- 31 Jul, 2018 5 commits
-
-
Boris Brezillon authored
Commit 260e89a6 ("mtd: core: tone down suggestion that dev.parent should be set") removed the only user of caller_is_module() but forgot to remove the definition itself. Let's remove it now. Signed-off-by:
Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by:
Miquel Raynal <miquel.raynal@bootlin.com>
-
Boris Brezillon authored
All of the code in the probe path assumes ->sets != NULL and ->nrsets > 0. Error out if that's not the case to avoid dereferencing a NULL pointer. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Miquel Raynal authored
A report from Colin Ian King pointed a CoverityScan issue where error values on these helpers where not checked in the drivers. These helpers can error out only in case of a software bug in driver code, not because of a runtime/hardware error. Hence, let's WARN_ON() in this case and return 0 which is harmless anyway. Fixes: 8878b126 ("mtd: nand: add ->exec_op() implementation") Signed-off-by:
-
Boris Brezillon authored
Make sure __LINUX_ARM_ARCH__ is defined before testing its value. This is needed if we want to allow selection of this driver when COMPILE_TEST=y. Signed-off-by:
-
Boris Brezillon authored
Include linux/sizes.h instead of asm/sizes.h to make code completely arch independent. Signed-off-by:
-
- 19 Jul, 2018 16 commits
-
-
Boris Brezillon authored
We currently don't store the on-die ECC state (enabled/disabled) which might force us to re-disable the engine even if it's already been disabled after we've read the page in raw mode to count the actual number of bitflips. Add an "enabled" field to struct micron_on_die_ecc to keep track of the ECC state. Signed-off-by:
Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by:
-
Boris Brezillon authored
Some chips have their on-die ECC forcibly enabled, there's no point in trying to enable/disable the ECC engine in that case. Signed-off-by:
-
Boris Brezillon authored
The MT29F2Gxxx chips with 4bits/512byte on-die ECC let us know when some bitflips were corrected by the on-die ECC, but they do not report the actual number of bitflips that were present in the data+ECC chunk. We initially decided to always return ecc->strength to avoid re-reading the page in raw mode + comparing it to the corrected buffer to extract the real number of bitflips, but this forces UBI to move data around as soon as one bitflip is present in a page. This not only wears the NAND out faster, but also degrades performances, since reading a full PEB + writing it back to a different PEB + erasing the old one is much more expensive than re-reading the faulty page in raw mode and comparing it to the corrected buffer. In most cases, the actual number of bitflips does not exceed the bitflips threshold, and UBI won't have to move data around. Otherwise, we can assume the time spent re-reading the page and doing the comparison is negligible compared to the time UBI spends moving a full PEB to another PEB. Note that this logic is not applied to chips with 8bits/512byte on-die ECC, because those chips provide fine-grained information (the maximum error is 1 bit, and it will not force UBI to move blocks around at the first bitflip). Suggested-by:
Bean Huo <beanhuo@micron.com> Signed-off-by:
-
Chris Packham authored
Some Micron NAND chips have on-die ECC forceably enabled. Allow such chips to be used as long as the controller has set chip->ecc.mode to NAND_ECC_ON_DIE. Signed-off-by:
-
Boris Brezillon authored
Some implementations simply can't disable their ECC engine. Expose helpers returning -ENOTSUPP so that the caller knows that raw accesses are not supported instead of silently falling back to non-raw accessors. Signed-off-by:
-
Chris Packham authored
Micron MT29F1G08ABAFAWP-ITE:F supports an on-die ECC with 8 bits per 512 bytes. Add support for this combination. Signed-off-by:
-
Boris Brezillon authored
Basing the "mandatory on-die" detection on ID byte 2 does not work, because Micron has plenty of NANDs using the same device ID code, and not all of them have forcibly enabled on-die ECC. Since the "Array Operation" feature does not provide the "ECC enabled/disabled" bit when the ECC can't be disabled, let's try to use the "ECC enabled/disabled" bit in the READ_ID bytes. It seems that this bit is dynamically updated on NANDs where on-die ECC can freely be enabled/disabled, so let's hope it stays at one when we have a NAND with on-die ECC forcibly enabled. Fixes: 51f3b3970a8c ("mtd: rawnand: micron: detect forced on-die ECC") Signed-off-by: -
