- 31 Aug, 2012 7 commits
-
-
Sachin Kamat authored
Silences about 75 errors and warnings related to - Spacing - Alignment of braces - Line over 80 characters Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by:
Felipe Balbi <balbi@ti.com>
-
Sachin Kamat authored
Replace printk with corresponding pr_* and dev_err functions. Signed-off-by:
-
Sachin Kamat authored
Fixes the following warning: WARNING: Use #include <linux/io.h> instead of <asm/io.h> Signed-off-by:
-
Alan Stern authored
This patch (as1599) fixes dummy-hcd to make it update the appropriate driver pointer when a new gadget driver is bound or unbound. Without this change, the gadget driver's name doesn't appear in dev_printk output. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Roland Stigge authored
The lpc32xx_udc driver supported only one controller by defining a global static struct for it. This patch enables multiple instances of the controller by dynamic allocation of the struct at probe(). A static struct is kept as a template on initialization since it does some complex preset, reflecting fixed hardware endpoint structure. Signed-off-by:
Roland Stigge <stigge@antcom.de> Signed-off-by:
-
Roland Stigge authored
This patch removes the utilization of struct usb_endpoint_descriptor, as done by other drivers also. This was done on request by the USB gadget maintainers, since this API is obsoleted. Signed-off-by:
-
Roland Stigge authored
This patch adjusts the LPC32xx USB gadget driver to the new udc_start / udc_stop interface. Signed-off-by:
-
- 23 Aug, 2012 13 commits
-
-
Shimoda, Yoshihiro authored
When IORESOURCE_IRQ_SHAREABLE is set, the irq handler may be called even if the interupt of the USB module doesn't happen. So, it may clear the interrupt flags by mistake. This patch fixes it. Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by:
-
Andy Shevchenko authored
%pm already provides pretty print for mac addresses, let's use that and drop homebrew mac address printing. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Kevin Cernekee authored
usb_gadget_remove_driver() runs through a four-step sequence to shut down the gadget driver. For the case of a composite gadget + at91 UDC, this would look like: udc->driver->disconnect(udc->gadget); // composite_disconnect() usb_gadget_disconnect(udc->gadget); // at91_pullup(gadget, 0) udc->driver->unbind(udc->gadget); // composite_unbind() usb_gadget_udc_stop(udc->gadget, udc->driver); // at91_stop() The UDC driver can receive SETUP packets from the host up until the point when usb_gadget_disconnect() returns. On rare occasions, the gadget driver may see this sequence: udc->driver->disconnect(udc->gadget); // composite_disconnect() udc->driver->setup(udc->gadget, &ctrl); // composite_setup() udc->driver->unbind(udc->gadget); // composite_unbind() Some gadget drivers, such as composite, assume this will never happen and crash as a result. The fix is to quiesce the UDC hardware (via usb_gadget_disconnect) before running the gadget driver through the disconnect/unbind sequence. Reviewed-by:Peter Chen <peter.chen@freescale.com> Signed-off-by:
Kevin Cernekee <cernekee@gmail.com> Signed-off-by:
-
Andy Shevchenko authored
Acked-by:
Michal Nazarewicz <mina86@mina86.com> Signed-off-by:
-
Du, Changbin authored
The timeout values were 1000 and timeout issue occured many times on my s3c6410 Soc based board (mostly when booting whith USB cable not connected). This patch increase the values to 10000 to guarantee the success of reset. Having set timeout to 10000, I printed the remained timeout values which could cause timeout issue before this change (tested several times). the first timeout value remained: timeout = 8079 timeout = 8079 timeout = 8078 timeout = 8081 the second timeout value remained: timeout = 7940 timeout = 7945 timeout = 7940 timeout = 7938 Seeing from above values, I think the value 10000 is big enough. Signed-off-by:
Du, Changbin <changbin.du@gmail.com> Signed-off-by:
-
Michael Grzeschik authored
The lockdep hunter mentions a non consistent usage of spin_lock and spin_lock_irqsafe in the composite_disconnect and usb_function_activate function: [ 15.700897] ================================= [ 15.705255] [ INFO: inconsistent lock state ] [ 15.709617] 3.5.0-rc5+ #413 Not tainted [ 15.713453] --------------------------------- [ 15.717812] inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage. [ 15.723822] uvc-gadget/116 [HC1[1]:SC0[0]:HE0:SE1] takes: [ 15.729222] (&(&cdev->lock)->rlock){?.+...}, at: [<7f0049e8>] composite_disconnect+0x2c/0x74 [g_webcam] [ 15.738797] {HARDIRQ-ON-W} state was registered at: [ 15.743677] [<8006de3c>] mark_lock+0x148/0x688 [ 15.748325] [<8006ecb0>] __lock_acquire+0x934/0x1b74 [ 15.753481] [<8007047c>] lock_acquire+0x98/0x138 [ 15.758288] [<804c776c>] _raw_spin_lock+0x4c/0x84 [ 15.763188] [<7f006ae4>] usb_function_activate+0x28/0x94 [g_webcam] [ 15.769652] [<7f00820c>] usb_ep_autoconfig_reset+0x78/0x98 [g_webcam] [ 15.776287] [<7f0082a4>] uvc_v4l2_open+0x78/0x94 [g_webcam] [ 15.782054] [<80366a38>] v4l2_open+0x104/0x130 [ 15.786697] [<800efd30>] chrdev_open+0xa0/0x170 [ 15.791423] [<800e9718>] do_dentry_open.isra.13+0x1e8/0x264 [ 15.797186] [<800ea5d4>] nameidata_to_filp+0x58/0x94 [ 15.802340] [<800fa29c>] do_last.isra.31+0x2a0/0x808 [ 15.807497] [<800faa40>] path_openat+0xc8/0x3e8 [ 15.812216] [<800fae90>] do_filp_open+0x3c/0x90 [ 15.816936] [<800ea6fc>] do_sys_open+0xec/0x184 [ 15.821655] [<800ea7c4>] sys_open+0x30/0x34 [ 15.826027] [<8000e5c0>] ret_fast_syscall+0x0/0x48 [ 15.831015] irq event stamp: 6048 [ 15.834330] hardirqs last enabled at (6047): [<804c81b8>] _raw_spin_unlock_irqrestore+0x40/0x54 [ 15.843132] hardirqs last disabled at (6048): [<8000e174>] __irq_svc+0x34/0x60 [ 15.850370] softirqs last enabled at (5940): [<80028380>] __do_softirq+0x188/0x270 [ 15.858043] softirqs last disabled at (5935): [<80028944>] irq_exit+0xa0/0xa8 [ 15.865195] [ 15.865195] other info that might help us debug this: [ 15.871724] Possible unsafe locking scenario: [ 15.871724] [ 15.877645] CPU0 [ 15.880091] ---- [ 15.882537] lock(&(&cdev->lock)->rlock); [ 15.886659] <Interrupt> [ 15.889278] lock(&(&cdev->lock)->rlock); [ 15.893573] [ 15.893573] *** DEADLOCK *** [ 15.893573] [ 15.899496] no locks held by uvc-gadget/116. [ 15.903765] [ 15.903765] stack backtrace: [ 15.908125] Backtrace: [ 15.910604] [<80012038>] (dump_backtrace+0x0/0x114) from [<804bf8a4>] (dump_stack+0x20/0x24) [ 15.919043] r6:dfb8e6f0 r5:dfb8e400 r4:809717ec r3:60000193 [ 15.924766] [<804bf884>] (dump_stack+0x0/0x24) from [<804c0c0c>] (print_usage_bug+0x258/0x2c0) [ 15.933388] [<804c09b4>] (print_usage_bug+0x0/0x2c0) from [<8006e240>] (mark_lock+0x54c/0x688) [ 15.942006] [<8006dcf4>] (mark_lock+0x0/0x688) from [<8006edb8>] (__lock_acquire+0xa3c/0x1b74) [ 15.950625] [<8006e37c>] (__lock_acquire+0x0/0x1b74) from [<8007047c>] (lock_acquire+0x98/0x138) [ 15.959418] [<800703e4>] (lock_acquire+0x0/0x138) from [<804c78fc>] (_raw_spin_lock_irqsave+0x58/0x94) [ 15.968736] [<804c78a4>] (_raw_spin_lock_irqsave+0x0/0x94) from [<7f0049e8>] (composite_disconnect+0x2c/0x74 [g_webcam]) [ 15.979605] r7:00000012 r6:df82b0c4 r5:ded755bc r4:ded75580 [ 15.985331] [<7f0049bc>] (composite_disconnect+0x0/0x74 [g_webcam]) from [<8033c170>] (_gadget_stop_activity+0xc4/0x120) [ 15.996200] r6:df82b0c4 r5:df82b0c8 r4:df82b0d0 r3:7f0049bc [ 16.001919] [<8033c0ac>] (_gadget_stop_activity+0x0/0x120) from [<8033e390>] (udc_irq+0x724/0xcb8) [ 16.010877] r6:df82b010 r5:00000000 r4:df82b010 r3:00000000 [ 16.016595] [<8033dc6c>] (udc_irq+0x0/0xcb8) from [<8033baec>] (ci_irq+0x64/0xdc) [ 16.024086] [<8033ba88>] (ci_irq+0x0/0xdc) from [<80086538>] (handle_irq_event_percpu+0x74/0x298) [ 16.032958] r5:807fd414 r4:df38fdc0 [ 16.036566] [<800864c4>] (handle_irq_event_percpu+0x0/0x298) from [<800867a8>] (handle_irq_event+0x4c/0x6c) [ 16.046315] [<8008675c>] (handle_irq_event+0x0/0x6c) from [<80089318>] (handle_level_irq+0xbc/0x11c) [ 16.055447] r6:def04000 r5:807fd414 r4:807fd3c0 r3:00020000 [ 16.061166] [<8008925c>] (handle_level_irq+0x0/0x11c) from [<80085cc8>] (generic_handle_irq+0x38/0x4c) [ 16.070472] r5:807f7f64 r4:8081e9f8 [ 16.074082] [<80085c90>] (generic_handle_irq+0x0/0x4c) from [<8000ef98>] (handle_IRQ+0x5c/0xbc) [ 16.082788] [<8000ef3c>] (handle_IRQ+0x0/0xbc) from [<800085cc>] (tzic_handle_irq+0x6c/0x9c) [ 16.091225] r8:00000000 r7:def059b0 r6:00000001 r5:00000000 r4:00000000 r3:00000012 [ 16.099141] [<80008560>] (tzic_handle_irq+0x0/0x9c) from [<8000e184>] (__irq_svc+0x44/0x60) [ 16.107494] Exception stack(0xdef059b0 to 0xdef059f8) [ 16.112550] 59a0: 00000001 00000001 00000000 dfb8e400 [ 16.120732] 59c0: 40000013 81a2e500 00000000 81a2e500 00000000 00000000 80862418 def05a0c [ 16.128912] 59e0: def059c8 def059f8 80070e24 804c81bc 20000013 ffffffff [ 16.135542] [<804c8178>] (_raw_spin_unlock_irqrestore+0x0/0x54) from [<8003d0ec>] (__queue_work+0x108/0x470) [ 16.145369] r5:dfb1a30c r4:81b93c00 [ 16.148978] [<8003cfe4>] (__queue_work+0x0/0x470) from [<8003d4e0>] (queue_work_on+0x4c/0x54) [ 16.157511] [<8003d494>] (queue_work_on+0x0/0x54) from [<8003d544>] (queue_work+0x30/0x34) [ 16.165774] r6:df2e6900 r5:80e0c2f8 r4:dfb1a2c8 r3:def04000 [ 16.171495] [<8003d514>] (queue_work+0x0/0x34) from [<80493284>] (rpc_make_runnable+0x9c/0xac) [ 16.180113] [<804931e8>] (rpc_make_runnable+0x0/0xac) from [<80493c88>] (rpc_execute+0x40/0xa8) [ 16.188811] r5:def05ad4 r4:dfb1a2c8 [ 16.192426] [<80493c48>] (rpc_execute+0x0/0xa8) from [<8048c734>] (rpc_run_task+0xa8/0xb4) [ 16.200690] r8:00000001 r7:df74f520 r6:ded75700 r5:def05ad4 r4:dfb1a2c8 r3:00000002 [ 16.208618] [<8048c68c>] (rpc_run_task+0x0/0xb4) from [<801f1608>] (nfs_initiate_read+0xb4/0xd4) [ 16.217403] r5:df3e86c0 r4:00000000 [ 16.221015] [<801f1554>] (nfs_initiate_read+0x0/0xd4) from [<801f1c64>] (nfs_generic_pg_readpages+0x9c/0x114) [ 16.230937] [<801f1bc8>] (nfs_generic_pg_readpages+0x0/0x114) from [<801f0744>] (__nfs_pageio_add_request+0xe8/0x214) [ 16.241545] r8:000bf000 r7:00000000 r6:00000000 r5:deef4640 r4:def05c1c r3:801f1bc8 [ 16.249463] [<801f065c>] (__nfs_pageio_add_request+0x0/0x214) from [<801f0e3c>] (nfs_pageio_add_request+0x28/0x54) [ 16.259818] [<801f0e14>] (nfs_pageio_add_request+0x0/0x54) from [<801f1394>] (readpage_async_filler+0x114/0x170) [ 16.269992] r5:def05c58 r4:80fd7300 [ 16.273607] [<801f1280>] (readpage_async_filler+0x0/0x170) from [<800bb418>] (read_cache_pages+0xa0/0x108) [ 16.283259] r8:00200200 r7:00100100 r6:df74f654 r5:def05cd0 r4:80fd7300 [ 16.290034] [<800bb378>] (read_cache_pages+0x0/0x108) from [<801f218c>] (nfs_readpages+0xc4/0x168) [ 16.298999] [<801f20c8>] (nfs_readpages+0x0/0x168) from [<800bb1d0>] (__do_page_cache_readahead+0x254/0x354) [ 16.308833] [<800baf7c>] (__do_page_cache_readahead+0x0/0x354) from [<800bb5d0>] (ra_submit+0x38/0x40) [ 16.318145] [<800bb598>] (ra_submit+0x0/0x40) from [<800bb6b0>] (ondemand_readahead+0xd8/0x3b0) [ 16.326851] [<800bb5d8>] (ondemand_readahead+0x0/0x3b0) from [<800bba20>] (page_cache_async_readahead+0x98/0xa8) [ 16.337043] [<800bb988>] (page_cache_async_readahead+0x0/0xa8) from [<800b2118>] (generic_file_aio_read+0x5b4/0x7c4) [ 16.347565] r6:00000000 r5:df74f654 r4:80fd70a0 [ 16.352231] [<800b1b64>] (generic_file_aio_read+0x0/0x7c4) from [<801e82c0>] (nfs_file_read+0x7c/0xcc) [ 16.361544] [<801e8244>] (nfs_file_read+0x0/0xcc) from [<800eab80>] (do_sync_read+0xb4/0xf4) [ 16.369981] r9:00000000 r8:def05f70 r7:00000000 r6:00000000 r5:dec34900 r4:fffffdee [ 16.377896] [<800eaacc>] (do_sync_read+0x0/0xf4) from [<800eb548>] (vfs_read+0xb4/0x144) [ 16.385987] r8:00000000 r7:def05f70 r6:76a95008 r5:003e3dd6 r4:dec34900 [ 16.392761] [<800eb494>] (vfs_read+0x0/0x144) from [<800eb624>] (sys_read+0x4c/0x78) [ 16.400504] r8:00000000 r7:00000003 r6:003e3dd6 r5:76a95008 r4:dec34900 [ 16.407279] [<800eb5d8>] (sys_read+0x0/0x78) from [<8000e5c0>] (ret_fast_syscall+0x0/0x48) [ 16.415543] r9:def04000 r8:8000e864 r6:000086b4 r5:00000000 r4:00000000 [ 20.872729] gadget: high-speed config #1: Video [ 20.877368] gadget: uvc_function_set_alt(0, 0) [ 20.881908] gadget: uvc_function_set_alt(1, 0) [ 20.891464] gadget: uvc_function_set_alt(1, 0) Signed-off-by:Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by:
-
Neil Zhang authored
Fix boot up hang when enable udc without otg enabled. The root cause is that the clock will be shut down when probe routine is finished because of clock gating. When a gadget driver is registered at this time, it will call mv_udc_start which in turn will call mv_udc_vbus_session. If there is no cable attached at the boot up time, the vbus is low, so it will call stop_activity path without clock enabled which will cause system hang then. Actually, we need't go this path when clock is disabled, what we need to do is just jump out. Signed-off-by:
Neil Zhang <zhangwm@marvell.com> Signed-off-by:
-
Yunfan Zhang authored
Fix system hang in udc shutdown routine which caused by accessing usb register when clock is disabled. So enable usb clock before access register. Signed-off-by:
Yunfan Zhang <yfzhang@marvell.com> Signed-off-by:
-
Chao Xie authored
In order to support iso, we need do the following things: 1. fix length for one dtd 2. allow req contains multiple packets for a ISO transfer Signed-off-by:
Chao Xie <chao.xie@marvell.com> Signed-off-by:
Yu Xu <yuxu@marvell.com> Signed-off-by:
-
Neil Zhang authored
According to ChipIdea's reference manual in section 8.5.2 "Non-streaming operational mode in device mode", we'd better enable stream mode, especially that ISO endpoints are not supported when the SDIS bit is set. Signed-off-by:
-
Neil Zhang authored
build_dtd() can be called when hold a spinlock, but GFP_KERNEL may cause dma_pool_alloc() sleep, So we need use GFP_ATOMIC instead of GFP_KERNEL. But using GFP_ATOMIC may cause failure when allocating memory, add error handler to handle it. Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Neil Zhang authored
Clean unused code for mv_udc driver. Signed-off-by:
-
Neil Zhang authored
There are several places use udelay(LOOPS_USEC) to wait the status to be changed, but the delay interval is a bit too long, so reduce it to enhance the performance. Signed-off-by:
-
- 16 Aug, 2012 11 commits
-
-
Linus Torvalds authored
-
Ian Kent authored
Following a report of a crash during an automount expire I found that the locking in fs/autofs4/expire.c:get_next_positive_subdir() was wrong. Not only is the locking wrong but the function is more complex than it needs to be. The function is meant to calculate (and dget) the next entry in the list of directories contained in the root of an autofs mount point (an autofs indirect mount to be precise). The main problem was that the d_lock of the owner of the list was not being taken when walking the list, which lead to list corruption under load. The only other lock that needs to be taken is against the next dentry candidate so it can be checked for usability. Signed-off-by:
Ian Kent <raven@themaw.net> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://github.com/awilliam/linux-vfioLinus Torvalds authored
Pull VFIO fix from Alex Williamson: "Just a trivial patch to include vfio.h in the installed headers so we can complete userspace integration into QEMU." * tag 'vfio-for-v3.6-rc1' of git://github.com/awilliam/linux-vfio: vfio: Include vfio.h in installed headers
-
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuseLinus Torvalds authored
Pull fuse updates from Miklos Szeredi. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse: fuse: verify all ioctl retry iov elements fuse: add missing INIT flag descriptions fuse: add missing INIT flags fuse: update attributes on aio_read fuse: invalidate inode mapping if mtime changes fuse: add FUSE_AUTO_INVAL_DATA init flag
-
Linus Torvalds authored
Merge tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen Pull Xen fix from Konrad Rzeszutek Wilk: "Way back in v3.5 we added a mechanism to populate back pages that were released (they overlapped with MMIO regions), but neglected to reserve the proper amount of virtual space for extend_brk to work properly. Coincidentally some other commit aligned the _brk space to larger area so I didn't trigger this until it was run on a machine with more than 2GB of MMIO space." * On machines with large MMIO/PCI E820 spaces we fail to boot b/c we failed to pre-allocate large enough virtual space for extend_brk. * tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: xen/p2m: Reserve 8MB of _brk space for P2M leafs when populating back.
-
git://github.com/pmundt/linux-shLinus Torvalds authored
Pull SuperH fixes from Paul Mundt. * tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: sh: intc: Handle domain association for sparseirq pre-allocated vectors. sh: sh7269: Fix LCD pinmux sh: dma: fix request_irq usage
-
Dan Williams authored
Moved to djbw@fb.com Cc: Dave Jiang <dave.jiang@intel.com> Cc: Vinod Koul <vinod.koul@linux.intel.com> Signed-off-by:
Dan Williams <djbw@fb.com> Signed-off-by:
-
Borislav Petkov authored
When dumping "Code: " sections from an oops, the trapping instruction %rip points to can be a string copy 2b:* f3 a5 rep movsl %ds:(%rsi),%es:(%rdi) and the line contain a bunch of ":". Current "cut" selects only the and the second field output looks funnily overlaid this: 2b:* f3 a5 rep movsl %ds <-- trapping instruction:(%rsi),%es:(%rdi Fix this by selecting the remaining fields too. Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: linux-kbuild@vger.kernel.org Signed-off-by:
Borislav Petkov <borislav.petkov@amd.com> Signed-off-by:
-
git://git.infradead.org/users/vkoul/slave-dmaLinus Torvalds authored
Pull two slave-dmaengine fixes from Vinod Koul: "One fixes the correct use of clock API in imx driver and the other enables clock for tegra driver, which is used for other tegra driver conversion to dmanegine in -next." * 'fixes' of git://git.infradead.org/users/vkoul/slave-dma: dma: tegra: enable/disable dma clock dma: imx-dma: Fix kernel crash due to missing clock conversion
-
git://people.freedesktop.org/~airlied/linuxLinus Torvalds authored
Pull more drm fixes from Dave Airlie: "Just some intel and nouveau ones this time, intel has more edp panel fixes for macbooks and nouveau has a suspend/resume regression fix in there." * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: drm/i915: Apply post-sync write for pipe control invalidates drm/i915: reorder edp disabling to fix ivb MacBook Air drm/nv86/fifo: suspend fix drm/nouveau: disable copy engine on NVAF nouveau: fixup scanout enable in nvc0_pm drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate drm/i915: ensure i2c adapter is all set before adding it drm/i915: ignore eDP bpc settings from vbt drm/i915: Fix blank panel at reopening lid drm/nve0/fifo: add support for the flip completion swmthd
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparcLinus Torvalds authored
Pull two sparc fixes from David S. Miller. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc: sparc64: Be less verbose during vmemmap population. sparc64: do not clobber personality flags in sys_sparc64_personality()
-
- 15 Aug, 2012 3 commits
-
-
git://git.freedesktop.org/git/nouveau/linux-2.6Dave Airlie authored
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6: drm/nv86/fifo: suspend fix drm/nouveau: disable copy engine on NVAF nouveau: fixup scanout enable in nvc0_pm drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate drm/nve0/fifo: add support for the flip completion swmthd
-
git://people.freedesktop.org/~danvet/drm-intelDave Airlie authored
Daniel Vetter writes: "A few important fixers: - fix various lvds backlight issues, regressed in 3.6 (Takashi Iwai) - make the retina mbp work (ignore bogus edp bpc value in vbt) - fix a gmbus regression introduced in (iirc) 3.4 (Jani Nikula) - fix an edp panel power sequence regression, fixes the new macbook air - apply the tlb invalidate w/a Otherwise we still have another gmbus regression (patches are awaiting tested-bys) and there's something odd going with some rare systems not entering rc6 often enough (and hence blowing through too much power). It seems to be a timing-related issue and can be mitigated by frobbing the magic tuning parameters. We're still working on that one. Also, we still have some fallout from the hw context support, but you can only hit that with mesa master." * 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel: drm/i915: Apply post-sync write for pipe control invalidates drm/i915: reorder edp disabling to fix ivb MacBook Air drm/i915: ensure i2c adapter is all set before adding it drm/i915: ignore eDP bpc settings from vbt drm/i915: Fix blank panel at reopening lid
-
David S. Miller authored
On a 2-node machine with 256GB of ram we get 512 lines of console output, which is just too much. This mimicks Yinghai Lu's x86 commit c2b91e2e (x86_64/mm: check and print vmemmap allocation continuous) except that we aren't ever going to get contiguous block pointers in between calls so just print when the virtual address or node changes. This decreases the output by an order of 16. Also demote this to KERN_DEBUG. Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 14 Aug, 2012 5 commits
-
-
Chris Wilson authored
When invalidating the TLBs it is documentated as requiring a post-sync write. Failure to do so seems to result in a GPU hang. Exposure to this hang on IVB seems to be a result of removing the extra stalls required for SNB pipecontrol workarounds: commit 6c6cf5aa Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Fri Jul 20 18:02:28 2012 +0100 drm/i915: Only apply the SNB pipe control w/a to gen6 Note: Manually switch the pipe_control cmd to 4 dwords to avoid a (silent) functional conflict with -next. This way will get a loud (but conflict with next (since the scratch_addr has been deleted there). Reported-and-tested-by: yex.tian@intel.com Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53322Acked-by:
Ben Widawsky <ben@bwidawsk.net> Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> [danvet: added note about merge conflict with -next.] Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
Daniel Vetter authored
eDP is tons of fun. It turns out that at least the new MacBook Air 5,1 model absolutely doesn't like the new force vdd dance we've introduced in commit 6cb49835 Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Sun May 20 17:14:50 2012 +0200 drm/i915: enable vdd when switching off the eDP panel But that patch also tried to fix some neat edp sequence issue with the force_vdd timings. Closer inspection reveals that we've raised force_vdd only to do the aux channel communication dp_sink_dpms. If we move the edp_panel_off below that, we don't need any force_vdd for the disable sequence, which makes the Air happy. Unfortunately the reporter of the original bug that the above commit fixed is travelling, so we can't test whether this regresses things. But my theory is that since we don't check for any power-off -> force_vdd-on delays in edp_panel_vdd_on, this was the actual root-cause of this failure. With that force_vdd dance completely eliminated, I'm hopeful the original bug stays fixed, too. For reference the old bug, which hopefully doesn't get broken by this: https://bugzilla.kernel.org/show_bug.cgi?id=43163 In any case, regression fixers win over plain bugfixes, so this needs to go in asap. v2: The crucial pieces seems to be to clear the force_vdd flag uncoditionally, too, in edp_panel_off. Looks like this is left behind by the firmware somehow. v3: The Apple firmware seems to switch off the panel on it's own, hence we still need to keep force_vdd on, but properly clear it when switching the panel off. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45671Tested-by:
Roberto Romer <sildurin@gmail.com> Tested-by:
Daniel Wagner <wagi@monom.org> Tested-by:
Keith Packard <keithp@keithp.com> Cc: stable@vger.kernel.org Cc: Keith Packard <keithp@keithp.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linuxLinus Torvalds authored
Pull s390 patches from Martin Schwidefsky: "Included are bug fixes and a patch to enable system call filtering with BPF." * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/compat: fix mmap compat system calls s390/compat: fix compat wrappers for process_vm system calls s390: do not clobber personality flags in sys_32_personality() s390/seccomp: add support for system call filtering using BPF s390/sclp_sdias: Add missing break and "fall through" s390/mm: remove MAX_PHYSADDR_BITS define
-
git://people.freedesktop.org/~airlied/linuxLinus Torvalds authored
Pull drm fixes from Dave Airlie: "Radeon and intel fixes mostly, one fix to the mgag200 driver to not hang on certain server variants." * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (32 commits) drm/radeon: fix typo in function header comment drm/radeon/kms: implement timestamp userspace query (v2) drm/radeon/kms: add MSAA texture support for r600-evergreen drm/radeon/kms: reorder code in r600_check_texture_resource drm/radeon: fence virtual address and free it once idle v4 drm/radeon: fix some missing parens in asic macros drm/radeon: add some new SI pci ids drm/radeon: fix ordering in pll picking on dce4+ drm/radeon: do not reenable crtc after moving vram start address drm/radeon: fix bank tiling parameters on cayman drm/radeon: fix bank tiling parameters on evergreen drm/radeon: fix bank tiling parameters on SI drm/radeon: properly handle crtc powergating drm/radeon: properly handle SS overrides on TN (v2) drm/radeon/dce4+: set a more reasonable cursor watermark drm/radeon: fix handling for ddc type 5 on combios drm/mgag200: fix G200ER pll picking algorithm drm/edid: Fix potential memory leak in edid_load() drm/udl: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1] drm/radeon/kms: allow "invalid" DB formats as a means to disable DB ...
-
Arnd Bergmann authored
Commit 72121572 ("GPIO: gpio-pxa: fix devicetree functions") added an "xlate" function pointer to the irq_domain_ops, but this function is nor declared or defined anywhere when CONFIG_OF is disabled, causing the build error: drivers/gpio/gpio-pxa.c:532:11: error: 'irq_domain_xlate_twocell' undeclared here (not in a function) Extending the DT-only code section to cover the irq_domain_ops and the pxa_gpio_dt_ids solves this problem and makes it clearer which code is actually used without DT. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
- 13 Aug, 2012 1 commit
-
-
Maxim Levitsky authored
This fix is a backport from the reworked nouveau driver. It masks off the engines we're not expecting to use before attempting a channel kickoff. Signed-off-by:
Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by:
Ben Skeggs <bskeggs@redhat.com>
-
