- 01 Oct, 2012 1 commit
-
-
Mauro Carvalho Chehab authored
tda1004x doesn't allow firmware loads while it is busy with something else. Avoid it to happen by locking the I2C bus during firmware transfer. Signed-off-by:Mauro Carvalho Chehab <mchehab@redhat.com>
-
- 28 Sep, 2012 1 commit
-
-
Mauro Carvalho Chehab authored
The previous website doesn't exist anymore. Update it to one site that actually exists. Signed-off-by:
-
- 27 Sep, 2012 38 commits
-
-
Shawn Guo authored
Use managed functions to clean up the error handling code and function mx2_camera_remove(). Along with the change, a few variables get removed from struct mx2_camera_dev. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Acked-by:
Sascha Hauer <s.hauer@pengutronix.de> Acked-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Tested-by:
Javier Martin <javier.martin@vista-silicon.com> Signed-off-by:
-
Shawn Guo authored
This is a piece of code becoming dead since commit 2c9ba37d ([media] V4L: mx2_camera: remove unsupported i.MX27 DMA mode, make EMMA mandatory). It should have been removed together with the commit. Remove it now. Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
Callbacks were set even attach failed. This leads calling .release() in error case and resulted crash. Reported-by:
Oliver Schinagl <oliver@schinagl.nl> Signed-off-by:
-
Antti Palosaari authored
Callbacks were set even attach failed. This leads calling .release() in error case and resulted crash. Reported-by:
-
Antti Palosaari authored
fe was not set NULL after it was destroyed in tuner attach fail error case. Due to that it was destroyed again and Kernel oopsed. Reported-by:
-
Antti Palosaari authored
* better readability * make checkpatch.pl happy * few bytes smaller binary footprint Signed-off-by:
-
Antti Palosaari authored
Refactor firmware download function. It also should fix one bug coming from usb_control_msg() message buffers. Taking buffers from the stack for usb_control_msg() is not allowed as it does not work on all architectures. Allocate buffers using kmalloc(). Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
It is 4 x RTL2832U + 4 x FC0012 in one PCIe board. Of course there is a PCIe USB host controller too. Big thanks for Darryl Bond reporting and testing that! Reported-by:
Darryl Bond <darryl.bond@gmail.com> Tested-by:
-
Oliver Schinagl authored
This is initial support for the Asus MyCinema U3100Mini Plus. The driver in its current form gets detected and loads properly. Scanning using dvbscan works without problems, Locking onto a channel using tzap also works fine. Only playback using tzap -r + mplayer was tested and was fully functional. It uses the af9035 USB Bridge chip, with an af9033 demodulator. The tuner used is the FCI FC2580. Signed-off-by:
-
Antti Palosaari authored
Do not abuse anymore fc0012 tuner config. Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
It is just stub implementation, remove it. Also add debug for beginning of fe callback. Signed-off-by:
-
Antti Palosaari authored
Move rtl2831u tuner probing correct place. Signed-off-by:
-
Antti Palosaari authored
Use of frontend callback is highly hardware design dependent and whole callback could be optional in many cases. Returning error by default when callback is not implemented is stupid. Signed-off-by:
-
Antti Palosaari authored
Implement masked register write and use it. Signed-off-by:
-
Antti Palosaari authored
Move rtl2832u tuner probing correct place. Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Logically it is better ask hardware to stop streaming before killing urbs carrying stream. Earlier it was just opposite. Now code runs: * submit urbs * start streaming ** streaming ongoing ** * stop streaming * kill urbs Signed-off-by:
-
Antti Palosaari authored
I think it is better name. At that phase renaming is quite painless as module is not yet merged to mainline Kernel. Signed-off-by:
-
Antti Palosaari authored
Currently there is LNA behind cxd2820r demodulator GPIO. Use Kernel GPIO interface to access those GPIOs. Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Demodulator cannot perform statistic IOCTLs when it is not tuned. Return -EAGAIN in such case. Signed-off-by:
-
Sachin Kamat authored
Fixes checkpatch warnings related to printk. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Acked-by:
Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Peter Senna Tschudin authored
Convert a nonnegative error return code to a negative one, as returned elsewhere in the function. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> ( if@p1 (\(ret < 0\|ret != 0\)) { ... return ret; } | ret@p1 = 0 ) ... when != ret = e1 when != &ret *if(...) { ... when != ret = e2 when forall return ret; } // </smpl> Signed-off-by:
Peter Senna Tschudin <peter.senna@gmail.com> [laurent.pinchart@ideasonboard.com Replaced EBUSY with ENODEV] Signed-off-by:
-
Wanlong Gao authored
At commit 07d106d0, Linus pointed out that ENOIOCTLCMD should be translated as ENOTTY to user mode. Signed-off-by:
Wanlong Gao <gaowanlong@cn.fujitsu.com> Signed-off-by:
-
Antti Palosaari authored
Also change location of other RTL2832 reference design ID 0bda:2838. I just like to see reference design IDs at the first IDs in the list. Signed-off-by:
-
Shubhrajyoti D authored
Convert the struct i2c_msg initialization to C99 format. This makes maintaining and editing the code simpler. Also helps once other fields like transferred are added in future. Signed-off-by:
Shubhrajyoti D <shubhrajyoti@ti.com> Signed-off-by:
-
Shubhrajyoti D authored
Convert the struct i2c_msg initialization to C99 format. This makes maintaining and editing the code simpler. Also helps once other fields like transferred are added in future. Signed-off-by:
-
Shubhrajyoti D authored
Convert the struct i2c_msg initialization to C99 format. This makes maintaining and editing the code simpler. Also helps once other fields like transferred are added in future. Signed-off-by:
-
Shubhrajyoti D authored
Convert the struct i2c_msg initialization to C99 format. This makes maintaining and editing the code simpler. Also helps once other fields like transferred are added in future. Signed-off-by:
-
Shubhrajyoti D authored
Convert the struct i2c_msg initialization to C99 format. This makes maintaining and editing the code simpler. Also helps once other fields like transferred are added in future. Signed-off-by:
-
Shubhrajyoti D authored
Convert the struct i2c_msg initialization to C99 format. This makes maintaining and editing the code simpler. Also helps once other fields like transferred are added in future. Signed-off-by:
-
Ezequiel Garcia authored
This replaces BUG_ON() calls with WARN_ON(), and returns EINVAL if some parameter is NULL, as suggested by Jonathan and Mauro. The BUG_ON() call is too drastic to be used in this case. See the full discussion here: http://www.spinics.net/lists/linux-media/msg52462.htmlSigned-off-by:
Ezequiel Garcia <elezegarcia@gmail.com> Signed-off-by:
-
Ezequiel Garcia authored
This function returns an integer and it's mandatory to check the return code. Signed-off-by:
-
