- 18 Jul, 2017 36 commits
-
-
Takashi Iwai authored
commit f363a066 upstream. In the commit [15c75b09: ALSA: ctxfi: Fallback DMA mask to 32bit], I forgot to put "!" at dam_set_mask() call check in cthw20k1.c (while cthw20k2.c is OK). This patch fixes that obvious bug. (As a side note: although the original commit was completely wrong, it's still working for most of machines, as it sets to 32bit DMA mask in the end. So the bug severity is low.) Fixes: 15c75b09 ("ALSA: ctxfi: Fallback DMA mask to 32bit") Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Daniel Borkmann authored
commit e7ede72a upstream. The current symbols__fixup_end() heuristic for the last entry in the rb tree is suboptimal as it leads to not being able to recognize the symbol in the call graph in a couple of corner cases, for example: i) If the symbol has a start address (f.e. exposed via kallsyms) that is at a page boundary, then the roundup(curr->start, 4096) for the last entry will result in curr->start == curr->end with a symbol length of zero. ii) If the symbol has a start address that is shortly before a page boundary, then also here, curr->end - curr->start will just be very few bytes, where it's unrealistic that we could perform a match against. Instead, change the heuristic to roundup(curr->start, 4096) + 4096, so that we can catch such corner cases and have a better chance to find that specific symbol. It's still just best effort as the real end of the symbol is unknown to us (and could even be at a larger offset than the current range), but better than the current situation. Alexei reported that he recently run into case i) with a JITed eBPF program (these are all page aligned) as the last symbol which wasn't properly shown in the call graph (while other eBPF program symbols in the rb tree were displayed correctly). Since this is a generic issue, lets try to improve the heuristic a bit. Reported-and-Tested-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Fixes: 2e538c4a ("perf tools: Improve kernel/modules symbol lookup") Link: http://lkml.kernel.org/r/bb5c80d27743be6f12afc68405f1956a330e1bc9.1489614365.git.daniel@iogearbox.netSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Oliver Neukum authored
commit cdd7928d upstream. The gadget code exports the bitfield for serial status changes over the wire in its internal endianness. The fix is to convert to little endian before sending it over the wire. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Tested-by:
家瑋 <momo1208@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust filename, context] Signed-off-by:
-
Johan Hovold authored
commit 687e0687 upstream. USBTMC devices are required to have a bulk-in and a bulk-out endpoint, but the driver failed to verify this, something which could lead to the endpoint addresses being taken from uninitialised memory. Make sure to zero all private data as part of allocation, and add the missing endpoint sanity check. Note that this also addresses a more recently introduced issue, where the interrupt-in-presence flag would also be uninitialised whenever the optional interrupt-in endpoint is not present. This in turn could lead to an interrupt urb being allocated, initialised and submitted based on uninitialised values. Fixes: dbf3e7f6 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.") Fixes: 5b775f67 ("USB: add USB test and measurement class driver") Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
David Ahern authored
commit 4ee39733 upstream. Anycast routes have the RTF_ANYCAST flag set, but when dumping routes for userspace the route type is not set to RTN_ANYCAST. Make it so. Fixes: 58c4fb86 ("[IPV6]: Flag RTF_ANYCAST for anycast routes") CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Signed-off-by:
David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
David S. Miller <davem@davemloft.net> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Johan Hovold authored
commit cb1b4946 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit ba340d7b upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: bba5394a ("Input: add support for Hanwang tablets") Signed-off-by:
-
Johan Hovold authored
commit 5cc4a1a9 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: aca951a2 ("[PATCH] input-driver-yealink-P1K-usb-phone") Signed-off-by:
-
Johan Hovold authored
commit ac2ee9ba upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: c04148f9 ("Input: add driver for USB VoIP phones with CM109...") Signed-off-by:
-
Johan Hovold authored
commit 59cf8bed upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory that lie beyond the end of the endpoint array should a malicious device lack the expected endpoints. Signed-off-by:
-
Johan Hovold authored
commit 181302dc upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: 53f3a9e2 ("mmc: USB SD Host Controller (USHC) driver") Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Peter Zijlstra authored
commit e7cc4865 upstream. While hunting for clues to a use-after-free, Oleg spotted that perf_event_init_context() can loose an error value with the result that fork() can succeed even though we did not fully inherit the perf event context. Spotted-by:
Oleg Nesterov <oleg@redhat.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: oleg@redhat.com Fixes: 889ff015 ("perf/core: Split context's event group list into pinned and non-pinned lists") Link: http://lkml.kernel.org/r/20170316125823.190342547@infradead.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Matt Fleming authored
commit 6e5f32f7 upstream. If we crossed a sample window while in NO_HZ we will add LOAD_FREQ to the pending sample window time on exit, setting the next update not one window into the future, but two. This situation on exiting NO_HZ is described by: this_rq->calc_load_update < jiffies < calc_load_update In this scenario, what we should be doing is: this_rq->calc_load_update = calc_load_update [ next window ] But what we actually do is: this_rq->calc_load_update = calc_load_update + LOAD_FREQ [ next+1 window ] This has the effect of delaying load average updates for potentially up to ~9seconds. This can result in huge spikes in the load average values due to per-cpu uninterruptible task counts being out of sync when accumulated across all CPUs. It's safe to update the per-cpu active count if we wake between sample windows because any load that we left in 'calc_load_idle' will have been zero'd when the idle load was folded in calc_global_load(). This issue is easy to reproduce before, commit 9d89c257 ("sched/fair: Rewrite runnable load and utilization average tracking") just by forking short-lived process pipelines built from ps(1) and grep(1) in a loop. I'm unable to reproduce the spikes after that commit, but the bug still seems to be present from code review. Signed-off-by:
Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by:
-
Peter Zijlstra authored
commit 9bbb25af upstream. Thomas spotted that fixup_pi_state_owner() can return errors and we fail to unlock the rt_mutex in that case. Reported-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Darren Hart <dvhart@linux.intel.com> Cc: juri.lelli@arm.com Cc: bigeasy@linutronix.de Cc: xlpang@redhat.com Cc: rostedt@goodmis.org Cc: mathieu.desnoyers@efficios.com Cc: jdesfossez@efficios.com Cc: dvhart@infradead.org Cc: bristot@redhat.com Link: http://lkml.kernel.org/r/20170304093558.867401760@infradead.orgSigned-off-by:
-
Peter Zijlstra authored
commit c236c8e9 upstream. While working on the futex code, I stumbled over this potential use-after-free scenario. Dmitry triggered it later with syzkaller. pi_mutex is a pointer into pi_state, which we drop the reference on in unqueue_me_pi(). So any access to that pointer after that is bad. Since other sites already do rt_mutex_unlock() with hb->lock held, see for example futex_lock_pi(), simply move the unlock before unqueue_me_pi(). Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Dan Williams authored
commit 6e9f44ea upstream. Add Quectel UC15, UC20, EC21, and EC25. The EC20 is handled by qcserial due to a USB VID/PID conflict with an existing Acer device. Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Samuel Thibault authored
commit 3243367b upstream. Some USB 2.0 devices erroneously report millisecond values in bInterval. The generic config code manages to catch most of them, but in some cases it's not completely enough. The case at stake here is a USB 2.0 braille device, which wants to announce 10ms and thus sets bInterval to 10, but with the USB 2.0 computation that yields to 64ms. It happens that one can type fast enough to reach this interval and get the device buffers overflown, leading to problematic latencies. The generic config code does not catch this case because the 64ms is considered a sane enough value. This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk to mark devices which actually report milliseconds in bInterval, and marks Vario Ultra devices as needing it. Signed-off-by:
Samuel Thibault <samuel.thibault@ens-lyon.org> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Johan Hovold authored
commit 4ce36271 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Note that the dereference happens in the cmd and wait_init_done callbacks which are called during probe. Fixes: 1ba47da5 ("uwb: add the i1480 DFU driver") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
-
Johan Hovold authored
commit daf229b1 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Note that the dereference happens in the start callback which is called during probe. Fixes: de520b8b ("uwb: add HWA radio controller driver") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
-
Johan Hovold authored
commit 03ace948 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. This specifically fixes the NULL-pointer dereference when probing HWA HC devices. Fixes: df365423 ("wusb: add the Wire Adapter (WA) core") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
-
Johan Hovold authored
commit f259ca3e upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. Note that the endpoint access that causes the NULL-deref is currently only used for debugging purposes during probe so the oops only happens when dynamic debugging is enabled. This means the driver could be rewritten to continue to accept device with only two endpoints, should such devices exist. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit b0addd3f upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit 6e526fdf upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. The endpoints are specifically dereferenced in the i2400m_bootrom_init path during probe (e.g. in i2400mu_tx_bulk_out). Fixes: f398e424 ("i2400m/USB: probe/disconnect, dev init/shutdown and reset backends") Cc: Inaky Perez-Gonzalez <inaky@linux.intel.com> Signed-off-by:
-
Johan Hovold authored
commit 68c32f9c upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: cf7776dc ("[PATCH] isdn4linux: Siemens Gigaset drivers - direct USB connection") Cc: Hansjoerg Lipp <hjlipp@web.de> Signed-off-by:
-
Alexey Kodanev authored
commit 4b3b45ed upstream. commit c146066a ("ipv4: Don't use ufo handling on later transformed packets") and commit f89c56ce ("ipv6: Don't use ufo handling on later transformed packets") added a check that 'rt->dst.header_len' isn't zero in order to skip UFO, but it doesn't include IPcomp in transport mode where it equals zero. Packets, after payload compression, may not require further fragmentation, and if original length exceeds MTU, later compressed packets will be transmitted incorrectly. This can be reproduced with LTP udp_ipsec.sh test on veth device with enabled UFO, MTU is 1500 and UDP payload is 2000: * IPv4 case, offset is wrong + unnecessary fragmentation udp_ipsec.sh -p comp -m transport -s 2000 & tcpdump -ni ltp_ns_veth2 ... IP (tos 0x0, ttl 64, id 45203, offset 0, flags [+], proto Compressed IP (108), length 49) 10.0.0.2 > 10.0.0.1: IPComp(cpi=0x1000) IP (tos 0x0, ttl 64, id 45203, offset 1480, flags [none], proto UDP (17), length 21) 10.0.0.2 > 10.0.0.1: ip-proto-17 * IPv6 case, sending small fragments udp_ipsec.sh -6 -p comp -m transport -s 2000 & tcpdump -ni ltp_ns_veth2 ... IP6 (flowlabel 0x6b9ba, hlim 64, next-header Compressed IP (108) payload length: 37) fd00::2 > fd00::1: IPComp(cpi=0x1000) IP6 (flowlabel 0x6b9ba, hlim 64, next-header Compressed IP (108) payload length: 21) fd00::2 > fd00::1: IPComp(cpi=0x1000) Fix it by checking 'rt->dst.xfrm' pointer to 'xfrm_state' struct, skip UFO if xfrm is set. So the new check will include both cases: IPcomp and IPsec. Fixes: c146066a ("ipv4: Don't use ufo handling on later transformed packets") Fixes: f89c56ce ("ipv6: Don't use ufo handling on later transformed packets") Signed-off-by:
Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by:
-
Johan Hovold authored
commit de46e566 upstream. Make sure to verify that we have the required interrupt-out endpoint for IOWarrior56 devices to avoid dereferencing a NULL-pointer in write should a malicious device lack such an endpoint. Fixes: 946b960d ("USB: add driver for iowarrior devices.") Signed-off-by:
-
Stefan Brüns authored
commit 67b0503d upstream. The buffer allocation for the firmware data was changed in commit 43fab979 ("[media] dvb-usb: don't use stack for firmware load") but the same applies for the reset value. Fixes: 43fab979 ("[media] dvb-usb: don't use stack for firmware load") Signed-off-by:
Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 43fab979 upstream. As reported by Marc Duponcheel <marc@offline.be>, firmware load on dvb-usb is using the stack, with is not allowed anymore on default Kernel configurations: [ 1025.958836] dvb-usb: found a 'WideView WT-220U PenType Receiver (based on ZL353)' in cold state, will try to load a firmware [ 1025.958853] dvb-usb: downloading firmware from file 'dvb-usb-wt220u-zl0353-01.fw' [ 1025.958855] dvb-usb: could not stop the USB controller CPU. [ 1025.958856] dvb-usb: error while transferring firmware (transferred size: -11, block size: 3) [ 1025.958856] dvb-usb: firmware download failed at 8 with -22 [ 1025.958867] usbcore: registered new interface driver dvb_usb_dtt200u [ 2.789902] dvb-usb: downloading firmware from file 'dvb-usb-wt220u-zl0353-01.fw' [ 2.789905] ------------[ cut here ]------------ [ 2.789911] WARNING: CPU: 3 PID: 2196 at drivers/usb/core/hcd.c:1584 usb_hcd_map_urb_for_dma+0x430/0x560 [usbcore] [ 2.789912] transfer buffer not dma capable [ 2.789912] Modules linked in: btusb dvb_usb_dtt200u(+) dvb_usb_af9035(+) btrtl btbcm dvb_usb dvb_usb_v2 btintel dvb_core bluetooth rc_core rfkill x86_pkg_temp_thermal intel_powerclamp coretemp crc32_pclmul aesni_intel aes_x86_64 glue_helper lrw gf128mul ablk_helper cryptd drm_kms_helper syscopyarea sysfillrect pcspkr i2c_i801 sysimgblt fb_sys_fops drm i2c_smbus i2c_core r8169 lpc_ich mfd_core mii thermal fan rtc_cmos video button acpi_cpufreq processor snd_hda_codec_realtek snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm snd_timer snd crc32c_intel ahci libahci libata xhci_pci ehci_pci xhci_hcd ehci_hcd usbcore usb_common dm_mirror dm_region_hash dm_log dm_mod [ 2.789936] CPU: 3 PID: 2196 Comm: systemd-udevd Not tainted 4.9.0-gentoo #1 [ 2.789937] Hardware name: ASUS All Series/H81I-PLUS, BIOS 0401 07/23/2013 [ 2.789938] ffffc9000339b690 ffffffff812bd397 ffffc9000339b6e0 0000000000000000 [ 2.789939] ffffc9000339b6d0 ffffffff81055c86 000006300339b6a0 ffff880116c0c000 [ 2.789941] 0000000000000000 0000000000000000 0000000000000001 ffff880116c08000 [ 2.789942] Call Trace: [ 2.789945] [<ffffffff812bd397>] dump_stack+0x4d/0x66 [ 2.789947] [<ffffffff81055c86>] __warn+0xc6/0xe0 [ 2.789948] [<ffffffff81055cea>] warn_slowpath_fmt+0x4a/0x50 [ 2.789952] [<ffffffffa006d460>] usb_hcd_map_urb_for_dma+0x430/0x560 [usbcore] [ 2.789954] [<ffffffff814ed5a8>] ? io_schedule_timeout+0xd8/0x110 [ 2.789956] [<ffffffffa006e09c>] usb_hcd_submit_urb+0x9c/0x980 [usbcore] [ 2.789958] [<ffffffff812d0ebf>] ? copy_page_to_iter+0x14f/0x2b0 [ 2.789960] [<ffffffff81126818>] ? pagecache_get_page+0x28/0x240 [ 2.789962] [<ffffffff8118c2a0>] ? touch_atime+0x20/0xa0 [ 2.789964] [<ffffffffa006f7c4>] usb_submit_urb+0x2c4/0x520 [usbcore] [ 2.789967] [<ffffffffa006feca>] usb_start_wait_urb+0x5a/0xe0 [usbcore] [ 2.789969] [<ffffffffa007000c>] usb_control_msg+0xbc/0xf0 [usbcore] [ 2.789970] [<ffffffffa067903d>] usb_cypress_writemem+0x3d/0x40 [dvb_usb] [ 2.789972] [<ffffffffa06791cf>] usb_cypress_load_firmware+0x4f/0x130 [dvb_usb] [ 2.789973] [<ffffffff8109dbbe>] ? console_unlock+0x2fe/0x5d0 [ 2.789974] [<ffffffff8109e10c>] ? vprintk_emit+0x27c/0x410 [ 2.789975] [<ffffffff8109e40a>] ? vprintk_default+0x1a/0x20 [ 2.789976] [<ffffffff81124d76>] ? printk+0x43/0x4b [ 2.789977] [<ffffffffa0679310>] dvb_usb_download_firmware+0x60/0xd0 [dvb_usb] [ 2.789979] [<ffffffffa0679898>] dvb_usb_device_init+0x3d8/0x610 [dvb_usb] [ 2.789981] [<ffffffffa069e302>] dtt200u_usb_probe+0x92/0xd0 [dvb_usb_dtt200u] [ 2.789984] [<ffffffffa007420c>] usb_probe_interface+0xfc/0x270 [usbcore] [ 2.789985] [<ffffffff8138bf95>] driver_probe_device+0x215/0x2d0 [ 2.789986] [<ffffffff8138c0e6>] __driver_attach+0x96/0xa0 [ 2.789987] [<ffffffff8138c050>] ? driver_probe_device+0x2d0/0x2d0 [ 2.789988] [<ffffffff81389ffb>] bus_for_each_dev+0x5b/0x90 [ 2.789989] [<ffffffff8138b7b9>] driver_attach+0x19/0x20 [ 2.789990] [<ffffffff8138b33c>] bus_add_driver+0x11c/0x220 [ 2.789991] [<ffffffff8138c91b>] driver_register+0x5b/0xd0 [ 2.789994] [<ffffffffa0072f6c>] usb_register_driver+0x7c/0x130 [usbcore] [ 2.789994] [<ffffffffa06a5000>] ? 