Commit c76b78d8 authored by Archit Taneja's avatar Archit Taneja Committed by Brian Norris

mtd: nand: Qualcomm NAND controller driver

The Qualcomm NAND controller is found in SoCs like IPQ806x, MSM7xx,
MDM9x15 series.

It exists as a sub block inside the IPs EBI2 (External Bus Interface 2)
and QPIC (Qualcomm Parallel Interface Controller). These IPs provide a
broader interface for external slow peripheral devices such as LCD and
NAND/NOR flash memory or SRAM like interfaces.

We add support for the NAND controller found within EBI2. For the SoCs
of our interest, we only use the NAND controller within EBI2. Therefore,
it's safe for us to assume that the NAND controller is a standalone block
within the SoC.

The controller supports 512B, 2kB, 4kB and 8kB page 8-bit and 16-bit NAND
flash devices. It contains a HW ECC block that supports BCH ECC (4, 8 and
16 bit correction/step) and RS ECC(4 bit correction/step) that covers main
and spare data. The controller contains an internal 512 byte page buffer
to which we read/write via DMA. The EBI2 type NAND controller uses ADM DMA
for register read/write and data transfers. The controller performs page
reads and writes at a codeword/step level of 512 bytes. It can support up
to 2 external chips of different configurations.

The driver prepares register read and write configuration descriptors for
each codeword, followed by data descriptors to read or write data from the
controller's internal buffer. It uses a single ADM DMA channel that we get
via dmaengine API. The controller requires 2 ADM CRCIs for command and
data flow control. These are passed via DT.

The ecc layout used by the controller is syndrome like, but we can't use
the standard syndrome ecc ops because of several reasons. First, the amount
of data bytes covered by ecc isn't same in each step. Second, writing to
free oob space requires us writing to the entire step in which the oob
lies. This forces us to create our own ecc ops.

One more difference is how the controller accesses the bad block marker.
The controller ignores reading the marker when ECC is enabled. ECC needs
to be explicity disabled to read or write to the bad block marker. The
nand_bbt helpers library hence can't access BBMs for the controller.
For now, we skip the creation of BBT and populate chip->block_bad and
chip->block_markbad helpers instead.
Reviewed-by: default avatarAndy Gross <agross@codeaurora.org>
Signed-off-by: default avatarStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: default avatarArchit Taneja <architt@codeaurora.org>
Reviewed-by: default avatarBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: default avatarBrian Norris <computersforpeace@gmail.com>
parent 438524c6
......@@ -556,4 +556,11 @@ config MTD_NAND_HISI504
help
Enables support for NAND controller on Hisilicon SoC Hip04.
config MTD_NAND_QCOM
tristate "Support for NAND on QCOM SoCs"
depends on ARCH_QCOM
help
Enables support for NAND flash chips on SoCs containing the EBI2 NAND
controller. This controller is found on IPQ806x SoC.
endif # MTD_NAND
......@@ -56,5 +56,6 @@ obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH) += bcm47xxnflash/
obj-$(CONFIG_MTD_NAND_SUNXI) += sunxi_nand.o
obj-$(CONFIG_MTD_NAND_HISI504) += hisi504_nand.o
obj-$(CONFIG_MTD_NAND_BRCMNAND) += brcmnand/
obj-$(CONFIG_MTD_NAND_QCOM) += qcom_nandc.o
nand-objs := nand_base.o nand_bbt.o nand_timings.o
This diff is collapsed.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment