- 23 Nov, 2018 40 commits
-
-
Ricardo Ribalda Delgado authored
Documentation and code was linking the old documentation at: http://v4l2spec.bytesex.org/spec/x1904.htmSigned-off-by:
Ricardo Ribalda Delgado <ricardo@ribalda.com> Signed-off-by:
Hans Verkuil <hansverk@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
kbuild test robot authored
drivers/staging/media/sunxi/cedrus/cedrus.c:421:3-8: No need to set .owner here. The core will do it. Remove .owner field if calls are used which set it automatically Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci Fixes: 50e76151 ("media: platform: Add Cedrus VPU decoder driver") CC: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by:
kbuild test robot <fengguang.wu@intel.com> Acked-by:
Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
-
Jacopo Mondi authored
The R-Car CSI-2 interface has a number of selectable 'channels' that provides pixel data to the VINs during image acquisition. Each channel can be used to match a CSI-2 data type and a CSI-2 virtual channel to be routed to output path. Different SoCs have different number of channels, with R-Car E3 being the notable exception supporting only 2 of them. Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by:
-
Jacopo Mondi authored
Update PHTW tables for V3M and E3 SoCs to the latest datasheet release (R-Car Series, 3rd Generation manual rev1.00 20181017). Signed-off-by:
-
Jacopo Mondi authored
Add support for R-Car E3 R8A77965 to R-Car CSI-2 driver. Based on the experimental patch from Magnus Damm. Signed-off-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by:
-
Jacopo Mondi authored
Add compatible string for R-Car E3 R8A77990 to the list of supported SoCs. Signed-off-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Simon Horman <horms+renesas@verge.net.au> Reviewed-by:
-
Jacopo Mondi authored
Add R-Car E3 R8A77990 SoC to the rcar-vin supported ones. Based on the experimental patch from Magnus Damm. Signed-off-by:
-
Jacopo Mondi authored
Add compatible string for R-Car E3 R8A77990 to the list of SoCs supported by rcar-vin driver. Signed-off-by:
-
Fabio Estevam authored
Improve the pxp_soft_reset() error message by moving it to the caller function, associating it with a proper device and also by displaying the error code. Signed-off-by:
Fabio Estevam <festevam@gmail.com> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Fabio Estevam authored
pxp_soft_reset() may fail with a timeout, so it is better to propagate the error in this case. Signed-off-by:
-
Fabio Estevam authored
clk_prepare_enable() may fail, so we should better check its return value and propagate it in the case of error. Signed-off-by:
-
Philipp Zabel authored
In addition to the S_FMT debug output, S_SELECTION (SEL_TGT_CROP) is relevant to determine encoded size. Add debug output for it. Signed-off-by:
-
Philipp Zabel authored
Consistently add the context index to debug output, which otherwise is impossible to make sense of when two contexts are running concurrently. For this purpose, add a convenience macro coda_dbg(). Use the function name with the coda_ prefix stripped as keyword where applicable, and consistently use vid-out and vid-cap names for the queues. Add sequence counters to the decoder job finished message and correctly indicate B frames. Add a start streaming message to complement the stop streaming message and a start encoding message to complement the existing start decoding message. Signed-off-by:
-
Philipp Zabel authored
Use v4l2_type_names to indicate which of the two queues is busy. Signed-off-by:
-
Michael Tretter authored
The error code looks much more like a bit field than an error value. Print it as hex rather than decimal. Signed-off-by:
Michael Tretter <m.tretter@pengutronix.de> Signed-off-by:
-
Philipp Zabel authored
v4l2-compliance complains if S_SELECTION returns 0 for read-only targets. Signed-off-by:
-
Philipp Zabel authored
v4l2-compliance complains if G_PARM returns 0 in the denominator. Signed-off-by:
-
Philipp Zabel authored
v4l2-compliance complains about S_PARM being supported, but not ENUM_FRAMEINTERVALS. Report a continuous frame interval even though the hardware only supports 16-bit numerator and denominator, with min/max values that can be programmed into the mailbox registers. Signed-off-by:
-
Philipp Zabel authored
The flag is already set in coda_g_parm, but v4l2-compliance complains about it not being set during S_PARM. Signed-off-by:
-
Lucas Stach authored
The CODA driver uses threaded IRQs only, so there is nothing happening in hardirq context that could interfere with the buffer meta handling. Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Signed-off-by:
-
Philipp Zabel authored
The per-device instance list is unused, remove it. Signed-off-by:
-
Philipp Zabel authored