Boris Brezillon authored
chip->read_buf is left unassigned since commit 4da712e7 ("mtd: nand: fsmc: use ->exec_op()"), leading to a NULL pointer dereference when it's called from fsmc_read_page_hwecc(). Fix that by using the appropriate helper to read data out of the NAND. Fixes: 4da712e7 ("mtd: nand: fsmc: use ->exec_op()") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Arnd Bergmann authored
Compile-testing this driver on x86 caused a link error: ERROR: "__phys_to_dma" [drivers/mtd/nand/raw/qcom_nandc.ko] undefined! The problem here is that the driver attempts to convert the physical address into the DMA controller as a dma_addr_t and calls phys_to_dma() to do the conversion. The correct way to do the conversion is using the dma mapping interfaces. Fixes: c76b78d8 ("mtd: nand: Qualcomm NAND controller driver") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Reviewed-by:
-
Stefan Agner authored
The Tegra driver currently only support a single chip select, hence check boundaries accordingly. This fixes a off by one issue catched with Smatch: drivers/mtd/nand/raw/tegra_nand.c:476 tegra_nand_select_chip() warn: array off by one? 'nand->cs[die_nr]' Also warn in case the stack asks for a chip select we currently do not support. Reported-by:Stefan Agner <stefan@agner.ch> Signed-off-by:
Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by:
-
Miquel Raynal authored
Some timings like tBERS (block erase time), tCCs (change column setup time), tPROG (page program time) and tR (page read time) are derived from the ONFI parameter page. They are set in the SDR interface only if the chip is ONFI compliant. It makes these timings unreliable and prevent the driver to use one of these four values with a non-ONFI chip. Fix this situation by taking the highest possible value (or a default one) value for each missing timing (stored as unsigned 16-bit entries in the parameter page). This makes tBERS and tPROG being ~65ms while typical values are at most a few milliseconds. As these are timeouts, it is not impacting at all the performances in nominal use. tR maximum time and tCCS minimum time (delay to wait after a change column) are set, according to the ONFI specification, to default 'slow' values; respectively 200us and 500ns. Signed-off-by:
-
Rafał Miłecki authored
If driver doesn't specify parsers it can use that little helper. Signed-off-by:
Rafał Miłecki <rafal@milecki.pl> Signed-off-by:
-
Rafał Miłecki authored
If driver doesn't specify parsers it can use that little helper. Signed-off-by:
Xiaolei Li <xiaolei.li@mediatek.com> Signed-off-by:
-
Arnd Bergmann authored
We already have a dependency on BCMA_NFLASH, which in turn depends on BCMA, but since BCMA is a tristate option and BCMA_NFLASH is bool, we can run into an invalid configuration with MTD_NAND_BCM47XXNFLASH=y and BCMA=m: drivers/mtd/nand/raw/bcm47xxnflash/ops_bcm4706.o: In function `bcm47xxnflash_ops_bcm4706_init': ops_bcm4706.c:(.text+0x790): undefined reference to `bcma_chipco_pll_read' Adding the dependency here forces MTD_NAND_BCM47XXNFLASH to only be configured =m here so it can link against the BCMA driver. Signed-off-by:
-
Boris Brezillon authored
It just makes maintainers' life easier by allowing them to compile-test this driver without having MACH_JZ4780 enabled. We also need to add a dependency on HAS_IOMEM to make sure the driver compiles correctly. Signed-off-by:
Paul Burton <paul.burton@mips.com> Signed-off-by:
-
Boris Brezillon authored
In jz_nand_detect_bank(), chipnr is a size_t argument. Use %zu instead of %i when printing it. Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
- 18 Jul, 2018 19 commits
-
-
Boris Brezillon authored
This MACH_JZ4780 dependency is taken care of by JZ4780_NEMC, no need to repeat it here. Signed-off-by:
-
Boris Brezillon authored
It just makes NAND maintainers' life easier by allowing them to compile-test this driver without having MACH_JZ4740 enabled. We also need to add a dependency on HAS_IOMEM to make sure the driver compiles correctly. Signed-off-by:
-
Boris Brezillon authored
This way we will be able to compile the jz4740_nand driver when COMPILE_TEST=y. Signed-off-by:
-
Boris Brezillon authored
It just makes NAND maintainers' life easier by allowing them to compile-test this driver without having SOC_TX4938 or SOC_TX4939 enabled. We also need to add a dependency on HAS_IOMEM to make sure the driver compiles correctly. Signed-off-by:
-
Boris Brezillon authored
This way we will be able to compile the ndfmc driver when COMPILE_TEST=y. Signed-off-by:
-
Boris Brezillon authored
It just makes maintainers' life easier by allowing them to compile-test this driver without having FSL_SOC, ARCH_LAYERSCAPE or SOC_LS1021A enabled. We also need to add a dependency on HAS_IOMEM to make sure the driver compiles correctly. Signed-off-by:
-
Boris Brezillon authored
The local eccstat_regs variable in fsl_ifc_run_command() is missing an __iomem specifier, and sparce complains about that. Signed-off-by:
-
Boris Brezillon authored
It just makes maintainers' life easier by allowing them to compile-test this driver without having FSL_SOC, ARCH_LAYERSCAPE or SOC_LS1021A enabled. We also need to add a dependency on HAS_IOMEM to make sure the driver compiles correctly. Signed-off-by:
-
Boris Brezillon authored
It just makes NAND maintainers' life easier by allowing them to compile-test this driver without having PLAT_SPEAR, ARCH_NOMADIK, ARCH_U8500 or MACH_U300 enabled. We also need to add a dependency on HAS_IOMEM to make sure the driver compiles correctly. Signed-off-by:
-
Boris Brezillon authored
uintptr_t should be used when casting a pointer to an unsigned int so that the code compiles without warnings even on 64-bit architectures. This is needed if we want to allow selection of this driver when COMPILE_TEST=y. Signed-off-by:
-
Boris Brezillon authored
We want to allow this driver to be selected when COMPILE_TEST=y, this means the driver can be compiled for any arch, including MIPS. When compiling this driver for MIPS, we end up with a collision on the 'PC' macro definition (also defined in arch/mips/include/asm/ptrace.h). Prefix the fsmc one with FSMC_ to avoid this problem. Signed-off-by:
-
Boris Brezillon authored
It just makes NAND maintainers' life easier by allowing them to compile-test this driver without having ARCH_SUNXI enabled. We also need to add a dependency on HAS_IOMEM to make sure the driver compiles correctly. Signed-off-by:
-
Boris Brezillon authored
Fixes the following smatch warning: drivers/mtd/nand/raw/sunxi_nand.c:551 sunxi_nfc_read_byte() error: uninitialized symbol 'ret'. Signed-off-by:
-
Boris Brezillon authored
Fixes the "warning: large integer implicitly truncated to unsigned type [-Woverflow]" warning when compiled for x86. This is needed in order to allow compiling this driver when COMPILE_TEST=y. Reported-by:
-
Boris Brezillon authored
It just makes NAND maintainers' life easier by allowing them to compile-test this driver without having ARCH_DAVINCI or ARCH_KEYSTONE enabled. We also need to add a dependency on HAS_IOMEM to make sure the driver compiles correctly. Signed-off-by:
-
Miquel Raynal authored
Rules about Kconfig are simple but in the raw NAND directory indentation is somehow archaic. Fix the indentation in the whole file. Signed-off-by: -
Boris Brezillon authored
uintptr_t should be used when casting a pointer to an unsigned int so that the code compiles without warnings even on 64-bit architectures. This is needed if we want to allow selection of this driver when COMPILE_TEST=y. Reported-by:
-
Boris Brezillon authored
There is no point in doing this sort of conversion since we can replace |= by += operations which are perfectly valid on pointers. This is done in preparation of COMPILE_TEST addition to the NAND_DAVINCI Kconfig entry, since building for x86 generates several warnings because of inappropriate u32 <-> void * conversions (pointers are 64-bit large on x86_64). Reported-by:
-
Boris Brezillon authored
It just makes NAND maintainers' life easier by allowing them to compile-test this driver without having ARCH_AT91 enabled. We also need to add a dependency on HAS_IOMEM to make sure the driver compiles correctly. Signed-off-by:
-
