Commit 2ac294ac authored by PX4BuildBot's avatar PX4BuildBot

autogenerated headers for rev...

autogenerated headers for rev https://github.com/mavlink/mavlink/tree/c5796d16915b0f9125060b0b3c88c79217b8c328
parent 089833dc
...@@ -123,7 +123,7 @@ typedef enum MAV_CMD ...@@ -123,7 +123,7 @@ typedef enum MAV_CMD
MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.| */ MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.| */
MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.| */ MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.| */
MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility. All receivers should ACK the command and then emit their capabilities in an PROTOCOL_VERSION message |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_CAMERA_SETTINGS=522, /* Request camera settings (CAMERA_SETTINGS). |0: No Action 1: Request camera settings| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_CAMERA_SETTINGS=522, /* Request camera settings (CAMERA_SETTINGS). |0: No Action 1: Request camera settings| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
...@@ -142,7 +142,7 @@ typedef enum MAV_CMD ...@@ -142,7 +142,7 @@ typedef enum MAV_CMD
MAV_CMD_DO_GIMBAL_MANAGER_TRACK_RECTANGLE=1002, /* If the gimbal supports visual tracking (GIMBAL_MANAGER_CAP_FLAGS_HAS_TRACKING_RECTANGLE is set), this command allows to initiate the tracking. Such a tracking gimbal manager would usually be an integrated camera/gimbal, or alternatively a companion computer connected to a camera. |Top left corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Top left corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Bottom right corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Bottom right corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Reserved (default:0)| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)| */ MAV_CMD_DO_GIMBAL_MANAGER_TRACK_RECTANGLE=1002, /* If the gimbal supports visual tracking (GIMBAL_MANAGER_CAP_FLAGS_HAS_TRACKING_RECTANGLE is set), this command allows to initiate the tracking. Such a tracking gimbal manager would usually be an integrated camera/gimbal, or alternatively a companion computer connected to a camera. |Top left corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Top left corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Bottom right corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Bottom right corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Reserved (default:0)| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)| */
MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */ MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */
MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURE message. |Sequence number for missing CAMERA_IMAGE_CAPTURE message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */ MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURED message. |Sequence number for missing CAMERA_IMAGE_CAPTURED message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */
MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */ MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */
MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). |Video Stream ID (0 for all streams)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */ MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). |Video Stream ID (0 for all streams)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */
......
...@@ -7,7 +7,7 @@ ...@@ -7,7 +7,7 @@
#ifndef MAVLINK_VERSION_H #ifndef MAVLINK_VERSION_H
#define MAVLINK_VERSION_H #define MAVLINK_VERSION_H
#define MAVLINK_BUILD_DATE "Sat Apr 25 2020" #define MAVLINK_BUILD_DATE "Mon Apr 27 2020"
#define MAVLINK_WIRE_PROTOCOL_VERSION "2.0" #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
#define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
......
...@@ -144,7 +144,7 @@ typedef enum MAV_CMD ...@@ -144,7 +144,7 @@ typedef enum MAV_CMD
MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.| */ MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.| */
MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.| */ MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.| */
MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility. All receivers should ACK the command and then emit their capabilities in an PROTOCOL_VERSION message |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_CAMERA_SETTINGS=522, /* Request camera settings (CAMERA_SETTINGS). |0: No Action 1: Request camera settings| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_CAMERA_SETTINGS=522, /* Request camera settings (CAMERA_SETTINGS). |0: No Action 1: Request camera settings| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
...@@ -163,7 +163,7 @@ typedef enum MAV_CMD ...@@ -163,7 +163,7 @@ typedef enum MAV_CMD
MAV_CMD_DO_GIMBAL_MANAGER_TRACK_RECTANGLE=1002, /* If the gimbal supports visual tracking (GIMBAL_MANAGER_CAP_FLAGS_HAS_TRACKING_RECTANGLE is set), this command allows to initiate the tracking. Such a tracking gimbal manager would usually be an integrated camera/gimbal, or alternatively a companion computer connected to a camera. |Top left corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Top left corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Bottom right corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Bottom right corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Reserved (default:0)| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)| */ MAV_CMD_DO_GIMBAL_MANAGER_TRACK_RECTANGLE=1002, /* If the gimbal supports visual tracking (GIMBAL_MANAGER_CAP_FLAGS_HAS_TRACKING_RECTANGLE is set), this command allows to initiate the tracking. Such a tracking gimbal manager would usually be an integrated camera/gimbal, or alternatively a companion computer connected to a camera. |Top left corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Top left corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Bottom right corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Bottom right corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Reserved (default:0)| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)| */
MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */ MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */
MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURE message. |Sequence number for missing CAMERA_IMAGE_CAPTURE message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */ MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURED message. |Sequence number for missing CAMERA_IMAGE_CAPTURED message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */
MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */ MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */
MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). |Video Stream ID (0 for all streams)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */ MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). |Video Stream ID (0 for all streams)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */
......
