Commit 08d13c70 authored by Olof Johansson's avatar Olof Johansson

Merge tag 'sunxi-dt64-for-4.13' of...

Merge tag 'sunxi-dt64-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64

Allwinner arm64 DT changes for 4.13

Our usual arm64 changes. The most notable things are the EMAC support and
USB support enhancements. There's also support for the SoPine SoM, and the
OrangePi Win.

* tag 'sunxi-dt64-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  arm64: allwinner: a64: Add initial Orangepi Win/WinPlus support
  arm64: allwinner: a64: add device tree for SoPine with baseboard
  arm64: allwinner: bananapi-m64: Enable dwmac-sun8i
  arm64: allwinner: pine64-plus: Enable dwmac-sun8i
  arm64: allwinner: pine64: Enable dwmac-sun8i
  arm64: allwinner: sun50i-a64: add dwmac-sun8i Ethernet driver
  arm64: allwinner: sun50i-a64: Add dt node for the syscon control module
  arm64: allwinner: a64: add DTSI file for SoPine SoM
  arm64: allwinner: a64: Convert CCU raw number references to macros
  arm64: dts: allwinner: pine64: Prepare optional UART nodes with pinctrl
  arm64: allwinner: a64: enable RSB on A64
  arm64: dts: allwinner: pine64: Add remaining UART aliases
  arm64: dts: allwinner: a64: Add UART2 pin nodes
  arm64: allwinner: a64: enable EHCI0/OHCI0 for Pine64
  arm64: allwinner: a64: add EHCI0/OHCI0 nodes to A64 DTSI
Signed-off-by: default avatarOlof Johansson <olof@lixom.net>
parents 0fd5e852 bdecc9cb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
always := $(dtb-y)
......
......@@ -67,6 +67,14 @@ reg_vcc3v3: vcc3v3 {
};
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins>;
phy-mode = "rgmii";
phy-handle = <&ext_rgmii_phy>;
status = "okay";
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
......@@ -77,6 +85,13 @@ &i2c1_pins {
bias-pull-up;
};
&mdio {
ext_rgmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
......
/*
* Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun50i-a64.dtsi"
#include <dt-bindings/gpio/gpio.h>
/ {
model = "OrangePi Win/Win Plus";
compatible = "xunlong,orangepi-win", "allwinner,sun50i-a64";
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
reg_vcc3v3: vcc3v3 {
compatible = "regulator-fixed";
regulator-name = "vcc3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
};
&ehci1 {
status = "okay";
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <&reg_vcc3v3>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
cd-inverted;
status = "okay";
};
&ohci1 {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&usbphy {
status = "okay";
};
......@@ -46,5 +46,20 @@ / {
model = "Pine64+";
compatible = "pine64,pine64-plus", "allwinner,sun50i-a64";
/* TODO: Camera, Ethernet PHY, touchscreen, etc. */
/* TODO: Camera, touchscreen, etc. */
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins>;
phy-mode = "rgmii";
phy-handle = <&ext_rgmii_phy>;
status = "okay";
};
&mdio {
ext_rgmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
};
......@@ -52,6 +52,10 @@ / {
aliases {
serial0 = &uart0;
serial1 = &uart1;
serial2 = &uart2;
serial3 = &uart3;
serial4 = &uart4;
};
chosen {
......@@ -66,10 +70,23 @@ reg_vcc3v3: vcc3v3 {
};
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&rmii_pins>;
phy-mode = "rmii";
phy-handle = <&ext_rmii_phy1>;
status = "okay";
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
......@@ -80,6 +97,13 @@ &i2c1_pins {
bias-pull-up;
};
&mdio {
ext_rmii_phy1: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
......@@ -91,16 +115,49 @@ &mmc0 {
status = "okay";
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
/* On Exp and Euler connectors */
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
/* On Wifi/BT connector, with RTS/CTS */
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
status = "disabled";
};
/* On Pi-2 connector */
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
status = "disabled";
};
/* On Euler connector */
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
status = "disabled";
};
/* On Euler connector, RTS/CTS optional */
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins>;
status = "disabled";
};
&usb_otg {
dr_mode = "host";
status = "okay";
......
/*
* Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.xyz>
*
* Based on sun50i-a64-pine64.dts, which is:
* Copyright (c) 2016 ARM Ltd.
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun50i-a64-sopine.dtsi"
/ {
model = "SoPine with baseboard";
compatible = "pine64,sopine-baseboard", "pine64,sopine",
"allwinner,sun50i-a64";
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
reg_vcc1v8: vcc1v8 {
compatible = "regulator-fixed";
regulator-name = "vcc1v8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins>;
phy-mode = "rgmii";
phy-handle = <&ext_rgmii_phy>;
status = "okay";
};
&mdio {
ext_rgmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
vmmc-supply = <&reg_vcc3v3>;
vqmmc-supply = <&reg_vcc1v8>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
status = "okay";
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&usb_otg {
dr_mode = "host";
status = "okay";
};
&usbphy {
status = "okay";
};
/*
* Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.xyz>
*
* Based on sun50i-a64-pine64.dts, which is:
* Copyright (c) 2016 ARM Ltd.
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include "sun50i-a64.dtsi"
/ {
reg_vcc3v3: vcc3v3 {
compatible = "regulator-fixed";
regulator-name = "vcc3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <&reg_vcc3v3>;
non-removable;
disable-wp;
bus-width = <4>;
status = "okay";
};
......@@ -43,6 +43,7 @@
*/
#include <dt-bindings/clock/sun50i-a64-ccu.h>
#include <dt-bindings/clock/sun8i-r-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/reset/sun50i-a64-ccu.h>
......@@ -129,6 +130,12 @@ soc {
#size-cells = <1>;
ranges;
syscon: syscon@1c00000 {
compatible = "allwinner,sun50i-a64-system-controller",
"syscon";
reg = <0x01c00000 0x1000>;
};
mmc0: mmc@1c0f000 {
compatible = "allwinner,sun50i-a64-mmc";
reg = <0x01c0f000 0x1000>;
......@@ -204,6 +211,28 @@ usbphy: phy@01c19400 {
#phy-cells = <1>;
};
ehci0: usb@01c1a000 {
compatible = "allwinner,sun50i-a64-ehci", "generic-ehci";
reg = <0x01c1a000 0x100>;
interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_OHCI0>,
<&ccu CLK_BUS_EHCI0>,
<&ccu CLK_USB_OHCI0>;
resets = <&ccu RST_BUS_OHCI0>,
<&ccu RST_BUS_EHCI0>;
status = "disabled";
};
ohci0: usb@01c1a400 {
compatible = "allwinner,sun50i-a64-ohci", "generic-ohci";
reg = <0x01c1a400 0x100>;
interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_OHCI0>,
<&ccu CLK_USB_OHCI0>;
resets = <&ccu RST_BUS_OHCI0>;
status = "disabled";
};
ehci1: usb@01c1b000 {
compatible = "allwinner,sun50i-a64-ehci", "generic-ehci";
reg = <0x01c1b000 0x100>;
......@@ -281,6 +310,21 @@ mmc2_pins: mmc2-pins {
bias-pull-up;
};
rmii_pins: rmii_pins {
pins = "PD10", "PD11", "PD13", "PD14", "PD17",
"PD18", "PD19", "PD20", "PD22", "PD23";
function = "emac";
drive-strength = <40>;
};
rgmii_pins: rgmii_pins {
pins = "PD8", "PD9", "PD10", "PD11", "PD12",
"PD13", "PD15", "PD16", "PD17", "PD18",
"PD19", "PD20", "PD21", "PD22", "PD23";
function = "emac";
drive-strength = <40>;
};
uart0_pins_a: uart0@0 {
pins = "PB8", "PB9";
function = "uart0";
......@@ -295,6 +339,26 @@ uart1_rts_cts_pins: uart1_rts_cts_pins {
pins = "PG8", "PG9";
function = "uart1";
};
uart2_pins: uart2-pins {
pins = "PB0", "PB1";
function = "uart2";
};
uart3_pins: uart3-pins {
pins = "PD0", "PD1";
function = "uart3";
};
uart4_pins: uart4-pins {
pins = "PD2", "PD3";
function = "uart4";
};
uart4_rts_cts_pins: uart4-rts-cts-pins {
pins = "PD4", "PD5";
function = "uart4";
};
};
uart0: serial@1c28000 {
......@@ -303,8 +367,8 @@ uart0: serial@1c28000 {
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu 67>;
resets = <&ccu 46>;
clocks = <&ccu CLK_BUS_UART0>;
resets = <&ccu RST_BUS_UART0>;
status = "disabled";
};
......@@ -314,8 +378,8 @@ uart1: serial@1c28400 {
interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu 68>;
resets = <&ccu 47>;
clocks = <&ccu CLK_BUS_UART1>;
resets = <&ccu RST_BUS_UART1>;
status = "disabled";
};
......@@ -325,8 +389,8 @@ uart2: serial@1c28800 {
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu 69>;
resets = <&ccu 48>;
clocks = <&ccu CLK_BUS_UART2>;
resets = <&ccu RST_BUS_UART2>;
status = "disabled";
};
......@@ -336,8 +400,8 @@ uart3: serial@1c28c00 {
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu 70>;
resets = <&ccu 49>;
clocks = <&ccu CLK_BUS_UART3>;
resets = <&ccu RST_BUS_UART3>;
status = "disabled";
};
......@@ -347,8 +411,8 @@ uart4: serial@1c29000 {
interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu 71>;
resets = <&ccu 50>;
clocks = <&ccu CLK_BUS_UART4>;
resets = <&ccu RST_BUS_UART4>;
status = "disabled";
};
......@@ -356,8 +420,8 @@ i2c0: i2c@1c2ac00 {
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2ac00 0x400>;
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu 63>;
resets = <&ccu 42>;
clocks = <&ccu CLK_BUS_I2C0>;
resets = <&ccu RST_BUS_I2C0>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
......@@ -367,8 +431,8 @@ i2c1: i2c@1c2b000 {
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b000 0x400>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu 64>;
resets = <&ccu 43>;
clocks = <&ccu CLK_BUS_I2C1>;
resets = <&ccu RST_BUS_I2C1>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
......@@ -378,11 +442,31 @@ i2c2: i2c@1c2b400 {
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b400 0x400>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu 65>;
resets = <&ccu 44>;
clocks = <&ccu CLK_BUS_I2C2>;
resets = <&ccu RST_BUS_I2C2>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
emac: ethernet@1c30000 {
compatible = "allwinner,sun50i-a64-emac";
syscon = <&syscon>;
reg = <0x01c30000 0x100>;
interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
resets = <&ccu RST_BUS_EMAC>;
reset-names = "stmmaceth";
clocks = <&ccu CLK_BUS_EMAC>;
clock-names = "stmmaceth";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
mdio: mdio {
#address-cells = <1>;
#size-cells = <0>;
};
};
gic: interrupt-controller@1c81000 {
......@@ -416,12 +500,31 @@ r_pio: pinctrl@01f02c00 {
compatible = "allwinner,sun50i-a64-r-pinctrl";
reg = <0x01f02c00 0x400>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&r_ccu 3>, <&osc24M>, <&osc32k>;
clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>, <&osc32k>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
#gpio-cells = <3>;
interrupt-controller;
#interrupt-cells = <3>;
r_rsb_pins: rsb@0 {
pins = "PL0", "PL1";
function = "s_rsb";
};
};
r_rsb: rsb@1f03400 {
compatible = "allwinner,sun8i-a23-rsb";
reg = <0x01f03400 0x400>;
interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&r_ccu 6>;
clock-frequency = <3000000>;
resets = <&r_ccu 2>;
pinctrl-names = "default";
pinctrl-0 = <&r_rsb_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment