- 29 Jun, 2017 40 commits
-
-
Greg Kroah-Hartman authored
-
Arend Van Spriel authored
commit 35abcd4f upstream. This fixes the following warning: drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c: In function 'brcmf_usb_probe_phase2': drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c:1198:2: warning: 'devinfo' may be used uninitialized in this function [-Wmaybe-uninitialized] mutex_unlock(&devinfo->dev_init_lock); Fixes: 6d0507a7 ("brcmfmac: add parameter to pass error code in firmware callback") Cc: Stephen Rothwell <sfr@canb.auug.org.au> Reported-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Gleb Fotengauer-Malinovskiy authored
commit 7292ae3d upstream. The latest change of asm goto support check added passing of KBUILD_CFLAGS to compiler. When these flags reference gcc plugins that are not built yet, the check fails. When one runs "make bzImage" followed by "make modules", the kernel is always built with HAVE_JUMP_LABEL disabled, while the modules are built depending on CONFIG_JUMP_LABEL. If HAVE_JUMP_LABEL macro happens to be different, modules are built with undefined references, e.g.: ERROR: "static_key_slow_inc" [net/netfilter/xt_TEE.ko] undefined! ERROR: "static_key_slow_dec" [net/netfilter/xt_TEE.ko] undefined! ERROR: "static_key_slow_dec" [net/netfilter/nft_meta.ko] undefined! ERROR: "static_key_slow_inc" [net/netfilter/nft_meta.ko] undefined! ERROR: "nf_hooks_needed" [net/netfilter/ipvs/ip_vs.ko] undefined! ERROR: "nf_hooks_needed" [net/ipv6/ipv6.ko] undefined! ERROR: "static_key_count" [net/ipv6/ipv6.ko] undefined! ERROR: "static_key_slow_inc" [net/ipv6/ipv6.ko] undefined! This change moves the check before all these references are added to KBUILD_CFLAGS. This is correct because subsequent KBUILD_CFLAGS modifications are not relevant to this check. Reported-by:
Anton V. Boyarshinov <boyarsh@altlinux.org> Fixes: 35f860f9 ("jump label: pass kbuild_cflags when checking for asm goto support") Signed-off-by:
Gleb Fotengauer-Malinovskiy <glebfm@altlinux.org> Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Acked-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Acked-by:
David Lin <dtwlin@google.com> Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
-
Russell King authored
commit 898805e0 upstream. The Marvell driver incorrectly provides phydev->lp_advertising as the logical and of the link partner's advert and our advert. This is incorrect - this field is supposed to store the link parter's unmodified advertisment. This allows ethtool to report the correct link partner auto-negotiation status. Fixes: be937f1f ("Marvell PHY m88e1111 driver fix") Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Amit Pundir <amit.pundir@linaro.org> Signed-off-by:
-
Hauke Mehrtens authored
commit 833bfade upstream. The generic SPI code calculates how long the issued transfer would take and adds 100ms in addition to the timeout as tolerance. On my 500 MHz Lantiq Mips SoC I am getting timeouts from the SPI like this when the system boots up: m25p80 spi32766.4: SPI transfer timed out blk_update_request: I/O error, dev mtdblock3, sector 2 SQUASHFS error: squashfs_read_data failed to read block 0x6e After increasing the tolerance for the timeout to 200ms I haven't seen these SPI transfer time outs any more. The Lantiq SPI driver in use here has an extra work queue in between, which gets triggered when the controller send the last word and the hardware FIFOs used for reading and writing are only 8 words long. Signed-off-by:
Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Matthias Reichl authored
commit 2201ac61 upstream. The code responsible for splitting periods into chunks that can be handled by the DMA controller missed to update total_len, the number of bytes processed in the current period, when there are more chunks to follow. Therefore total_len was stuck at 0 and the code didn't work at all. This resulted in a wrong control block layout and audio issues because the cyclic DMA callback wasn't executing on period boundaries. Fix this by adding the missing total_len update. Signed-off-by:
Matthias Reichl <hias@horus.com> Signed-off-by:
Martin Sperl <kernel@martin.sperl.org> Tested-by:
Clive Messer <clive.messer@digitaldreamtime.co.uk> Reviewed-by:
Eric Anholt <eric@anholt.net> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Yendapally Reddy Dhananjaya Reddy authored