...@@ -7,7 +7,7 @@ ...@@ -7,7 +7,7 @@
#ifndef MAVLINK_VERSION_H #ifndef MAVLINK_VERSION_H
#define MAVLINK_VERSION_H #define MAVLINK_VERSION_H
#define MAVLINK_BUILD_DATE "Sat Apr 25 2020" #define MAVLINK_BUILD_DATE "Mon Apr 27 2020"
#define MAVLINK_WIRE_PROTOCOL_VERSION "2.0" #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
#define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
......
...@@ -167,7 +167,7 @@ typedef enum MAV_CMD ...@@ -167,7 +167,7 @@ typedef enum MAV_CMD
MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.| */ MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.| */
MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.| */ MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.| */
MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility. All receivers should ACK the command and then emit their capabilities in an PROTOCOL_VERSION message |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_CAMERA_SETTINGS=522, /* Request camera settings (CAMERA_SETTINGS). |0: No Action 1: Request camera settings| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_CAMERA_SETTINGS=522, /* Request camera settings (CAMERA_SETTINGS). |0: No Action 1: Request camera settings| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
...@@ -186,7 +186,7 @@ typedef enum MAV_CMD ...@@ -186,7 +186,7 @@ typedef enum MAV_CMD
MAV_CMD_DO_GIMBAL_MANAGER_TRACK_RECTANGLE=1002, /* If the gimbal supports visual tracking (GIMBAL_MANAGER_CAP_FLAGS_HAS_TRACKING_RECTANGLE is set), this command allows to initiate the tracking. Such a tracking gimbal manager would usually be an integrated camera/gimbal, or alternatively a companion computer connected to a camera. |Top left corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Top left corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Bottom right corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Bottom right corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Reserved (default:0)| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)| */ MAV_CMD_DO_GIMBAL_MANAGER_TRACK_RECTANGLE=1002, /* If the gimbal supports visual tracking (GIMBAL_MANAGER_CAP_FLAGS_HAS_TRACKING_RECTANGLE is set), this command allows to initiate the tracking. Such a tracking gimbal manager would usually be an integrated camera/gimbal, or alternatively a companion computer connected to a camera. |Top left corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Top left corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Bottom right corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Bottom right corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Reserved (default:0)| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)| */
MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */ MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */
MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURE message. |Sequence number for missing CAMERA_IMAGE_CAPTURE message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */ MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURED message. |Sequence number for missing CAMERA_IMAGE_CAPTURED message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */
MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */ MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */
MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). |Video Stream ID (0 for all streams)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */ MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). |Video Stream ID (0 for all streams)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */
......
...@@ -7,7 +7,7 @@ ...@@ -7,7 +7,7 @@
#ifndef MAVLINK_VERSION_H #ifndef MAVLINK_VERSION_H
#define MAVLINK_VERSION_H #define MAVLINK_VERSION_H
#define MAVLINK_BUILD_DATE "Sat Apr 25 2020" #define MAVLINK_BUILD_DATE "Mon Apr 27 2020"
#define MAVLINK_WIRE_PROTOCOL_VERSION "2.0" #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
#define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
......
...@@ -743,7 +743,7 @@ typedef enum MAV_CMD ...@@ -743,7 +743,7 @@ typedef enum MAV_CMD
MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.| */ MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.| */
MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.| */ MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.| */
MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility. All receivers should ACK the command and then emit their capabilities in an PROTOCOL_VERSION message |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_CAMERA_SETTINGS=522, /* Request camera settings (CAMERA_SETTINGS). |0: No Action 1: Request camera settings| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_CAMERA_SETTINGS=522, /* Request camera settings (CAMERA_SETTINGS). |0: No Action 1: Request camera settings| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
...@@ -762,7 +762,7 @@ typedef enum MAV_CMD ...@@ -762,7 +762,7 @@ typedef enum MAV_CMD
MAV_CMD_DO_GIMBAL_MANAGER_TRACK_RECTANGLE=1002, /* If the gimbal supports visual tracking (GIMBAL_MANAGER_CAP_FLAGS_HAS_TRACKING_RECTANGLE is set), this command allows to initiate the tracking. Such a tracking gimbal manager would usually be an integrated camera/gimbal, or alternatively a companion computer connected to a camera. |Top left corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Top left corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Bottom right corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Bottom right corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Reserved (default:0)| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)| */ MAV_CMD_DO_GIMBAL_MANAGER_TRACK_RECTANGLE=1002, /* If the gimbal supports visual tracking (GIMBAL_MANAGER_CAP_FLAGS_HAS_TRACKING_RECTANGLE is set), this command allows to initiate the tracking. Such a tracking gimbal manager would usually be an integrated camera/gimbal, or alternatively a companion computer connected to a camera. |Top left corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Top left corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Bottom right corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Bottom right corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Reserved (default:0)| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)| */
MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */ MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */
MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURE message. |Sequence number for missing CAMERA_IMAGE_CAPTURE message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */ MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURED message. |Sequence number for missing CAMERA_IMAGE_CAPTURED message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */
MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */ MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */
MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). |Video Stream ID (0 for all streams)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */ MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). |Video Stream ID (0 for all streams)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */
...@@ -1472,7 +1472,7 @@ typedef enum CAMERA_CAP_FLAGS ...@@ -1472,7 +1472,7 @@ typedef enum CAMERA_CAP_FLAGS
CAMERA_CAP_FLAGS_HAS_IMAGE_SURVEY_MODE=32, /* Camera has image survey mode (MAV_CMD_SET_CAMERA_MODE) | */ CAMERA_CAP_FLAGS_HAS_IMAGE_SURVEY_MODE=32, /* Camera has image survey mode (MAV_CMD_SET_CAMERA_MODE) | */
CAMERA_CAP_FLAGS_HAS_BASIC_ZOOM=64, /* Camera has basic zoom control (MAV_CMD_SET_CAMERA_ZOOM) | */ CAMERA_CAP_FLAGS_HAS_BASIC_ZOOM=64, /* Camera has basic zoom control (MAV_CMD_SET_CAMERA_ZOOM) | */
CAMERA_CAP_FLAGS_HAS_BASIC_FOCUS=128, /* Camera has basic focus control (MAV_CMD_SET_CAMERA_FOCUS) | */ CAMERA_CAP_FLAGS_HAS_BASIC_FOCUS=128, /* Camera has basic focus control (MAV_CMD_SET_CAMERA_FOCUS) | */
CAMERA_CAP_FLAGS_HAS_VIDEO_STREAM=256, /* Camera has video streaming capabilities (use MAV_CMD_REQUEST_VIDEO_STREAM_INFORMATION for video streaming info) | */ CAMERA_CAP_FLAGS_HAS_VIDEO_STREAM=256, /* Camera has video streaming capabilities (request VIDEO_STREAM_INFORMATION with MAV_CMD_REQUEST_MESSAGE for video streaming info) | */
CAMERA_CAP_FLAGS_ENUM_END=257, /* | */ CAMERA_CAP_FLAGS_ENUM_END=257, /* | */
} CAMERA_CAP_FLAGS; } CAMERA_CAP_FLAGS;
#endif #endif
......
...@@ -7,7 +7,7 @@ ...@@ -7,7 +7,7 @@
#ifndef MAVLINK_VERSION_H #ifndef MAVLINK_VERSION_H
#define MAVLINK_VERSION_H #define MAVLINK_VERSION_H
#define MAVLINK_BUILD_DATE "Sat Apr 25 2020" #define MAVLINK_BUILD_DATE "Mon Apr 27 2020"
#define MAVLINK_WIRE_PROTOCOL_VERSION "2.0" #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
#define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
......
...@@ -7,7 +7,7 @@ ...@@ -7,7 +7,7 @@
#ifndef MAVLINK_VERSION_H #ifndef MAVLINK_VERSION_H
#define MAVLINK_VERSION_H #define MAVLINK_VERSION_H
#define MAVLINK_BUILD_DATE "Sat Apr 25 2020" #define MAVLINK_BUILD_DATE "Mon Apr 27 2020"
#define MAVLINK_WIRE_PROTOCOL_VERSION "2.0" #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
#define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
......
...@@ -140,7 +140,7 @@ typedef enum MAV_CMD ...@@ -140,7 +140,7 @@ typedef enum MAV_CMD
MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.| */ MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.| */
MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.| */ MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.| */
MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility. All receivers should ACK the command and then emit their capabilities in an PROTOCOL_VERSION message |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_CAMERA_SETTINGS=522, /* Request camera settings (CAMERA_SETTINGS). |0: No Action 1: Request camera settings| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_CAMERA_SETTINGS=522, /* Request camera settings (CAMERA_SETTINGS). |0: No Action 1: Request camera settings| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
...@@ -159,7 +159,7 @@ typedef enum MAV_CMD ...@@ -159,7 +159,7 @@ typedef enum MAV_CMD
MAV_CMD_DO_GIMBAL_MANAGER_TRACK_RECTANGLE=1002, /* If the gimbal supports visual tracking (GIMBAL_MANAGER_CAP_FLAGS_HAS_TRACKING_RECTANGLE is set), this command allows to initiate the tracking. Such a tracking gimbal manager would usually be an integrated camera/gimbal, or alternatively a companion computer connected to a camera. |Top left corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Top left corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Bottom right corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Bottom right corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Reserved (default:0)| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)| */ MAV_CMD_DO_GIMBAL_MANAGER_TRACK_RECTANGLE=1002, /* If the gimbal supports visual tracking (GIMBAL_MANAGER_CAP_FLAGS_HAS_TRACKING_RECTANGLE is set), this command allows to initiate the tracking. Such a tracking gimbal manager would usually be an integrated camera/gimbal, or alternatively a companion computer connected to a camera. |Top left corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Top left corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Bottom right corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Bottom right corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Reserved (default:0)| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)| */
MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */ MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */
MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURE message. |Sequence number for missing CAMERA_IMAGE_CAPTURE message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */ MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURED message. |Sequence number for missing CAMERA_IMAGE_CAPTURED message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */
MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */ MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */
MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). |Video Stream ID (0 for all streams)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */ MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). |Video Stream ID (0 for all streams)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */
......
...@@ -7,7 +7,7 @@ ...@@ -7,7 +7,7 @@
#ifndef MAVLINK_VERSION_H #ifndef MAVLINK_VERSION_H
#define MAVLINK_VERSION_H #define MAVLINK_VERSION_H
#define MAVLINK_BUILD_DATE "Sat Apr 25 2020" #define MAVLINK_BUILD_DATE "Mon Apr 27 2020"
#define MAVLINK_WIRE_PROTOCOL_VERSION "2.0" #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
#define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
......
This diff is collapsed.
...@@ -615,7 +615,13 @@ ...@@ -615,7 +615,13 @@
</enum> </enum>
<enum name="MAV_CMD"> <enum name="MAV_CMD">
<description>Commands to be executed by the MAV. They can be executed on user request, or as part of a mission script. If the action is used in a mission, the parameter mapping to the waypoint/mission message is as follows: Param 1, Param 2, Param 3, Param 4, X: Param 5, Y:Param 6, Z:Param 7. This command list is similar what ARINC 424 is for commercial aircraft: A data format how to interpret waypoint/mission data. See https://mavlink.io/en/guide/xml_schema.html#MAV_CMD for information about the structure of the MAV_CMD entries</description> <description>Commands to be executed by the MAV. They can be executed on user request, or as part of a mission script. If the action is used in a mission, the parameter mapping to the waypoint/mission message is as follows: Param 1, Param 2, Param 3, Param 4, X: Param 5, Y:Param 6, Z:Param 7. This command list is similar what ARINC 424 is for commercial aircraft: A data format how to interpret waypoint/mission data. See https://mavlink.io/en/guide/xml_schema.html#MAV_CMD for information about the structure of the MAV_CMD entries</description>
<entry value="512" name="MAV_CMD_REQUEST_MESSAGE" hasLocation="false" isDestination="false">
<description>Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL).</description>
<param index="1" label="Message ID" minValue="0" maxValue="16777215" increment="1">The MAVLink message ID of the requested message.</param>
<param index="2" label="Index ID" minValue="0" increment="1">Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.</param>
</entry>
<entry value="519" name="MAV_CMD_REQUEST_PROTOCOL_VERSION" hasLocation="false" isDestination="false"> <entry value="519" name="MAV_CMD_REQUEST_PROTOCOL_VERSION" hasLocation="false" isDestination="false">
<deprecated since="2019-08" replaced_by="MAV_CMD_REQUEST_MESSAGE"/>
<description>Request MAVLink protocol version compatibility</description> <description>Request MAVLink protocol version compatibility</description>
<param index="1" label="Protocol">1: Request supported protocol versions by all nodes on the network</param> <param index="1" label="Protocol">1: Request supported protocol versions by all nodes on the network</param>
<param index="2">Reserved (all remaining params)</param> <param index="2">Reserved (all remaining params)</param>
......
...@@ -291,6 +291,7 @@ typedef enum MAV_COMPONENT ...@@ -291,6 +291,7 @@ typedef enum MAV_COMPONENT
#define HAVE_ENUM_MAV_CMD #define HAVE_ENUM_MAV_CMD
typedef enum MAV_CMD typedef enum MAV_CMD
{ {
MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_ENUM_END=520, /* | */ MAV_CMD_ENUM_END=520, /* | */
} MAV_CMD; } MAV_CMD;
......
...@@ -7,7 +7,7 @@ ...@@ -7,7 +7,7 @@
#ifndef MAVLINK_VERSION_H #ifndef MAVLINK_VERSION_H
#define MAVLINK_VERSION_H #define MAVLINK_VERSION_H
#define MAVLINK_BUILD_DATE "Sat Apr 25 2020" #define MAVLINK_BUILD_DATE "Mon Apr 27 2020"
#define MAVLINK_WIRE_PROTOCOL_VERSION "2.0" #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
#define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 22 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 22
......
...@@ -123,7 +123,7 @@ typedef enum MAV_CMD ...@@ -123,7 +123,7 @@ typedef enum MAV_CMD
MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.| */ MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.| */
MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.| */ MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.| */
MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility. All receivers should ACK the command and then emit their capabilities in an PROTOCOL_VERSION message |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_REQUEST_CAMERA_SETTINGS=522, /* Request camera settings (CAMERA_SETTINGS). |0: No Action 1: Request camera settings| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_REQUEST_CAMERA_SETTINGS=522, /* Request camera settings (CAMERA_SETTINGS). |0: No Action 1: Request camera settings| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
...@@ -142,7 +142,7 @@ typedef enum MAV_CMD ...@@ -142,7 +142,7 @@ typedef enum MAV_CMD
