Conflicts:
	arch/arm/common/sa1111.c
	arch/arm/mach-sa1100/neponset.c

Fixed:
	arch/arm/mach-sa1100/assabet.c
for the neponset changes

Add the .reset method to the HCD, and update the .start method
accordingly for this change.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add OHCI shutdown methods to cleanly shutdown the OHCI controller on
system shutdowns and reboots.  This avoids the controller continuing
to run should be soft-reboot the platform, potentially scribbling
over system memory.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Combine usb_hcd_sa1111_probe() and ohci_hcd_sa1111_drv_probe(), doing
the same for the remove methods.

Move sa1111_start_hc and sa1111_stop_hc to be located next to these
the probe/release functions, as they're only called from them.

Get rid of the /*----*/ breaker lines.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Use dev_dbg() instead, it's more friendly.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Clean up the ohci-sa1111 driver formatting to be more compliant with
current standards, and add 'static' to various function definitions
to avoid sparse complaints about undeclared functions.  Remove the
unnecessary local declaration of 'usb_disabled', which can be found
instead in linux/usb.h.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The sa1111 support will ioremap() the device; there is no need for
platforms to setup a static mapping for this.  Remove the static
mapping for this device from badge4, jornada720 and neponset.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Use dev_err() to report device specific errors rather than printk().
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Move the releasing of resources out of the release function - this
allows a cleaner and more conventional arrangement of the registration
failure paths and a saner unregistration process for these devices.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

It's pointless registering the PS/2 interfaces with the dmabounce code
when there's no DMA support for these in hardware, so only setup the
DMA masks for two subdevices which support DMA - the OHCI and SAC.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Use the bus notifier to register sa1111 devices with dmabounce, rather
than after the device has been registered, potentially racing with
driver binding.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Move the USB interface register definitions into the driver, rather
than keeping them in a common place.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Move the PCMCIA interface register definitions into the driver, rather
than keeping them in a common place.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Move the PS/2 interface register definitions into the driver, rather
than keeping them in a common location.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Get rid of the unused GPIO register definitions - we access GPIO
registers through the base + offset method, and having the phys
address definitions is unnecessary duplication.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Some platforms don't want certain devices to be registered, because,
eg, the interface is not wired.  Provide a way for platforms to
prevent various devices from being registered via a devid bitmask in
the platform data.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Change the sa1111 device id to be a bitmask.  This allows us to
specify the actual device, while allowing a single driver to bind
to both PS2 devices.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Move the handling of the 5v supply into badge4.c, removing this board
specific detail from the sa1111 ohci driver.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add platform hooks to be called when individual sa1111 devices are
enabled and disabled.  This will allow us to move some platform
specifics out of the individual drivers.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add a shutdown hook to the sa1111_driver structure to allow drivers
to be notified of system reboots and shutdowns.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Implement the necessary allocation/freeing functionality to support
sparse IRQs with the SA-1111 device.  On non-sparse IRQ platforms,
this allows us to dynamically allocate from within the available IRQ
number space.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit 19851c58 (sa1111: allow cascaded IRQs to be used by platforms)
moved the IRQ definitions to the .c file, and added an irq_base member
to the private data structure.

The inerrupt demultiplexer uses irq_base, but the interrupt setup code
does not.  Also, although the commit adds a private data structure to
pass this data, it isn't even referenced, resulting in irq_base being
zero.

We also copied the IRQ numbers from the device info array into the actual
devices, resulting in wrong interrupt numbers passed to the sub-devices.

The net effect of this is that we always overwrite IRQs 0-54, even if
they are allocated elsewhere in the system.

Add the code necessary to setup the private irq_base, and use it in the
IRQ setup code.  Make the SA-1111 probe fail with -EINVAL if there is no
platform data provided.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add a .owner initializer to the sa1111 driver structures to allow
allow the modules to be associated with their driver structures.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add an initializer for the struct device_driver .owner member.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We should not write to the SA1111 registers after setting the SLEEP
bit.  Moreover, the manual says that the PWM registers should be
disabled before we enter sleep.  So, move the clearing of these
registers earlier in the suspend sequence.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We weren't re-enabling the memory request/grant signals on resume,
causing DMA devices on the sa1111 to fail.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Now that we ioremap() the neponset register space, there's no need
to static map the neponset registers.  Get rid of this static mapping.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Move the board specific neponset register definitions to the board
file, rather than mach/neponset.h.  However, as the NCR_0 register
definitions are used by some drivers, leave these behind.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The neponset board is a daughter board for the Assabet.  Create the
neponset platform device in assabet.c, where we don't have to wrap
it with machine_is_assabet() stuff.  We also create this device
dynamically rather than keeping it as a static device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Suspend and resume in the _noirq state, so that we're saving the
state of the modem control signals as late as possible, and restoring
them as early as possible.  There's nothing to do in thaw/poweroff
methods as we've already saved the necessary state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Complete the neponset device resources by covering the children's
memory resources in the parent neponset device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Obtain the parent IRQ from the neponset device resource rather than
hard-coding it into the code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Implement the necessary allocation/freeing functionality to support
sparse IRQs with the Neponset device.  On non-sparse IRQ platforms,
this allows us to dynamically allocate from within the available IRQ
number space.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Use platform_device_register_full() to dynamically create the various
neponset child platform devices, and place them below the neponset
device itself to ensure proper PM ordering and device structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Save and restore the modem output control register across a suspend/
resume, as well as the NCR register.  Place these in a locally
allocated data structure rather than needing a new static variable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Ensure that the driver .owner field is properly initialized.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Move the IRQ handler along side the rest of the IRQ code, and rearrange
the include files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Rather than having direct register accesses to NCR_0 scattered amongst
the code, provide a function instead.  This contains the necessary
race protection for this platform, ensuring that updates to this
register are safe.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Since ARM was converted to genirq, the neponset IRQ implementation has
gradually broken as a result of various subtle changes being introduced
into genirq.

It used to be that simple IRQs did not need an IRQ chip.  This is no
longer the case, and genirq barfs in irq_set_handler().  Fix this by
introducing a dummy no-op chip, and registering it along with the flow
handler.

Neponset IRQs really don't have any masking ability - all we have is a
status register to allow us to decode the source, and a three input OR
gate inside a CPLD.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

GPIO27 is just connected to a CPLD input without any pull-ups or pull-
downs.  If GPIO27 is left as an input, it will float around mid-supply,
which for CMOS inputs is the worst place for a pin to be.  Ensure that
this pin is driven.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>