commit bb1a6197 upstream. USB PHYs need the MDIO clock divisor enabled earlier to work. Initialize mdio clock divisor in probe function. The ext bus bit available in the same register will be used by mdio mux to enable external mdio. Signed-off-by:
Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com> Fixes: ddc24ae1 ("net: phy: Broadcom iProc MDIO bus driver") Reviewed-by:
Jon Mason <jon.mason@broadcom.com> Signed-off-by:
-
Stanislaw Gruszka authored
commit 6232c174 upstream. As reported by Felix: Though protected by an ifdef, introducing an usb symbol dependency in the rt2x00lib module is a major inconvenience for distributions that package kernel modules split into individual packages. Get rid of this unnecessary dependency by calling the usb related function from a more suitable place. Cc: Vishal Thanki <vishalthanki@gmail.com> Reported-by:
Felix Fietkau <nbd@nbd.name> Fixes: 8b4c0009 ("rt2x00usb: Use usb anchor to manage URB") Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
William Wu authored
commit b7f73850 upstream. Companion descriptor is only used for SuperSpeed endpoints, if the endpoints are HighSpeed or FullSpeed, the Companion descriptor will not allocated, so we can only access it if gadget is SuperSpeed. I can reproduce this issue on Rockchip platform rk3368 SoC which supports USB 2.0, and use functionfs for ADB. Kernel build with CONFIG_KASAN=y and CONFIG_SLUB_DEBUG=y report the following BUG: ================================================================== BUG: KASAN: slab-out-of-bounds in ffs_func_set_alt+0x224/0x3a0 at addr ffffffc0601f6509 Read of size 1 by task swapper/0/0 ============================================================================ BUG kmalloc-256 (Not tainted): kasan: bad access detected ---------------------------------------------------------------------------- Disabling lock debugging due to kernel taint INFO: Allocated in ffs_func_bind+0x52c/0x99c age=1275 cpu=0 pid=1 alloc_debug_processing+0x128/0x17c ___slab_alloc.constprop.58+0x50c/0x610 __slab_alloc.isra.55.constprop.57+0x24/0x34 __kmalloc+0xe0/0x250 ffs_func_bind+0x52c/0x99c usb_add_function+0xd8/0x1d4 configfs_composite_bind+0x48c/0x570 udc_bind_to_driver+0x6c/0x170 usb_udc_attach_driver+0xa4/0xd0 gadget_dev_desc_UDC_store+0xcc/0x118 configfs_write_file+0x1a0/0x1f8 __vfs_write+0x64/0x174 vfs_write+0xe4/0x200 SyS_write+0x68/0xc8 el0_svc_naked+0x24/0x28 INFO: Freed in inode_doinit_with_dentry+0x3f0/0x7c4 age=1275 cpu=7 pid=247 ... Call trace: [<ffffff900808aab4>] dump_backtrace+0x0/0x230 [<ffffff900808acf8>] show_stack+0x14/0x1c [<ffffff90084ad420>] dump_stack+0xa0/0xc8 [<ffffff90082157cc>] print_trailer+0x188/0x198 [<ffffff9008215948>] object_err+0x3c/0x4c [<ffffff900821b5ac>] kasan_report+0x324/0x4dc [<ffffff900821aa38>] __asan_load1+0x24/0x50 [<ffffff90089eb750>] ffs_func_set_alt+0x224/0x3a0 [<ffffff90089d3760>] composite_setup+0xdcc/0x1ac8 [<ffffff90089d7394>] android_setup+0x124/0x1a0 [<ffffff90089acd18>] _setup+0x54/0x74 [<ffffff90089b6b98>] handle_ep0+0x3288/0x4390 [<ffffff90089b9b44>] dwc_otg_pcd_handle_out_ep_intr+0x14dc/0x2ae4 [<ffffff90089be85c>] dwc_otg_pcd_handle_intr+0x1ec/0x298 [<ffffff90089ad680>] dwc_otg_pcd_irq+0x10/0x20 [<ffffff9008116328>] handle_irq_event_percpu+0x124/0x3ac [<ffffff9008116610>] handle_irq_event+0x60/0xa0 [<ffffff900811af30>] handle_fasteoi_irq+0x10c/0x1d4 [<ffffff9008115568>] generic_handle_irq+0x30/0x40 [<ffffff90081159b4>] __handle_domain_irq+0xac/0xdc [<ffffff9008080e9c>] gic_handle_irq+0x64/0xa4 ... Memory state around the buggy address: ffffffc0601f6400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffffffc0601f6480: 00 00 00 00 00 00 00 00 00 00 06 fc fc fc fc fc >ffffffc0601f6500: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffffffc0601f6580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffffffc0601f6600: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00 ================================================================== Signed-off-by:
William Wu <william.wu@rock-chips.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Jerry Zhang <zhangjerry@google.com> Signed-off-by:
-
Joël Esponde authored
commit 807c1625 upstream. With the S25FL127S nor flash part, each writing to the configuration register takes hundreds of ms. During that time, no more accesses to the flash should be done (even reads). This commit adds a wait loop after the register writing until the flash finishes its work. This issue could make rootfs mounting fail when the latter was done too much closely to this quad enable bit setting step. And in this case, a driver as UBIFS may try to recover the filesystem and may broke it completely. Signed-off-by:
Joël Esponde <joel.esponde@honeywell.com> Signed-off-by:
Cyrille Pitchen <cyrille.pitchen@atmel.com> Signed-off-by:
-
Tobias Wolf authored
commit 3ec75441 upstream. An empty __dtb_start to __dtb_end section might result in initial_boot_params being null for arch/mips/ralink. This showed that the boot process hangs indefinitely in of_scan_flat_dt(). Signed-off-by:
Tobias Wolf <dev-NTEO@vplace.de> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/14605/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
David Howells authored
commit 5f2f9765 upstream. This fixes CVE-2017-7482. When a kerberos 5 ticket is being decoded so that it can be loaded into an rxrpc-type key, there are several places in which the length of a variable-length field is checked to make sure that it's not going to overrun the available data - but the data is padded to the nearest four-byte boundary and the code doesn't check for this extra. This could lead to the size-remaining variable wrapping and the data pointer going over the end of the buffer. Fix this by making the various variable-length data checks use the padded length. Reported-by:
石磊 <shilei-c@360.cn> Signed-off-by:
David Howells <dhowells@redhat.com> Reviewed-by:
Marc Dionne <marc.c.dionne@auristor.com> Reviewed-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Alex Deucher authored
commit 52b482b0 upstream. Increase the default display clock on newer asics to accomodate some high res modes with really high refresh rates. bug: https://bugs.freedesktop.org/show_bug.cgi?id=93826Acked-by:
Chunming Zhou <david1.zhou@amd.com> Acked-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 05b4017b upstream. We were using the wrong structure which lead to an overflow on some boards. bug: https://bugs.freedesktop.org/show_bug.cgi?id=101387Acked-by:
-
Alex Deucher authored
commit acfd6ee4 upstream. Fixes resume from suspend. bug: https://bugzilla.kernel.org/show_bug.cgi?id=196121Reported-by:
Przemek <soprwa@gmail.com> Signed-off-by:
-
Alex Deucher authored
commit 4eb59793 upstream. Disable PX on these systems. bug: https://bugs.freedesktop.org/show_bug.cgi?id=101491Signed-off-by:
-
Nicholas Bellinger authored
commit abb85a9b upstream. When iscsi WRITE underflow occurs there are two different scenarios that can happen. Normally in practice, when an EDTL vs. SCSI CDB TRANSFER LENGTH underflow is detected, the iscsi immediate data payload is the smaller SCSI CDB TRANSFER LENGTH. That is, when a host fabric LLD is using a fixed size EDTL for a specific control CDB, the SCSI CDB TRANSFER LENGTH and actual SCSI payload ends up being smaller than EDTL. In iscsi, this means the received iscsi immediate data payload matches the smaller SCSI CDB TRANSFER LENGTH, because there is no more SCSI payload to accept beyond SCSI CDB TRANSFER LENGTH. However, it's possible for a malicous host to send a WRITE underflow where EDTL is larger than SCSI CDB TRANSFER LENGTH, but incoming iscsi immediate data actually matches EDTL. In the wild, we've never had a iscsi host environment actually try to do this. For this special case, it's wrong to truncate part of the control CDB payload and continue to process the command during underflow when immediate data payload received was larger than SCSI CDB TRANSFER LENGTH, so go ahead and reject and drop the bogus payload as a defensive action. Note this potential bug was originally relaxed by the following for allowing WRITE underflow in MSFT FCP host environments: commit c72c5250 Author: Roland Dreier <roland@purestorage.com> Date: Wed Jul 22 15:08:18 2015 -0700 target: allow underflow/overflow for PR OUT etc. commands Cc: Roland Dreier <roland@purestorage.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Nicholas Bellinger authored
