- 14 May, 2018 18 commits
-
-
Anson Huang authored
Add egalax touch screen support on i2c2 bus. Signed-off-by:
Anson Huang <Anson.Huang@nxp.com> Reviewed-by:
Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by:
Shawn Guo <shawnguo@kernel.org>
-
Anson Huang authored
There is a debug LED(D11) connected to GPIO1_IO24, add support for it. Signed-off-by:
-
Anson Huang authored
i.MX6SX Sabre Auto board has GPIO1_IO13 pin can be MUXed as WDOG output to reset PMIC, add this function support. Signed-off-by:
-
Anson Huang authored
Add FEC support on i.MX6SX Sabre Auto board. Signed-off-by:
-
Anson Huang authored
i.MX6SX Sabre Auto board has two max7310 IO expander on I2C3 bus, add support for them. Signed-off-by:
-
Anson Huang authored
Add MAX7322 IO expander support. Signed-off-by:
-
Anson Huang authored
Add pfuze100 support on i.MX6SX Sabre Auto board. Signed-off-by:
-
Shawn Guo authored
The board specific pinctrl function container node 'imx6x-sabreauto' is not really necessary, since commit 5fcdf6a7 ("pinctrl: imx: Allow parsing DT without function nodes"). Let's drop it to save one level of indentation. Signed-off-by:
-
Shawn Guo authored
Let's drop the 'regulators' container node by giving VCC_SD3 an unique name and removing 'reg' property, so that the fixed regulator can be under root node directly. Signed-off-by: -
Fabio Estevam authored
The 'fsl,uart-has-rtscts' property is deprecated and it is recommended to use the generic 'uart-has-rtscts' property instead. Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warning: arch/arm/boot/dts/imx6q-var-dt6customboard.dtb: Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warning: arch/arm/boot/dts/imx6q-utilite-pro.dtb: Warning (avoid_unnecessary_addr_size): /encoder: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warnings: arch/arm/boot/dts/imx6q-b850v3.dtb: Warning (avoid_unnecessary_addr_size): /soc/aips-bus@2100000/i2c@21a4000/mux@70/i2c@1/stdp2690@72: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/boot/dts/imx6q-b850v3.dtb: Warning (avoid_unnecessary_addr_size): /soc/aips-bus@2100000/i2c@21a4000/mux@70/i2c@1/stdp4028@73: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warning: arch/arm/boot/dts/imx6dl-aristainetos2_4.dtb: Warning (avoid_unnecessary_addr_size): /soc/aips-bus@2000000/spba-bus@2000000/ecspi@2008000/display@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warnings: arch/arm/boot/dts/imx53-ppd.dtb: Warning (avoid_unnecessary_addr_size): /power-gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/boot/dts/imx53-ppd.dtb: Warning (avoid_unnecessary_addr_size): /touch-lock-key: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warnings: arch/arm/boot/dts/imx6q-novena.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@2400000/port@2: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/boot/dts/imx6q-novena.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@2400000/port@3: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/boot/dts/imx6q-novena.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@2800000/port@2: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/boot/dts/imx6q-novena.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@2800000/port@3: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warnings: arch/arm/boot/dts/imx6q-novena.dtb: Warning (avoid_unnecessary_addr_size): /soc/aips-bus@2100000/i2c@21a0000/stmpe811@44: unnecessary #address-cells/#size-cells without "ranges" or child "reg" Signed-off-by:
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells from the switch nodes to fix the following DTC warnings: arch/arm/boot/dts/imx6q-b450v3.dtb: Warning (avoid_unnecessary_addr_size): /mdio-gpio/switch@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
-
- 03 May, 2018 1 commit
-
-
Fabio Estevam authored
