- 15 May, 2018 5 commits
-
-
Fabio Estevam authored
Adopt the SPDX license identifier headers to ease license compliance management. Signed-off-by:
Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by:
Shawn Guo <shawnguo@kernel.org>
-
Hernán Gonzalez authored
Replace magic number with the proper IRQ_TYPE specifier to improve DT readability. Signed-off-by:
Hernán Gonzalez <hernan@vanguardiasur.com.ar> Signed-off-by:
-
Hernán Gonzalez authored
Replace magic number with the proper IRQ_TYPE specifier to improve DT readability. Signed-off-by:
-
Hernán Gonzalez authored
Replace magic number with the proper IRQ_TYPE specifier to improve DT readability. Signed-off-by:
-
Hernán Gonzalez authored
GPIO_ACTIVE_LOW was being used to specify an interrupt, use IRQ_TYPE_EDGE_RISING instead. This improves DT readability. Signed-off-by:
-
- 14 May, 2018 35 commits
-
-
Fabio Estevam authored
Instead of hardcoding the input codes we can use the symbol name for better readability. Signed-off-by:
-
Fabio Estevam authored
Instead of hardcoding the input codes we can use the symbol name for better readability. Signed-off-by:
-
Fabio Estevam authored
Instead of hardcoding the input codes we can use the symbol name for better readability. Signed-off-by:
-
Rob Herring authored
OF graph endpoint connections must be bidirectional and dtc will now warn if they are not. i.MX7 based DTs have an error and generate warnings: Warning (graph_endpoint): /replicator/ports/port@0/endpoint: graph connection to node '/soc/tpiu@30087000/port/endpoint' is not bidirectional Warning (graph_endpoint): /soc/tpiu@30087000/port/endpoint: graph connection to node '/replicator/ports/port@1/endpoint' is not bidirectional This appears to be a copy-n-paste error and the TPIU input should be connected to replicator port 0 instead of port 1. Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Rob Herring authored
Single child nodes in OF graph don't need an address and now dtc will warn about this: Warning (graph_child_address): /soc/aips@50000000/ldb@53fa8008/lvds-channel@0: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary Since the LDB should always have an output port, fix the warning by adding the output port, 2, to the DT. Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Rob Herring authored
OF graph endpoint nodes are supposed to be named 'endpoint' with an address if there is more than one. The i.MX IPU binding graph has used unique endpoint names instead which now generate dtc warnings: Warning (graph_endpoint): /soc/ipu@2400000/port@2/disp0-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2400000/port@2/hdmi-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2400000/port@2/mipi-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2400000/port@2/lvds0-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2400000/port@2/lvds1-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2400000/port@3/disp1-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2400000/port@3/hdmi-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2400000/port@3/mipi-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2400000/port@3/lvds0-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2400000/port@3/lvds1-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2800000/port@2/disp0-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2800000/port@2/hdmi-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2800000/port@2/mipi-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2800000/port@2/lvds0-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2800000/port@2/lvds1-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2800000/port@3/hdmi-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2800000/port@3/mipi-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2800000/port@3/lvds0-endpoint: graph endpont node name should be 'endpoint' Warning (graph_endpoint): /soc/ipu@2800000/port@3/lvds1-endpoint: graph endpont node name should be 'endpoint' Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by:
-
Fabio Estevam authored
Adopt the SPDX license identifier headers to ease license compliance management. Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warnings: arch/arm/boot/dts/imx28-duckbill-2-enocean.dtb: Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" propert Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warnings: arch/arm/boot/dts/imx28-cfa10049.dtb: Warning (avoid_unnecessary_addr_size): /gpio_keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
-
Ken Lin authored
Add the 4th partiton named "mfg" with a block size 64K to store manufacturing data. Signed-off-by:
Ken Lin <ken.lin@advantech.com.tw> Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by:
-
Fabio Estevam authored
Adopt the SPDX license identifier headers to ease license compliance management. Signed-off-by:
-
Fabio Estevam authored
Adopt the SPDX license identifier headers to ease license compliance management. Signed-off-by:
-
Shawn Guo authored
It replaces underscore with hyphen in aliases name to fix DTC alias_paths warning below, which is seen with various i.MX board dts files when W=1 switch is on. Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-' Signed-off-by:
Lothar Waßmann <LW@KARO-electronics.de> Reviewed-by:
Gary Bisson <gary.bisson@boundarydevices.com>
-
Shawn Guo authored
For soc level of clocks which are input to Clock Control Module, clock driver expects them to be under 'clocks' container node. But for board level clocks, this container is not really necessary. Let's drop it and use an unique name for fixed rate clock, so that 'reg' property can be saved as well. Signed-off-by:
-
Shawn Guo authored
Instead of copying the whole node hierarchy, let's define a label for clock osc26m in soc dtsi and use it for overriding clock-frequency. Signed-off-by: -
Shawn Guo authored
The clk32 clock is an input clock to CCM module, and should be defined in soc dtsi rather than a board level dts. Let's move it into imx1.dtsi. While at it, let's drop unnecessary #address-cells/#size-cells from 'clocks' node to DTC warning avoid_unnecessary_addr_size seen with W=1 switch. Signed-off-by: -
Shawn Guo authored
It drops unnecessary #address-cells/#size-cells from <soc>.dtsi 'clocks' node to fix DTC warning avoid_unnecessary_addr_size seen with W=1 switch. Signed-off-by: -
Anson Huang authored
Add egalax touch screen support on i2c2 bus. Signed-off-by:
Anson Huang <Anson.Huang@nxp.com> Reviewed-by:
-
Anson Huang authored
There is a debug LED(D11) connected to GPIO1_IO24, add support for it. Signed-off-by:
-
Anson Huang authored
i.MX6SX Sabre Auto board has GPIO1_IO13 pin can be MUXed as WDOG output to reset PMIC, add this function support. Signed-off-by:
-
Anson Huang authored
Add FEC support on i.MX6SX Sabre Auto board. Signed-off-by:
-
Anson Huang authored
i.MX6SX Sabre Auto board has two max7310 IO expander on I2C3 bus, add support for them. Signed-off-by:
-
Anson Huang authored
Add MAX7322 IO expander support. Signed-off-by:
-
Anson Huang authored
Add pfuze100 support on i.MX6SX Sabre Auto board. Signed-off-by:
-
Shawn Guo authored
The board specific pinctrl function container node 'imx6x-sabreauto' is not really necessary, since commit 5fcdf6a7 ("pinctrl: imx: Allow parsing DT without function nodes"). Let's drop it to save one level of indentation. Signed-off-by:
-
Shawn Guo authored
Let's drop the 'regulators' container node by giving VCC_SD3 an unique name and removing 'reg' property, so that the fixed regulator can be under root node directly. Signed-off-by: -
Fabio Estevam authored
The 'fsl,uart-has-rtscts' property is deprecated and it is recommended to use the generic 'uart-has-rtscts' property instead. Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warning: arch/arm/boot/dts/imx6q-var-dt6customboard.dtb: Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warning: arch/arm/boot/dts/imx6q-utilite-pro.dtb: Warning (avoid_unnecessary_addr_size): /encoder: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warnings: arch/arm/boot/dts/imx6q-b850v3.dtb: Warning (avoid_unnecessary_addr_size): /soc/aips-bus@2100000/i2c@21a4000/mux@70/i2c@1/stdp2690@72: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/boot/dts/imx6q-b850v3.dtb: Warning (avoid_unnecessary_addr_size): /soc/aips-bus@2100000/i2c@21a4000/mux@70/i2c@1/stdp4028@73: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warning: arch/arm/boot/dts/imx6dl-aristainetos2_4.dtb: Warning (avoid_unnecessary_addr_size): /soc/aips-bus@2000000/spba-bus@2000000/ecspi@2008000/display@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warnings: arch/arm/boot/dts/imx53-ppd.dtb: Warning (avoid_unnecessary_addr_size): /power-gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/boot/dts/imx53-ppd.dtb: Warning (avoid_unnecessary_addr_size): /touch-lock-key: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warnings: arch/arm/boot/dts/imx6q-novena.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@2400000/port@2: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/boot/dts/imx6q-novena.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@2400000/port@3: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/boot/dts/imx6q-novena.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@2800000/port@2: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/boot/dts/imx6q-novena.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@2800000/port@3: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warnings: arch/arm/boot/dts/imx6q-novena.dtb: Warning (avoid_unnecessary_addr_size): /soc/aips-bus@2100000/i2c@21a0000/stmpe811@44: unnecessary #address-cells/#size-cells without "ranges" or child "reg" Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells from the switch nodes to fix the following DTC warnings: arch/arm/boot/dts/imx6q-b450v3.dtb: Warning (avoid_unnecessary_addr_size): /mdio-gpio/switch@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
-