commit 105fa2f4 upstream. This patch fixes a BUG() in iscsit_close_session() that could be triggered when iscsit_logout_post_handler() execution from within tx thread context was not run for more than SECONDS_FOR_LOGOUT_COMP (15 seconds), and the TCP connection didn't already close before then forcing tx thread context to automatically exit. This would manifest itself during explicit logout as: [33206.974254] 1 connection(s) still exist for iSCSI session to iqn.1993-08.org.debian:01:3f5523242179 [33206.980184] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 2100.772 msecs [33209.078643] ------------[ cut here ]------------ [33209.078646] kernel BUG at drivers/target/iscsi/iscsi_target.c:4346! Normally when explicit logout attempt fails, the tx thread context exits and iscsit_close_connection() from rx thread context does the extra cleanup once it detects conn->conn_logout_remove has not been cleared by the logout type specific post handlers. To address this special case, if the logout post handler in tx thread context detects conn->tx_thread_active has already been cleared, simply return and exit in order for existing iscsit_close_connection() logic from rx thread context do failed logout cleanup. Reported-by:
Bart Van Assche <bart.vanassche@sandisk.com> Tested-by:
Gary Guo <ghg@datera.io> Tested-by:
Chu Yuan Lin <cyl@datera.io> Signed-off-by:
-
Nicholas Bellinger authored
commit 73d4e580 upstream. This patch fixes a se_cmd->cmd_kref underflow during CMD_T_ABORTED when a fabric driver drops it's second reference from below the target_core_tmr.c based callers of transport_cmd_finish_abort(). Recently with the conversion of kref to refcount_t, this bug was manifesting itself as: [705519.601034] refcount_t: underflow; use-after-free. [705519.604034] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 20116.512 msecs [705539.719111] ------------[ cut here ]------------ [705539.719117] WARNING: CPU: 3 PID: 26510 at lib/refcount.c:184 refcount_sub_and_test+0x33/0x51 Since the original kref atomic_t based kref_put() didn't check for underflow and only invoked the final callback when zero was reached, this bug did not manifest in practice since all se_cmd memory is using preallocated tags. To address this, go ahead and propigate the existing return from transport_put_cmd() up via transport_cmd_finish_abort(), and change transport_cmd_finish_abort() + core_tmr_handle_tas_abort() callers to only do their local target_put_sess_cmd() if necessary. Reported-by:
-
Will Deacon authored
commit dbb236c1 upstream. Recently vDSO support for CLOCK_MONOTONIC_RAW was added in 49eea433 ("arm64: Add support for CLOCK_MONOTONIC_RAW in clock_gettime() vDSO"). Noticing that the core timekeeping code never set tkr_raw.xtime_nsec, the vDSO implementation didn't bother exposing it via the data page and instead took the unshifted tk->raw_time.tv_nsec value which was then immediately shifted left in the vDSO code. Unfortunately, by accellerating the MONOTONIC_RAW clockid, it uncovered potential 1ns time inconsistencies caused by the timekeeping core not handing sub-ns resolution. Now that the core code has been fixed and is actually setting tkr_raw.xtime_nsec, we need to take that into account in the vDSO by adding it to the shifted raw_time value, in order to fix the user-visible inconsistency. Rather than do that at each use (and expand the data page in the process), instead perform the shift/addition operation when populating the data page and remove the shift from the vDSO code entirely. [jstultz: minor whitespace tweak, tried to improve commit message to make it more clear this fixes a regression] Reported-by:
John Stultz <john.stultz@linaro.org> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Daniel Mentz <danielmentz@google.com> Acked-by:
Kevin Brodsky <kevin.brodsky@arm.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Stephen Boyd <stephen.boyd@linaro.org> Cc: Miroslav Lichvar <mlichvar@redhat.com> Link: http://lkml.kernel.org/r/1496965462-20003-4-git-send-email-john.stultz@linaro.orgSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
John Stultz authored
commit 3d88d56c upstream. Due to how the MONOTONIC_RAW accumulation logic was handled, there is the potential for a 1ns discontinuity when we do accumulations. This small discontinuity has for the most part gone un-noticed, but since ARM64 enabled CLOCK_MONOTONIC_RAW in their vDSO clock_gettime implementation, we've seen failures with the inconsistency-check test in kselftest. This patch addresses the issue by using the same sub-ns accumulation handling that CLOCK_MONOTONIC uses, which avoids the issue for in-kernel users. Since the ARM64 vDSO implementation has its own clock_gettime calculation logic, this patch reduces the frequency of errors, but failures are still seen. The ARM64 vDSO will need to be updated to include the sub-nanosecond xtime_nsec values in its calculation for this issue to be completely fixed. Signed-off-by:
-
John Stultz authored
commit ceea5e37 upstream. In tests, which excercise switching of clocksources, a NULL pointer dereference can be observed on AMR64 platforms in the clocksource read() function: u64 clocksource_mmio_readl_down(struct clocksource *c) { return ~(u64)readl_relaxed(to_mmio_clksrc(c)->reg) & c->mask; } This is called from the core timekeeping code via: cycle_now = tkr->read(tkr->clock); tkr->read is the cached tkr->clock->read() function pointer. When the clocksource is changed then tkr->clock and tkr->read are updated sequentially. The code above results in a sequential load operation of tkr->read and tkr->clock as well. If the store to tkr->clock hits between the loads of tkr->read and tkr->clock, then the old read() function is called with the new clock pointer. As a consequence the read() function dereferences a different data structure and the resulting 'reg' pointer can point anywhere including NULL. This problem was introduced when the timekeeping code was switched over to use struct tk_read_base. Before that, it was theoretically possible as well when the compiler decided to reload clock in the code sequence: now = tk->clock->read(tk->clock); Add a helper function which avoids the issue by reading tk_read_base->clock once into a local variable clk and then issue the read function via clk->read(clk). This guarantees that the read() function always gets the proper clocksource pointer handed in. Since there is now no use for the tkr.read pointer, this patch also removes it, and to address stopping the fast timekeeper during suspend/resume, it introduces a dummy clocksource to use rather then just a dummy read function. Signed-off-by:
Ingo Molnar <mingo@kernel.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Stephen Boyd <stephen.boyd@linaro.org> Cc: Miroslav Lichvar <mlichvar@redhat.com> Cc: Daniel Mentz <danielmentz@google.com> Link: http://lkml.kernel.org/r/1496965462-20003-2-git-send-email-john.stultz@linaro.orgSigned-off-by:
-
Arend Van Spriel authored
commit 7a51461f upstream. When request firmware fails, brcmf_ops_sdio_remove is being called and brcmf_bus freed. In such circumstancies if you do a suspend/resume cycle the kernel hangs on resume due a NULL pointer dereference in resume function. So in brcmf_sdio_firmware_callback() we need to unbind the driver from both sdio_func devices when firmware load failure is indicated. Tested-by:
Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by:
Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by:
Franky Lin <franky.lin@broadcom.com> Signed-off-by:
-
Arend Van Spriel authored
commit 03fb0e83 upstream. When firmware loading failed the code used to unbind the device provided by the calling code. However, for the sdio driver two devices are bound and both need to be released upon failure. The callback has been extended with parameter to pass error code so add that in this commit upon firmware loading failure. Reviewed-by:
-
Arend Van Spriel authored
commit 6d0507a7 upstream. Extend the parameters in the firmware callback so it can be called upon success and failure. This allows the caller to properly clear all resources in the failure path. Right now the error code is always zero, ie. success. Reviewed-by:
-
Daniel Drake authored
commit 817ae460 upstream. Without this quirk, the touchpad is not responsive on this product, with the following message repeated in the logs: psmouse serio1: bad data from KBC - timeout Add it to the notimeout list alongside other similar Fujitsu laptops. Signed-off-by:
Daniel Drake <drake@endlessm.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Naveen N. Rao authored
commit d89ba535 upstream. On Power9, trying to use data breakpoints throws the splat shown below. This is because the check for a data breakpoint in DSISR is in do_hash_page(), which is not called when in Radix mode. Unable to handle kernel paging request for data at address 0xc000000000e19218 Faulting instruction address: 0xc0000000001155e8 cpu 0x0: Vector: 300 (Data Access) at [c0000000ef1e7b20] pc: c0000000001155e8: find_pid_ns+0x48/0xe0 lr: c000000000116ac4: find_task_by_vpid+0x44/0x90 sp: c0000000ef1e7da0 msr: 9000000000009033 dar: c000000000e19218 dsisr: 400000 Move the check to handle_page_fault() so as to catch data breakpoints in both Hash and Radix MMU modes. We have to change the check in do_hash_page() against 0xa410 to use 0xa450, so as to include the value of (DSISR_DABRMATCH << 16). There are two sites that call handle_page_fault() when in Radix, both already pass DSISR in r4. Fixes: caca285e ("powerpc/mm/radix: Use STD_MMU_64 to properly isolate hash related code") Reported-by:
Shriya R. Kulkarni <shriykul@in.ibm.com> Signed-off-by:
Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> [mpe: Fix the fall-through case on hash, we need to reload DSISR] Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Naveen N. Rao authored
commit a9f8553e upstream. This fixes a crash when function_graph and jprobes are used together. This is essentially commit 237d28db ("ftrace/jprobes/x86: Fix conflict between jprobes and function graph tracing"), but for powerpc. Jprobes breaks function_graph tracing since the jprobe hook needs to use jprobe_return(), which never returns back to the hook, but instead to the original jprobe'd function. The solution is to momentarily pause function_graph tracing before invoking the jprobe hook and re-enable it when returning back to the original jprobe'd function. Fixes: 6794c782 ("powerpc64: port of the function graph tracer") Signed-off-by:
Masami Hiramatsu <mhiramat@kernel.org> Acked-by:
-
Eric W. Biederman authored
commit 57db7e4a upstream. Thomas Gleixner wrote: > The CRIU support added a 'feature' which allows a user space task to send > arbitrary (kernel) signals to itself. The changelog says: > > The kernel prevents sending of siginfo with positive si_code, because > these codes are reserved for kernel. I think we can allow a task to > send such a siginfo to itself. This operation should not be dangerous. > > Quite contrary to that claim, it turns out that it is outright dangerous > for signals with info->si_code == SI_TIMER. The following code sequence in > a user space task allows to crash the kernel: > > id = timer_create(CLOCK_XXX, ..... signo = SIGX); > timer_set(id, ....); > info->si_signo = SIGX; > info->si_code = SI_TIMER: > info->_sifields._timer._tid = id; > info->_sifields._timer._sys_private = 2; > rt_[tg]sigqueueinfo(..., SIGX, info); > sigemptyset(&sigset); > sigaddset(&sigset, SIGX); > rt_sigtimedwait(sigset, info); > > For timers based on CLOCK_PROCESS_CPUTIME_ID, CLOCK_THREAD_CPUTIME_ID this > results in a kernel crash because sigwait() dequeues the signal and the > dequeue code observes: > > info->si_code == SI_TIMER && info->_sifields._timer._sys_private != 0 > > which triggers the following callchain: > > do_schedule_next_timer() -> posix_cpu_timer_schedule() -> arm_timer() > > arm_timer() executes a list_add() on the timer, which is already armed via > the timer_set() syscall. That's a double list add which corrupts the posix > cpu timer list. As a consequence the kernel crashes on the next operation > touching the posix cpu timer list. > > Posix clocks which are internally implemented based on hrtimers are not > affected by this because hrtimer_start() can handle already armed timers > nicely, but it's a reliable way to trigger the WARN_ON() in > hrtimer_forward(), which complains about calling that function on an > already armed timer. This problem has existed since the posix timer code was merged into 2.5.63. A few releases earlier in 2.5.60 ptrace gained the ability to inject not just a signal (which linux has supported since 1.0) but the full siginfo of a signal. The core problem is that the code will reschedule in response to signals getting dequeued not just for signals the timers sent but for other signals that happen to a si_code of SI_TIMER. Avoid this confusion by testing to see if the queued signal was preallocated as all timer signals are preallocated, and so far only the timer code preallocates signals. Move the check for if a timer needs to be rescheduled up into collect_signal where the preallocation check must be performed, and pass the result back to dequeue_signal where the code reschedules timers. This makes it clear why the code cares about preallocated timers. Reported-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Sebastian Parschauer authored
commit 3db28271 upstream. This mouse is also known under other IDs. It needs the quirk ALWAYS_POLL or will disconnect in runlevel 1 or 3. Signed-off-by:
Sebastian Parschauer <sparschauer@suse.de> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Raju Rangoju authored
commit dec6b331 upstream. During the module initialisation there is a possible race (basically race between uld and lld) where neither the uld nor lld notifies the uP about where to route the ctrl queue completions. LLD skips notifying uP as the rdma queues were not created by then (will leave it to ULD to notify the uP). As the ULD comes up, it also skips notifying the uP as the flag FULL_INIT_DONE is not set yet (ULD assumes that the interface is not up yet). Consequently, this race between uld and lld leaves uP unnotified about where to send the ctrl queue completions to, leading to iwarp RI_RES WR failure. Here is the race: CPU 0 CPU1 - allocates nic rx queus - t4_sge_alloc_ctrl_txq() (if rdma rsp queues exists, tell uP to route ctrl queue compl to rdma rspq) - acquires the mutex_lock - allocates rdma response queues - if FULL_INIT_DONE set, tell uP to route ctrl queue compl to rdma rspq - relinquishes mutex_lock - acquires the mutex_lock - enable_rx() - set FULL_INIT_DONE - relinquishes mutex_lock This patch fixes the above issue. Fixes: e7519f99('cxgb4: avoid enabling napi twice to the same queue') Signed-off-by:
Raju Rangoju <rajur@chelsio.com> Acked-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by:
-
Pavel Shilovsky authored
commit dcd87838 upstream. Downgrade the loglevel for SMB2 to prevent filling the log with messages if e.g. readdir was interrupted. Also make SMB2 and SMB1 codepaths do the same logging during readdir. Signed-off-by:
Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Paul Mackerras authored
commit ca8efa1d upstream. This adds code to save the values of three SPRs (special-purpose registers) used by userspace to control event-based branches (EBBs), which are essentially interrupts that get delivered directly to userspace. These registers are loaded up with guest values when entering the guest, and their values are saved when exiting the guest, but we were not saving the host values and restoring them before going back to userspace. On POWER8 this would only affect userspace programs which explicitly request the use of EBBs and also use the KVM_RUN ioctl, since the only source of EBBs on POWER8 is the PMU, and there is an explicit enable bit in the PMU registers (and those PMU registers do get properly context-switched between host and guest). On POWER9 there is provision for externally-generated EBBs, and these are not subject to the control in the PMU registers. Since these registers only affect userspace, we can save them when we first come in from userspace and restore them before returning to userspace, rather than saving/restoring the host values on every guest entry/exit. Similarly, we don't need to worry about their values on offline secondary threads since they execute in the context of the idle task, which never executes in userspace. Fixes: b005255e ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08) Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
-
Paul Mackerras authored
commit 46a704f8 upstream. If userspace attempts to call the KVM_RUN ioctl when it has hardware transactional memory (HTM) enabled, the values that it has put in the HTM-related SPRs TFHAR, TFIAR and TEXASR will get overwritten by guest values. To fix this, we detect this condition and save those SPR values in the thread struct, and disable HTM for the task. If userspace goes to access those SPRs or the HTM facility in future, a TM-unavailable interrupt will occur and the handler will reload those SPRs and re-enable HTM. If userspace has started a transaction and suspended it, we would currently lose the transactional state in the guest entry path and would almost certainly get a "TM Bad Thing" interrupt, which would cause the host to crash. To avoid this, we detect this case and return from the KVM_RUN ioctl with an EINVAL error, with the KVM exit reason set to KVM_EXIT_FAIL_ENTRY. Fixes: b005255e ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08) Signed-off-by:
-
Heiko Carstens authored
commit addb63c1 upstream. For real-space designation asces the asce origin part is only a token. The asce token origin must not be used to generate an effective address for storage references. This however is erroneously done within kvm_s390_shadow_tables(). Furthermore within the same function the wrong parts of virtual addresses are used to generate a corresponding real address (e.g. the region second index is used as region first index). Both of the above can result in incorrect address translations. Only for real space designations with a token origin of zero and addresses below one megabyte the translation was correct. Furthermore replace a "!asce.r" statement with a "!*fake" statement to make it more obvious that a specific condition has nothing to do with the architecture, but with the fake handling of real space designations. Fixes: 3218f709 ("s390/mm: support real-space for gmap shadows") Cc: David Hildenbrand <david@redhat.com> Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by:
-
Kan Liang authored
commit fb3a5055 upstream. Current DTLB load/store miss events (0x608/0x649) only counts 4K,2M and 4M page size. Need to extend the events to support any page size (4K/2M/4M/1G). The complete DTLB load/store miss events are: DTLB_LOAD_MISSES.WALK_COMPLETED 0xe08 DTLB_STORE_MISSES.WALK_COMPLETED 0xe49 Signed-off-by:
Kan Liang <Kan.liang@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: eranian@google.com Link: http://lkml.kernel.org/r/20170619142609.11058-1-kan.liang@intel.comSigned-off-by:
-
Ilya Matveychikov authored
commit a91e0f68 upstream. When using get_options() it's possible to specify a range of numbers, like 1-100500. The problem is that it doesn't track array size while calling internally to get_range() which iterates over the range and fills the memory with numbers. Link: http://lkml.kernel.org/r/2613C75C-B04D-4BFF-82A6-12F97BA0F620@gmail.comSigned-off-by:
Ilya V. Matveychikov <matvejchikov@gmail.com> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
NeilBrown authored
commit 9fa4eb8e upstream. If a positive status is passed with the AUTOFS_DEV_IOCTL_FAIL ioctl, autofs4_d_automount() will return ERR_PTR(status) with that status to follow_automount(), which will then dereference an invalid pointer. So treat a positive status the same as zero, and map to ENOENT. See comment in systemd src/core/automount.c::automount_send_ready(). Link: http://lkml.kernel.org/r/871sqwczx5.fsf@notabene.neil.brown.nameSigned-off-by:
NeilBrown <neilb@suse.com> Cc: Ian Kent <raven@themaw.net> Signed-off-by:
-
Ravi Bangoria authored
commit bf05fc25 upstream. When a kthread calls call_usermodehelper() the steps are: 1. allocate current->mm 2. load_elf_binary() 3. populate current->thread.regs While doing this, interrupts are not disabled. If there is a perf interrupt in the middle of this process (i.e. step 1 has completed but not yet reached to step 3) and if perf tries to read userspace regs, kernel oops with following log: Unable to handle kernel paging request for data at address 0x00000000 Faulting instruction address: 0xc0000000000da0fc ... Call Trace: perf_output_sample_regs+0x6c/0xd0 perf_output_sample+0x4e4/0x830 perf_event_output_forward+0x64/0x90 __perf_event_overflow+0x8c/0x1e0 record_and_restart+0x220/0x5c0 perf_event_interrupt+0x2d8/0x4d0 performance_monitor_exception+0x54/0x70 performance_monitor_common+0x158/0x160 --- interrupt: f01 at avtab_search_node+0x150/0x1a0 LR = avtab_search_node+0x100/0x1a0 ... load_elf_binary+0x6e8/0x15a0 search_binary_handler+0xe8/0x290 do_execveat_common.isra.14+0x5f4/0x840 call_usermodehelper_exec_async+0x170/0x210 ret_from_kernel_thread+0x5c/0x7c Fix it by setting abi to PERF_SAMPLE_REGS_ABI_NONE when userspace pt_regs are not set. Fixes: ed4a4ef8 ("powerpc/perf: Add support for sampling interrupt register state") Signed-off-by:
Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Acked-by:
-
Kees Cook authored
commit 98da7d08 upstream. When limiting the argv/envp strings during exec to 1/4 of the stack limit, the storage of the pointers to the strings was not included. This means that an exec with huge numbers of tiny strings could eat 1/4 of the stack limit in strings and then additional space would be later used by the pointers to the strings. For example, on 32-bit with a 8MB stack rlimit, an exec with 1677721 single-byte strings would consume less than 2MB of stack, the max (8MB / 4) amount allowed, but the pointers to the strings would consume the remaining additional stack space (1677721 * 4 == 6710884). The result (1677721 + 6710884 == 8388605) would exhaust stack space entirely. Controlling this stack exhaustion could result in pathological behavior in setuid binaries (CVE-2017-1000365). [akpm@linux-foundation.org: additional commenting from Kees] Fixes: b6a2fea3 ("mm: variable length argument support") Link: http://lkml.kernel.org/r/20170622001720.GA32173@beastSigned-off-by:
Kees Cook <keescook@chromium.org> Acked-by:
Rik van Riel <riel@redhat.com> Acked-by:
Michal Hocko <mhocko@suse.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Qualys Security Advisory <qsa@qualys.com> Signed-off-by:
-