Three macroblocks seem to be the minimum resolution that can be encoded and decoded by the CODA960 h.264 codec. Picture run commands fail for smaller resolutions. Signed-off-by:
-
Lucas Stach authored
The ringbuffer used to hold the bitstream is very conservatively sized, as keyframes can get very large and still need to fit into this buffer. This means that the buffer is way oversized for the average stream to the extend that it will hold a few hundred frames when the video data is compressing well. The current strategy of queueing as much bitstream data as possible leads to large delays when draining the decoder. In order to keep the drain latency to a reasonable bound, try to only queue a full reorder window of buffers. We can't always hit this low target for very well compressible video data, as we might end up with less than the minimum amount of data that needs to be available to the bitstream prefetcher, so we must take this into account and allow more buffers to be queued in this case. Signed-off-by:
-
Philipp Zabel authored
The bitstream prefetch unit reads data in 256 byte blocks with some kind of queueing. For the decoder to see data up to a desired position in the next run, the bitstream has to be filled for 2 256 byte blocks past that position aligned up to the next 256 byte boundary. This should make sure we never run into a buffer underrun condition if userspace does not supply new input buffers fast enough. Signed-off-by:
-
Philipp Zabel authored
Storing the unmasked kfifo->in position as meta->start and ->end allows to more easily compare a point past meta->end with the current kfifo->in. Signed-off-by:
-
Philipp Zabel authored
The ffz() return value is undefined if the instance mask does not contain any zeros. If it returned 32, the following set_bit would corrupt the debugfs_root pointer. Switch to IDA for context index allocation. This also removes the artificial 32 instance limit for all except CodaDx6. Signed-off-by:
-
Rui Miguel Silva authored
Swapping the order between v4l2 subdevice registration and checking chip id in b7a41762 ("media: ov2680: don't register the v4l2 subdevice before checking chip ID") makes the mode restore to use the sensor controls before they are set, so move the mode restore call to s_power after the handler setup for controls is done. This remove also the need for the error code path in power on function. Fixes: b7a41762 ("media: ov2680: don't register the v4l2 subdevice before checking chip ID") Signed-off-by:
Rui Miguel Silva <rui.silva@linaro.org> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Sakari Ailus authored
Document that changing the frame interval has no effect on frame size. While this was the assumption in the API, it was not documented as such. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Maxime Ripard authored
The first device that used that IP was the A31. Add it to our list of compatibles. Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
-
Maxime Ripard authored
The H3 has a slightly different CSI controller (no BT656, no CCI) which looks a lot like the original A31 controller. Add a compatible for the A31, and more specific compatible the for the H3 to be used in combination for the A31. Reviewed-by:
-
Mauro Carvalho Chehab authored
There are a few other coding style issues reported by checkpatch while in --strict mode. Fix the ones that make sense. Signed-off-by: -
Mauro Carvalho Chehab authored
Make checkpatch.pl happier by running it on strict mode and using the --fix-inline to solve some issues. Signed-off-by: -
Yong Deng authored
Allwinner V3s SoC features a CSI module with parallel interface. This patch implement a v4l2 framework driver for it. Reviewed-by:
Yong Deng <yong.deng@magewell.com> Signed-off-by:
-
Yong Deng authored
Add binding documentation for Allwinner V3s CSI. Acked-by:
-
Akinobu Mita authored
This adds log_status ioctl and event interface for ov772x's v4l2 controls. Cc: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
-
Akinobu Mita authored
This adds log_status ioctl and event interface for ov7670's v4l2 controls. Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by:
-
Akinobu Mita authored
This adds log_status ioctl and event interface for ov5640's v4l2 controls. Cc: Steve Longerbeam <slongerbeam@gmail.com> Signed-off-by:
-
Akinobu Mita authored
This adds log_status ioctl and event interface for ov2640's v4l2 controls. Signed-off-by:
-
Akinobu Mita authored
The ov2640 has the test pattern generator features. This makes use of it through V4L2_CID_TEST_PATTERN control. [Sakari Ailus: Use "Eight Vertical Colour Bars" as the second manu entry] Signed-off-by:
-
Akinobu Mita authored
The mt9m111 has special camera effects feature. This makes use of it through V4L2_CID_COLORFX control. Signed-off-by:
-
