and UCLK P-state deviations that
are coming from DSC terms and/or Scaling terms
causing MinActiveFCLKChangeLatencySupported
and MaxActiveDRAMClockChangeLatencySupported
incorrectly calculated in DML for these configurations.
Reviewed-by: Chaitanya Dhere <Chaitanya.Dhere@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Certain 4K high refresh rate modes requiring DSC are exhibiting top
of screen underflow corruption. Increasing the DSC delay by a factor
of 6 percent stops the underflow for most use cases.

[How]
Multiply DSC delay requirement in DML by a factor.
Add debug option to make this DSC delay factor configurable.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
The DST_after_scaler value that DML spreadsheet outputs is
generally the driver value round up to the nearest int.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DSC config is calculated separately from DML calculations.
DML should use these separately calculated DSC params. The issue is
that the calculated bpp is not properly propagated into DML.

[How]
Correctly used forced_bpp value in DML.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DCN32 DSC delay calculation had an unintentional integer division,
resulting in a mismatch against the DML spreadsheet.

[How]
Cast numerator to double before performing the division.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The recent change brought a bug on SRIOV envrionment. It caused
unloading amdgpu failed on Guest VM. The reason is that the VF
FLR was requested while unloading amdgpu driver, but the VF FLR
of SRIOV sequence is wrong while removing PCI device.

For SRIOV, the guest driver should not trigger the whole XGMI hive
to do the reset. Host driver control how the device been reset.

Fixes: f5c7e779 ("drm/amdgpu: Adjust removal control flow for smu v13_0_2")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Gavin Wan <Gavin.Wan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Temporary workaround to fix issues observed in some compute applications
when GFXOFF is enabled on GFX11.
Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x

When disconnecting an ISO link the controller may not generate
HCI_EV_NUM_COMP_PKTS for unacked packets which needs to be restored in
hci_conn_del otherwise the host would assume they are still in use and
would not be able to use all the buffers available.

Fixes: 26afbd82 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Frédéric Danis <frederic.danis@collabora.com>

Syzkaller reports a memory leak as follows:
====================================
BUG: memory leak
unreferenced object 0xffff88810d81ac00 (size 240):
  [...]
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff838733d9>] __alloc_skb+0x1f9/0x270 net/core/skbuff.c:418
    [<ffffffff833f742f>] alloc_skb include/linux/skbuff.h:1257 [inline]
    [<ffffffff833f742f>] bt_skb_alloc include/net/bluetooth/bluetooth.h:469 [inline]
    [<ffffffff833f742f>] vhci_get_user drivers/bluetooth/hci_vhci.c:391 [inline]
    [<ffffffff833f742f>] vhci_write+0x5f/0x230 drivers/bluetooth/hci_vhci.c:511
    [<ffffffff815e398d>] call_write_iter include/linux/fs.h:2192 [inline]
    [<ffffffff815e398d>] new_sync_write fs/read_write.c:491 [inline]
    [<ffffffff815e398d>] vfs_write+0x42d/0x540 fs/read_write.c:578
    [<ffffffff815e3cdd>] ksys_write+0x9d/0x160 fs/read_write.c:631
    [<ffffffff845e0645>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
    [<ffffffff845e0645>] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
    [<ffffffff84600087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
====================================

HCI core will uses hci_rx_work() to process frame, which is queued to
the hdev->rx_q tail in hci_recv_frame() by HCI driver.

Yet the problem is that, HCI core may not free the skb after handling
ACL data packets. To be more specific, when start fragment does not
contain the L2CAP length, HCI core just copies skb into conn->rx_skb and
finishes frame process in l2cap_recv_acldata(), without freeing the skb,
which triggers the above memory leak.

This patch solves it by releasing the relative skb, after processing
the above case in l2cap_recv_acldata().

Fixes: 4d7ea8ee ("Bluetooth: L2CAP: Fix handling fragmented length")
Link: https://lore.kernel.org/all/0000000000000d0b1905e6aaef64@google.com/
Reported-and-tested-by: syzbot+8f819e36e01022991cfa@syzkaller.appspotmail.com
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

When l2cap_recv_frame() is invoked to receive data, and the cid is
L2CAP_CID_A2MP, if the channel does not exist, it will create a channel.
However, after a channel is created, the hold operation of the channel
is not performed. In this case, the value of channel reference counting
is 1. As a result, after hci_error_reset() is triggered, l2cap_conn_del()
invokes the close hook function of A2MP to release the channel. Then
 l2cap_chan_unlock(chan) will trigger UAF issue.

The process is as follows:
Receive data:
l2cap_data_channel()
    a2mp_channel_create()  --->channel ref is 2
    l2cap_chan_put()       --->channel ref is 1

Triger event:
    hci_error_reset()
        hci_dev_do_close()
        ...
        l2cap_disconn_cfm()
            l2cap_conn_del()
                l2cap_chan_hold()    --->channel ref is 2
                l2cap_chan_del()     --->channel ref is 1
                a2mp_chan_close_cb() --->channel ref is 0, release channel
                l2cap_chan_unlock()  --->UAF of channel

The detailed Call Trace is as follows:
BUG: KASAN: use-after-free in __mutex_unlock_slowpath+0xa6/0x5e0
Read of size 8 at addr ffff8880160664b8 by task kworker/u11:1/7593
Workqueue: hci0 hci_error_reset
Call Trace:
 <TASK>
 dump_stack_lvl+0xcd/0x134
 print_report.cold+0x2ba/0x719
 kasan_report+0xb1/0x1e0
 kasan_check_range+0x140/0x190
 __mutex_unlock_slowpath+0xa6/0x5e0
 l2cap_conn_del+0x404/0x7b0
 l2cap_disconn_cfm+0x8c/0xc0
 hci_conn_hash_flush+0x11f/0x260
 hci_dev_close_sync+0x5f5/0x11f0
 hci_dev_do_close+0x2d/0x70
 hci_error_reset+0x9e/0x140
 process_one_work+0x98a/0x1620
 worker_thread+0x665/0x1080
 kthread+0x2e4/0x3a0
 ret_from_fork+0x1f/0x30
 </TASK>

Allocated by task 7593:
 kasan_save_stack+0x1e/0x40
 __kasan_kmalloc+0xa9/0xd0
 l2cap_chan_create+0x40/0x930
 amp_mgr_create+0x96/0x990
 a2mp_channel_create+0x7d/0x150
 l2cap_recv_frame+0x51b8/0x9a70
 l2cap_recv_acldata+0xaa3/0xc00
 hci_rx_work+0x702/0x1220
 process_one_work+0x98a/0x1620
 worker_thread+0x665/0x1080
 kthread+0x2e4/0x3a0
 ret_from_fork+0x1f/0x30

Freed by task 7593:
 kasan_save_stack+0x1e/0x40
 kasan_set_track+0x21/0x30
 kasan_set_free_info+0x20/0x30
 ____kasan_slab_free+0x167/0x1c0
 slab_free_freelist_hook+0x89/0x1c0
 kfree+0xe2/0x580
 l2cap_chan_put+0x22a/0x2d0
 l2cap_conn_del+0x3fc/0x7b0
 l2cap_disconn_cfm+0x8c/0xc0
 hci_conn_hash_flush+0x11f/0x260
 hci_dev_close_sync+0x5f5/0x11f0
 hci_dev_do_close+0x2d/0x70
 hci_error_reset+0x9e/0x140
 process_one_work+0x98a/0x1620
 worker_thread+0x665/0x1080
 kthread+0x2e4/0x3a0
 ret_from_fork+0x1f/0x30

Last potentially related work creation:
 kasan_save_stack+0x1e/0x40
 __kasan_record_aux_stack+0xbe/0xd0
 call_rcu+0x99/0x740
 netlink_release+0xe6a/0x1cf0
 __sock_release+0xcd/0x280
 sock_close+0x18/0x20
 __fput+0x27c/0xa90
 task_work_run+0xdd/0x1a0
 exit_to_user_mode_prepare+0x23c/0x250
 syscall_exit_to_user_mode+0x19/0x50
 do_syscall_64+0x42/0x80
 entry_SYSCALL_64_after_hwframe+0x63/0xcd

Second to last potentially related work creation:
 kasan_save_stack+0x1e/0x40
 __kasan_record_aux_stack+0xbe/0xd0
 call_rcu+0x99/0x740
 netlink_release+0xe6a/0x1cf0
 __sock_release+0xcd/0x280
 sock_close+0x18/0x20
 __fput+0x27c/0xa90
 task_work_run+0xdd/0x1a0
 exit_to_user_mode_prepare+0x23c/0x250
 syscall_exit_to_user_mode+0x19/0x50
 do_syscall_64+0x42/0x80
 entry_SYSCALL_64_after_hwframe+0x63/0xcd

Fixes: d0be8347 ("Bluetooth: L2CAP: Fix use-after-free caused by l2cap_chan_put")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

By using skb_put we ensure that skb->tail is set
correctly. Currently, skb->tail is always zero, which
leads to errors, such as the following page fault in
rfcomm_recv_frame:

    BUG: unable to handle page fault for address: ffffed1021de29ff
    #PF: supervisor read access in kernel mode
    #PF: error_code(0x0000) - not-present page
    RIP: 0010:rfcomm_run+0x831/0x4040 (net/bluetooth/rfcomm/core.c:1751)

Fixes: afd2daa2 ("Bluetooth: Add support for virtio transport driver")
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

hci_connect_cis and iso_connect_cis call hci_bind_cis inconsistently
with dst_type being either ISO socket address type or the HCI type, but
these values cannot be mixed like this. Fix this by using only the HCI
type.