0xffffffffa06a5000 [ 2.789996] [<ffffffffa06a501e>] dtt200u_usb_driver_init+0x1e/0x20 [dvb_usb_dtt200u] [ 2.789997] [<ffffffff81000408>] do_one_initcall+0x38/0x140 [ 2.789998] [<ffffffff8116001c>] ? __vunmap+0x7c/0xc0 [ 2.789999] [<ffffffff81124fb0>] ? do_init_module+0x22/0x1d2 [ 2.790000] [<ffffffff81124fe8>] do_init_module+0x5a/0x1d2 [ 2.790002] [<ffffffff810c96b1>] load_module+0x1e11/0x2580 [ 2.790003] [<ffffffff810c68b0>] ? show_taint+0x30/0x30 [ 2.790004] [<ffffffff81177250>] ? kernel_read_file+0x100/0x190 [ 2.790005] [<ffffffff810c9ffa>] SyS_finit_module+0xba/0xc0 [ 2.790007] [<ffffffff814f13e0>] entry_SYSCALL_64_fastpath+0x13/0x94 [ 2.790008] ---[ end trace c78a74e78baec6fc ]--- So, allocate the structure dynamically. Signed-off-by:
-
Johan Hovold authored
commit 8c76d7cd upstream. Add missing sanity check to the bulk-in completion handler to avoid an integer underflow that could be triggered by a malicious device. This avoids leaking up to 56 bytes from after the URB transfer buffer to user space. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit 0b1d250a upstream. Fix a NULL-pointer dereference in the interrupt callback should a malicious device send data containing a bad port number by adding the missing sanity check. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Anton Blanchard authored
commit 85e8a239 upstream. We see lpfc devices regularly fail during kexec. Fix this by adding a shutdown method which mirrors the remove method. Signed-off-by:
Anton Blanchard <anton@samba.org> Reviewed-by:
Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Tested-by:
Martin K. Petersen <martin.petersen@oracle.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Kai-Heng Feng authored
commit 45838660 upstream. The aux port does not get detected without noloop quirk, so external PS/2 mouse cannot work as result. The PS/2 mouse can work with this quirk. BugLink: https://bugs.launchpad.net/bugs/1591053Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Reviewed-by:
Marcos Paulo de Souza <marcos.souza.org@gmail.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
commit 934767c5 upstream. The return status of the adapter check on KERNEL_PANIC is supposed to be the upper 16 bits of the OMR status register. Fixes: c421530b (scsi: aacraid: Reorder Adpater status check) Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by:
Dave Carroll <david.carroll@microsemi.com> Signed-off-by:
-
Felipe Balbi authored
commit 7369090a upstream. Some gadget drivers are bad, bad boys. We notice that ADB was passing bad Burst Size which caused top bits of param0 to be overwritten which confused DWC3 when running this command. In order to avoid future issues, we're going to make sure values passed by macros are always safe for the controller. Note that ADB still needs a fix to *not* pass bad values. Reported-by:
Mohamed Abbas <mohamed.abbas@intel.com> Sugested-by:
Adam Andruszak <adam.andruszak@intel.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Rik van Riel authored
commit bf7165cf upstream. There are several trace include files that define TRACE_INCLUDE_FILE. Include several of them in the same .c file (as I currently have in some code I am working on), and the compile will blow up with a "warning: "TRACE_INCLUDE_FILE" redefined #define TRACE_INCLUDE_FILE syscalls" Every other include file in include/trace/events/ avoids that issue by having a #undef TRACE_INCLUDE_FILE before the #define; syscalls.h should have one, too. Link: http://lkml.kernel.org/r/20160928225554.13bd7ac6@annuminas.surriel.com Fixes: b8007ef7 ("tracing: Separate raw syscall from syscall tracer") Signed-off-by:
Rik van Riel <riel@redhat.com> Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Dan Streetman authored