Remove unnecessary #address-cells/#size-cells to fix the following DTC warnings: arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (avoid_unnecessary_addr_size): /soc/aips-bus@2100000/mipi@21e0000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by:
-
- 02 May, 2018 4 commits
-
-
Sebastian Reichel authored
Replace magic numbers with IRQ_TYPE_* constants to improve DT readability. Signed-off-by:
Ezequiel Garcia <ezequiel@collabora.com> Signed-off-by:
-
Anson Huang authored
On i.MX6SX SabreAuto board, there is external 24MHz clock source for analog clock2, add this clock source to clock tree and remove "clocks" container for all input clocks. Signed-off-by:
-
Stefan Wahren authored
The iMX6ULL UART5_RTS_B_DATA_SELECT_INPUT DAISY Register has some different bit definitions to that same register in the i.MX6UL. The bits for the i.MX6UL: 000 CSI_DATA03_ALT8 — Selecting Pad: CSI_DATA03 for Mode: ALT8 001 GPIO1_IO08_ALT8 — Selecting Pad: GPIO1_IO08 for Mode: ALT8 010 GPIO1_IO09_ALT8 — Selecting Pad: GPIO1_IO09 for Mode: ALT8 011 ENET1_RX_EN_ALT1 — Selecting Pad: ENET1_RX_EN for Mode: ALT1 100 ENET1_TX_DATA0_ALT1 — Selecting Pad: ENET1_TX_DATA0 for Mode: ALT1 101 CSI_DATA02_ALT8 — Selecting Pad: CSI_DATA02 for Mode: ALT8 But for the i.MX6ULL: 000 CSI_DATA03_ALT8 — Selecting Pad: CSI_DATA03 for Mode: ALT8 001 GPIO1_IO08_ALT8 — Selecting Pad: GPIO1_IO08 for Mode: ALT8 010 GPIO1_IO09_ALT8 — Selecting Pad: GPIO1_IO09 for Mode: ALT8 011 UART1_CTS_B_ALT9 — Selecting Pad: UART1_CTS_B for Mode: ALT9 100 UART1_RTS_B_ALT9 — Selecting Pad: UART1_RTS_B for Mode: ALT9 101 ENET1_RX_EN_ALT1 — Selecting Pad: ENET1_RX_EN for Mode: ALT1 110 ENET1_TX_DATA0_ALT1 — Selecting Pad: ENET1_TX_DATA0 for Mode: ALT1 111 CSI_DATA02_ALT8 — Selecting Pad: CSI_DATA02 for Mode: ALT8 Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Fabio Estevam authored
Add CAAM support on i.MX6UL. Also, since CAAM is not available on i.MX6ULL the CAAM node needs to be deleted in the imx6ull.dtsi. Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
-
- 23 Apr, 2018 5 commits
-
-
Lucas Stach authored
This touchscreen is present instead of the RMI4 touch on some SKUs of the RDU2. Keep it disabled by default, the bootloader will enable it instead of the RMI4 touch when running on one of those units. Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Tested-by:
Chris Healy <cphealy@gmail.com> Signed-off-by:
-
Lucas Stach authored
This downclocks the shader domain from 720MHz to 594MHz, which gets rid of brown-outs due to excessive current draw on the PMIC switchers. The board has an unchanged power tree from the Quad design, which isn't able to cope with higher current needs of the QuadPlus GPU at full speed. Signed-off-by:
-
Lucas Stach authored
This bumps the SoC/PU domain operating points by 25mV, giving a total of 75mV margin to the minimum required voltages. This gets rid of brown-outs seen due to voltage drop-out on the board. Signed-off-by:
-
Fabio Estevam authored
The 'bus-format-override' property is not documented nor used anywhere else, so just remove it. Reported-by:
-
Lukasz Majewski authored
This commit adds device tree description of Kieback & Peter GmbH iMX6Q TPC board. Signed-off-by:
Lukasz Majewski <lukma@denx.de> Reviewed-by:
-
- 18 Apr, 2018 3 commits
-
-
Greg Ungerer authored
The iMX6ULL UART5_RX_DATA_SELECT_INPUT DAISY Register has some different bit definitions to that same register in the iMX6UL. The bits for the iMX6UL: 000 CSI_DATA00_ALT8 — Selecting Pad: CSI_DATA00 for Mode: ALT8 001 CSI_DATA01_ALT8 — Selecting Pad: CSI_DATA01 for Mode: ALT8 010 GPIO1_IO04_ALT8 — Selecting Pad: GPIO1_IO04 for Mode: ALT8 011 GPIO1_IO05_ALT8 — Selecting Pad: GPIO1_IO05 for Mode: ALT 100 UART5_TX_DATA_ALT0 — Selecting Pad: UART5_TX_DATA for Mode: ALT 101 UART5_RX_DATA_ALT0 — Selecting Pad: UART5_RX_DATA for Mode: ALT But for the iMX6ULL: 000 CSI_DATA00_ALT8 — Selecting Pad: CSI_DATA00 for Mode: ALT8 001 CSI_DATA01_ALT8 — Selecting Pad: CSI_DATA01 for Mode: ALT8 010 GPIO1_IO04_ALT8 — Selecting Pad: GPIO1_IO04 for Mode: ALT8 011 GPIO1_IO05_ALT8 — Selecting Pad: GPIO1_IO05 for Mode: ALT 100 UART1_TX_DATA_ALT9 — Selecting Pad: UART1_TX_DATA for Mode: ALT9 101 UART1_RX_DATA_ALT9 — Selecting Pad: UART1_RX_DATA for Mode: ALT9 110 UART5_TX_DATA_ALT0 — Selecting Pad: UART5_TX_DATA for Mode: ALT0 111 UART5_RX_DATA_ALT0 — Selecting Pad: UART5_RX_DATA for Mode: ALT0 Specifically for a board I am working on with the serial console on UART5 I need to be able to enable UART5_RX_DATA_ALT0 mode. There is no definition for the iMX6ULL version of that in imx6ul-pinfunc.h or imx6ull-pinfunc.h. Add definitions for the missing UART5 input select register bits of the iMX6ULL. Signed-off-by:
Greg Ungerer <gerg@linux-m68k.org> Acked-by:
-
Jagan Teki authored
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for Android and video capture application. notable features: CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz Memory Up to 2 GB DDR3-1066 Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4 port 8 bit CSI INPUT MIPI-CSI INPUT 1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc Signed-off-by:
Jagan Teki <jagan@amarulasolutions.com> Signed-off-by:
-
Jagan Teki authored
Switch to use koe_tx31d200vm0baa LVDS timings from panel-simple instead hard coding the same in dts. Signed-off-by:
-
- 16 Apr, 2018 9 commits
-
-
Marek Vasut authored
Add support for the DH i.MX6 Quad based SoM and a PDK2 evaluation board. The evaluation board features three serial ports, USB OTG, USB host with an USB hub, Fast or Gigabit ethernet, eMMC, uSD, SD, mSATA, analog audio, PCIe and HDMI video output. All of the aforementioned features are supported by this patch. Signed-off-by:
Marek Vasut <marex@denx.de> Reviewed-by:
-
Anson Huang authored
Add i.MX7S/D anatop vdd1p2 regulator. Signed-off-by:
-
Anson Huang authored
Add support for imx7d-sdb board's gpio keys: S1(FUNC1): KEY_VOLUMEUP S3(FUNC2): KEY_VOLUMEDOWN Signed-off-by:
Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by:
-
Fabio Estevam authored
Move tempmon node from soc node to root node. tempmon node does not have any register properties and thus shouldn't be placed on the bus. This fixes the following build warning with W=1: arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@30000000/tempmon missing or empty reg/ranges property Fixes: de25b9bb ("ARM: dts: imx7s: add temperature monitor support") Signed-off-by:
-
Shengjiu Wang authored
Update SAI select input daisy chain value according to Reference Manual. Signed-off-by:
Shengjiu Wang <shengjiu.wang@nxp.com> Signed-off-by:
-
Matt Porter authored
The HB onboard audio currently makes use of the imx-audio-sgtl5000 binding. This binding does not support auxiliary audio devices such as external amplifiers. The simple-audio-card binding does support this property which allows systems incorporating the HB to add an auxiliary device that's attached to the HB audio jack with an overlay. Convert the HB onboard audio to use simple-audio-card for this additional flexibility. Signed-off-by:
Matt Porter <mporter@konsulko.com> Reviewed-by:
-
Jagan Teki authored
This patch adds initial support for BTicino i.MX6DL Mamoj board. Signed-off-by:
Simone CIANNI <simone.cianni@bticino.it> Signed-off-by:
Raffaele RECALCATI <raffaele.recalcati@bticino.it> Reviewed-by:
-
Jagan Teki authored
Added 'bticino' vendor prefix for Bticino International. Signed-off-by:
-
Fabio Estevam authored
sgtl5000 codec needs MCLK clock to be present so that it can successfully read/write via I2C. In the case of wandboard, MCLK is provided via MX6QDL_PAD_GPIO_0__CCM_CLKO1 pad. Move the MCLK pinctrl from hog group to the codec group, so that the codec clock can be present prior to reading the codec ID. This avoids the following error that happens from time to time: [ 2.484443] sgtl5000 1-000a: Error reading chip id -6 Signed-off-by:
-
