Just like MT7916 also MT7981 can handle 3T3R DBDC frontend and should
hence be included in the corresponding conditional expression in the
driver. Add it.

Fixes: 6bad146d ("wifi: mt76: mt7915: add support for MT7981")
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The offset of the TSSI flag on the EEPROM of MT7981 devices was wrong.
Set the correct offset instead.

Fixes: 6bad146d ("wifi: mt76: mt7915: add support for MT7981")
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add a BSS eht_support check before returning EHT phy mode. Without this
patch, there might be an inconsistency where the softmac layer thinks
the BSS is in HE mode, while the FW thinks it is in EHT mode.
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Implement beacon protection feature for mt7996 chipsets, and also do
some cleanup on the set key routine.
Co-developed-by: Rudra Shahi <rudra.shahi@mediatek.com>
Signed-off-by: Rudra Shahi <rudra.shahi@mediatek.com>
Signed-off-by: Allen Ye <allen.ye@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add sta_rec_ht_uni struct to pass HT ampdu params to firmware. For VHT,
HE, and EHT mode, firmware will get the ampdu params by parsing the
corresponding capability.
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix the alignment of struct mt7996_mcu_all_sta_info_event.

Fixes: adde3eed ("wifi: mt76: mt7996: Add mcu commands for getting sta tx statistic")
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

During runtime, the GI value in the WTBL is not updated in real-time. To
obtain the latest results for the TX GI, switch to use an MCU command.
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The power gain value is related to total TX path, so change the
calculation to use per-phy chainmask.
Signed-off-by: Allen Ye <allen.ye@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add support for setting txpower from upper layer and configuring per-rate
txpower limit table.
Co-developed-by: Allen Ye <allen.ye@mediatek.com>
Signed-off-by: Allen Ye <allen.ye@mediatek.com>
Co-developed-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use per-phy structure for maximum txpower value initializing, since each
phy may have a different chainmask, which can impact the calculation of
power gain.
Co-developed-by: Allen Ye <allen.ye@mediatek.com>
Signed-off-by: Allen Ye <allen.ye@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

For UBPR and FILS frames, the BSS_CHANGED_BEACON flag will also be set,
which causes those frames to use the beacon rate in TX descriptors.
Adjust the statement to fix this issue.

Fixes: 98686cd2 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use the new fixed rate command format to let the fixed field function
work normally.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Make mt7996_mcu_set_fixed_field() non-static in order to handle
IEEE80211_RC_SMPS_CHANGED in mt7996_mac_sta_rc_work().
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Always set the fixed_bw bitfield for fixed rate frames to keep it being
sent with specific bandwidth. Without this change, the bw of fixed rate
frames will still be decided by hardware.
Reported-by: Chank Chen <chank.chen@mediatek.com>
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Refactor and update dma prefetch parts and also split band 1 traffic to
PCIe 1 to enhance throughput.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Align the format of struct bss_rate_tlv to the firmware.

Fixes: 98686cd2 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

For connac3 chipsets, setting of spe_idx is moved from TX descriptor to
the fixed rate table. This patch implements the setting to support
duplicate TX mode for beacon.
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This patch adds support for thermal sensor device, including the
following features:
- Support to read current chip temperature.
- Support to set/get the trigger/restore temperature for thermal service.
- Support to read current chip tx cycle.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Implement thermal protection commands and support Linux cooling device
control for mt7996 chipsets.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add EHT statistics of beamforming feedback and BW320 in debugfs tx_stats
command.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add support to correctly configure the rx chainmask of variants that
have additional auxiliary RX path. e.g., 4T5R.
The auxiliary RX path is transparent to driver, but driver needs to
correctly configure it in the set channel fw command.
Co-developed-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

wifi: mt76: mt7915: fallback to non-wed mode if platform_get_resource fails in mt7915_mmio_wed_init()

mt76 assumes mt7915_mmio_wed_init can fail just after wed driver has
been attached running mtk_wed_device_attach().
Fall back to non-wed mode if platform_get_resource fails in
mt7915_mmio_wed_init routines.

Fixes: eebb7097 ("wifi: mt76: mt7915: enable wed for mt7986-wmac chipset")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce the capability to clear WED rro session configured in the hw
according to the event reported by the MCU firmware
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce the capability to reset mt7996 chipset if requested by wed
driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move WED reset code shared between mt7915 and mt7996 in common module.
This is a preliminary patch to introduce WED reset support for mt7996.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Similar to MT7915, enable Wireless Ethernet Ditpatcher for MT7996
to offload traffic received from the WLAN nic and transmitted on the
LAN one
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to introduce WED rx support for mt7996
driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Similar to MT7915, enable Wireless Ethernet Ditpatcher for MT7996
to offload traffic received from the LAN nic and transmitted on the
WLAN one
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce mtk_wed_device pointer in mt76_queue structure in order to
configure WED chip.
Get rid of dev parameter in Q_READ and Q_WRITE macros.
Introduce wed parameter to the following routine signatures:
- mt76_init_queue
- mt76_init_tx_queue

This is a preliminary patch to introduce WED support for mt7996 since
mt7996 runs two separate WED chips.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76_mmio_wed_offload_enable and mt76_mmio_wed_offload_disable routines
will be reused by mt7996 driver for wed support.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76_mmio_wed_init_rx_buf and mt76_mmio_wed_release_rx_buf routines
in common code.
This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

No need cast (void *) to (struct mt7615_phy *).
Signed-off-by: Wu Yunchuan <yunchuan@nfschina.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Permit to load precal from NVMEM cell for mt7915. The NVMEM cell must be
named "precal" to be correctly loaded.

NVMEM cell must already account the correct offset and be placed after
the EEPROM as the function expect the data right from the start.
Tested-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Generilize mt76_get_of_eeprom_from_nvmem to use alternative cell name by
passing the cell name as an arg and expose it.

Rename it to mt76_get_of_data_from_nvmem to better reflect the now more
generic usage.

This is to permit driver to load additional cell, like precal cell.
Tested-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Since mt76_get_of_eeprom is not used by mt7915 anymore, unexport it and
make it static again.

Also drop offset arg as it's only supported for MTD and was always set
to 0, hardcode the MTD functio instead.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Limit support for precal loading for mt7915 only to MTD. Passing data
from DT doesn't support offset and NVMEM require a different cell name
and doesn't support offset hence only MTD way is actually supported.

Rename mt76_get_of_eeprom_from_mtd to mt76_get_of_data_from_mtd as it is
now used for a more generic purpose and export it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>