commit c74fd80f upstream. Revert the main part of commit: af42b8d1 ("xen: fix MSI setup and teardown for PV on HVM guests") That commit introduced reading the pci device's msi message data to see if a pirq was previously configured for the device's msi/msix, and re-use that pirq. At the time, that was the correct behavior. However, a later change to Qemu caused it to call into the Xen hypervisor to unmap all pirqs for a pci device, when the pci device disables its MSI/MSIX vectors; specifically the Qemu commit: c976437c7dba9c7444fb41df45468968aaa326ad ("qemu-xen: free all the pirqs for msi/msix when driver unload") Once Qemu added this pirq unmapping, it was no longer correct for the kernel to re-use the pirq number cached in the pci device msi message data. All Qemu releases since 2.1.0 contain the patch that unmaps the pirqs when the pci device disables its MSI/MSIX vectors. This bug is causing failures to initialize multiple NVMe controllers under Xen, because the NVMe driver sets up a single MSIX vector for each controller (concurrently), and then after using that to talk to the controller for some configuration data, it disables the single MSIX vector and re-configures all the MSIX vectors it needs. So the MSIX setup code tries to re-use the cached pirq from the first vector for each controller, but the hypervisor has already given away that pirq to another controller, and its initialization fails. This is discussed in more detail at: https://lists.xen.org/archives/html/xen-devel/2017-01/msg00447.html Fixes: af42b8d1 ("xen: fix MSI setup and teardown for PV on HVM guests") Signed-off-by:
Dan Streetman <dan.streetman@canonical.com> Reviewed-by:
Stefano Stabellini <sstabellini@kernel.org> Acked-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
- 02 Jul, 2017 4 commits
-
-
Ben Hutchings authored
-
Mikulas Patocka authored
commit 83cd904d upstream. Commit 6bd4837d ("mm: simplify find_vma_prev()") broke memory management on PA-RISC. After application of the patch, programs that allocate big arrays on the stack crash with segfault, for example, this will crash if compiled without optimization: int main() { char array[200000]; array[199999] = 0; return 0; } The reason is that PA-RISC has up-growing stack and the stack is usually the last memory area. In the above example, a page fault happens above the stack. Previously, if we passed too high address to find_vma_prev, it returned NULL and stored the last VMA in *pprev. After "simplify find_vma_prev" change, it stores NULL in *pprev. Consequently, the stack area is not found and it is not expanded, as it used to be before the change. This patch restores the old behavior and makes it return the last VMA in *pprev if the requested address is higher than address of any other VMA. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Acked-by:
KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
KOSAKI Motohiro authored
commit 6bd4837d upstream. commit 297c5eee ("mm: make the vma list be doubly linked") added the vm_prev member to vm_area_struct. We can simplify find_vma_prev() by using it. Also, this change helps to improve page fault performance because it has stronger locality of reference. Signed-off-by:
KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Hugh Dickins <hughd@google.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Shaohua Li <shaohua.li@intel.com> Cc: Michal Hocko <mhocko@suse.cz> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
David Howells authored
commit 5f2f9765 upstream. This fixes CVE-2017-7482. When a kerberos 5 ticket is being decoded so that it can be loaded into an rxrpc-type key, there are several places in which the length of a variable-length field is checked to make sure that it's not going to overrun the available data - but the data is padded to the nearest four-byte boundary and the code doesn't check for this extra. This could lead to the size-remaining variable wrapping and the data pointer going over the end of the buffer. Fix this by making the various variable-length data checks use the padded length. Reported-by:
石磊 <shilei-c@360.cn> Signed-off-by:
David Howells <dhowells@redhat.com> Reviewed-by:
Marc Dionne <marc.c.dionne@auristor.com> Reviewed-by:
-