MAV_CMD_DO_GIMBAL_MANAGER_TRACK_RECTANGLE=1002, /* If the gimbal supports visual tracking (GIMBAL_MANAGER_CAP_FLAGS_HAS_TRACKING_RECTANGLE is set), this command allows to initiate the tracking. Such a tracking gimbal manager would usually be an integrated camera/gimbal, or alternatively a companion computer connected to a camera. |Top left corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Top left corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Bottom right corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Bottom right corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Reserved (default:0)| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)| */ MAV_CMD_DO_GIMBAL_MANAGER_TRACK_RECTANGLE=1002, /* If the gimbal supports visual tracking (GIMBAL_MANAGER_CAP_FLAGS_HAS_TRACKING_RECTANGLE is set), this command allows to initiate the tracking. Such a tracking gimbal manager would usually be an integrated camera/gimbal, or alternatively a companion computer connected to a camera. |Top left corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Top left corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Bottom right corner of rectangle x value (normalized 0..1, 0 is left, 1 is right).| Bottom right corner of rectangle y value (normalized 0..1, 0 is top, 1 is bottom).| Reserved (default:0)| Reserved (default:0)| Component ID of gimbal device to address (or 1-6 for non-MAVLink gimbal), 0 for all gimbal device components. (Send command multiple times for more than one but not all gimbals.)| */
MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence. Sends CAMERA_IMAGE_CAPTURED after each capture. Use NaN for reserved values. |Reserved (Set to 0)| Desired elapsed time between two consecutive pictures (in seconds). Minimum values depend on hardware (typically greater than 2 seconds).| Total number of images to capture. 0 to capture forever/until MAV_CMD_IMAGE_STOP_CAPTURE.| Capture sequence number starting from 1. This is only valid for single-capture (param3 == 1). Increment the capture ID for each capture command to prevent double captures when a command is re-transmitted. Use 0 to ignore it.| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */ MAV_CMD_IMAGE_STOP_CAPTURE=2001, /* Stop image capture sequence Use NaN for reserved values. |Reserved (Set to 0)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */
MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURE message. |Sequence number for missing CAMERA_IMAGE_CAPTURE message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */ MAV_CMD_REQUEST_CAMERA_IMAGE_CAPTURE=2002, /* Re-request a CAMERA_IMAGE_CAPTURED message. |Sequence number for missing CAMERA_IMAGE_CAPTURED message| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:0)| Reserved (default:0)| Reserved (default:NaN)| */
MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */ MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start), -1 to ignore| 1 to reset the trigger sequence, -1 or 0 to ignore| 1 to pause triggering, but without switching the camera off or retracting it. -1 to ignore| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| */
MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */ MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture (recording). |Video Stream ID (0 for all streams)| Frequency CAMERA_CAPTURE_STATUS messages should be sent while recording (0 for no messages, otherwise frequency)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */
MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). |Video Stream ID (0 for all streams)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */ MAV_CMD_VIDEO_STOP_CAPTURE=2501, /* Stop the current video capture (recording). |Video Stream ID (0 for all streams)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| Reserved (default:NaN)| */
......
...@@ -7,7 +7,7 @@ ...@@ -7,7 +7,7 @@
#ifndef MAVLINK_VERSION_H #ifndef MAVLINK_VERSION_H
#define MAVLINK_VERSION_H #define MAVLINK_VERSION_H
#define MAVLINK_BUILD_DATE "Sat Apr 25 2020" #define MAVLINK_BUILD_DATE "Mon Apr 27 2020"
#define MAVLINK_WIRE_PROTOCOL_VERSION "2.0" #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
#define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
......
...@@ -7,7 +7,7 @@ ...@@ -7,7 +7,7 @@
#ifndef MAVLINK_VERSION_H #ifndef MAVLINK_VERSION_H
#define MAVLINK_VERSION_H #define MAVLINK_VERSION_H
#define MAVLINK_BUILD_DATE "Sat Apr 25 2020" #define MAVLINK_BUILD_DATE "Mon Apr 27 2020"
#define MAVLINK_WIRE_PROTOCOL_VERSION "2.0" #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
#define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
......
...@@ -7,7 +7,7 @@ ...@@ -7,7 +7,7 @@
#ifndef MAVLINK_VERSION_H #ifndef MAVLINK_VERSION_H
#define MAVLINK_VERSION_H #define MAVLINK_VERSION_H
#define MAVLINK_BUILD_DATE "Sat Apr 25 2020" #define MAVLINK_BUILD_DATE "Mon Apr 27 2020"
#define MAVLINK_WIRE_PROTOCOL_VERSION "2.0" #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
#define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 179 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 179
......
...@@ -7,7 +7,7 @@ ...@@ -7,7 +7,7 @@
#ifndef MAVLINK_VERSION_H #ifndef MAVLINK_VERSION_H
#define MAVLINK_VERSION_H #define MAVLINK_VERSION_H
#define MAVLINK_BUILD_DATE "Sat Apr 25 2020" #define MAVLINK_BUILD_DATE "Mon Apr 27 2020"
#define MAVLINK_WIRE_PROTOCOL_VERSION "2.0" #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
#define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment