- 26 Sep, 2018 40 commits
-
-
Marcel Ziswiler authored
Add an evaluation board device tree more in-line with all our other device trees. Signed-off-by:
Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by:
Thierry Reding <treding@nvidia.com>
-
Marcel Ziswiler authored
Rename ac97 label to tegra_ac97 to be more in-line with the device tree binding documentation. Signed-off-by:
-
Marcel Ziswiler authored
Get rid of the fake clocks simple bus and use node names as per the actual schematics. Signed-off-by:
-
Marcel Ziswiler authored
Rename tps6586x@34 to pmic@34 and drop the unused pmic label. Signed-off-by:
-
Marcel Ziswiler authored
Drop unused i2c_ddc label. Signed-off-by:
-
Marcel Ziswiler authored
Rename i2c_ddc to hdmi_ddc to be more in-line with other device trees. Signed-off-by:
-
Marcel Ziswiler authored
Drop model and compatible nodes from the module level device tree as they get overridden by the carrier board device tree anyway. Signed-off-by:
-
Marcel Ziswiler authored
Add Colibri SSP aka SPI support using the SPI4 instance. Signed-off-by:
-
Marcel Ziswiler authored
Simplify model and compatible by dropping the 256/512 MB from the model, -512 from the compatible and rename that property from toradex,iris to toradex,colibri_t20-iris to be more in-line with all our other device trees. Signed-off-by:
-
Marcel Ziswiler authored
Simplify model and compatible by dropping the 256/512 MB from the model and -512 from the compatible properties to be more in-line with all our other device trees. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Marcel Ziswiler authored
Add compatibility comment. Signed-off-by:
-
Marcel Ziswiler authored
Annotate the SD card, its detect pin and move the SD card detect GPIO definition from the module to the carrier board more in-line with our other device trees. Signed-off-by:
-
Marcel Ziswiler authored
Add GPIO hogs for GMI_WR_N buffers: - tri-stating GMI_WR_N on SODIMM pin 99 nPWE - not tri-stating GMI_WR_N on SODIMM pin 93 RDnWR Signed-off-by:
-
Marcel Ziswiler authored
Add GPIO hog to unreset ASIX AX88772B USB Ethernet chip. Signed-off-by:
-
Marcel Ziswiler authored
Add i2c-thermtrip which would set the SLEEP MODE bit in the SUPPLYENE register of the TPS658643 PMIC. Signed-off-by:
-
Marcel Ziswiler authored
Rename and annotate LM95245 temperature sensor more in-line with our other device trees. Signed-off-by:
-
Marcel Ziswiler authored
Add dr_mode property to the USB controller. Signed-off-by:
-
Marcel Ziswiler authored
Add SODIMM pin 45 as GPIO wakeup key. Signed-off-by:
-
Marcel Ziswiler authored
Use high speed UART driver compatible nvidia,tegra20-hsuart. Signed-off-by:
-
Marcel Ziswiler authored
Add UART-C. Signed-off-by:
-
Marcel Ziswiler authored
Annotate UART-A and UART-B. Signed-off-by:
-
Marcel Ziswiler authored
Add display controller parallel RGB panel support incl. backlight PWM. Signed-off-by:
-
Marcel Ziswiler authored
Explicitly add pinmux' for all T20 SoC ball groups now: - Colibri Address/Data Bus (GMI) further pins used as GPIOs - Colibri BL_ON - Colibri EXT_IO* - Colibri L_BIAS, LCD_M1 is muxed with LCD_DE today's display need DE, disable LCD_M1 - more Colibri LCD pins (L_* resp. LDD<*>) - Colibri LCD (Optional 24 BPP Support) - Colibri MMCCD - uart_a_dsr and uart_a_dcd as GPIOs - Colibri USB_CDET - I2C3 (Optional) - JTAG_RTCK - LAN_RESET, LAN_EXT_WAKEUP and LAN_PME (All On-module) - more NAND pins - RESET_OUT - THERMD_ALERT# (On-module), unlatched I2C address pin of LM95245 temperature sensor therefore requires disabling for now Signed-off-by:
-
Marcel Ziswiler authored
Just cosmetic pinmux clean-up. Signed-off-by:
-
Marcel Ziswiler authored
Update sound nvidia,model to be more in-line with our other device trees. Signed-off-by:
-
Marcel Ziswiler authored
Cleaning up indentation, line-feed and white-space. Signed-off-by:
-
Marcel Ziswiler authored
Remove the phy-reset-gpio from the USB controller node as it is already specified in the PHY node. Signed-off-by:
-
Marcel Ziswiler authored
Annotate USB EHCI instances. Signed-off-by:
-
Marcel Ziswiler authored
Add missing regulators: - reg_lan_v_bus being USB Ethernet chip vbus supply - carrier board reg_3v3 to be used as backlight and panel power supply - carrier board HDMI supply being reg_5v0 - reg_usbc_vbus being the USB vbus supply of the EHCI instance 0 Signed-off-by:
-
Marcel Ziswiler authored
Just cosmetic regulator clean-up. Signed-off-by:
-
Marcel Ziswiler authored
Use no-1-8-v property rather than vmmc/vqmmc supplies and drop now obsolete and anyway non-existent vcc_sd. Signed-off-by:
-
Marcel Ziswiler authored
Reorder Host1x/HDMI properties. Signed-off-by:
-
Marcel Ziswiler authored
Add empty local-mac-address property to be filled in by boot loader (e.g. U-Boot). Signed-off-by:
-
Marcel Ziswiler authored
Annotate I2C busses: GEN2_I2C and CAM_I2C (I2C3) being unused and DDC_CLOCK/DATA on X3 pin 15/16 e.g. used for display EDID. Signed-off-by:
-
Marcel Ziswiler authored
Add rtc0 being the ultra low-power I2C one as found on the carrier board and the 3rd UART being NVIDIA's UARTB. Signed-off-by:
-
Marcel Ziswiler authored
Integrate support for GEN1_I2C aka I2C_SDA/SCL on SODIMM pin 194/196 and the M41T0M6 real time clock on the carrier board. Signed-off-by:
-
Marcel Ziswiler authored
Move RTC aliases from module to carrier board to be more in-line with all our other device trees. Signed-off-by:
-
Marcel Ziswiler authored
Drop unused hdmi_ddc label. Signed-off-by:
-
Marcel Ziswiler authored
Shorten temperature-sensor node to just temp-sensor as suggested in the binding documentation. Signed-off-by:
-
Marcel Ziswiler authored
Get rid of the fake clocks simple bus and use node names as per the actual schematics. Signed-off-by:
-
