Basic MFD framework for the MSP430 microcontroller firmware used
on the dm355evm board:

 - Provides an interface for other drivers: register read/write
   utilities, and register declarations.

 - Directly exports:
     * Many signals through the GPIO framework
         + LEDs
         + SW6 through gpio sysfs
	 + NTSC/nPAL jumper through gpio sysfs
	 + ... more could be added later, e.g. MMC signals
     * Child devices:
	+ LEDs, via leds-gpio child (and default triggers)
	+ RTC, via rtc-dm355evm child device
	+ Buttons and IR control, via dm355evm_keys

 - Supports power-off system call.  Use the reset button to power
   the board back up; the power supply LED will be on, but the
   MSP430 waits to re-activate the regulators.

 - On probe() this:
     * Announces firmware revision
     * Turns off the banked LEDs
     * Exports the resources noted above
     * Hooks the power-off support
     * Muxes tvp5146 -or- imager for video input

Unless the new tvp514x driver (tracked for mainline) is configured,
this assumes that some custom imager driver handles video-in.

This completely ignores the registers reporting the output voltages
on the various power supplies.  Someone could add a hwmon interface
if that seems useful.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

The WM8351 is a WM8350 variant. As well as register default changes the
WM8351 has fewer voltage and current regulators than the WM8350.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Some WM8350 variants have fewer DCDCs and ISINKs. Identify these at
probe and refuse to use the absent DCDCs when running on these chips.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

The WM8352 is a variant of the WM8350. Aside from the register defaults
there are no software visible differences to the WM8350.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

The global irq_desc array is soon going to be accessible only with
!CONFIG_SPARSE_IRQ. We should start using the generic irq_to_desc()
routines instead.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Driver for battery charger integrated into Dialog Semiconductor DA9030 PMIC
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

This patch amends DA903x MFD driver with definitions and methods
needed for battery charger driver.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Register a child device for the codec in the WM8400.

Also switch the unregistration of the MFD devices to use the MFD core
since the current code is hand rolling the same thing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

The MFD cell structure provides a driver_data field but doesn't pass it
on to the child devices when instantiating them - do that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

This is a fix for:

twl4030-core.c:(.text+0x16a797): undefined reference to `clk_get_rate'
twl4030-core.c:(.text+0x16a797): undefined reference to `clk_put'

on x86 and x86_64, as the clock API is not defined on those platforms.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

This contains two bugfixes to the initial twl4030 regulator
support patch related to USB:

 (a) always overwrite the old list of consumers ... else
     the regulator handles all use the same "usb1v5" name;
 (b) don't set up the "usbcp" regulator, which turns out
     to be managed through separate controls, usually ULPI
     directly from the OTG controller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Initial code to create twl4030 voltage regulator devices, using
the new regulator framework.  Note that this now starts to care
what name is used to declare the TWL chip:

 - TWL4030 is the "old" chip; newer ones have a bigger variety
   of VAUX2 voltages.

 - TWL5030 is the core "new" chip; TPS65950 is its catalog version.

 - The TPS65930 and TPS65920 are cost-reduced catalog versions of
   TWL5030 parts ... fewer regulators, no battery charger, etc.

Board-specific regulator configuration should be provided, listing
which regulators are used and their constraints (e.g. 1.8V only).

Code that could ("should"?) leverage the regulator stuff includes
TWL4030 USB transceiver support and MMC glue, LCD support for the
3430SDP and Labrador boards, and S-Video output.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Finish removing dependency of TWL driver stack on platform-specific
IRQ definitions ... and remove the build dependency on OMAP.

This lets the TWL4030 code be included in test builds for most
platforms, and will make it easier for non-OMAP folk to update
most of this code for new APIs etc.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Minor cleanup to twl4030-core: define a helper function to populate
a single child node, and use it to replace six inconsistent versions
of the same logic.  Both object and source code shrink.

As part of this, some devices now have more IRQ resources:  battery
charger, keypad, ADC, and USB transceiver.  That helps to remove some
irq #defines that block the children's drivers code from compiling on
non-OMAP platforms.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Implement support for reporting battery health in the WM8350 battery
interface. Since we are now able to report this via the classs remove
the diagnostics from the interrupt handler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Some systems are able to report problems with batteries being under
temperature.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Since the WM8350 driver was originally written the semantics for the
identification registers of the chip have been clarified, allowing
us to do an exact match on all the fields. This avoids mistakenly
running on unsupported hardware.

Also change to using the datasheet names more consistently for
legibility and fix a printk() that should be dev_err().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Rather than check for chip revisions in the WM8350 drivers have the core
code set flags for relevant differences.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

This patch adds support for the PMU provided by the WM8350 which
implements battery, line and USB supplies including a battery charger.
The hardware functions largely autonomously, with minimal software
control required to initiate fast charging.

Support for configuration of the USB supply is not yet implemented.
This means that the hardware will remain in the mode configured at
startup, by default limiting the current drawn from USB to 100mA.

This driver was originally written by Liam Girdwood with subsequent
updates for submission by Mark Brown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Minor change to the TWL4030 utility interface:  support reads
of all 256 bytes in each register bank (vs just 255).  This
can help when debugging, but is otherwise a NOP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

The auxiliary ADC in the WM8350 is shared between several subdevices
so access to it needs to be arbitrated by the core driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

No other software changes are required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Hopefully this will make the purpose of these functions a bit clearer,
it's not immediately obvious that the lock is a hardware feature.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

There's no need to read this back from the chip each time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Merge branch 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (77 commits)
  x86: setup_per_cpu_areas() cleanup
  cpumask: fix compile error when CONFIG_NR_CPUS is not defined
  cpumask: use alloc_cpumask_var_node where appropriate
  cpumask: convert shared_cpu_map in acpi_processor* structs to cpumask_var_t
  x86: use cpumask_var_t in acpi/boot.c
  x86: cleanup some remaining usages of NR_CPUS where s/b nr_cpu_ids
  sched: put back some stack hog changes that were undone in kernel/sched.c
  x86: enable cpus display of kernel_max and offlined cpus
  ia64: cpumask fix for is_affinity_mask_valid()
  cpumask: convert RCU implementations, fix
  xtensa: define __fls
  mn10300: define __fls
  m32r: define __fls
  h8300: define __fls
  frv: define __fls
  cris: define __fls
  cpumask: CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS
  cpumask: zero extra bits in alloc_cpumask_var_node
  cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
  cpumask: convert mm/
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/linux-2.6-iommu: (89 commits)
  AMD IOMMU: remove now unnecessary #ifdefs
  AMD IOMMU: prealloc_protection_domains should be static
  kvm/iommu: fix compile warning
  AMD IOMMU: add statistics about total number of map requests
  AMD IOMMU: add statistics about allocated io memory
  AMD IOMMU: add stats counter for domain tlb flushes
  AMD IOMMU: add stats counter for single iommu domain tlb flushes
  AMD IOMMU: add stats counter for cross-page request
  AMD IOMMU: add stats counter for free_coherent requests
  AMD IOMMU: add stats counter for alloc_coherent requests
  AMD IOMMU: add stats counter for unmap_sg requests
  AMD IOMMU: add stats counter for map_sg requests
  AMD IOMMU: add stats counter for unmap_single requests
  AMD IOMMU: add stats counter for map_single requests
  AMD IOMMU: add stats counter for completion wait events
  AMD IOMMU: add init code for statistic collection
  AMD IOMMU: add necessary header defines for stats counting
  AMD IOMMU: add Kconfig entry for statistic collection code
  AMD IOMMU: use dev_name in iommu_enable function
  AMD IOMMU: use calc_devid in prealloc_protection_domains
  ...

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (34 commits)
  V4L/DVB (10173): Missing v4l2_prio_close in radio_release
  V4L/DVB (10172): add DVB_DEVICE_TYPE= to uevent
  V4L/DVB (10171): Use usb_set_intfdata
  V4L/DVB (10170): tuner-simple: prevent possible OOPS caused by divide by zero error
  V4L/DVB (10168): sms1xxx: fix inverted gpio for lna control on tiger r2
  V4L/DVB (10167): sms1xxx: add support for inverted gpio
  V4L/DVB (10166): dvb frontend: stop using non-C99 compliant comments
  V4L/DVB (10165): Add FE_CAN_2G_MODULATION flag to frontends that support DVB-S2
  V4L/DVB (10164): Add missing S2 caps flag to S2API
  V4L/DVB (10163): em28xx: allocate adev together with struct em28xx dev
  V4L/DVB (10162): tuner-simple: Fix tuner type set message
  V4L/DVB (10161): saa7134: fix autodetection for AVer TV GO 007 FM Plus
  V4L/DVB (10160): em28xx: update chip id for em2710
  V4L/DVB (10157): Add USB ID for the Sil4701 radio from DealExtreme
  V4L/DVB (10156): saa7134: Add support for Avermedia AVer TV GO 007 FM Plus
  V4L/DVB (10155): Add TEA5764 radio driver
  V4L/DVB (10154): saa7134: fix a merge conflict on Behold H6 board
  V4L/DVB (10153): Add the Beholder H6 card to DVB-T part of sources.
  V4L/DVB (10152): Change configuration of the Beholder H6 card
  V4L/DVB (10151): Fix I2C bridge error in zl10353
  ...

those two functions only used in that C file
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  mmc: warn about voltage mismatches
  mmc_spi: Add support for OpenFirmware bindings
  pxamci: fix dma_unmap_sg length
  mmc_block: ensure all sectors that do not have errors are read
  drivers/mmc: Move a dereference below a NULL test
  sdhci: handle built-in sdhci with modular leds class
  mmc: balanc pci_iomap with pci_iounmap
  mmc_block: print better error messages
  mmc: Add mmc_vddrange_to_ocrmask() helper function
  ricoh_mmc: Handle newer models of Ricoh controllers
  mmc: Add 8-bit bus width support
  sdhci: activate led support also when module
  mmc: trivial annotation of 'blocks'
  pci: use pci_ioremap_bar() in drivers/mmc
  sdricoh_cs: Add support for Bay Controller devices
  mmc: at91_mci: reorder timer setup and mmc_add_host() call

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] Add support for the WM8350 watchdog
  [WATCHDOG] Add SMSC SCH311x Watchdog Timer.
  [WATCHDOG] ib700wdt - add timeout parameter

* 'cputime' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [PATCH] fast vdso implementation for CLOCK_THREAD_CPUTIME_ID
  [PATCH] improve idle cputime accounting
  [PATCH] improve precision of idle time detection.
  [PATCH] improve precision of process accounting.
  [PATCH] idle cputime accounting
  [PATCH] fix scaled & unscaled cputime accounting

Before, when we only ever printed out the pointer value itself, a NULL
pointer would never cause issues and might as well be printed out as
just its numeric value.

However, with the extended %p formats, especially %pR, we might validly
want to print out resources for debugging.  And sometimes they don't
even exist, and the resource pointer is just NULL.  Print it out as
such, rather than oopsing.

This is a more generic version of a patch done by Trent Piepho (catching
all %p cases rather than just %pR, and using "(null)" instead of
"[NULL]" to match glibc).
Requested-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

... just make it a binfmt handler like #! one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

They are actually alpha vs.  i386/arm/m68k i.e. ecoff vs. aout.

In the only place where we actually tried to handle arm and i386/m68k in
different ways (START_DATA() in coredump handling), the arm variant
works for all of them (i386 and m68k have u.start_code set to 0).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

it's been used only in sunos compat
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This updates some personal info in the CREDITS file.

I'm no longer actively involved in Keyspan driver work so shouldn't
really be listed as a Maintainer here.

I do however field the occasional question on them and as I'm dropping
the misc.nu domain, want to ensure people can find me should they need
to.
Signed-off-by: Hugh Blemings <hugh@blemings.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Impact: cleanup

__alloc_bootmem and __alloc_bootmem_node do panic
for us in case of fail so no need for additional
checks here.

Also lets use pr_*() macros for printing.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>