Cleanup and error handling

 - add error handling in SPI bus driver with selecting clients
 - use proper defines to access Blackfin MMRs
 - remove useless SSYNCs
 - cleaner use of portmux calls
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use new Blackfin portmux interface, add error handling.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Initial BF54x SPI support

 - support BF54x SPI0
 - clean up some code (whitespace etc)
 - will support multiports in the future
 - start using portmux calls
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Given the patch which simplifies the spi_sync calling convention, this one
updates the callers of that routine which tried using it according to the
previous specification.  (Most didn't.)
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Simplify spi_sync calling convention, eliminating the need to check both
the return value AND the message->status.  In consequence, this corrects
misbehaviours of spi_read and spi_write (which only checked the former) and
their callers.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add comment to at25 driver that it's for EEPROM chips, not FLASH
chips ... the AT25 series has both types of chip, and sometimes
they're even pin-compatible.  The command sets are different, as
is the treatment of erasure.  (FLASH needs explicit erasure, but
with EEPROM it's implicit.)  Note that all vendors seem to have
this same confusion in their *25* series SPI memory parts.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Make spi_write_then_read() use a mutex not a binary semaphore.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/slub.c exports ksize(), but mm/slob.c and mm/slab.c don't.

It's used by binfmt_flat, which can be built as a module.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

this call should use the array index j, not i.  But with this approach, just
one int i is enough, int j is not needed.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch fixes regression, introduced since 2.6.16.  NextStep variant of
UFS as OpenStep uses directory block size equals to 1024.  Without this
change, ufs_check_page fails in many cases.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Evgeniy Dushistov <dushistov@mail.ru>
Cc: Dave Bailey <dsbailey@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We must make sure that the RTC_DEV_BUSY flag has proper lock semantics,
i.e.  that the RTC_DEV_BUSY stores clearing the flag don't get reordered
before the preceeding stores and loads and vice versa.

Spotted by Nick Piggin.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently we are complicating the code in copy_process, the clone ABI, and
if we fix the bugs sys_setsid itself, with an unnecessary open coded
version of sys_setsid.

So just simplify everything and don't special case the session and pgrp of
the initial process in a pid namespace.

Having this special case actually presents to user space the classic linux
startup conditions with session == pgrp == 0 for /sbin/init.

We already handle sending signals to processes in a child pid namespace.

We need to handle sending signals to processes in a parent pid namespace
for cases like SIGCHILD and SIGIO.

This makes nothing extra visible inside a pid namespace.  So this extra
special case appears to have no redeeming merits.

Further removing this special case increases the flexibility of how we can
use pid namespaces, by not requiring the initial process in a pid namespace
to be a daemon.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

On 2.6.24, top started showing 100% iowait on one CPU when a UML instance was
running (but completely idle).  The UML code sits in io_getevents waiting for
an event to be submitted and completed.

Fix this by checking ctx->reqs_active before scheduling to determine whether
or not we are waiting for I/O.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'upstream-fixes' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  PHY: Add the phy_device_release device method.
  gianfar: fix compile warning
  pasemi_mac: Fix reuse of free'd skb
  SMC911X: Fix using of dereferenced skb after netif_rx
  sky2: recovery deadlock fix
  Fix memory corruption in fec_mpc52xx
  Don't claim to do IPv6 checksum offload
  cxgb - revert file mode changes.

Lately I've got this nice badness on mdio bus removal:

Device 'e0103120:06' does not have a release() function, it is broken and must be fixed.
------------[ cut here ]------------
Badness at drivers/base/core.c:107
NIP: c015c1a8 LR: c015c1a8 CTR: c0157488
REGS: c34bdcf0 TRAP: 0700   Not tainted  (2.6.23-rc5-g9ebadfbb-dirty)
MSR: 00029032 <EE,ME,IR,DR>  CR: 24088422  XER: 00000000
...
[c34bdda0] [c015c1a8] device_release+0x78/0x80 (unreliable)
[c34bddb0] [c01354cc] kobject_cleanup+0x80/0xbc
[c34bddd0] [c01365f0] kref_put+0x54/0x6c
[c34bdde0] [c013543c] kobject_put+0x24/0x34
[c34bddf0] [c015c384] put_device+0x1c/0x2c
[c34bde00] [c0180e84] mdiobus_unregister+0x2c/0x58
...

Though actually there is nothing broken, it just device
subsystem core expects another "pattern" of resource managment.

This patch implement phy device's release function, thus
we're getting rid of this badness.

Also small hidden bug fixed, hope none other introduced. ;-)
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Eliminate an uninitialized variable warning.  The code is correct, but
a pointer to the automatic variable 'addr' is passed to dma_alloc_coherent.
Since addr has never been initialized, and the compiler doesn't know
what dma_alloc_coherent will do with it, it complains.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Turns out we're freeing the skb when we detect CRC error, but we're
not clearing out info->skb. We could either clear it and have the stack
reallocate it, or just leave it and the rx ring refill code will reuse
the one that was allocated.

Reusing a freed skb obviously caused some nasty crashes of various kind,
as reported by Brent Baude and David Woodhouse.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Prevent deadlock in sky2 recovery logic. sky2_down calls napi_synchronize
which gets stuck if napi was already disabled.

Fix by rearranging slightly and not calling napi_disable until after
both ports are stopped. The napi_disable probably is being overly
paranoid, but it is safe now.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The mpc5200 fec driver is corrupting memory. This patch fixes two bugs
where the wrong skb was being referenced.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

revert inavertant file mode changes
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* Don't program UDMA timings when programming PIO or MWDMA modes.

  This has also a nice side-effect of fixing regression added by commit
  681c80b5 ("libata: correct handling of
  SRST reset sequences") (->set_piomode method for PIO0 is called before
  ->cable_detect method which checks UDMA timings to get the cable type).

* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tested-by: "Thomas Lindroth" <thomas.lindroth@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add the device IDs of legacy mode of MCP79 AHCI controller to ahci.c
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The Highpoint RocketRAID boards using Marvell 7042 chips
overwrite the 9th sector of attached drives at boot time,
when those drives are configured as "Legacy" (the default)
in the HighPoint BIOS.

This kills GRUB, and probably other stuff.
But it all happens *before* Linux is even loaded.

So, for now we'll log a WARNING when such boards are detected,
and advise users to configure BIOS "JBOD" volumes instead,
which don't appear to suffer from this problem.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

We need to run any DMA command with result taskfile requested in ADMA mode
when the port is in ADMA mode, otherwise it may try to use the legacy DMA engine
in ADMA mode which is not allowed. Enforce this with BUG_ON() since data
corruption could potentially result if this happened. Also, fail any attempt to
try and issue NCQ commands with result taskfile requested, since the hardware
doesn't allow this.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [S390] Make sure the restore psw masks are initialized.
  [S390] Fix compile error on 31bit without preemption
  [S390] dcssblk: prevent early access without own make_request function
  [S390] cio: add missing reprobe loop end statement
  [S390] cio: Issue SenseID per path.

* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
  x86: arch_register_cpu() section fix
  x86: free_cache_attributes() section fix
  x86: add the word 'WARNING' in check_nmi_watchdog() output
  x86: revert CONFIG_X86_HT semantics change

* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
  sched: default to more agressive yield for SCHED_BATCH tasks
  sched: fix crash in sys_sched_rr_get_interval()

I haven't seen Richard doing MTRR related work for quite some time, and
the "X86 ARCHITECTURE" entry in MAINTAINERS already covers the people
currently responsible for this code.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

SET_MODULE_OWNER() is obsolete.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fix this on i386 allnoconfig:

 WARNING: vmlinux.o(.text+0x6f2e): Section mismatch: reference to .init.text:register_cpu (between 'arch_register_cpu' and 'text_poke')
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

free_cache_attributes() must be __cpuinit since it calls the
__cpuinit cache_remove_shared_cpu_map().

This patch fixes the following section mismatch reported by
Chris Clayton:

 ...
 WARNING: vmlinux.o(.text+0x90b6): Section mismatch: reference to .init.text:cache_remove_shared_cpu_map (between 'free_cache_attributes' and 'show_level')
 ...
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Our automated test suite looks for keywords like error, fail, warning in
the boot log.  In the case when the nmi watchdog is determined to be
stuck in check_nmi_watchdog(), none of those keywords are displayed.

This patch adds a keyword, "WARNING:", so it makes it easier to notice
when the nmi watchdog isn't working correctly. Also add a proper
KERN_WARNING mark to this printout.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

The recent Kconfig changes in x86 resulted in CONFIG_X86_HT no longer
being set if (X86_32 && MK8).

After grep'ing through the tree I think the problem is that different
places have different assumptions about the semantics of CONFIG_X86_HT,
either:

- hyperthreading or
- multicore

This should be sorted out properly, but until then we should keep the
2.6.23 status quo.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

do more agressive yield for SCHED_BATCH tuned tasks: they are all
about throughput anyway. This allows a gentler migration path for
any apps that relied on stronger yield.
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Luiz Fernando N. Capitulino reported that sched_rr_get_interval()
crashes for SCHED_OTHER tasks that are on an idle runqueue.

The fix is to return a 0 timeslice for tasks that are on an idle
runqueue. (and which are not running, obviously)

this also shrinks the code a bit:

   text    data     bss     dec     hex filename
  47903    3934     336   52173    cbcd sched.o.before
  47885    3934     336   52155    cbbb sched.o.after
Reported-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

In case of TRACE_IRQFLAGS the restore psw masks will not be
initialized if noexec is turned on. This will lead to an
immediate system crash.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Commit b8e7a54c introduced a compile
error if CONFIG_PREEMPT is not set:

arch/s390/kernel/built-in.o: In function `cleanup_io_leave_insn':
/space/kvm/arch/s390/kernel/entry.S:(.text+0xbfce): undefined reference to `preempt_schedule_irq'

This patch hides preempt_schedule_irq if CONFIG_PREEMPT is not set.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

When loading a dcss segment with the dcssblk driver, sometimes the
following kind of message appears:

bio too big device dcssblk0 (8 > 0)
Buffer I/O error on device dcssblk0, logical block 172016
..

The fix is to move the disk registration after setting the
make_request function, to avoid calls into generic_make_request
for dcssblock without having the make_request function set up
properly.

Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>