CIS connection dst_type was also not initialized in hci_bind_cis, even
though it is used in hci_conn_hash_lookup_cis to find existing
connections.  Set the value in hci_bind_cis, so that existing CIS
connections are found e.g. when doing deferred socket connections, also
when dst_type is not 0 (ADDR_LE_DEV_PUBLIC).

Fixes: 26afbd82 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Fix the race condition between the following two flows that run in
parallel:

1. l2cap_reassemble_sdu -> chan->ops->recv (l2cap_sock_recv_cb) ->
   __sock_queue_rcv_skb.

2. bt_sock_recvmsg -> skb_recv_datagram, skb_free_datagram.

An SKB can be queued by the first flow and immediately dequeued and
freed by the second flow, therefore the callers of l2cap_reassemble_sdu
can't use the SKB after that function returns. However, some places
continue accessing struct l2cap_ctrl that resides in the SKB's CB for a
short time after l2cap_reassemble_sdu returns, leading to a
use-after-free condition (the stack trace is below, line numbers for
kernel 5.19.8).

Fix it by keeping a local copy of struct l2cap_ctrl.

BUG: KASAN: use-after-free in l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
Read of size 1 at addr ffff88812025f2f0 by task kworker/u17:3/43169

Workqueue: hci0 hci_rx_work [bluetooth]
Call Trace:
 <TASK>
 dump_stack_lvl (lib/dump_stack.c:107 (discriminator 4))
 print_report.cold (mm/kasan/report.c:314 mm/kasan/report.c:429)
 ? l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
 kasan_report (mm/kasan/report.c:162 mm/kasan/report.c:493)
 ? l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
 l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
 l2cap_rx (net/bluetooth/l2cap_core.c:7236 net/bluetooth/l2cap_core.c:7271) bluetooth
 ret_from_fork (arch/x86/entry/entry_64.S:306)
 </TASK>

Allocated by task 43169:
 kasan_save_stack (mm/kasan/common.c:39)
 __kasan_slab_alloc (mm/kasan/common.c:45 mm/kasan/common.c:436 mm/kasan/common.c:469)
 kmem_cache_alloc_node (mm/slab.h:750 mm/slub.c:3243 mm/slub.c:3293)
 __alloc_skb (net/core/skbuff.c:414)
 l2cap_recv_frag (./include/net/bluetooth/bluetooth.h:425 net/bluetooth/l2cap_core.c:8329) bluetooth
 l2cap_recv_acldata (net/bluetooth/l2cap_core.c:8442) bluetooth
 hci_rx_work (net/bluetooth/hci_core.c:3642 net/bluetooth/hci_core.c:3832) bluetooth
 process_one_work (kernel/workqueue.c:2289)
 worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2437)
 kthread (kernel/kthread.c:376)
 ret_from_fork (arch/x86/entry/entry_64.S:306)

Freed by task 27920:
 kasan_save_stack (mm/kasan/common.c:39)
 kasan_set_track (mm/kasan/common.c:45)
 kasan_set_free_info (mm/kasan/generic.c:372)
 ____kasan_slab_free (mm/kasan/common.c:368 mm/kasan/common.c:328)
 slab_free_freelist_hook (mm/slub.c:1780)
 kmem_cache_free (mm/slub.c:3536 mm/slub.c:3553)
 skb_free_datagram (./include/net/sock.h:1578 ./include/net/sock.h:1639 net/core/datagram.c:323)
 bt_sock_recvmsg (net/bluetooth/af_bluetooth.c:295) bluetooth
 l2cap_sock_recvmsg (net/bluetooth/l2cap_sock.c:1212) bluetooth
 sock_read_iter (net/socket.c:1087)
 new_sync_read (./include/linux/fs.h:2052 fs/read_write.c:401)
 vfs_read (fs/read_write.c:482)
 ksys_read (fs/read_write.c:620)
 do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
 entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)

Link: https://lore.kernel.org/linux-bluetooth/CAKErNvoqga1WcmoR3-0875esY6TVWFQDandbVZncSiuGPBQXLA@mail.gmail.com/T/#u
Fixes: d2a7ac5d ("Bluetooth: Add the ERTM receive state machine")
Fixes: 4b51dae9 ("Bluetooth: Add streaming mode receive and incoming packet classifier")
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>