When mangling packets forwarded to a HW checksumming capable device,
offload recalculation of the checksum instead of doing it in software.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The attached patch adds gratuitous arp filtering, more precisely: it
allows checking that the IPv4 source address matches the IPv4
destination address inside the ARP header. It also adds a check for the
hardware address type when matching MAC addresses (nothing critical,
just for better consistency).
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The attached patch by Michael Milner adds support for using iptables and
ip6tables on bridged traffic encapsulated in ppoe frames, similar to
what's already supported for vlan.
Signed-off-by: Michael Milner <milner@blissisland.ca>
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fills in missing documentation for dccp_sock fields.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This prints the value of the parsed Elapsed Time when received via a
Timestamp Echo option [RFC 4342, 13.3].
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes an error in the calculation of t_ipi when X converges towards
very low sending rates (between 1 and 64 bytes per second).

Although this case may not sound likely, it can be reproduced by connecting,
hitting enter (1 byte sent) and waiting for some time, during which the
nofeedback timer halves the sending rate until finally it reaches the region
1..64 bytes/sec. Computing X is handled correctly (tested separately); but by
dividing X _before_ entering the calculation of t_ipi, X becomes zero as
a result.  This in turn triggers a BUG condition caught in scaled_div().

Fixed by replacing with equivalent statement and explicit typecast for good
measure.

Calculation verified and effect of patch tested - reduced never below 1 byte
per 64 seconds afterwards, i.e. not allowing divide-by-zero.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow s390 to properly override the generic
__div64_32() implementation by:

1) Using obj-y for div64.o in s390's makefile instead
   of lib-y

2) Adding the weak attribute to the generic implementation.
Signed-off-by: David S. Miller <davem@davemloft.net>

skb_copy_expand changes the headroom, so it needs to adjust the header
offsets by the difference between the old and the new value.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rusty added a new 'stats' field to struct net_device.

loopback driver can use it instead of declaring another struct
net_device_stats This saves some memory.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch checks kmem_cache_create() error and aborts loading module
on failure.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>

For case of bridging pseudo devices, the get created/destroyed (Xen)
need to allow setting address to any valid value.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>

Need to tell STP daemon about more events, like any time a
device is added even when it is down.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>

This patchset based on work by Aji_Srinivas@emc.com provides allows
spanning tree to be controled from userspace.  Like hotplug, it
uses call_usermodehelper when spanning tree is enabled so there
is no visible API change. If call to start usermode STP fails
it falls back to existing kernel STP.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>

The RSTP daemon needs to be able to flush all dynamic forwarding
entries in the case of topology change.

This is a temporary interface. It will change to a netlink interface
before RSTP daemon is officially released.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>

Instead of hashing the whole Ethernet address, it should be faster
to just use the last 4 bytes. Add a random salt value to the hash
to make it more difficult to construct worst case DoS hash chains.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>

While in the STP learning state, don't route packets; wait until
forwarding delay has expired. The purpose of the forwarding delay
is to detect loops in the network, and if a brouter started up
and started forwarding, it could cause a flood.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>

Change the bridging hook to be simple function with return value
rather than modifying the skb argument. This could generate better
code and is cleaner.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>

When a transmitted packet is looped back directly, CHECKSUM_PARTIAL
maps to the semantics of CHECKSUM_UNNECESSARY.  Therefore we should
treat it as such in the stack.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

When csum_offset was introduced we did a conversion from csum to
csum_offset where applicable.  A couple of drivers were missed in
this process.

It was harmless to begin with since the two fields coincided.  Now
that we've made them different with the addition of csum_start, the
missed drivers must be converted or they can't send packets out at
all that require checksum offload.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skb transport pointer is currently used to specify the start
of the checksum region for transmit checksum offload.  Unfortunately,
the same pointer is also used during receive side processing.

This creates a problem when we want to retransmit a received
packet with partial checksums since the skb transport pointer
would be overwritten.

This patch solves this problem by creating a new 16-bit csum_start
offset value to replace the skb transport header for the purpose
of checksums.  This offset is calculated from skb->head so that
it does not have to change when skb->data changes.

No extra space is required since csum_offset itself fits within
a 16-bit word so we can use the other 16 bits for csum_start.

For backwards compatibility, just before we push a packet with
partial checksums off into the device driver, we set the skb
transport header to what it would have been under the old scheme.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

esp_init_state doesn't account for the beet pseudo header in the header_len
calculation, which may result in undersized skbs hitting xfrm4_beet_output,
causing unnecessary reallocations in ip_finish_output2.

The skbs should still always have enough room to avoid causing
skb_under_panic in skb_push since we have at least 16 bytes available
from LL_RESERVED_SPACE in xfrm_state_check_space.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the probing based MTU estimation, which usually takes 2-3 iterations
to find a fitting value and may underestimate the MTU, by an exact calculation.

Also fix underestimation of the XFRM trailer_len, which causes unnecessary
reallocations.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix incorrect switch of "trailer" skb by "skb" during skb_tail_pointer
conversion:

-       *(u8*)(trailer->tail - 1) = top_iph->protocol;
+       *(skb_tail_pointer(skb) - 1) = top_iph->protocol;

-       *(u8 *)(trailer->tail - 1) = *skb_network_header(skb);
+       *(skb_tail_pointer(skb) - 1) = *skb_network_header(skb);
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since we're increasing the headroom, the header offsets need to be
increased by the same amount as well.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

When looking up route for destination with rules with
source address restrictions, we may need to find a source
address for the traffic if not given.

Based on patch from Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove unnecessary initialization/variable.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The most common trigger of these errors is that the
config option hasn't been enable wich would make the
functionality available. Therefore returning EOPNOTSUPP
gives a better idea on what is going wrong.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move generic skbuff stuff from XFRM code to generic code so that
AF_RXRPC can use it too.

The kdoc comments I've attached to the functions needs to be checked
by whoever wrote them as I had to make some guesses about the workings
of these functions.
Signed-off-By: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>

Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>

To clearly state the intent of copying to linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>

We have to put back the cast to "char *" because these
pointers are volatile.

Reported by Andrew Morton.
Signed-off-by: David S. Miller <davem@davemloft.net>

Network drivers which keep stats allocate their own stats structure
then write a get_stats() function to return them.  It would be nice if
this were done by default.

1) Add a new "stats" field to "struct net_device".
2) Add a new feature field to say "this driver uses the internal one"
3) Have a default "get_stats" which returns NULL if that feature not set.
4) Change callers to check result of get_stats call for NULL, not if
   ->get_stats is set.

This should not break backwards compatibility with older drivers, yet
allow modern drivers to shed some boilerplate code.

Lightly tested: works for a modified lguest network driver.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to get more randomness for secure_tcpv6_sequence_number(),
secure_tcp_sequence_number(), secure_dccp_sequence_number() functions,
we can use the high resolution time services, providing nanosec
resolution.

I've also done two kmalloc()/kzalloc() conversions.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

For consistency with other skb data accessors, reducing the number of direct
accesses to skb->data.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

As IPPROTO_TCP is 6, it makes sense to make sure inet_protos[] array
is properly cache line aligned to avoid false sharing on SMP.

c0680540 b peer_total
c0680544 b inet_peer_unused_head
c0680560 B inet_protos

On i386 this example, we can see that inet_protos[IPPROTO_TCP] shares
a potentially hot (and modified) cache line.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_memory_pressure and tcp_socket currently share a cache line with tcp_memory_allocated, tcp_sockets_allocated.
(Very hot cache line)
It makes sense to declare these variables as __read_mostly, to avoid false sharing on SMP.

ffffffff8081d9c0 B tcp_orphan_count
ffffffff8081d9c4 B tcp_memory_allocated
ffffffff8081d9c8 B tcp_sockets_allocated
ffffffff8081d9cc B tcp_memory_pressure
ffffffff8081d9d0 b tcp_md5sig_users
ffffffff8081d9d8 b tcp_md5sig_pool
ffffffff8081d9e0 b warntime.31570
ffffffff8081d9e8 b tcp_socket
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The results of FIB rules lookups are cached in the routing cache
except for IPv6 as no such cache exists. So far, it was the
responsibility of the user to flush the cache after modifying any
rules. This lead to many false bug reports due to misunderstanding
of this concept.

This patch automatically flushes the route cache after inserting
or deleting a rule.

Thanks to Muli Ben-Yehuda <muli@il.ibm.com> for catching a bug
in the previous patch.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>