Add a driver for the Cadence SD4HC SD/SDIO/eMMC Controller.

For SD, it basically relies on the SDHCI standard code.
For eMMC, this driver provides some callbacks to support the
hardware part that is specific to this IP design.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Some SDHCI-compat controllers support not only SD, but also eMMC,
but they use different commands for tuning: CMD19 for SD, CMD21 for
eMMC.

Due to the difference of the underlying mechanism, some controllers
(at least, the Cadence IP is the case) provide their own registers
for the eMMC tuning.

This commit will be useful when we want to override .execute_tuning
callback (for eMMC HS200 tuning), but still let it fall back to
sdhci_execute_tuning() for SD timing.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Tidy the tuning loop by moving it to a separate function and making it a
for-loop.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There are only 2 possible block sizes, so simplify 2 if-statements into 1.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Factor out some functions to tidy up the code in sdhci_execute_tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use mmc_abort_tuning() instead of open-coding the stop command.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If a tuning command times out, the card could still be processing it, which
will cause problems for recovery. The eMMC specification says that CMD12
can be used to stop CMD21, so add a function that does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

SDHCI falls back to fixed sampling if there is an error during tuning.
However it also reports an error unless there is periodic re-tuning.
That is not the best option because:
a) there is a reasonable chance that fixed sampling will work, especially
at room temperature.
b) re-tuning will be done again anyway if there are CRC errors.
Change to return no error always when falling back to fixed sampling.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If the driver has exhausted the maximum number of tuning loops, then fixed
sampling is used. To do that both SDHCI_CTRL_TUNED_CLK and
SDHCI_CTRL_EXEC_TUNING must be reset to 0, but only SDHCI_CTRL_TUNED_CLK
was being reset. Reset SDHCI_CTRL_EXEC_TUNING to 0 also.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Clearing the tuning bits should reset the tuning circuit. However there is
more to do. Reset the command and data lines for good measure, and then
for eMMC ensure the card is not still trying to process a tuning command by
sending a stop command.

Note the JEDEC eMMC specification says the stop command (CMD12) can be used
to stop a tuning command (CMD21) whereas the SD specification is silent on
the subject with respect to the SD tuning command (CMD19). Considering that
CMD12 is not a valid SDIO command, the stop command is sent only when the
tuning command is CMD21 i.e. for eMMC. That addresses cases seen so far
which have been on eMMC.

Note that this replaces the commit fe5fb2e3 ("mmc: sdhci: Reset cmd and
data circuits after tuning failure") which is being reverted for v4.9+.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dan O'Donovan <dan@emutex.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This reverts commit fe5fb2e3 ("mmc: sdhci: Reset cmd and data circuits
after tuning failure").

A better fix is available, and it will be applied to older stable releases,
so get this out of the way by reverting it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The JEDEC specification indicates CMD13 can be used after a HS200 switch
to check for errors. However in practice some boards experience CRC errors
in the CMD13 response. Consequently, for HS200, CRC errors are not a
reliable way to know the switch failed. If there really is a problem, we
would expect tuning will fail and the result ends up the same. So change
the error condition to ignore CRC errors in that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add an entry for the SDIO bus in the ECS EF20 cherry trail laptop:

  Device (SDHB) {
    Name (_ADR, 0x00110000)
    Name (_HID, "80860F14" /* Intel Baytrail SDIO/MMC Host Controller */)
    Name (_CID, "PNP0D40" /* SDA Standard Compliant SD Host Controller */)
    Name (_DDN, "Intel(R) SDIO Controller - 80862295")
    Name (_UID, 0x02)
    Name (_HRV, One)

A SDHB device with the same _HID and _UID can also be found on other
cherry trail products like Chuwi Hi10.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

I see no override of read/write callbacks in sdhci-of-at91.c.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

On NI 9037 boards the max SDIO frequency is limited by trace lengths
and other layout choices. The max SDIO frequency is stored in an ACPI
table.

The driver reads the ACPI entry MXFQ during sdio_probe_slot and sets the
f_max field of the host.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewed-by: Jaeden Amero <jaeden.amero@ni.com>
Reviewed-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add PCI ID for Intel byt sdio host controller sub-vended by NI.

The controller has different behavior because of the board layout NI
puts it on.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Before calling clk_round_rate(), put the spin_unlock_irq() in
sdhci_s3c_consider_clock() function.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When card is polling (broken-cd), there is a spamming messge related to
clock.
After applied this patch, display the message only one time at boot
time. It's enough to check which clock values is used.
Also prevent to display the spamming message.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If card is polling or non-removable, display the more exact message.
It's helpful to debug which detecting scheme is using.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Before checking flags, it has to check "present" variable.
Otherwise, flags should be cleared everytime.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The commit 64997de4fd17 ("mmc: dw_mmc: remove system PM callback") is
missing to call dw_mci_ctrl_reset(). This adds to call
dw_mci_ctrl_reset() and to handle error of clocks.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The dw_mmc-exynos should be RPM_ACTIVE on probe() to call suspend
callback of runtime PM in pm_runtime_force_suspend() during first system
suspend. Also call pm_runtime_get_noresume() on probe() because it
doesn't call suspend/resume callback by runtime PM now.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It is unnecessary to panic the kernel when testing mmc. Instead,
cast a warning for folkz to debug and return the error code to
the caller to indicate the failure of this test should be enough.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

bounce_sg for mqrq_cur and mqrq_pre are proper
allocated when initializing the queue and will not
be freed before explicitly cleaning the queue. So from
the code itself it should be quite confident to remove
this check. If that BUG_ON take effects, it is mostly
likely the memory is randomly oopsing.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The code seems quite simple to maintain the sdio_uart_table,
and the insert/remove port from the table are symmetric. If
the BUG_ON occurs, which means serial_core modify the index
or mess up the port sequence anyway.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Return error value for file_operations callback instead
of triggering BUG_ON which is meaningless. Personally I
don't believe n != EXT_CSD_STR_LEN could happen. Anyway,
propagate the error to the caller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add definitions relating to Command Queuing.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add a mmc_queue member to record the size of the queue, which currently
supports 2 requests on-the-go at a time. Instead of allocating resources
for 2 slots in the queue, allow for an arbitrary number.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In preparation for supporting a queue of requests, factor out
mmc_queue_reqs_free_bufs().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In preparation for supporting a queue of requests, factor out
mmc_queue_alloc_sgs().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In preparation for supporting a queue of requests, factor out
mmc_queue_alloc_bounce_sgs().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
[Ulf: Fixed compiler warning]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In preparation for supporting a queue of requests, factor out
mmc_queue_alloc_bounce_bufs().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
[Ulf: Fixed compiler warning]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The only time the driver sleeps expecting to be woken upon the arrival of
a new request, is when the dispatch queue is empty. The only time that it
is known whether the dispatch queue is empty is after NULL is returned
from blk_fetch_request() while under the queue lock.

Recognizing those facts, simplify the synchronization between the queue
thread and the request function. A couple of flags tell the request
function what to do, and the queue lock and barriers associated with
wake-ups ensure synchronization.

The result is simpler and allows the removal of the context_info lock.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The 4K native sector check does not allow for the 'do' loop nor the
variables used after the 'cmd_abort' label.

'brq' and 'req' get reassigned in the 'do' loop, so the check must not
assume what their values are. After the 'cmd_abort' label, 'mq_rq' and
'req' are used, but 'rqc' must be NULL otherwise it can be started again.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

We get the following warning with the driver is compiled in:

WARNING: modpost: Found 1 section mismatch(es).
To see full details build your kernel with:
'make CONFIG_DEBUG_SECTION_MISMATCH=y'

With CONFIG_DEBUG_SECTION_MISMATCH enabled, the details are reported:

WARNING: vmlinux.o(.text+0x55d014): Section mismatch in reference from the
function fsl_guts_probe() to the function
.init.text:of_flat_dt_get_machine_name()
The function fsl_guts_probe() references
the function __init of_flat_dt_get_machine_name().
This is often because fsl_guts_probe lacks a __init
annotation or the annotation of of_flat_dt_get_machine_name is wrong.

This patch fixes the issue by using the normal DT/OF API rather than
the of_flat_* one.

Cc: Scott Wood <oss@buserror.net>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>